ST
Motion and Environmental sensor reader application connected via BLE to ST BlueMS iOS/Android application.
Dependencies: HTS221 LIS3MDL LPS22HB LSM303AGR LSM6DSL
Fork of
MOTENV_Mbed
by 
ST Expansion SW Team
This application supports three different sets of ST hardware boards:
- STEVAL-STLKT01V1 (aka SensorTile)
- X-NUCLEO-IDB05A1 and X-NUCLEO-IKS01A2 expansion boards
- B-L475E-IOT01A IoT Discovery board
and runs over four different target configurations:
- Nucleo F401RE + X-NUCLEO-IDB05A1 + X-NUCLEO-IKS01A2 (set target NUCLEO_F401RE)
- DISCO_L475VG_IOT01A (set target DISCO_L475VG_IOT01A)
- Nucleo L476RG + CRADLE + SENSORTILE (set compile target NUCLEO_L476RG)
- Nucleo L476RG + CRADLE_EXPANSION_BOARD + SENSORTILE (set compile target NUCLEO_L476RG, remove macro MINI_CRADLE from mbed_app.json)
The first 2 configurations do not require any HW modifications (just use the above indicated targets).
Third configuration (CRADLE ) only requires to remove the two ST-LINK jumpers and JP6 from the Nucleo L476RG board in order to allow flashing the SensorTile through the Nucleo Jtag controller. Once flashed, if the battery is properly plugged and charged, the SensorTile could be mounted in the plastic enclosure being able to run as a small stand alone wearable device. Please note that this configuration do not provide a serial console for printf.
To enable last configuration (CRADLE_EXPANSION_BOARD), follow the steps below:
- On Nucleo L476RG
- open the two "ST-LINK" jumpers
- open the MCU power supply jumper JP6
- close the solder bridges SB63 and SB62 (to enable the serial console)
- On SensorTile Arduino Cradle close the solder bridges SB21 and SB10 (to enable the serial console) and move the jumper J2 to the 5V position
- Plug the Sensor Tile on the Arduino Cradle
- Plug the Cradle on the Nucleo Arduino connector and connect the debug flat cable between Cradle and Nucleo Jtag connector (the cradle pin1 -identified by a dot- must be connected to the Nucleo pin1 (dot) of SWD CN4 jtag connector)
- Plug the Nucleo USB cable on PC (a new COM port should appear); no need to plug the micro USB cable on the cradle.
- Open a PC terminal to see the messages
- Compile from mbed CLI or on-line compiler removing macro MINI_CRADLE from mbed_app.json file and selecting NUCLEO_ L476RG target
- Flash the board with the binary
For all configurations on an Android or iOS device download and open the ST BlueMS application and connect to "MotEnvMbedOS" BLE device to see the sensor data.
For all configurations is also possible to add a 9 axis MotionFX sensor fusion library, which is part of the X-CUBE-MEMS package at this link.
The library comes in three flavours, choose your preferred according to the toolchain used (IAR, Keil or GC, Keil version should be used for the online compiler) and copy it in the Middlewares\ST\STM32_MotionFX_Library\Lib directory changing the file extension according to the toolchain used (.a for GCC, .ar for Keil).
In the file mbed_app.json add the macro definition "USE_SENSOR_FUSION_LIB" to the chosen target.
If compiling from CLI and using GCC_ARM toolchain option, in the file \mbed-os\tools\toolchains\gcc.py change the compiling option from
if target.core == "Cortex-M4F":
self.cpu.append("-mfpu=fpv4-sp-d16")
self.cpu.append("-mfloat-abi=softfp")
to
if target.core == "Cortex-M4F":
self.cpu.append("-mfpu=fpv4-sp-d16")
self.cpu.append("-mfloat-abi=hard")
and compile.
Diff: main.cpp
- Revision:
- 25:9e720d968dc0
- Parent:
- 24:b374c444d8ad
- Child:
- 26:1bc571e52ad9
--- a/main.cpp Tue Oct 03 16:12:15 2017 +0000
+++ b/main.cpp Fri Oct 06 14:37:46 2017 +0000
@@ -72,14 +72,17 @@
#ifdef CUST_SENS_SERV
#include "CustomSensorsService.h"
+#define MINI_CRADLE
+#ifdef MINI_CRADLE
+#include "HTS221Sensor.h"
+static DevI2C devI2c (PC_1, PC_0);
+static HTS221Sensor ht_sensor (&devI2c); // sensor on the mini cradle only (not on the tile)
+#endif
+
#define SPI_TYPE_LPS22HB LPS22HBSensor::SPI3W
-#define SPI_TYPE_LSM6DSL LSM6DSLSensor::SPI3W
-//DevI2C i2c(I2C_SDA, I2C_SCL);
-//HTS221Sensor ht_sensor(&i2c); // sensor on the mini cradle only (not on the tile)
+#define SPI_TYPE_LSM6DSL LSM6DSLSensor::SPI3W
SPI sens_intf(PB_15, NC, PB_13); // 3W mosi, sclk on Nucleo L476 same as BTLE
-//LPS22HBSensor pt_sensor(&sens_intf, PA_3); // on SensorTile L476JG
static LPS22HBSensor pt_sensor(&sens_intf, PA_3, NC, SPI_TYPE_LPS22HB);
-//LSM6DSLSensor acc_gyro(&sens_intf, PB_12, NC, PA_2 ); // on SensorTile L476JG
static LSM6DSLSensor acc_gyro(&sens_intf,PB_12, NC, PA_2, SPI_TYPE_LSM6DSL);
static LSM303AGRMagSensor magnetometer(&sens_intf, PB_1 ); //on SensorTile L476JG
static LSM303AGRAccSensor accelerometer(&sens_intf, PC_4 ); //on SensorTile L476JG
@@ -438,7 +441,9 @@
p_customsensorservice->sendEnvTemperature(TempToSend, TimeStamp);
} else if (p_customsensorservice->isHumHandle(handle)) {
-// ht_sensor.get_humidity(&hum);
+#ifdef MINI_CRADLE
+ ht_sensor.get_humidity(&hum);
+#endif
floatToInt(hum, &intPart, &decPart, 1);
HumToSend = intPart*10+decPart;
p_customsensorservice->sendEnvHumidity(HumToSend, TimeStamp);
@@ -470,7 +475,9 @@
pt_sensor.get_temperature(&temp);
floatToInt(temp, &intPart, &decPart, 1);
TempToSend = intPart*10+decPart;
-// ht_sensor.get_humidity(&hum);
+#ifdef MINI_CRADLE
+ ht_sensor.get_humidity(&hum);
+#endif
floatToInt(hum, &intPart, &decPart, 1);
HumToSend = intPart*10+decPart;
pt_sensor.get_pressure(&pres);
@@ -813,7 +820,8 @@
}
if (p_customsensorservice->isHumNotificationEn()) {
-// err = ht_sensor.get_humidity(&hum);
+#ifdef MINI_CRADLE
+ err = ht_sensor.get_humidity(&hum);
if ( err != 0) {
printf ("= * ERROR %d GetHumidity\n\r", (int)err);
} else {
@@ -821,6 +829,7 @@
HumToSend = intPart*10+decPart;
p_customsensorservice->updateEnvHumidity(HumToSend, TimeStamp);
}
+#endif
}
if (p_customsensorservice->isPresNotificationEn()) {
@@ -842,13 +851,15 @@
floatToInt(pres, &intPart, &decPart, 1);
PresToSend = intPart*100+decPart;
}
-// err = ht_sensor.get_humidity(&hum);
+#ifdef MINI_CRADLE
+ err = ht_sensor.get_humidity(&hum);
if ( err != 0) {
printf ("= * ERROR %d GetHumidity\n\r", (int)err);
} else {
floatToInt(hum, &intPart, &decPart, 1);
HumToSend = intPart*10+decPart;
- }
+ }
+#endif
err = pt_sensor.get_temperature(&temp);
if ( err != 0) {
printf ("= * ERROR %d GetTemperature\n\r", (int)err);
@@ -954,8 +965,11 @@
magnetometer.enable();
accelerometer.enable();
acc_gyro.enable_g();
- acc_gyro.enable_x();
-// ht_sensor.enable();
+ acc_gyro.enable_x();
+#ifdef MINI_CRADLE
+ ht_sensor.init(NULL);
+ ht_sensor.enable();
+#endif
pt_sensor.enable();
uint8_t id22=0, idLSM6=0, id303mag=0, id303acc=0, id221;
@@ -963,9 +977,12 @@
acc_gyro.read_id(&idLSM6);
magnetometer.read_id(&id303mag);
accelerometer.read_id(&id303acc);
-// ht_sensor.read_id(&id221);
-
+#ifdef MINI_CRADLE
+ ht_sensor.read_id(&id221);
+ printf("LS303acc ID %x LS303mag ID %x LSM6DSL ID %x LPS22HB ID %x HTS221 ID %x\r\n", id303acc, id303mag, idLSM6, id22, id221);
+#else
printf("LS303acc ID %x LS303mag ID %x LSM6DSL ID %x LPS22HB ID %x \r\n", id303acc, id303mag, idLSM6, id22/*, id221*/);
+#endif
printf("\r\n");
p_customsensorservice = new CustomSensorService(*p_BLEdev);