File content as of revision 3:c2d1b0d432ad:

#ifndef MS5611_H
#define MS5611_H

#include "mbed.h"

/** Software routines to access the Measurement Specialties' MS5611-01BA03 
 *  Variometer Module using the I2C bus option.  The MS5611 is a 24 bit 
 *  temperature and pressure transducer for high accuracy Barometer and 
 *  Altimeter applications.  It also includes compensation coefficients
 *  stored within the device. 
 * 
 *  Code adapted from Measurement Specialties:
 *  "AN520 C-code example for MS56xx, MS57xx (except analog sensor), and 
 *  MS58xx series pressure sensors"
 *
 *  Note: AN520 has not been updated for use with the MS5611.  Changes
 *  were necessary to "calcPT()" in order to correct scaling of 
 *  pressure readings.
 * 
 *  Features:
 *          Altitude resolution to 10cm
 *          Fast conversion down to 1 ms
 *          Low power, 1 μA (standby < 0.15 μA)
 *          QFN package 5.0 x 3.0 x 1.0 mm^3
 *          Supply voltage 1.8 to 3.6 V
 *          Integrated digital pressure sensor (24 bit DeltaSigma ADC)
 *          Operating range: 10 to 1200 mbar, -40 to +85 °C
 *          I2C and SPI interface up to 20 MHz
 *          No external components (Internal oscillator)
 *          Excellent long term stability
 *
 * @code
 * #include "mbed.h"
 * #include "ms5611.h" 
 *
 * ms5611 ms(p9, p10);                        // i2c pins used
 * Serial pc(USBTX, USBRX);                   // local terminal interface
 *
 *
 * int main (void) {
 *     pc.baud(921600);                        // set up USB serial speed
 *     i2c.frequency(400000);                  // set up i2c speed
 *
 *     // set up the ms5611
 *     pc.printf("\n\nInitializing the MS5611..\n");
 *     ms.cmd_reset();
 *     pc.printf("Ready\n");
 *
 *     while(1) {
 *         double Temp = ms.calcTemp();
 *         double Press = ms.calcPressure();
 *         pc.printf("Temp: %.2f degC    Barometer: %.1f mB  %.3f in/Hg\n", Temp, Press, Press * 0.0295301);
 *         wait(2.0);
 *     }
 * }
 *
 * @endcode
 */
 
//_____ M A C R O S

#define MS5611_ADDR_W 0xEE // Module address write mode
#define MS5611_ADDR_R 0xEF // Module address read mode
#define MS5611_CMD_RESET 0x1E // ADC reset command
#define MS5611_CMD_ADC_READ 0x00 // ADC read command
#define MS5611_CMD_ADC_CONV 0x40 // ADC conversion command
#define MS5611_CMD_ADC_D1 0x00 // ADC D1 conversion
#define MS5611_CMD_ADC_D2 0x10 // ADC D2 conversion
#define MS5611_CMD_ADC_256 0x00 // ADC OSR=256
#define MS5611_CMD_ADC_512 0x02 // ADC OSR=512
#define MS5611_CMD_ADC_1024 0x04 // ADC OSR=1024
#define MS5611_CMD_ADC_2048 0x06 // ADC OSR=2048
#define MS5611_CMD_ADC_4096 0x08 // ADC OSR=4096
#define MS5611_CMD_PROM_RD 0xA0 // Prom read command

    /** Create ms5611 controller class
     *
     * @param ms5611 class
     *
     */
class ms5611 {

public:
    /** Create a MS5611 object using the specified I2C object
     *
     * @param constructor, - the I2C object to communicate with
     */
    ms5611(PinName sda, PinName scl);
    /** Initialize the MS5611 and set up the coefficients
     *    First - reset the MS5611
     *    Second - load coefficient values from the MS5611 PROM
     *    Third  - calculate coefficient checksum
     *  This routine only needs to be run once at boot up
     *
     * @param NONE
     */
    void cmd_reset();
    /** Calculate and return compensated temperature
     *    Returns double temperature in degC
     *
     * @param NONE
     */
    double calcTemp();
    /** Calculate and return compensated barometric pressure
     *    Returns double pressure in millibars
     *
     * @param NONE
     */
    double calcPressure();
    /** Return compensated barometric pressure
     *    Returns double pressure in millibars
     *    DOES NOT RE-CALCULATE FIRST!!!
     *    Saves time if you calcTemp(); first
     *
     * @param NONE
     */
    double getPressure();
    /** Calculate and returns altitude in feet
     *    Returns float altitude
     *
     * @param float pressure (mB) at sea level
     */
    float getAltitudeFT(float sea_pressure);
    
private:
    int m_i2c_start(bool readMode);
    void m_i2c_stop(void);
    unsigned char m_i2c_write(unsigned char data);
    unsigned char m_i2c_readAck(void);
    unsigned char m_i2c_readNak(void);
    void m_i2c_send(char cmd);
    void loadCoefs();
    unsigned long cmd_adc(char cmd);
    unsigned int cmd_prom(char coef_num);
    unsigned char crc4(unsigned  n_prom[]);
    void calcPT();
    unsigned int PTbuffer[8];       // calibration coefficients
  
protected:
    I2C     _i2c;
    

}; 
#endif