Prototype RF driver for STM Sub-1 GHz RF expansion board based on the SPSGRF-868 module for STM32 Nucleo.

Prototype RF Driver for STM Sub-1 GHz RF Expansion Boards based on the SPSGRF-868 and SPSGRF-915 Modules for STM32 Nucleo

Currently supported boards:

Note, in order to use expansion board X-NUCLEO-IDS01A4 in mbed you need to perform the following HW modifications on the board:

  • Unmount resistor R4
  • Mount resistor R7

Furthermore, on some Nucleo development boards (e.g. the NUCLEO_F429ZI), in order to be able to use Ethernet together with these Sub-1 GHz RF expansion boards, you need to compile this driver with macro SPIRIT1_SPI_MOSI=PB_5 defined, while the development board typically requires some HW modification as e.g. described here!

This driver can be used together with the 6LoWPAN stack (a.k.a. Nanostack).

Revision:
34:edda6a7238ec
Child:
67:93bec0baf1de
diff -r c226804be492 -r edda6a7238ec source/libs/Contiki_STM32_Library/platform-conf.h
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/source/libs/Contiki_STM32_Library/platform-conf.h	Tue Nov 22 11:40:10 2016 +0100
@@ -0,0 +1,197 @@
+/**
+******************************************************************************
+* @file    platform/stm32nucleo-spirit1/platform-conf.h
+* @author  System LAB 
+* @version V1.0.0
+* @date    17-May-2015
+* @brief   Configuration parameters
+******************************************************************************
+* @attention
+*
+* <h2><center>&copy; COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+*
+* Redistribution and use in source and binary forms, with or without modification,
+* are permitted provided that the following conditions are met:
+*   1. Redistributions of source code must retain the above copyright notice,
+*      this list of conditions and the following disclaimer.
+*   2. Redistributions in binary form must reproduce the above copyright notice,
+*      this list of conditions and the following disclaimer in the documentation
+*      and/or other materials provided with the distribution.
+*   3. Neither the name of STMicroelectronics nor the names of its contributors
+*      may be used to endorse or promote products derived from this software
+*      without specific prior written permission.
+*
+* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+*
+******************************************************************************
+*/
+/*---------------------------------------------------------------------------*/
+/**
+ * \addtogroup stm32nucleo-spirit1
+ * @{
+ *
+ * \defgroup stm32nucleo-spirit1-peripherals User Button on STM32 Nucleo
+ *
+ * Defines some of the platforms capabilities
+ * @{
+ *
+ * \file
+ * Header file for the stm32nucleo-spirit1 platform configuration
+ */
+/*---------------------------------------------------------------------------*/
+#ifndef __PLATFORM_CONF_H__
+#define __PLATFORM_CONF_H__
+/*---------------------------------------------------------------------------*/
+#ifdef USE_STM32L1XX_NUCLEO
+#include <inttypes.h>
+#include <string.h>
+/*---------------------------------------------------------------------------*/
+#define PLATFORM_HAS_LEDS 1
+#define PLATFORM_HAS_BUTTON 1
+#define PLATFORM_HAS_RADIO 1
+
+#define LEDS_GREEN  1 /*Nucleo LED*/
+#define LEDS_RED    2 /*SPIRIT1 LED*/
+
+#ifdef COMPILE_SENSORS
+#define LEDS_CONF_ALL 1 /*Can't use SPIRIT1 LED in this case*/
+#else
+#define LEDS_CONF_ALL 3 /*No sensors -> we can use SPIRIT1 LED in this case*/
+#endif /*COMPILE_SENSORS*/
+/*---------------------------------------------------------------------------*/
+#define F_CPU                   32000000ul
+#define RTIMER_ARCH_SECOND              32768   
+#define PRESCALER       ((F_CPU / (RTIMER_ARCH_SECOND*2)))
+
+#define UART1_CONF_TX_WITH_INTERRUPT        0
+#define WITH_SERIAL_LINE_INPUT              1
+#define TELNETD_CONF_NUMLINES               6
+#define NETSTACK_CONF_RADIO                 spirit_radio_driver
+#define NETSTACK_RADIO_MAX_PAYLOAD_LEN      96 /* spirit1-config.h */
+
+#if WITH_IP64
+#include "ip64-conf.h"
+#define WITH_SLIP 1
+#ifndef UIP_FALLBACK_INTERFACE
+#define UIP_FALLBACK_INTERFACE ip64_uip_fallback_interface
+#endif
+#endif /* WITH_IP64 */
+
+/*---------------------------------------------------------------------------*/
+/* define ticks/second for slow and fast clocks. Notice that these should be a
+  power of two, eg 64,128,256,512 etc, for efficiency as POT's can be optimized
+  well. */
+#define CLOCK_CONF_SECOND             128
+#define RELOAD_VALUE        ((F_CPU/CLOCK_CONF_SECOND) - 1)
+/* One tick: 62.5 ms */
+
+#define RTIMER_CLOCK_LT(a,b)     ((signed short)((a)-(b)) < 0)
+/*---------------------------------------------------------------------------*/
+typedef unsigned long clock_time_t;     
+typedef unsigned long long rtimer_clock_t; 
+/*---------------------------------------------------------------------------*/
+#define CC_CONF_REGISTER_ARGS          0
+#define CC_CONF_FUNCTION_POINTER_ARGS  1
+#define CC_CONF_FASTCALL
+#define CC_CONF_VA_ARGS                1
+#define CC_CONF_INLINE                 inline
+
+#define CCIF
+#define CLIF
+/*---------------------------------------------------------------------------*/
+typedef uint8_t         u8_t;
+typedef uint16_t        u16_t;
+typedef uint32_t        u32_t;
+typedef  int32_t        s32_t;
+typedef unsigned short  uip_stats_t;
+/*---------------------------------------------------------------------------*/
+#define MULTICHAN_CONF_SET_CHANNEL(x)
+#define MULTICHAN_CONF_READ_RSSI(x) 0
+/*---------------------------------------------------------------------------*/
+#endif//USE_STM32L1XX_NUCLEO
+
+#ifdef USE_STM32F4XX_NUCLEO
+#include <inttypes.h>
+#include <string.h>
+#include "main.h"
+/*---------------------------------------------------------------------------*/
+#define PLATFORM_HAS_LEDS 1
+#define PLATFORM_HAS_BUTTON 1
+#define PLATFORM_HAS_RADIO 1
+
+#define LEDS_GREEN  1 /*Nucleo LED*/
+#define LEDS_RED    2 /*SPIRIT1 LED*/
+
+#ifdef COMPILE_SENSORS
+#define LEDS_CONF_ALL 1 /*Can't use SPIRIT1 LED in this case*/
+#else
+#define LEDS_CONF_ALL 3 /*No sensors -> we can use SPIRIT1 LED in this case*/
+#endif /*COMPILE_SENSORS*/
+/*---------------------------------------------------------------------------*/
+#define F_CPU                   	84000000ul
+#define RTIMER_ARCH_SECOND          96000//32678
+//#define PRESCALER       			uwPrescalerValue
+
+#define UART1_CONF_TX_WITH_INTERRUPT        0
+#define WITH_SERIAL_LINE_INPUT              1
+#define TELNETD_CONF_NUMLINES               6
+#define NETSTACK_CONF_RADIO                 spirit_radio_driver
+#define NETSTACK_RADIO_MAX_PAYLOAD_LEN      96 /* spirit1-config.h */
+
+#if WITH_IP64
+#include "ip64-conf.h"
+#define WITH_SLIP 1
+#ifndef UIP_FALLBACK_INTERFACE
+#define UIP_FALLBACK_INTERFACE ip64_uip_fallback_interface
+#endif
+#endif /* WITH_IP64 */
+
+/*---------------------------------------------------------------------------*/
+/* define ticks/second for slow and fast clocks. Notice that these should be a
+  power of two, eg 64,128,256,512 etc, for efficiency as POT's can be optimized
+  well. */
+#define CLOCK_CONF_SECOND             512
+#define RELOAD_VALUE        ((F_CPU/CLOCK_CONF_SECOND) - 1)
+
+/* One tick: 62.5 ms */
+
+#define RTIMER_CLOCK_LT(a,b)     ((signed short)((a)-(b)) < 0)
+/*---------------------------------------------------------------------------*/
+typedef unsigned long clock_time_t;
+typedef unsigned long long rtimer_clock_t;
+/*---------------------------------------------------------------------------*/
+#define CC_CONF_REGISTER_ARGS          0
+#define CC_CONF_FUNCTION_POINTER_ARGS  1
+#define CC_CONF_FASTCALL
+#define CC_CONF_VA_ARGS                1
+#define CC_CONF_INLINE                 inline
+
+#define CCIF
+#define CLIF
+/*---------------------------------------------------------------------------*/
+typedef uint8_t         u8_t;
+typedef uint16_t        u16_t;
+typedef uint32_t        u32_t;
+typedef  int32_t        s32_t;
+typedef unsigned short  uip_stats_t;
+/*---------------------------------------------------------------------------*/
+#define MULTICHAN_CONF_SET_CHANNEL(x)
+#define MULTICHAN_CONF_READ_RSSI(x) 0
+/*---------------------------------------------------------------------------*/
+#endif//USE_STM32F4XX_NUCLEO
+
+#endif /* __PLATFORM_CONF_H__ */
+/*---------------------------------------------------------------------------*/
+/**
+ * @}
+ * @}
+ */