USBMSD
USBMSD class hierarchy
You can use the USBMSD interface to emulate a mass storage device over USB. You can use this class to store or load data to and from a storage chip, such as SDcard or Flash. This class implements the MSD protocol and takes in a BlockDevice to interact with a storage chip.
USBMSD class reference
| Public Member Functions | |
| USBMSD (mbed::BlockDevice *bd, bool connect_blocking=true, uint16_t vendor_id=0x0703, uint16_t product_id=0x0104, uint16_t product_release=0x0001) | |
| Constructor. More... | |
| USBMSD (USBPhy *phy, mbed::BlockDevice *bd, uint16_t vendor_id, uint16_t product_id, uint16_t product_release) | |
| Fully featured constructor. More... | |
| virtual | ~USBMSD () |
| Destroy this object. More... | |
| bool | connect () |
| Connect the USB MSD device. More... | |
| void | disconnect () |
| Disconnect the USB MSD device. More... | |
| void | process () |
| Perform USB processing. More... | |
| void | attach (mbed::Callback< void()> cb) |
| Called when USBMSD needs to perform processing. More... | |
| bool | media_removed () |
| Check if MSD device was removed/unmounted on the host side. More... | |
| void | init () |
| Initialize this instance. More... | |
| void | deinit () |
| Power down this instance. More... | |
| bool | configured () |
| Check if the device is configured. More... | |
| void | sof_enable () |
| Enable the start of frame interrupt. More... | |
| void | sof_disable () |
| Disable the start of frame interrupt. More... | |
| bool | endpoint_add (usb_ep_t endpoint, uint32_t max_packet, usb_ep_type_t type, mbed::Callback< void()> callback=nullptr) |
| Add an endpoint. More... | |
| template<typename T > | |
| bool | endpoint_add (usb_ep_t endpoint, uint32_t max_packet, usb_ep_type_t type, void(T::*callback)()) |
| Add an endpoint. More... | |
| void | endpoint_remove (usb_ep_t endpoint) |
| Remove an endpoint. More... | |
| void | endpoint_remove_all () |
| Remove all non-zero endpoints. More... | |
| void | endpoint_stall (usb_ep_t endpoint) |
| Stall an endpoint. More... | |
| void | endpoint_unstall (usb_ep_t endpoint) |
| Un-stall an endpoint. More... | |
| uint32_t | endpoint_max_packet_size (usb_ep_t endpoint) |
| Get the current maximum size for this endpoint. More... | |
| void | endpoint_abort (usb_ep_t endpoint) |
| Abort the current transfer on this endpoint. More... | |
| bool | read_start (usb_ep_t endpoint, uint8_t *buffer, uint32_t size) |
| start a read on the given endpoint More... | |
| uint32_t | read_finish (usb_ep_t endpoint) |
| Get the status of a read. More... | |
| bool | write_start (usb_ep_t endpoint, uint8_t *buffer, uint32_t size) |
| Write a data to the given endpoint. More... | |
| uint32_t | write_finish (usb_ep_t endpoint) |
| Get the status of a write. More... | |
| Protected Member Functions | |
| virtual void | callback_power (bool powered) |
| Called by USBDevice layer on power state change. More... | |
| virtual void | callback_sof (int frame_number) |
| Called by USBDevice layer on each new USB frame. More... | |
| virtual void | callback_reset () |
| Called by USBDevice layer on bus reset. More... | |
| void | complete_request (RequestResult result, uint8_t *data=NULL, uint32_t size=0) |
| Called to complete the setup stage of a callback request. More... | |
| void | complete_request_xfer_done (bool success) |
| Called to complete the data stage of a callback request. More... | |
| void | complete_set_configuration (bool success) |
| Called to complete a set configuration command. More... | |
| void | complete_set_interface (bool success) |
| Called to complete a set interface command. More... | |
| uint8_t * | find_descriptor (uint8_t descriptor_type, uint8_t index=0) |
| Find a descriptor type inside the configuration descriptor. More... | |
| const usb_ep_table_t * | endpoint_table () |
| Get the endpoint table of this device. More... | |
| virtual void | start_process () |
| Callback called to indicate the USB processing needs to be done. More... | |
| virtual void | lock () |
| Acquire exclusive access to this instance USBDevice. More... | |
| virtual void | unlock () |
| Release exclusive access to this instance USBDevice. More... | |
| virtual void | assert_locked () |
| Assert that the current thread of execution holds the lock. More... | |
USBMSD SDBlockDevice example
/*
* Copyright (c) 2006-2020 Arm Limited and affiliates.
* SPDX-License-Identifier: Apache-2.0
*/
#include "mbed.h"
#include "SDBlockDevice.h"
#include "USBMSD.h"
SDBlockDevice sd(PTE3, PTE1, PTE2, PTE4);
USBMSD usb(&sd);
int main()
{
while (true) {
usb.process();
}
return 0;
}
USBMSD HeapBlockDevice example
/*
* Copyright (c) 2006-2020 Arm Limited and affiliates.
* SPDX-License-Identifier: Apache-2.0
*/
#include "mbed.h"
#include "USBMSD.h"
#include "FATFileSystem.h"
#define DEFAULT_BLOCK_SIZE 512
#define HEAP_BLOCK_DEVICE_SIZE (128 * DEFAULT_BLOCK_SIZE)
FATFileSystem heap_fs("heap_fs");
HeapBlockDevice bd(HEAP_BLOCK_DEVICE_SIZE, DEFAULT_BLOCK_SIZE);
int main()
{
bd.init();
FATFileSystem::format(&bd);
int err = heap_fs.mount(&bd);
if (err) {
printf("%s filesystem mount failed\ntry to reformat device... \r\n", heap_fs.getName());
err = heap_fs.reformat(&bd);
}
// If still error, then report failure
if (err) {
printf("Error: Unable to format/mount the device.\r\n");
while (1);
}
USBMSD usb(&bd);
while (true) {
usb.process();
}
return 0;
}