Wim Huiskamp

Activity

Question gps module em 406 marked as solved by answer: You have reversed tx and rx. Try GPS gps(p28,p27) instead.
Wim Huiskamp - 29 Aug 2014
Answer posted for Question: Ethernet urgent Help! - You may want to verify yourself, but here are 2 from my notes that seem …
Wim Huiskamp - 28 Aug 2014
Question p20 definition error on k64f marked as solved by answer: Josh, not sure that I understand your problem. Are you referring to the example code …
Wim Huiskamp - 28 Aug 2014
Answer posted for Question: how can I make use of the analog buttons of LCD Shield on the Nucleoboard? - The analog inputs are typically not 5V tolerant. I would modify the board a bit …
Wim Huiskamp - 27 Aug 2014
Answer posted for Question: I2C to control tiny with EA LPC4088 - You seem to send two commands 0x00 before starting to receive. That causes problems when …
Wim Huiskamp - 27 Aug 2014
Reply to -
Wim Huiskamp - 24 Aug 2014
Answer posted for Question: Using CMSIS DAP interface to program multiple targets without a PC? - The current mbed CMSIS-DAP interfaces are SWD programmers without local memory. The original LPC1768 mbeds …
Wim Huiskamp - 20 Aug 2014
Answer posted for Question: Buffering of the RTC does not function - What is your code doing before it enters the while loop? Are you reinitialising the …
Wim Huiskamp - 20 Aug 2014
Question mbed HDK marked as solved by answer: The CMSIS-DAP interface does not have a local filesystem like the original mbed modules. So …
Wim Huiskamp - 11 Aug 2014
Reply to Editing answers broken - Still broken. Come on guys, why does it take forever to get this fixed...
Wim Huiskamp - 10 Aug 2014
Question Coming from Arduino with NXP LXPXpresso board: What debugger to use marked as solved by answer: The mbed/lpcxpresso 1549 already has an onboard programmer. You dont need a separate device. Full …
Wim Huiskamp - 24 Jul 2014
Answer posted for Question: how - When you find published code or libraries on the mbed website it will usually have …
Wim Huiskamp - 24 Jul 2014
Answer posted for Question: Vin range for mbed LPC1768 - The main issue is not the reverse voltage but the maximum dissipation. The regulators can …
Wim Huiskamp - 23 Jul 2014
Answer posted for Question: Newbie question about nRF51822 and ST LED Driver - The STP16CPC26 can be connected using SPI as follows: -MOSI to SDI -SCLK to CLK …
Wim Huiskamp - 22 Jul 2014
Answer posted for Question: Replacement? - If you check ebay there are still plenty of them around. http://www.ebay.nl/sch/i.html?_odkw=SAA1064&_osacat=0&_from=R40&_trksid=p2045573.m570.l1313&_nkw=SAA1064&_sacat=0 There are also …
Wim Huiskamp - 18 Jul 2014
Answer posted for Question: Is there is way to Check out the voltage that supplied on the mbed board or Application board? - You can use an [[https://mbed.org/handbook/AnalogIn | Analog input]] to check the voltage. The function can …
Wim Huiskamp - 18 Jul 2014
Question marked as solved by answer:
Wim Huiskamp - 17 Jul 2014
Answer posted for Question: ST Nucleo F411RE - The driver could not be installed. No mbed Microcontrollers were found. - The mbedwinserial driver is not needed for the nucleos and wont install anyhow without connecting …
Wim Huiskamp - 16 Jul 2014
Answer posted for Question: How to build toolchains? - You may want to look at CooCox. http://www.coocox.org/CooCox_CoIDE.htm. Your platforms are supported. There is also …
Wim Huiskamp - 16 Jul 2014
Question How driving LED on an other board ? marked as solved by answer: Pinnames should be declared as P3_25 rather than p3_25. Make sure you have series resistors …
Wim Huiskamp - 16 Jul 2014