Shivanand Gowda
Serial Peripheral Interface (SPI) Serial Single IO NOR Flash Memory Interfacing 1Gb
Fork of
S25FL256S
by 
Shivanand Gowda
Diff: S25FL256S.h
- Revision:
- 4:8c463abb67d5
- Child:
- 5:c2707c92ecb5
diff -r 6e3c0b23dc6e -r 8c463abb67d5 S25FL256S.h
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/S25FL256S.h Sat May 19 09:56:14 2018 +0000
@@ -0,0 +1,144 @@
+// S25FL256S.h
+
+#ifndef S25FL256S_H
+#define S25FL256S_H
+
+#include "mbed.h"
+#include <string>
+
+#define SPI_FREQ 5000000 //Change SPI Frequency Here
+#define SPI_MODE 0 // SPI Mode can be 0 or 3 . see data sheet
+#define SPI_NBIT 8 // Number of bits 8.
+
+
+
+#define DUMMY_ADDR 0x00
+#define WAIT_TIME 1
+
+#define ADDR_BMASK3 0xff000000
+#define ADDR_BMASK2 0x00ff0000
+#define ADDR_BMASK1 0x0000ff00
+#define ADDR_BMASK0 0x000000ff
+
+#define ADDR_BSHIFT3 24
+#define ADDR_BSHIFT2 16
+#define ADDR_BSHIFT1 8
+#define ADDR_BSHIFT0 0
+
+#define RDSR1 0x05 // 6th bit P_ERR Program Error-->1, NO error 0
+ //5th bit E_ERR Program Error-->1, No ERROR 0
+ //0th WIP --> 1 indicates Busy Writing, 0--> Free, Done
+ // read Bits 6,5,0
+#define READ_ID 0x90 // Read Electronic Manufacturer Signature
+#define RDID 0x9F //Read ID (JEDEC Manufacturer ID and JEDEC CFI)
+#define RES 0xAB // Read Electronic Signature
+
+//4 Byte Address4PP 12h)
+
+#define FOUR_FAST_READ 0x0C //Read Fast (4-byte Address) 0C
+#define FOUR_READ 0x13 //Read (4-byte Address)
+#define FOUR_DOR 0x3C //Read Dual Out (FOUR_-byte Address) 3C
+#define FOUR_QOR 0x6C //Read Quad Out (FOUR_-byte Address)
+#define FOUR_DIOR 0xBC // Dual I/O Read (FOUR_-byte Address) BC
+#define FOUR_QIOR 0xEC //FOUR_QIOR Quad I/O Read (FOUR_-byte Address) EC
+#define FOUR_DDRFR 0x0E //Read DDR Fast (FOUR_-byte Address)
+#define FOUR_DDRDIOR 0xBE // DDR Dual I/O Read (FOUR_-byte Address) BE
+#define FOUR_DDRQIOR 0xEE
+#define FOUR_PP 0x12 // FOUR_PP Page Program (FOUR_-byte Address) 12
+#define FOUR_QPP 0x34 //Quad Page Program (FOUR_-byte Address)
+#define FOUR_P4E 0x21 // Parameter 4-kB Erase (4-byte Address) 21
+#define FOUR_SE 0xDC // Erase 64/256 kB (4-byte Address) DC
+
+//3 Byte Address
+
+#define READ 0x03 //READ Read (3-byte Address) 03
+#define FAST_READ 0x0B //FAST_READ Read Fast (3-byte Address) 0B
+#define DOR 0x3B //DOR Read Dual Out (3-byte Address) 3B
+#define Q0R 0x6B //QOR Read Quad Out (3-byte Address) 6B
+#define DIOR 0xBB //DIOR Dual I/O Read (3-byte Address) BB
+#define QIOR 0xEB //QIOR Quad I/O Read (3-byte Address) EB
+#define DDRFR 0x0D //DDRFR Read DDR Fast (3-byte Address) 0D
+#define DDRDIOR 0xBD //DDRDIOR DDR Dual I/O Read (3-byte Address) BD
+#define DDRQIOR 0xED //DDRQIOR DDR Quad I/O Read (3-byte Address) ED
+#define PP 0x02 //PP Page Program (3-byte Address) 02
+#define Qpp 0x32 //QPP Quad Page Program (3-byte Address) 32
+#define P4E 0x20 //P4E Parameter 4-kB Erase (3-byte Address) 20
+#define SE 0xD8 //SE Erase 64 / 256 kB (3-byte Address) D8
+#define BE 0x60 // Erase Entire Chip.
+
+#define RDSR1 0x05 //RDSR1 Read Status Register-1 05
+#define RDSR2 0x07 //RDSR2 Read Status Register-2 07
+#define RDCR 0x35 //RDCR Read Configuration Register-1 35
+#define WRR 0x01 //Write Register (Status-1, Configuration-1)
+#define WRDI 0x04 //Write Disable 04
+#define WREN 0x06 //WREN Write Enable 06
+#define CLSR 0x30 //CLSR Clear Status Register-1 - Erase/Prog. Fail Reset 30
+#define ECCRD 0x18 //ECCRD ECC Read (4-byte address) 18
+#define ABRD 0x14 //ABRD AutoBoot Register Read 14
+#define ABWR 0x15 //AutoBoot Register Write 15
+#define BRRD 0x16 //Bank Register Read 16
+#define BRWR 0x17 //Bank Register Write 17
+#define BRAC 0xB9 //BRAC Bank Register Access (Legacy Command formerly used for Deep Power Down) B9
+#define DLPRD 0x41 //DLPRD Data Learning Pattern Read 41
+#define PNVDLR 0x43 //PNVDLR Program NV Data Learning Register 43
+#define WVDLR 0x4A //Write Volatile Data Learning Register 4A
+#define PGSP 0x85 //Program Suspend 85
+#define PGRS 0x8A //Program Resume 8A
+#define ERSP 0x75 //Erase Suspend 75
+#define ERRS 0x7A //Erase Resume 7A
+#define OTPP 0x42 //OTP Program 42
+#define OTPR 0x4B //OTP Read 4B
+
+//Advanced Sector Protection
+
+#define DYBRD 0xE0 //DYB Read E0 133
+#define DYBWR 0xE1 //DYB Write E1 133
+#define PPBRD 0xE2 //PPB Read E2 133
+#define PPBP 0xE3 //PPB Program E3 133
+#define PPBE 0xE4 //PPB Erase E4 133
+#define ASPRD 0x2B //ASP Read 2B 133
+#define ASPP 0x2F //ASP Program 2F 133
+#define PLBRD 0xA7 //PPB Lock Bit Read A7 133
+#define PLBWR 0xA6 //PPB Lock Bit Write A6 133
+#define PASSRD 0xE7 //Password Read E7 133
+#define PASSP 0xE8 //Password Program E8 133
+#define PASSU 0xE9 //Password Unlock E9 133
+#define DUMMY 0x00 // Dummy write to read
+//Reset
+
+#define RESET 0xF0 //Software Reset F0 133
+#define MBR 0xFF //Mode Bit Reset FF 133
+#define DUMMYBYTE 0x00 //Dummy byte for Read Operation
+
+class S25FL256S: public SPI {
+public:
+ S25FL256S(PinName mosi, PinName miso, PinName sclk, PinName cs);
+
+ int readByte(int addr); // takes a 32-bit (4 bytes) address and returns the data (1 byte) at that location
+ void readStream(int addr, char* buf, int count); // takes a 32-bit address, reads count bytes, and stores results in buf
+
+ void writeByte(int addr, int data); // takes a 32-bit (4 bytes) address and a byte of data to write at that location
+ void writeStream(int addr, char* buf, int count); // write count bytes of data from buf to memory, starting at addr
+ void writeString(int add, string str);
+ void sectorErase(int addr);
+ void chipErase(); //erase all data on chip
+ uint8_t readRegister();
+ uint8_t checkIfBusy(); // Check if IC is bury writing or erasing
+ void writeRegister(uint8_t regValue); //Write status register or configuration register
+ void reset(void); // Reset Chip
+ void clearRegister(); // Clear Status Register
+ void Read_Identification(uint8_t *buf);
+ long raedLong(int address); // Read long int number
+ void writeLong(int addr, long value); // Write Long Integer Number
+private:
+ void writeEnable(); // write enable
+ void writeDisable(); // write disable
+ void chipEnable(); // chip enable
+ void chipDisable();
+ // chip disable
+
+ // SPI _spi;
+ DigitalOut _cs;
+};
+
+#endif
\ No newline at end of file