ST / X_NUCLEO_IDB0XA1

BLE_API wrapper library for STMicroelectronics' BlueNRG Bluetooth Low Energy expansion board shield (Component)

Dependents:   Nucleo_Zumo_BLE_IDB04A1 contest_IOT5 contest_IOT6 contest_IOT_10 ... more

Fork of X_NUCLEO_IDB0XA1 by ST Expansion SW Team

Arduino Connector Compatibility Warning

X-NUCLEO-IDB04A1 and X-NUCLEO-IDB05A1 are Arduino compatible with an exception: instead of using pin D13 for the SPI clock, they use pin D3. The default configuration for this library is having the SPI clock on pin D3.

To be fully Arduino compatible, X-NUCLEO-IDB04A1 and X-NUCLEO-IDB05A1 need a small HW patch.

For X-NUCLEO-IDB04A1 this patch consists in removing zero resistor R10 and instead soldering zero resistor R11. For X-NUCLEO-IDB05A1 this patch consists in removing zero resistor R4 and instead soldering zero resistor R6.

In case you patch your board, then you also have to configure this library to use pin D13 to drive the SPI clock (see macro IDB0XA1_D13_PATCH in file x_nucleo_idb0xa1_targets.h).

If you use pin D13 for the SPI clock, please be aware that on STM32 Nucleo boards you may not drive the LED, otherwise you will get a conflict: the LED on STM32 Nucleo boards is connected to pin D13.

Referring to the current list of tested platforms (see X-NUCLEO-IDB04A1 and X-NUCLEO-IDB05A1 pages), the patch is required by ST-Nucleo-F103RB; ST-Nucleo-F302R8; ST-Nucleo-F411RE; and ST-Nucleo-F446RE.

Diff: source/BlueNRGGap.cpp

Branch:
af1d84618655ed0f9f8f0faa3591ab512645edf7
Revision:
302:ed6f74ab78f9
Parent:
293:5a1f577bf92f
--- a/source/BlueNRGGap.cpp	Thu Sep 15 10:52:09 2016 +0100
+++ b/source/BlueNRGGap.cpp	Thu Sep 15 10:52:11 2016 +0100
@@ -43,7 +43,7 @@
     #include "mbed-drivers/mbed.h"
 #else
     #include "mbed.h"
-#endif 
+#endif
 #include "ble_payload.h"
 #include "ble_utils.h"
 #include "ble_debug.h"
@@ -162,6 +162,27 @@
 
     }
 
+    // update the advertising data in the shield if advertising is running
+    if (state.advertising == 1) {
+        tBleStatus ret = hci_le_set_scan_resp_data(scanResponse.getPayloadLen(), scanResponse.getPayload());
+
+        if(BLE_STATUS_SUCCESS != ret) {
+            PRINTF(" error while setting scan response data (ret=0x%x)\n", ret);
+            switch (ret) {
+                case BLE_STATUS_TIMEOUT:
+                    return BLE_STACK_BUSY;
+                default:
+                    return BLE_ERROR_UNSPECIFIED;
+            }
+        }
+
+        ret = hci_le_set_advertising_data(advData.getPayloadLen(), advData.getPayload());
+        if (ret) {
+            PRINTF("error while setting the payload\r\n");
+            return BLE_ERROR_UNSPECIFIED;
+        }
+    }
+
     _advData = advData;
     _scanResponse = scanResponse;
 
@@ -1423,4 +1444,4 @@
 void BlueNRGGap::setGapRole(Role_t role)
 {
     gapRole = role;
-}
+}
\ No newline at end of file