james kain / Mbed 2 deprecated GPS_Incremental

JEK changes enabling proper recording of IMU/GPS datastrams - 02-APR-2013

Dependencies:   mbed

Fork of GPS_Incremental by Dan Matthews

ADIS16488.h@4:68268737ff89, 2013-03-29 (annotated)

Committer:
jekain314
Date:
Fri Mar 29 20:52:24 2013 +0000
Revision:
4:68268737ff89
Parent:
0:c746ee34feae
Child:
6:2a8486283198
from Jim's site - March 29th,2013

Who changed what in which revision?

UserRevisionLine numberNew contents of line
dannyman939 0:c746ee34feae 1
dannyman939 0:c746ee34feae 2
dannyman939 0:c746ee34feae 3
dannyman939 0:c746ee34feae 4 //set up the SPI on pins 5, 6, 7 to read from the ADIS16488
dannyman939 0:c746ee34feae 5 SPI spi(p5, p6, p7); // mosi (DIN), miso (DOUT), sclk (CLK)
dannyman939 0:c746ee34feae 6 DigitalOut ADIS_CS(p8); //Chip Select for the ADIS SPI
dannyman939 0:c746ee34feae 7 InterruptIn ADIS_DR(p28); //DataReady interrupt connected to DIO2 for ADIS
dannyman939 0:c746ee34feae 8 DigitalOut ADIS_RST(p20); //ADIS reset pin
dannyman939 0:c746ee34feae 9
dannyman939 0:c746ee34feae 10 bool IMUDataReady = false;
dannyman939 0:c746ee34feae 11 int IMURecordCounter = 0;
dannyman939 0:c746ee34feae 12 //see Table 9 from page 11 of the ADIS16488 spec
dannyman939 0:c746ee34feae 13 //see fig 15 of spec -- note the low byte of the regsiter word is always zero
dannyman939 0:c746ee34feae 14 // X_DELTANG_LOW, Y_DELTANG_LOW, X_DETANG_LOW, X_DELTVEL_LOW, Y_DELTVEL_LOW, Z_DELTVEL_LOW
dannyman939 0:c746ee34feae 15 unsigned short LOW_REGISTER[] = {0x4000, 0x4400, 0x4800, 0x4C00, 0x5000, 0x5400};
dannyman939 0:c746ee34feae 16 // X_DELTANG_HIGH, Y_DELTANG_HIGH, X_DETANG_HIGH, X_DELTVEL_HIGH, Y_DELTVEL_HIGH, Z_DELTVEL_HIGH
dannyman939 0:c746ee34feae 17 unsigned short HIGH_REGISTER[] = {0x4200, 0x4600, 0x4A00, 0x4E00, 0x5200, 0x5600};
dannyman939 0:c746ee34feae 18
dannyman939 0:c746ee34feae 19 union WD { long dataWord; unsigned short pt[2];} wd;
dannyman939 0:c746ee34feae 20
dannyman939 0:c746ee34feae 21 #pragma pack(1)
dannyman939 0:c746ee34feae 22 struct IMUREC
dannyman939 0:c746ee34feae 23 {
dannyman939 0:c746ee34feae 24 unsigned long synch;
dannyman939 0:c746ee34feae 25 unsigned char msgID;
dannyman939 0:c746ee34feae 26 double GPSTime;
dannyman939 0:c746ee34feae 27 long dataWord[6];
dannyman939 0:c746ee34feae 28 } imuRec;
dannyman939 0:c746ee34feae 29
dannyman939 0:c746ee34feae 30
dannyman939 0:c746ee34feae 31
dannyman939 0:c746ee34feae 32 void IMUDataReadyISR(void)
dannyman939 0:c746ee34feae 33 {
jekain314 4:68268737ff89 34 IMUDataReady = true;
dannyman939 0:c746ee34feae 35 return;
dannyman939 0:c746ee34feae 36 }
dannyman939 0:c746ee34feae 37
dannyman939 0:c746ee34feae 38 void setupADIS(void)
dannyman939 0:c746ee34feae 39 {
dannyman939 0:c746ee34feae 40 ADIS_DR.mode(PullDown);
dannyman939 0:c746ee34feae 41 ADIS_RST = 0;
dannyman939 0:c746ee34feae 42
dannyman939 0:c746ee34feae 43 printf("\nStart of ADIS test\n");
dannyman939 0:c746ee34feae 44 // set the IMU dataReady ISR
dannyman939 0:c746ee34feae 45 ADIS_DR.rise(&IMUDataReadyISR);
dannyman939 0:c746ee34feae 46
dannyman939 0:c746ee34feae 47 // Setup the mbed SPI for 16 bit data, high steady state clock,
dannyman939 0:c746ee34feae 48 // second edge capture, with a 1MHz clock rate
dannyman939 0:c746ee34feae 49 spi.format(16,3);
dannyman939 0:c746ee34feae 50 spi.frequency(1000000);
dannyman939 0:c746ee34feae 51
dannyman939 0:c746ee34feae 52 ADIS_CS = 1; //CS must be set high before it goes low cause the enable is the transition
dannyman939 0:c746ee34feae 53 ADIS_RST = 1;
dannyman939 0:c746ee34feae 54 wait(0.5);
dannyman939 0:c746ee34feae 55 ADIS_CS = 0; //set the Chip select low to enable the IMU SPI access
dannyman939 0:c746ee34feae 56
dannyman939 0:c746ee34feae 57 spi.write((int)0x8003); //change to page 3
dannyman939 0:c746ee34feae 58
dannyman939 0:c746ee34feae 59 //change the DECRATE to 98.4 Hz (this is also in page 3)
dannyman939 0:c746ee34feae 60 //the 8 sets the high bit to 1 indicating a write to a register
dannyman939 0:c746ee34feae 61 // The C abd D designate the registers for the DECRATE of Page 3
dannyman939 0:c746ee34feae 62 // The 17 sets the rate to: 2460/(23+1) = 102.5Hz
dannyman939 0:c746ee34feae 63 spi.write((int)0x8C17); //write high byte (only page number can be written in a single byte)
dannyman939 0:c746ee34feae 64 spi.write((int)0x8D00); //write the low byte of DECRATE
dannyman939 0:c746ee34feae 65
dannyman939 0:c746ee34feae 66 //to set the GPS VARF clock as the input synch clock for the IMU
dannyman939 0:c746ee34feae 67 //the high byte is CD indicating the synch is enabled on the rising edge of the input clock
dannyman939 0:c746ee34feae 68 //spi.write((int)0x86CD); //write high byte to register 0x06
dannyman939 0:c746ee34feae 69 //spi.write((int)0x8700); //write the low byte of 00 to registed 0x07
dannyman939 0:c746ee34feae 70
dannyman939 0:c746ee34feae 71 //change the page to 0 to get the data
dannyman939 0:c746ee34feae 72 spi.write((int)0x8000); //change to page 0
dannyman939 0:c746ee34feae 73
dannyman939 0:c746ee34feae 74 //set the IMU synch and message ID
dannyman939 0:c746ee34feae 75 imuRec.synch = 0xAA44121C; //same as the GPS synch words
dannyman939 0:c746ee34feae 76 imuRec.msgID=111; //IMU record ID
dannyman939 0:c746ee34feae 77 }