Diff: HeaderFiles/RSEDP_Slave_Address_Defines.h

Revision:

0:5b7639d1f2c4

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/HeaderFiles/RSEDP_Slave_Address_Defines.h	Fri Nov 19 09:49:16 2010 +0000
@@ -0,0 +1,58 @@
+/* Slave Address Header File */
+
+
+
+#define MICROCHIP_MOTOR_DRIVER_BASE 0x40
+    /* Microchip Twin Motor Drive Module RD-EDP-AM-MC2 */
+	/* 0x40 - 7 bit */
+	/* Range is 0x40 - 0x47 as there may be 4 modules per base board */
+	/* This device is used to define the Microchip dsPIC33FJ128MC804 I2C Slave Address */
+	/* Upto 6 dsPIC devices can be populated (3 modules) on the motor drive board */
+	/* Therefore the 7 bit address range is 0x40 - 0x45 */
+	/* The link options on the module provide additional Slave address information */
+
+/* Defines the range of the dsPIC Slave Address's. The base address is configured above */
+/* As we can have up to 8 dsPICs in the system, we need to specify the range of address's */
+#define DSPIC_SLAVE_ADDRESS_MIN (MICROCHIP_MOTOR_DRIVER_BASE)					/* min is 7 bit base of 112 */
+#define DSPIC_SLAVE_ADDRESS_MAX ((MICROCHIP_MOTOR_DRIVER_BASE) +7)			    /* max is 7 bit base of 112 plus the DIP switch/solder bridge settings on the PCB 0 - 7 */
+
+
+#define PCA9675_BASE_BOARD 0x20                       // 0x20 - 7 bit
+    /* This device is on the base board and is a serial I/O latch connected to the DIP Switch */
+
+
+#define M24C32_BASE_BOARD 0x51                      // 0x51 - 7 bit
+    /* This device is a serial EEPROM device which is connected to the base board */
+    /* The actual slave address also has three low order bits to be added */
+    /* These bits are b1,b2,b3 within the byte */
+    /* These bits are derived from the external A0,A1 and A2 pins on the device */
+    /* Therefore the slave address's are 0xa0, 0xa2, 0xa4,0xa6,0xa8,0xaa, 0xac,0xae */
+
+
+#define PCF8583_COMMS_MODULE 0x50                // 0x50 - 7 bit                
+/* The actual slave address also has three low order bits to be added */
+/* These bits are b1,b2,b3 within the byte*/
+/* These bits are derived from the external A0,A1 and A2 pins on the device */
+/* Therefore the slave address's are 0xa0, 0xa2, 0xa4,0xa6,0xa8,0xaa, 0xac,0xae */
+
+
+
+#define PCA9555_DIGITAL_IO_OUT 0x23                 // 0x23 - 7 bit
+    /* The actual slave address also has three low order bits to be added */
+    /* These bits are a0,a1,a2 within the byte*/
+    /* These bits are derived from the external A0,A1 and A2 pins on the device */
+    /* Therefore the 7 bit slave address range is 0x20 to 0x27 */
+                                        
+
+#define PCA9555_DIGITAL_IO_IN 0x22                // 0x22 - 7 bit    
+    /* This is the hardware configured 0x22 7 bit Slave Address of this perihperal */
+
+
+#define MAX1X3X_ANALOGUE_ADC 0x65                // 0x65    - 7 bit
+    /* This is the slave address of the MAX1038 on the Analogue Module PCB */
+
+
+#define AD5263_ANALOGUE_DIGITAL_POT 0x2c        // 0x2c - 7 bit
+    /* This is the slave address of the digtial Potentiometer, AD5263 on the anlogue module */
+
+