BLE_API wrapper library for STMicroelectronics' BlueNRG Bluetooth Low Energy expansion board shield (Component)
Dependents: Nucleo_Zumo_BLE_IDB04A1 contest_IOT5 contest_IOT6 contest_IOT_10 ... more
Fork of X_NUCLEO_IDB0XA1 by
Arduino Connector Compatibility Warning
X-NUCLEO-IDB04A1 and X-NUCLEO-IDB05A1 are Arduino compatible with an exception: instead of using pin D13
for the SPI clock, they use pin D3
.
The default configuration for this library is having the SPI clock on pin D3
.
To be fully Arduino compatible, X-NUCLEO-IDB04A1 and X-NUCLEO-IDB05A1 need a small HW patch.
For X-NUCLEO-IDB04A1 this patch consists in removing zero resistor R10
and instead soldering zero resistor R11
.
For X-NUCLEO-IDB05A1 this patch consists in removing zero resistor R4
and instead soldering zero resistor R6
.
In case you patch your board, then you also have to configure this library to use pin D13
to drive the SPI clock (see macro IDB0XA1_D13_PATCH
in file x_nucleo_idb0xa1_targets.h
).
If you use pin D13
for the SPI clock, please be aware that on STM32 Nucleo boards you may not drive the LED, otherwise you will get a conflict: the LED on STM32 Nucleo boards is connected to pin D13
.
Referring to the current list of tested platforms (see X-NUCLEO-IDB04A1 and X-NUCLEO-IDB05A1 pages), the patch is required by ST-Nucleo-F103RB; ST-Nucleo-F302R8; ST-Nucleo-F411RE; and ST-Nucleo-F446RE.
Diff: source/BlueNRGGap.cpp
- Revision:
- 203:5b9c78101d45
- Parent:
- 191:d22cc4715b0c
- Parent:
- 201:a9bc2e8b01d7
- Child:
- 212:8b5ff0f0186f
--- a/source/BlueNRGGap.cpp Fri Nov 20 16:59:49 2015 +0100 +++ b/source/BlueNRGGap.cpp Thu Dec 03 11:37:55 2015 +0100 @@ -468,9 +468,9 @@ } } - // If ADV Data Type is MANUFACTURER SPECIFIC, then the TxP is set implicitly - // (i.e., w/o calling setTxPower() - if(txPowerAdType || AdvData[1]==AD_TYPE_MANUFACTURER_SPECIFIC_DATA) { + // If ADV Data Type is SERVICE DATA or MANUFACTURER SPECIFIC DATA, + // we need to delete it to make the needed room in ADV payload + if(AdvData[1]==AD_TYPE_SERVICE_DATA || AdvData[1]==AD_TYPE_MANUFACTURER_SPECIFIC_DATA) { PRINTF("!!!calling aci_gap_delete_ad_type(AD_TYPE_TX_POWER_LEVEL)!!!\n"); ret = aci_gap_delete_ad_type(AD_TYPE_TX_POWER_LEVEL); if (BLE_STATUS_SUCCESS!=ret){ @@ -1207,12 +1207,13 @@ tBleStatus ret; int8_t enHighPower = 0; - int8_t paLevel = 0; -#ifdef DEBUG + int8_t paLevel = 0; + int8_t dbmActuallySet = getHighPowerAndPALevelValue(txPower, enHighPower, paLevel); -#else + +#ifndef DEBUG /* avoid compiler warnings about unused variables */ - (void)txPower; + (void)dbmActuallySet; #endif PRINTF("txPower=%d, dbmActuallySet=%d\n\r", txPower, dbmActuallySet); @@ -1221,8 +1222,7 @@ if(ret!=BLE_STATUS_SUCCESS) { return BLE_ERROR_UNSPECIFIED; } - - txPowerAdType = true; + return BLE_ERROR_NONE; }