Austin Dong
Setup and test the Adafruit HUZZAH ESP8266 Wi Fi SOC. Sets SSID and PASSWORD and prints status messages. For use on mbed LPC1768. See https://developer.mbed.org/users/ausdong/notebook/using-the-adafruit-huzzah-esp8266-to-add-wi-fi-to-/
Fork of
ESP8266-configuration-mbed-LPC1768
by 
jim hamblen
Diff: main.cpp
- Revision:
- 0:5ebf44bd3694
- Child:
- 1:4a9cc6d8c33d
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp Tue Feb 10 16:28:26 2015 +0000
@@ -0,0 +1,124 @@
+#include "mbed.h"
+
+Serial pc(USBTX, USBRX);
+Serial esp(PTE0, PTE1); // tx, rx
+
+Timer t;
+
+int count,ended,timeout;
+char buf[1024];
+char snd[255];
+
+char ssid[32] = "NETGEAR21"; // enter router ssid inside the quotes
+char pwd [32] = "PANASONIC"; // enter router password inside the quotes
+
+void SendCMD(),getreply(),ESPconfig(),ESPsetbaudrate();
+
+
+int main() {
+
+ pc.baud(115200); // set what you want here depending on your terminal program speed
+ esp.baud(115200); // change this to the new ESP8266 baudrate if it is changed at any time.
+
+ //ESPsetbaudrate(); //****************** include this routine to set a different ESP8266 baudrate ******************
+
+ ESPconfig(); //****************** include Config to set the ESP8266 configuration ***********************
+
+}
+
+// Sets new ESP8266 baurate, change the esp.baud(xxxxx) to match your new setting once this has been executed
+void ESPsetbaudrate()
+{
+ strcpy(snd, "AT+CIOBAUD=115200\r\n"); // change the numeric value to the required baudrate
+ SendCMD();
+}
+
+// +++++++++++++++++++++++++++++++++ This is for ESP8266 config only, run this once to set up the ESP8266 +++++++++++++++
+void ESPconfig()
+{
+
+ pc.printf("---------- Starting ESP Config ----------\r\n\n");
+ wait(2);
+ pc.printf("---------- Reset & get Firmware ----------\r\n");
+ strcpy(snd,"AT+RST\r\n");
+ SendCMD();
+ timeout=2;
+ getreply();
+ pc.printf(buf);
+
+ wait(1);
+
+
+ pc.printf("\n---------- Get Version ----------\r\n");
+ strcpy(snd,"AT+GMR\r\n");
+ SendCMD();
+ timeout=1;
+ getreply();
+ pc.printf(buf);
+
+
+ wait(1);
+ // set CWMODE to 1=Station,2=AP,3=BOTH, default mode 1 (Station)
+ pc.printf("\n---------- Setting Mode ----------\r\n");
+ strcpy(snd, "AT+CWMODE=1\r\n");
+ SendCMD();
+ timeout=1;
+ getreply();
+ pc.printf(buf);
+
+ wait(1);
+
+ pc.printf("\n---------- Listing Acces Points ----------\r\n");
+ strcpy(snd, "AT+CWLAP\r\n");
+ SendCMD();
+ timeout=3;
+ getreply();
+ pc.printf(buf);
+
+ wait(1);
+
+ pc.printf("\n---------- Connecting to AP ----------\r\n");
+ pc.printf("ssid = %s pwd = %s\r\n",ssid,pwd);
+ strcpy(snd, "AT+CWJAP=\"");
+ strcat(snd, ssid);
+ strcat(snd, "\",\"");
+ strcat(snd, pwd);
+ strcat(snd, "\"\r\n");
+ SendCMD();
+ timeout=8;
+ getreply();
+ pc.printf(buf);
+
+ wait(5);
+
+ pc.printf("\n---------- Get IP's ----------\r\n");
+ strcpy(snd, "AT+CIFSR\r\n");
+ SendCMD();
+ timeout=2;
+ getreply();
+ pc.printf(buf);
+
+ pc.printf("\n\n\n If you get a valid IP, ESP8266 has been set up.\r\n");
+ pc.printf(" Run this if you want to reconfig the ESP8266 at any time.\r\n");
+}
+
+void SendCMD()
+{
+ esp.printf("%s", snd);
+}
+
+void getreply()
+{
+ memset(buf, '\0', sizeof(buf));
+ t.start();
+ ended=0;count=0;
+ while(!ended) {
+ if(esp.readable()) {
+ buf[count] = esp.getc();count++;
+ }
+ if(t.read() > timeout) {
+ ended = 1;t.stop();t.reset();
+ }
+ }
+}
+
\ No newline at end of file