David Giles
/
CM-MBED_RSEDP_Test_Suite_LPC1768_V3
This is a complete listing of the RS-EDP software for the mbed module to support the RS-EDP platform.
Diff: HeaderFiles/RSEDP_Slave_Address_Defines.h
- Revision:
- 0:5b7639d1f2c4
diff -r 000000000000 -r 5b7639d1f2c4 HeaderFiles/RSEDP_Slave_Address_Defines.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/HeaderFiles/RSEDP_Slave_Address_Defines.h Fri Nov 19 09:49:16 2010 +0000 @@ -0,0 +1,58 @@ +/* Slave Address Header File */ + + + +#define MICROCHIP_MOTOR_DRIVER_BASE 0x40 + /* Microchip Twin Motor Drive Module RD-EDP-AM-MC2 */ + /* 0x40 - 7 bit */ + /* Range is 0x40 - 0x47 as there may be 4 modules per base board */ + /* This device is used to define the Microchip dsPIC33FJ128MC804 I2C Slave Address */ + /* Upto 6 dsPIC devices can be populated (3 modules) on the motor drive board */ + /* Therefore the 7 bit address range is 0x40 - 0x45 */ + /* The link options on the module provide additional Slave address information */ + +/* Defines the range of the dsPIC Slave Address's. The base address is configured above */ +/* As we can have up to 8 dsPICs in the system, we need to specify the range of address's */ +#define DSPIC_SLAVE_ADDRESS_MIN (MICROCHIP_MOTOR_DRIVER_BASE) /* min is 7 bit base of 112 */ +#define DSPIC_SLAVE_ADDRESS_MAX ((MICROCHIP_MOTOR_DRIVER_BASE) +7) /* max is 7 bit base of 112 plus the DIP switch/solder bridge settings on the PCB 0 - 7 */ + + +#define PCA9675_BASE_BOARD 0x20 // 0x20 - 7 bit + /* This device is on the base board and is a serial I/O latch connected to the DIP Switch */ + + +#define M24C32_BASE_BOARD 0x51 // 0x51 - 7 bit + /* This device is a serial EEPROM device which is connected to the base board */ + /* The actual slave address also has three low order bits to be added */ + /* These bits are b1,b2,b3 within the byte */ + /* These bits are derived from the external A0,A1 and A2 pins on the device */ + /* Therefore the slave address's are 0xa0, 0xa2, 0xa4,0xa6,0xa8,0xaa, 0xac,0xae */ + + +#define PCF8583_COMMS_MODULE 0x50 // 0x50 - 7 bit +/* The actual slave address also has three low order bits to be added */ +/* These bits are b1,b2,b3 within the byte*/ +/* These bits are derived from the external A0,A1 and A2 pins on the device */ +/* Therefore the slave address's are 0xa0, 0xa2, 0xa4,0xa6,0xa8,0xaa, 0xac,0xae */ + + + +#define PCA9555_DIGITAL_IO_OUT 0x23 // 0x23 - 7 bit + /* The actual slave address also has three low order bits to be added */ + /* These bits are a0,a1,a2 within the byte*/ + /* These bits are derived from the external A0,A1 and A2 pins on the device */ + /* Therefore the 7 bit slave address range is 0x20 to 0x27 */ + + +#define PCA9555_DIGITAL_IO_IN 0x22 // 0x22 - 7 bit + /* This is the hardware configured 0x22 7 bit Slave Address of this perihperal */ + + +#define MAX1X3X_ANALOGUE_ADC 0x65 // 0x65 - 7 bit + /* This is the slave address of the MAX1038 on the Analogue Module PCB */ + + +#define AD5263_ANALOGUE_DIGITAL_POT 0x2c // 0x2c - 7 bit + /* This is the slave address of the digtial Potentiometer, AD5263 on the anlogue module */ + +