File content as of revision 11:084e8ba240c1:

/*CODED by Qiyong Mu on 21/06/2014
kylongmu@msn.com
*/


#ifndef mpu9250_h
#define mpu9250_h
#include "mbed.h"


class mpu9250_spi
{
    SPI& spi;
    DigitalOut cs;
    
  public:
    mpu9250_spi(SPI& _spi, PinName _cs);
    unsigned int WriteReg( uint8_t WriteAddr, uint8_t WriteData );
    unsigned int ReadReg( uint8_t WriteAddr, uint8_t WriteData );
    void ReadRegs( uint8_t ReadAddr, uint8_t *ReadBuf, unsigned int Bytes );

    bool init(int sample_rate_div,int low_pass_filter);
    void read_temp();
    void read_acc();
    void read_rot();
    unsigned int set_gyro_scale(int scale);
    unsigned int set_acc_scale(int scale);
    void calib_acc();
    void AK8963_calib_Magnetometer();
    void select();
    void deselect();
    unsigned int whoami();
    uint8_t  AK8963_whoami();
    void AK8963_read_Magnetometer();
    void read_all();


    
    float acc_divider;
    float gyro_divider;
    
    int calib_data[3];
    float Magnetometer_ASA[3];

    float accelerometer_data[3];
    float Temperature;
    float gyroscope_data[3];
    float Magnetometer[3];
    
  private:
    PinName _CS_pin;
    PinName _SO_pin;
    PinName _SCK_pin;
    float _error;
};

#endif



// mpu9250 registers
#define MPUREG_XG_OFFS_TC 0x00
#define MPUREG_YG_OFFS_TC 0x01
#define MPUREG_ZG_OFFS_TC 0x02
#define MPUREG_X_FINE_GAIN 0x03
#define MPUREG_Y_FINE_GAIN 0x04
#define MPUREG_Z_FINE_GAIN 0x05
#define MPUREG_XA_OFFS_H 0x06
#define MPUREG_XA_OFFS_L 0x07
#define MPUREG_YA_OFFS_H 0x08
#define MPUREG_YA_OFFS_L 0x09
#define MPUREG_ZA_OFFS_H 0x0A
#define MPUREG_ZA_OFFS_L 0x0B
#define MPUREG_PRODUCT_ID 0x0C
#define MPUREG_SELF_TEST_X 0x0D
#define MPUREG_SELF_TEST_Y 0x0E
#define MPUREG_SELF_TEST_Z 0x0F
#define MPUREG_SELF_TEST_A 0x10
#define MPUREG_XG_OFFS_USRH 0x13
#define MPUREG_XG_OFFS_USRL 0x14
#define MPUREG_YG_OFFS_USRH 0x15
#define MPUREG_YG_OFFS_USRL 0x16
#define MPUREG_ZG_OFFS_USRH 0x17
#define MPUREG_ZG_OFFS_USRL 0x18
#define MPUREG_SMPLRT_DIV 0x19
#define MPUREG_CONFIG 0x1A
#define MPUREG_GYRO_CONFIG 0x1B
#define MPUREG_ACCEL_CONFIG 0x1C
#define MPUREG_ACCEL_CONFIG_2      0x1D
#define MPUREG_LP_ACCEL_ODR        0x1E
#define MPUREG_MOT_THR             0x1F
#define MPUREG_FIFO_EN             0x23
#define MPUREG_I2C_MST_CTRL        0x24
#define MPUREG_I2C_SLV0_ADDR       0x25
#define MPUREG_I2C_SLV0_REG        0x26
#define MPUREG_I2C_SLV0_CTRL       0x27
#define MPUREG_I2C_SLV1_ADDR       0x28
#define MPUREG_I2C_SLV1_REG        0x29
#define MPUREG_I2C_SLV1_CTRL       0x2A
#define MPUREG_I2C_SLV2_ADDR       0x2B
#define MPUREG_I2C_SLV2_REG        0x2C
#define MPUREG_I2C_SLV2_CTRL       0x2D
#define MPUREG_I2C_SLV3_ADDR       0x2E
#define MPUREG_I2C_SLV3_REG        0x2F
#define MPUREG_I2C_SLV3_CTRL       0x30
#define MPUREG_I2C_SLV4_ADDR       0x31
#define MPUREG_I2C_SLV4_REG        0x32
#define MPUREG_I2C_SLV4_DO         0x33
#define MPUREG_I2C_SLV4_CTRL       0x34
#define MPUREG_I2C_SLV4_DI         0x35
#define MPUREG_I2C_MST_STATUS      0x36
#define MPUREG_INT_PIN_CFG 0x37
#define MPUREG_INT_ENABLE 0x38
#define MPUREG_ACCEL_XOUT_H 0x3B
#define MPUREG_ACCEL_XOUT_L 0x3C
#define MPUREG_ACCEL_YOUT_H 0x3D
#define MPUREG_ACCEL_YOUT_L 0x3E
#define MPUREG_ACCEL_ZOUT_H 0x3F
#define MPUREG_ACCEL_ZOUT_L 0x40
#define MPUREG_TEMP_OUT_H 0x41
#define MPUREG_TEMP_OUT_L 0x42
#define MPUREG_GYRO_XOUT_H 0x43
#define MPUREG_GYRO_XOUT_L 0x44
#define MPUREG_GYRO_YOUT_H 0x45
#define MPUREG_GYRO_YOUT_L 0x46
#define MPUREG_GYRO_ZOUT_H 0x47
#define MPUREG_GYRO_ZOUT_L 0x48
#define MPUREG_EXT_SENS_DATA_00    0x49
#define MPUREG_EXT_SENS_DATA_01    0x4A
#define MPUREG_EXT_SENS_DATA_02    0x4B
#define MPUREG_EXT_SENS_DATA_03    0x4C
#define MPUREG_EXT_SENS_DATA_04    0x4D
#define MPUREG_EXT_SENS_DATA_05    0x4E
#define MPUREG_EXT_SENS_DATA_06    0x4F
#define MPUREG_EXT_SENS_DATA_07    0x50
#define MPUREG_EXT_SENS_DATA_08    0x51
#define MPUREG_EXT_SENS_DATA_09    0x52
#define MPUREG_EXT_SENS_DATA_10    0x53
#define MPUREG_EXT_SENS_DATA_11    0x54
#define MPUREG_EXT_SENS_DATA_12    0x55
#define MPUREG_EXT_SENS_DATA_13    0x56
#define MPUREG_EXT_SENS_DATA_14    0x57
#define MPUREG_EXT_SENS_DATA_15    0x58
#define MPUREG_EXT_SENS_DATA_16    0x59
#define MPUREG_EXT_SENS_DATA_17    0x5A
#define MPUREG_EXT_SENS_DATA_18    0x5B
#define MPUREG_EXT_SENS_DATA_19    0x5C
#define MPUREG_EXT_SENS_DATA_20    0x5D
#define MPUREG_EXT_SENS_DATA_21    0x5E
#define MPUREG_EXT_SENS_DATA_22    0x5F
#define MPUREG_EXT_SENS_DATA_23    0x60
#define MPUREG_I2C_SLV0_DO         0x63
#define MPUREG_I2C_SLV1_DO         0x64
#define MPUREG_I2C_SLV2_DO         0x65
#define MPUREG_I2C_SLV3_DO         0x66
#define MPUREG_I2C_MST_DELAY_CTRL  0x67
#define MPUREG_SIGNAL_PATH_RESET   0x68
#define MPUREG_MOT_DETECT_CTRL     0x69
#define MPUREG_USER_CTRL 0x6A
#define MPUREG_PWR_MGMT_1 0x6B
#define MPUREG_PWR_MGMT_2 0x6C
#define MPUREG_BANK_SEL 0x6D
#define MPUREG_MEM_START_ADDR 0x6E
#define MPUREG_MEM_R_W 0x6F
#define MPUREG_DMP_CFG_1 0x70
#define MPUREG_DMP_CFG_2 0x71
#define MPUREG_FIFO_COUNTH 0x72
#define MPUREG_FIFO_COUNTL 0x73
#define MPUREG_FIFO_R_W 0x74
#define MPUREG_WHOAMI 0x75
#define MPUREG_XA_OFFSET_H         0x77
#define MPUREG_XA_OFFSET_L         0x78
#define MPUREG_YA_OFFSET_H         0x7A
#define MPUREG_YA_OFFSET_L         0x7B
#define MPUREG_ZA_OFFSET_H         0x7D
#define MPUREG_ZA_OFFSET_L         0x7E
/* ---- AK8963 Reg In MPU9250 ----------------------------------------------- */

#define AK8963_I2C_ADDR             0x0c//0x18
#define AK8963_Device_ID            0x48

// Read-only Reg
#define AK8963_WIA                  0x00
#define AK8963_INFO                 0x01
#define AK8963_ST1                  0x02
#define AK8963_HXL                  0x03
#define AK8963_HXH                  0x04
#define AK8963_HYL                  0x05
#define AK8963_HYH                  0x06
#define AK8963_HZL                  0x07
#define AK8963_HZH                  0x08
#define AK8963_ST2                  0x09
// Write/Read Reg
#define AK8963_CNTL1                0x0A
#define AK8963_CNTL2                0x0B
#define AK8963_ASTC                 0x0C
#define AK8963_TS1                  0x0D
#define AK8963_TS2                  0x0E
#define AK8963_I2CDIS               0x0F
// Read-only Reg ( ROM )
#define AK8963_ASAX                 0x10
#define AK8963_ASAY                 0x11
#define AK8963_ASAZ                 0x12

// Configuration bits mpu9250
#define BIT_SLEEP 0x40
#define BIT_H_RESET 0x80
#define BITS_CLKSEL 0x07
#define MPU_CLK_SEL_PLLGYROX 0x01
#define MPU_CLK_SEL_PLLGYROZ 0x03
#define MPU_EXT_SYNC_GYROX 0x02
#define BITS_FS_250DPS              0x00
#define BITS_FS_500DPS              0x08
#define BITS_FS_1000DPS             0x10
#define BITS_FS_2000DPS             0x18
#define BITS_FS_2G                  0x00
#define BITS_FS_4G                  0x08
#define BITS_FS_8G                  0x10
#define BITS_FS_16G                 0x18
#define BITS_FS_MASK                0x18
#define BITS_DLPF_CFG_256HZ_NOLPF2  0x00
#define BITS_DLPF_CFG_188HZ         0x01
#define BITS_DLPF_CFG_98HZ          0x02
#define BITS_DLPF_CFG_42HZ          0x03
#define BITS_DLPF_CFG_20HZ          0x04
#define BITS_DLPF_CFG_10HZ          0x05
#define BITS_DLPF_CFG_5HZ           0x06
#define BITS_DLPF_CFG_2100HZ_NOLPF  0x07
#define BITS_DLPF_CFG_MASK          0x07
#define BIT_INT_ANYRD_2CLEAR        0x10
#define BIT_RAW_RDY_EN              0x01
#define BIT_I2C_IF_DIS              0x10

#define READ_FLAG   0x80

/* ---- Sensitivity --------------------------------------------------------- */

#define MPU9250A_2g       ((float)0.000061035156f) // 0.000061035156 g/LSB
#define MPU9250A_4g       ((float)0.000122070312f) // 0.000122070312 g/LSB
#define MPU9250A_8g       ((float)0.000244140625f) // 0.000244140625 g/LSB
#define MPU9250A_16g      ((float)0.000488281250f) // 0.000488281250 g/LSB

#define MPU9250G_250dps   ((float)0.007633587786f) // 0.007633587786 dps/LSB
#define MPU9250G_500dps   ((float)0.015267175572f) // 0.015267175572 dps/LSB
#define MPU9250G_1000dps  ((float)0.030487804878f) // 0.030487804878 dps/LSB
#define MPU9250G_2000dps  ((float)0.060975609756f) // 0.060975609756 dps/LSB

#define MPU9250M_4800uT   ((float)0.6f)            // 0.6 uT/LSB

#define MPU9250T_85degC   ((float)0.002995177763f) // 0.002995177763 degC/LSB

#define     Magnetometer_Sensitivity_Scale_Factor ((float)0.15f)