Diff: settings.txt

Revision:

60:899862db7f2a

Parent:

56:0d9684c7df36

Child:

82:ee6eed2a51bd

diff -r 10ab123d3c7c -r 899862db7f2a settings.txt
--- a/settings.txt	Mon Sep 13 07:39:09 2021 +0000
+++ b/settings.txt	Mon Sep 13 13:50:52 2021 +0000
@@ -4,8 +4,9 @@
  #   The system will instead transparently connect the USB COM port to the radio com port
  #   Both ports will be set to the baud rate specified.
  #   When used this option should be first in the options file.
+ --------------------------------
 //RadioConfigPassthrough=115200
- 
+--------------------------------
 
 [Serial Output Format]
 # Sets the serial output format.
@@ -50,17 +51,22 @@
 #Filter order must be set to enable filters.
 #Frequency default is 10Hz
 #Rate default is 100Hz
+
+--------------------------------
 //FilterOrder=1
 //FilterFreq=7
 //FilterRate=100
+--------------------------------
 
+# Enable channels to low pass filter. All filters use the settings given above.
+# A value of 1 enables the filter. A value of 0 or skipping the line disables the filter.
+--------------------------------
 //FilterXY=0
 //FilterZ=0
 //FilterRoll=0
 //FilterPitch=1
 //FilterYaw=0
-# Enable channels to low pass filter. All filters use the settings given above.
-# A value of 1 enables the filter. A value of 0 or skipping the line disables the filter.
+--------------------------------
 
 # NOTE-The filter will add latency so a filtered channel will be delayed relative to an unfiltered one.
  
@@ -71,9 +77,11 @@
 # Setting this option to 1 allows additional fields to be passed through the FIZ box.
 # Currently supported fields are:
 #   Used Beacon List (mask value 0x1000)
+--------------------------------
 //ExtendedOutput=1
+--------------------------------
 
-
+[Frame Delay]
 # By default the FIZ output is sent as soon as possible after the sync pulse.
 # An optional delay can be added to this to either as time or as a proportion of a frame 
 # If both ms and frame delays are set then the frame one will be used.
@@ -81,31 +89,46 @@
 # BIG FLASHING NOTE IN BOLD: No additional buffering is provided so if delay is sufficently large
 #                            that the transmit doesn't complete until after the next frame starts 
 #                            then the message will get corrupted.
+--------------------------------
 #   Delay the serial by a fixed number of ms
 //DelaySerial=5.2
+
 #   Delay the serial by a fraction of a frame
 //DelaySerialFrame=0.3
+
 #   Delay the serial by a fixed number of ms
 //DelayUDP=5.2
+
 #   Delay the serial by a fraction of a frame
 //DelayUDPFrame=0.3
-
+--------------------------------
 
-# Orientation control 
+[Orientation control]
 #   These options allow an offset to be added to an orientation value and the direction of the axis to be reversed.
 #   Offsets are added BEFORE reversing the direction, if offsetting an inverted channel you may need the opposite direction.
 #   Offsets are integer values, inverts are 1 to flip the axis, any other value to maintain direction.
+--------------------------------
 //OffsetRoll=0
 //OffsetPitch=0
 //OffsetYaw=0
 //InvertRoll=1 
 //InvertPitch=1 
 //InvertYaw=1 
- 
-#  Autohypersmooth
+ --------------------------------
+[Autohypersmooth]
 #    A value of 1 will enable this, 0 will disable it.
 #    Default is enabled.
+--------------------------------
 //AutoHyperSmooth=0
+--------------------------------
+
+[Sync Options]
+#   Enable Force PPF option to force the Fixbox to use PPF instead of Genlock Sync (Tri/Bi Level)
+#   WARNING: This will stop the FIzbox from using Genlock Sync Completely, only enable if using a Lockit
+--------------------------------
+// ForcePPF=1
+--------------------------------
+
 
 [NOTES]
 - All settings are case sensitive.