Wim Huiskamp

Activity

Answer posted for Question: UART baud rate - You can declare two Serial ports and by selecting the right pins make sure they …
Wim Huiskamp - 11 May 2014
Answer posted for Question: ILI9341 STM32F103RB Nucleo compilation error - The warning can be ignored, the program will still run. The problem can be solved …
Wim Huiskamp - 11 May 2014
Answer posted for Question: How to avoid multiple copies of a const in binary file? - Libraries are independent pieces of code that are compiled separately and therefore they reserve space …
Wim Huiskamp - 09 May 2014
Answer posted for Question: I2C issue with Nucleo 152RE - You may need external pull-up R's on the I2C lines. They should be configured as …
Wim Huiskamp - 09 May 2014
Answer posted for Question: Power on Vin - According to the schematics (http://www.seeedstudio.com/wiki/images/6/6c/Arch_Pro_V1.0_Schematic.pdf), nothing is connected to Vin. You cant power the board …
Wim Huiskamp - 09 May 2014
Answer posted for Question: Best way to generate a pure sine wave - If you really need a pure sine than maybe an analogue voltage controlled oscillator is …
Wim Huiskamp - 07 May 2014
Answer posted for Question: RS485 with st Nucleo, not sand any data - D0/D1 are normally disabled since they are used for the serial connection to the host …
Wim Huiskamp - 07 May 2014
Answer posted for Question: CAN library - The [[https://mbed.org/handbook/CAN | handbook page]] should provide the information that you need.
Wim Huiskamp - 30 Apr 2014
Notebook page update: M24SR64 NFC/RFID Tag with I2C Interface
Wim Huiskamp - 27 Apr 2014
Reply to Ethernet (MAC) address? - William, you say you dont have a usb-serial connection for debugging, but in another thread …
Wim Huiskamp - 24 Apr 2014
Pull Request on SPI_TFT_ILI9341 updated: Added some methods and features
Wim Huiskamp - 22 Apr 2014
New fork of library: SPI_TFT_ILI9341 - Added methods and features
Wim Huiskamp - 22 Apr 2014
Answer posted for Question: OSC clock - In principle you can find out what the clock is by using the following code: …
Wim Huiskamp - 22 Apr 2014
Reply to Ethernet (MAC) address? - Hi William, the extern code should be outside/before the main. However, I am not sure …
Wim Huiskamp - 22 Apr 2014
Reply to mbed lib 80 ok, lib 81, 82 hangs - where can I get the source of each to compare? - The libs in this version range introduced a problem with digital pins that are declared …
Wim Huiskamp - 18 Apr 2014
Reply to Ethernet (MAC) address? - You dont need the mbed interface chip nor its flash mem as long as there …
Wim Huiskamp - 17 Apr 2014
Answer posted for Question: Overrun errors with two USART interrupts - Could be that your interrupt gets blocked or overruled by another higher level interrupt. Could …
Wim Huiskamp - 15 Apr 2014
Answer posted for Question: CAN interface on LPC1549 - The datasheet says that the LPC1549 supports CAN. However, CAN is currently not yet implemented …
Wim Huiskamp - 15 Apr 2014
Reply to Problems using a FRDM-25KLZ to program a MKL25Z128VFM4 - I think the oscillator should probably be running even when it is not yet used …
Wim Huiskamp - 14 Apr 2014
Answer posted for Question: Problem installing STLINK v2 usb driver (nucleo STM32F401) - Did you install both the new firmware on the board as well as the stlink …
Wim Huiskamp - 13 Apr 2014