雄介 太田
mbed(SerialHalfDuplex入り)
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F302R8/stm32f3xx_hal_uart.h
- Revision:
- 90:cb3d968589d8
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_NUCLEO_F302R8/stm32f3xx_hal_uart.h Tue Oct 28 16:40:41 2014 +0000
@@ -0,0 +1,1064 @@
+/**
+ ******************************************************************************
+ * @file stm32f3xx_hal_uart.h
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 12-Sept-2014
+ * @brief Header file of UART HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F3xx_HAL_UART_H
+#define __STM32F3xx_HAL_UART_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f3xx_hal_def.h"
+
+/** @addtogroup STM32F3xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup UART
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup UART_Exported_Types UART Exported Types
+ * @{
+ */
+
+/**
+ * @brief UART Init Structure definition
+ */
+typedef struct
+{
+ uint32_t BaudRate; /*!< This member configures the UART communication baud rate.
+ The baud rate register is computed using the following formula:
+ - If oversampling is 16 or in LIN mode,
+ Baud Rate Register = ((PCLKx) / ((huart->Init.BaudRate)))
+ - If oversampling is 8,
+ Baud Rate Register[15:4] = ((2 * PCLKx) / ((huart->Init.BaudRate)))[15:4]
+ Baud Rate Register[3] = 0
+ Baud Rate Register[2:0] = (((2 * PCLKx) / ((huart->Init.BaudRate)))[3:0]) >> 1 */
+
+ uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
+ This parameter can be a value of @ref UARTEx_Word_Length */
+
+ uint32_t StopBits; /*!< Specifies the number of stop bits transmitted.
+ This parameter can be a value of @ref UART_Stop_Bits */
+
+ uint32_t Parity; /*!< Specifies the parity mode.
+ This parameter can be a value of @ref UART_Parity
+ @note When parity is enabled, the computed parity is inserted
+ at the MSB position of the transmitted data (9th bit when
+ the word length is set to 9 data bits; 8th bit when the
+ word length is set to 8 data bits). */
+
+ uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
+ This parameter can be a value of @ref UART_Mode */
+
+ uint32_t HwFlowCtl; /*!< Specifies whether the hardware flow control mode is enabled
+ or disabled.
+ This parameter can be a value of @ref UART_Hardware_Flow_Control */
+
+ uint32_t OverSampling; /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8).
+ This parameter can be a value of @ref UART_Over_Sampling */
+
+ uint32_t OneBitSampling; /*!< Specifies whether a single sample or three samples' majority vote is selected.
+ Selecting the single sample method increases the receiver tolerance to clock
+ deviations. This parameter can be a value of @ref UART_OneBit_Sampling. */
+}UART_InitTypeDef;
+
+/**
+ * @brief UART Advanced Features initalization structure definition
+ */
+typedef struct
+{
+ uint32_t AdvFeatureInit; /*!< Specifies which advanced UART features is initialized. Several
+ Advanced Features may be initialized at the same time .
+ This parameter can be a value of @ref UART_Advanced_Features_Initialization_Type */
+
+ uint32_t TxPinLevelInvert; /*!< Specifies whether the TX pin active level is inverted.
+ This parameter can be a value of @ref UART_Tx_Inv */
+
+ uint32_t RxPinLevelInvert; /*!< Specifies whether the RX pin active level is inverted.
+ This parameter can be a value of @ref UART_Rx_Inv */
+
+ uint32_t DataInvert; /*!< Specifies whether data are inverted (positive/direct logic
+ vs negative/inverted logic).
+ This parameter can be a value of @ref UART_Data_Inv */
+
+ uint32_t Swap; /*!< Specifies whether TX and RX pins are swapped.
+ This parameter can be a value of @ref UART_Rx_Tx_Swap */
+
+ uint32_t OverrunDisable; /*!< Specifies whether the reception overrun detection is disabled.
+ This parameter can be a value of @ref UART_Overrun_Disable */
+
+ uint32_t DMADisableonRxError; /*!< Specifies whether the DMA is disabled in case of reception error.
+ This parameter can be a value of @ref UART_DMA_Disable_on_Rx_Error */
+
+ uint32_t AutoBaudRateEnable; /*!< Specifies whether auto Baud rate detection is enabled.
+ This parameter can be a value of @ref UART_AutoBaudRate_Enable */
+
+ uint32_t AutoBaudRateMode; /*!< If auto Baud rate detection is enabled, specifies how the rate
+ detection is carried out.
+ This parameter can be a value of @ref UART_AutoBaud_Rate_Mode */
+
+ uint32_t MSBFirst; /*!< Specifies whether MSB is sent first on UART line.
+ This parameter can be a value of @ref UART_MSB_First */
+} UART_AdvFeatureInitTypeDef;
+
+/**
+ * @brief UART wake up from stop mode parameters
+ */
+typedef struct
+{
+ uint32_t WakeUpEvent; /*!< Specifies which event will activat the Wakeup from Stop mode flag (WUF).
+ This parameter can be a value of @ref UART_WakeUp_from_Stop_Selection.
+ If set to UART_WAKEUP_ON_ADDRESS, the two other fields below must
+ be filled up. */
+
+ uint16_t AddressLength; /*!< Specifies whether the address is 4 or 7-bit long.
+ This parameter can be a value of @ref UART_WakeUp_Address_Length */
+
+ uint8_t Address; /*!< UART/USART node address (7-bit long max) */
+} UART_WakeUpTypeDef;
+
+/**
+ * @brief HAL UART State structures definition
+ */
+typedef enum
+{
+ HAL_UART_STATE_RESET = 0x00, /*!< Peripheral is not initialized */
+ HAL_UART_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */
+ HAL_UART_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
+ HAL_UART_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */
+ HAL_UART_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */
+ HAL_UART_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */
+ HAL_UART_STATE_TIMEOUT = 0x03, /*!< Timeout state */
+ HAL_UART_STATE_ERROR = 0x04 /*!< Error */
+}HAL_UART_StateTypeDef;
+
+/**
+ * @brief HAL UART Error Code structure definition
+ */
+typedef enum
+{
+ HAL_UART_ERROR_NONE = 0x00, /*!< No error */
+ HAL_UART_ERROR_PE = 0x01, /*!< Parity error */
+ HAL_UART_ERROR_NE = 0x02, /*!< Noise error */
+ HAL_UART_ERROR_FE = 0x04, /*!< frame error */
+ HAL_UART_ERROR_ORE = 0x08, /*!< Overrun error */
+ HAL_UART_ERROR_DMA = 0x10 /*!< DMA transfer error */
+}HAL_UART_ErrorTypeDef;
+
+/**
+ * @brief UART clock sources definition
+ */
+typedef enum
+{
+ UART_CLOCKSOURCE_PCLK1 = 0x00, /*!< PCLK1 clock source */
+ UART_CLOCKSOURCE_PCLK2 = 0x01, /*!< PCLK2 clock source */
+ UART_CLOCKSOURCE_HSI = 0x02, /*!< HSI clock source */
+ UART_CLOCKSOURCE_SYSCLK = 0x04, /*!< SYSCLK clock source */
+ UART_CLOCKSOURCE_LSE = 0x08, /*!< LSE clock source */
+ UART_CLOCKSOURCE_UNDEFINED = 0x10 /*!< Undefined clock source */
+}UART_ClockSourceTypeDef;
+
+/**
+ * @brief UART handle Structure definition
+ */
+typedef struct
+{
+ USART_TypeDef *Instance; /* UART registers base address */
+
+ UART_InitTypeDef Init; /* UART communication parameters */
+
+ UART_AdvFeatureInitTypeDef AdvancedInit; /* UART Advanced Features initialization parameters */
+
+ uint8_t *pTxBuffPtr; /* Pointer to UART Tx transfer Buffer */
+
+ uint16_t TxXferSize; /* UART Tx Transfer size */
+
+ uint16_t TxXferCount; /* UART Tx Transfer Counter */
+
+ uint8_t *pRxBuffPtr; /* Pointer to UART Rx transfer Buffer */
+
+ uint16_t RxXferSize; /* UART Rx Transfer size */
+
+ uint16_t RxXferCount; /* UART Rx Transfer Counter */
+
+ uint16_t Mask; /* UART Rx RDR register mask */
+
+ DMA_HandleTypeDef *hdmatx; /* UART Tx DMA Handle parameters */
+
+ DMA_HandleTypeDef *hdmarx; /* UART Rx DMA Handle parameters */
+
+ HAL_LockTypeDef Lock; /* Locking object */
+
+ HAL_UART_StateTypeDef State; /* UART communication state */
+
+ HAL_UART_ErrorTypeDef ErrorCode; /* UART Error code */
+
+}UART_HandleTypeDef;
+
+/**
+ * @}
+ */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup UART_Exported_Constants UART Exported Constants
+ * @{
+ */
+
+/** @defgroup UART_Stop_Bits UART Number of Stop Bits
+ * @{
+ */
+#define UART_STOPBITS_1 ((uint32_t)0x0000)
+#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1)
+#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \
+ ((STOPBITS) == UART_STOPBITS_2))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Parity UART Parity
+ * @{
+ */
+#define UART_PARITY_NONE ((uint32_t)0x0000)
+#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE)
+#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
+#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \
+ ((PARITY) == UART_PARITY_EVEN) || \
+ ((PARITY) == UART_PARITY_ODD))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control
+ * @{
+ */
+#define UART_HWCONTROL_NONE ((uint32_t)0x0000)
+#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE)
+#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE)
+#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE))
+#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\
+ (((CONTROL) == UART_HWCONTROL_NONE) || \
+ ((CONTROL) == UART_HWCONTROL_RTS) || \
+ ((CONTROL) == UART_HWCONTROL_CTS) || \
+ ((CONTROL) == UART_HWCONTROL_RTS_CTS))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Mode UART Transfer Mode
+ * @{
+ */
+#define UART_MODE_RX ((uint32_t)USART_CR1_RE)
+#define UART_MODE_TX ((uint32_t)USART_CR1_TE)
+#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
+#define IS_UART_MODE(MODE) ((((MODE) & (~((uint32_t)(UART_MODE_TX_RX)))) == (uint32_t)0x00) && ((MODE) != (uint32_t)0x00))
+/**
+ * @}
+ */
+
+ /** @defgroup UART_State UART State
+ * @{
+ */
+#define UART_STATE_DISABLE ((uint32_t)0x0000)
+#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE)
+#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \
+ ((STATE) == UART_STATE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Over_Sampling UART Over Sampling
+ * @{
+ */
+#define UART_OVERSAMPLING_16 ((uint32_t)0x0000)
+#define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8)
+#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \
+ ((SAMPLING) == UART_OVERSAMPLING_8))
+/**
+ * @}
+ */
+
+/** @defgroup UART_OneBit_Sampling UART One Bit Sampling Method
+ * @{
+ */
+#define UART_ONEBIT_SAMPLING_DISABLED ((uint32_t)0x0000)
+#define UART_ONEBIT_SAMPLING_ENABLED ((uint32_t)USART_CR3_ONEBIT)
+#define IS_UART_ONEBIT_SAMPLING(ONEBIT) (((ONEBIT) == UART_ONEBIT_SAMPLING_DISABLED) || \
+ ((ONEBIT) == UART_ONEBIT_SAMPLING_ENABLED))
+/**
+ * @}
+ */
+
+/** @defgroup UART_AutoBaud_Rate_Mode UART Advanced Feature AutoBaud Rate Mode
+ * @{
+ */
+#define UART_ADVFEATURE_AUTOBAUDRATE_ONSTARTBIT ((uint32_t)0x0000)
+#define UART_ADVFEATURE_AUTOBAUDRATE_ONFALLINGEDGE ((uint32_t)USART_CR2_ABRMODE_0)
+#define UART_ADVFEATURE_AUTOBAUDRATE_ON0X7FFRAME ((uint32_t)USART_CR2_ABRMODE_1)
+#define UART_ADVFEATURE_AUTOBAUDRATE_ON0X55FRAME ((uint32_t)USART_CR2_ABRMODE)
+#define IS_UART_ADVFEATURE_AUTOBAUDRATEMODE(MODE) (((MODE) == UART_ADVFEATURE_AUTOBAUDRATE_ONSTARTBIT) || \
+ ((MODE) == UART_ADVFEATURE_AUTOBAUDRATE_ONFALLINGEDGE) || \
+ ((MODE) == UART_ADVFEATURE_AUTOBAUDRATE_ON0X7FFRAME) || \
+ ((MODE) == UART_ADVFEATURE_AUTOBAUDRATE_ON0X55FRAME))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Receiver_TimeOut UART Receiver TimeOut
+ * @{
+ */
+#define UART_RECEIVER_TIMEOUT_DISABLE ((uint32_t)0x00000000)
+#define UART_RECEIVER_TIMEOUT_ENABLE ((uint32_t)USART_CR2_RTOEN)
+#define IS_UART_RECEIVER_TIMEOUT(TIMEOUT) (((TIMEOUT) == UART_RECEIVER_TIMEOUT_DISABLE) || \
+ ((TIMEOUT) == UART_RECEIVER_TIMEOUT_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_LIN UART Local Interconnection Network mode
+ * @{
+ */
+#define UART_LIN_DISABLE ((uint32_t)0x00000000)
+#define UART_LIN_ENABLE ((uint32_t)USART_CR2_LINEN)
+#define IS_UART_LIN(LIN) (((LIN) == UART_LIN_DISABLE) || \
+ ((LIN) == UART_LIN_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_LIN_Break_Detection UART LIN Break Detection
+ * @{
+ */
+#define UART_LINBREAKDETECTLENGTH_10B ((uint32_t)0x00000000)
+#define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)USART_CR2_LBDL)
+#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \
+ ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B))
+/**
+ * @}
+ */
+
+
+
+/** @defgroup UART_One_Bit UART One Bit sampling
+ * @{
+ */
+#define UART_ONE_BIT_SAMPLE_DISABLED ((uint32_t)0x00000000)
+#define UART_ONE_BIT_SAMPLE_ENABLED ((uint32_t)USART_CR3_ONEBIT)
+#define IS_UART_ONEBIT_SAMPLE(ONEBIT) (((ONEBIT) == UART_ONE_BIT_SAMPLE_DISABLED) || \
+ ((ONEBIT) == UART_ONE_BIT_SAMPLE_ENABLED))
+/**
+ * @}
+ */
+
+/** @defgroup UART_DMA_Tx UART DMA Tx
+ * @{
+ */
+#define UART_DMA_TX_DISABLE ((uint32_t)0x00000000)
+#define UART_DMA_TX_ENABLE ((uint32_t)USART_CR3_DMAT)
+#define IS_UART_DMA_TX(DMATX) (((DMATX) == UART_DMA_TX_DISABLE) || \
+ ((DMATX) == UART_DMA_TX_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_DMA_Rx UART DMA Rx
+ * @{
+ */
+#define UART_DMA_RX_DISABLE ((uint32_t)0x0000)
+#define UART_DMA_RX_ENABLE ((uint32_t)USART_CR3_DMAR)
+#define IS_UART_DMA_RX(DMARX) (((DMARX) == UART_DMA_RX_DISABLE) || \
+ ((DMARX) == UART_DMA_RX_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Half_Duplex_Selection UART Half Duplex Selection
+ * @{
+ */
+#define UART_HALF_DUPLEX_DISABLE ((uint32_t)0x0000)
+#define UART_HALF_DUPLEX_ENABLE ((uint32_t)USART_CR3_HDSEL)
+#define IS_UART_HALF_DUPLEX(HDSEL) (((HDSEL) == UART_HALF_DUPLEX_DISABLE) || \
+ ((HDSEL) == UART_HALF_DUPLEX_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_WakeUp_Methods UART WakeUp Methods
+ * @{
+ */
+#define UART_WAKEUPMETHOD_IDLELINE ((uint32_t)0x00000000)
+#define UART_WAKEUPMETHOD_ADDRESSMARK ((uint32_t)USART_CR1_WAKE)
+#define IS_UART_WAKEUPMETHOD(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHOD_IDLELINE) || \
+ ((WAKEUP) == UART_WAKEUPMETHOD_ADDRESSMARK))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Flags UART Status Flags
+ * Elements values convention: 0xXXXX
+ * - 0xXXXX : Flag mask in the ISR register
+ * @{
+ */
+#define UART_FLAG_REACK ((uint32_t)0x00400000)
+#define UART_FLAG_TEACK ((uint32_t)0x00200000)
+#define UART_FLAG_WUF ((uint32_t)0x00100000)
+#define UART_FLAG_RWU ((uint32_t)0x00080000)
+#define UART_FLAG_SBKF ((uint32_t)0x00040000
+#define UART_FLAG_CMF ((uint32_t)0x00020000)
+#define UART_FLAG_BUSY ((uint32_t)0x00010000)
+#define UART_FLAG_ABRF ((uint32_t)0x00008000)
+#define UART_FLAG_ABRE ((uint32_t)0x00004000)
+#define UART_FLAG_EOBF ((uint32_t)0x00001000)
+#define UART_FLAG_RTOF ((uint32_t)0x00000800)
+#define UART_FLAG_CTS ((uint32_t)0x00000400)
+#define UART_FLAG_CTSIF ((uint32_t)0x00000200)
+#define UART_FLAG_LBDF ((uint32_t)0x00000100)
+#define UART_FLAG_TXE ((uint32_t)0x00000080)
+#define UART_FLAG_TC ((uint32_t)0x00000040)
+#define UART_FLAG_RXNE ((uint32_t)0x00000020)
+#define UART_FLAG_IDLE ((uint32_t)0x00000010)
+#define UART_FLAG_ORE ((uint32_t)0x00000008)
+#define UART_FLAG_NE ((uint32_t)0x00000004)
+#define UART_FLAG_FE ((uint32_t)0x00000002)
+#define UART_FLAG_PE ((uint32_t)0x00000001)
+/**
+ * @}
+ */
+
+/** @defgroup UART_Interrupt_definition UART Interrupts Definition
+ * Elements values convention: 0000ZZZZ0XXYYYYYb
+ * - YYYYY : Interrupt source position in the XX register (5bits)
+ * - XX : Interrupt source register (2bits)
+ * - 01: CR1 register
+ * - 10: CR2 register
+ * - 11: CR3 register
+ * - ZZZZ : Flag position in the ISR register(4bits)
+ * @{
+ */
+#define UART_IT_PE ((uint16_t)0x0028)
+#define UART_IT_TXE ((uint16_t)0x0727)
+#define UART_IT_TC ((uint16_t)0x0626)
+#define UART_IT_RXNE ((uint16_t)0x0525)
+#define UART_IT_IDLE ((uint16_t)0x0424)
+#define UART_IT_LBD ((uint16_t)0x0846)
+#define UART_IT_CTS ((uint16_t)0x096A)
+#define UART_IT_CM ((uint16_t)0x142E)
+#define UART_IT_WUF ((uint16_t)0x1476)
+
+/** Elements values convention: 000000000XXYYYYYb
+ * - YYYYY : Interrupt source position in the XX register (5bits)
+ * - XX : Interrupt source register (2bits)
+ * - 01: CR1 register
+ * - 10: CR2 register
+ * - 11: CR3 register
+ */
+#define UART_IT_ERR ((uint16_t)0x0060)
+
+/** Elements values convention: 0000ZZZZ00000000b
+ * - ZZZZ : Flag position in the ISR register(4bits)
+ */
+#define UART_IT_ORE ((uint16_t)0x0300)
+#define UART_IT_NE ((uint16_t)0x0200)
+#define UART_IT_FE ((uint16_t)0x0100)
+/**
+ * @}
+ */
+
+/** @defgroup UART_IT_CLEAR_Flags UART Interruption Clear Flags
+ * @{
+ */
+#define UART_CLEAR_PEF USART_ICR_PECF /*!< Parity Error Clear Flag */
+#define UART_CLEAR_FEF USART_ICR_FECF /*!< Framing Error Clear Flag */
+#define UART_CLEAR_NEF USART_ICR_NCF /*!< Noise detected Clear Flag */
+#define UART_CLEAR_OREF USART_ICR_ORECF /*!< OverRun Error Clear Flag */
+#define UART_CLEAR_IDLEF USART_ICR_IDLECF /*!< IDLE line detected Clear Flag */
+#define UART_CLEAR_TCF USART_ICR_TCCF /*!< Transmission Complete Clear Flag */
+#define UART_CLEAR_LBDF USART_ICR_LBDCF /*!< LIN Break Detection Clear Flag */
+#define UART_CLEAR_CTSF USART_ICR_CTSCF /*!< CTS Interrupt Clear Flag */
+#define UART_CLEAR_RTOF USART_ICR_RTOCF /*!< Receiver Time Out Clear Flag */
+#define UART_CLEAR_EOBF USART_ICR_EOBCF /*!< End Of Block Clear Flag */
+#define UART_CLEAR_CMF USART_ICR_CMCF /*!< Character Match Clear Flag */
+#define UART_CLEAR_WUF USART_ICR_WUCF /*!< Wake Up from stop mode Clear Flag */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Request_Parameters UART Request Parameters
+ * @{
+ */
+#define UART_AUTOBAUD_REQUEST ((uint32_t)USART_RQR_ABRRQ) /*!< Auto-Baud Rate Request */
+#define UART_SENDBREAK_REQUEST ((uint32_t)USART_RQR_SBKRQ) /*!< Send Break Request */
+#define UART_MUTE_MODE_REQUEST ((uint32_t)USART_RQR_MMRQ) /*!< Mute Mode Request */
+#define UART_RXDATA_FLUSH_REQUEST ((uint32_t)USART_RQR_RXFRQ) /*!< Receive Data flush Request */
+#define UART_TXDATA_FLUSH_REQUEST ((uint32_t)USART_RQR_TXFRQ) /*!< Transmit data flush Request */
+#define IS_UART_REQUEST_PARAMETER(PARAM) (((PARAM) == UART_AUTOBAUD_REQUEST) || \
+ ((PARAM) == UART_SENDBREAK_REQUEST) || \
+ ((PARAM) == UART_MUTE_MODE_REQUEST) || \
+ ((PARAM) == UART_RXDATA_FLUSH_REQUEST) || \
+ ((PARAM) == UART_TXDATA_FLUSH_REQUEST))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Advanced_Features_Initialization_Type UART Advanced Feature Initialization Type
+ * @{
+ */
+#define UART_ADVFEATURE_NO_INIT ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_TXINVERT_INIT ((uint32_t)0x00000001)
+#define UART_ADVFEATURE_RXINVERT_INIT ((uint32_t)0x00000002)
+#define UART_ADVFEATURE_DATAINVERT_INIT ((uint32_t)0x00000004)
+#define UART_ADVFEATURE_SWAP_INIT ((uint32_t)0x00000008)
+#define UART_ADVFEATURE_RXOVERRUNDISABLE_INIT ((uint32_t)0x00000010)
+#define UART_ADVFEATURE_DMADISABLEONERROR_INIT ((uint32_t)0x00000020)
+#define UART_ADVFEATURE_AUTOBAUDRATE_INIT ((uint32_t)0x00000040)
+#define UART_ADVFEATURE_MSBFIRST_INIT ((uint32_t)0x00000080)
+#define IS_UART_ADVFEATURE_INIT(INIT) ((INIT) <= (UART_ADVFEATURE_NO_INIT | \
+ UART_ADVFEATURE_TXINVERT_INIT | \
+ UART_ADVFEATURE_RXINVERT_INIT | \
+ UART_ADVFEATURE_DATAINVERT_INIT | \
+ UART_ADVFEATURE_SWAP_INIT | \
+ UART_ADVFEATURE_RXOVERRUNDISABLE_INIT | \
+ UART_ADVFEATURE_DMADISABLEONERROR_INIT | \
+ UART_ADVFEATURE_AUTOBAUDRATE_INIT | \
+ UART_ADVFEATURE_MSBFIRST_INIT))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Tx_Inv UART Advanced Feature TX Pin Active Level Inversion
+ * @{
+ */
+#define UART_ADVFEATURE_TXINV_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_TXINV_ENABLE ((uint32_t)USART_CR2_TXINV)
+#define IS_UART_ADVFEATURE_TXINV(TXINV) (((TXINV) == UART_ADVFEATURE_TXINV_DISABLE) || \
+ ((TXINV) == UART_ADVFEATURE_TXINV_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Rx_Inv UART Advanced Feature RX Pin Active Level Inversion
+ * @{
+ */
+#define UART_ADVFEATURE_RXINV_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_RXINV_ENABLE ((uint32_t)USART_CR2_RXINV)
+#define IS_UART_ADVFEATURE_RXINV(RXINV) (((RXINV) == UART_ADVFEATURE_RXINV_DISABLE) || \
+ ((RXINV) == UART_ADVFEATURE_RXINV_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Data_Inv UART Advanced Feature Binary Data Inversion
+ * @{
+ */
+#define UART_ADVFEATURE_DATAINV_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_DATAINV_ENABLE ((uint32_t)USART_CR2_DATAINV)
+#define IS_UART_ADVFEATURE_DATAINV(DATAINV) (((DATAINV) == UART_ADVFEATURE_DATAINV_DISABLE) || \
+ ((DATAINV) == UART_ADVFEATURE_DATAINV_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Rx_Tx_Swap UART Advanced Feature RX TX Pins Swap
+ * @{
+ */
+#define UART_ADVFEATURE_SWAP_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_SWAP_ENABLE ((uint32_t)USART_CR2_SWAP)
+#define IS_UART_ADVFEATURE_SWAP(SWAP) (((SWAP) == UART_ADVFEATURE_SWAP_DISABLE) || \
+ ((SWAP) == UART_ADVFEATURE_SWAP_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Overrun_Disable UART Advanced Feature Overrun Disable
+ * @{
+ */
+#define UART_ADVFEATURE_OVERRUN_ENABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_OVERRUN_DISABLE ((uint32_t)USART_CR3_OVRDIS)
+#define IS_UART_OVERRUN(OVERRUN) (((OVERRUN) == UART_ADVFEATURE_OVERRUN_ENABLE) || \
+ ((OVERRUN) == UART_ADVFEATURE_OVERRUN_DISABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_AutoBaudRate_Enable UART Advanced Feature Auto BaudRate Enable
+ * @{
+ */
+#define UART_ADVFEATURE_AUTOBAUDRATE_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_AUTOBAUDRATE_ENABLE ((uint32_t)USART_CR2_ABREN)
+#define IS_UART_ADVFEATURE_AUTOBAUDRATE(AUTOBAUDRATE) (((AUTOBAUDRATE) == UART_ADVFEATURE_AUTOBAUDRATE_DISABLE) || \
+ ((AUTOBAUDRATE) == UART_ADVFEATURE_AUTOBAUDRATE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_DMA_Disable_on_Rx_Error UART Advanced Feature DMA Disable On Rx Error
+ * @{
+ */
+#define UART_ADVFEATURE_DMA_ENABLEONRXERROR ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_DMA_DISABLEONRXERROR ((uint32_t)USART_CR3_DDRE)
+#define IS_UART_ADVFEATURE_DMAONRXERROR(DMA) (((DMA) == UART_ADVFEATURE_DMA_ENABLEONRXERROR) || \
+ ((DMA) == UART_ADVFEATURE_DMA_DISABLEONRXERROR))
+/**
+ * @}
+ */
+
+/** @defgroup UART_MSB_First UART Advanced Feature MSB First
+ * @{
+ */
+#define UART_ADVFEATURE_MSBFIRST_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_MSBFIRST_ENABLE ((uint32_t)USART_CR2_MSBFIRST)
+#define IS_UART_ADVFEATURE_MSBFIRST(MSBFIRST) (((MSBFIRST) == UART_ADVFEATURE_MSBFIRST_DISABLE) || \
+ ((MSBFIRST) == UART_ADVFEATURE_MSBFIRST_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Stop_Mode_Enable UART Advanced Feature Stop Mode Enable
+ * @{
+ */
+#define UART_ADVFEATURE_STOPMODE_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_STOPMODE_ENABLE ((uint32_t)USART_CR1_UESM)
+#define IS_UART_ADVFEATURE_STOPMODE(STOPMODE) (((STOPMODE) == UART_ADVFEATURE_STOPMODE_DISABLE) || \
+ ((STOPMODE) == UART_ADVFEATURE_STOPMODE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Mute_Mode UART Advanced Feature Mute Mode Enable
+ * @{
+ */
+#define UART_ADVFEATURE_MUTEMODE_DISABLE ((uint32_t)0x00000000)
+#define UART_ADVFEATURE_MUTEMODE_ENABLE ((uint32_t)USART_CR1_MME)
+#define IS_UART_MUTE_MODE(MUTE) (((MUTE) == UART_ADVFEATURE_MUTEMODE_DISABLE) || \
+ ((MUTE) == UART_ADVFEATURE_MUTEMODE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_CR2_ADDRESS_LSB_POS UART Address-matching LSB Position In CR2 Register
+ * @{
+ */
+#define UART_CR2_ADDRESS_LSB_POS ((uint32_t) 24)
+/**
+ * @}
+ */
+
+/** @defgroup UART_WakeUp_from_Stop_Selection UART WakeUp From Stop Selection
+ * @{
+ */
+#define UART_WAKEUP_ON_ADDRESS ((uint32_t)0x0000)
+#define UART_WAKEUP_ON_STARTBIT ((uint32_t)USART_CR3_WUS_1)
+#define UART_WAKEUP_ON_READDATA_NONEMPTY ((uint32_t)USART_CR3_WUS)
+#define IS_UART_WAKEUP_SELECTION(WAKE) (((WAKE) == UART_WAKEUP_ON_ADDRESS) || \
+ ((WAKE) == UART_WAKEUP_ON_STARTBIT) || \
+ ((WAKE) == UART_WAKEUP_ON_READDATA_NONEMPTY))
+/**
+ * @}
+ */
+
+/** @defgroup UART_DriverEnable_Polarity UART DriverEnable Polarity
+ * @{
+ */
+#define UART_DE_POLARITY_HIGH ((uint32_t)0x00000000)
+#define UART_DE_POLARITY_LOW ((uint32_t)USART_CR3_DEP)
+#define IS_UART_DE_POLARITY(POLARITY) (((POLARITY) == UART_DE_POLARITY_HIGH) || \
+ ((POLARITY) == UART_DE_POLARITY_LOW))
+/**
+ * @}
+ */
+
+/** @defgroup UART_CR1_DEAT_ADDRESS_LSB_POS UART Driver Enable Assertion Time LSB Position In CR1 Register
+ * @{
+ */
+#define UART_CR1_DEAT_ADDRESS_LSB_POS ((uint32_t) 21)
+/**
+ * @}
+ */
+
+/** @defgroup UART_CR1_DEDT_ADDRESS_LSB_POS UART Driver Enable DeAssertion Time LSB Position In CR1 Register
+ * @{
+ */
+#define UART_CR1_DEDT_ADDRESS_LSB_POS ((uint32_t) 16)
+/**
+ * @}
+ */
+
+/** @defgroup UART_Interruption_Mask UART Interruptions Flag Mask
+ * @{
+ */
+#define UART_IT_MASK ((uint32_t)0x001F)
+/**
+ * @}
+ */
+
+/** @defgroup UART_TimeOut_Value UART polling-based communications time-out value
+ * @{
+ */
+#define HAL_UART_TIMEOUT_VALUE 0x1FFFFFF
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup UART_Exported_Macros UART Exported Macros
+ * @{
+ */
+
+/** @brief Reset UART handle state
+ * @param __HANDLE__: UART handle.
+ * @retval None
+ */
+#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_UART_STATE_RESET)
+
+/** @brief Checks whether the specified UART flag is set or not.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or
+ * UART peripheral (datasheet: up to five USART/UARTs)
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg UART_FLAG_REACK: Receive enable ackowledge flag
+ * @arg UART_FLAG_TEACK: Transmit enable ackowledge flag
+ * @arg UART_FLAG_WUF: Wake up from stop mode flag
+ * @arg UART_FLAG_RWU: Receiver wake up flag (is the UART in mute mode)
+ * @arg UART_FLAG_SBKF: Send Break flag
+ * @arg UART_FLAG_CMF: Character match flag
+ * @arg UART_FLAG_BUSY: Busy flag
+ * @arg UART_FLAG_ABRF: Auto Baud rate detection flag
+ * @arg UART_FLAG_ABRE: Auto Baud rate detection error flag
+ * @arg UART_FLAG_EOBF: End of block flag
+ * @arg UART_FLAG_RTOF: Receiver timeout flag
+ * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5)
+ * @arg UART_FLAG_LBD: LIN Break detection flag
+ * @arg UART_FLAG_TXE: Transmit data register empty flag
+ * @arg UART_FLAG_TC: Transmission Complete flag
+ * @arg UART_FLAG_RXNE: Receive data register not empty flag
+ * @arg UART_FLAG_IDLE: Idle Line detection flag
+ * @arg UART_FLAG_ORE: OverRun Error flag
+ * @arg UART_FLAG_NE: Noise Error flag
+ * @arg UART_FLAG_FE: Framing Error flag
+ * @arg UART_FLAG_PE: Parity Error flag
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))
+
+/** @brief Enables the specified UART interrupt.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or
+ * UART peripheral. (datasheet: up to five USART/UARTs)
+ * @param __INTERRUPT__: specifies the UART interrupt source to enable.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_WUF: Wakeup from stop mode interrupt
+ * @arg UART_IT_CM: Character match interrupt
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @retval None
+ */
+#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((__HANDLE__)->Instance->CR3 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))))
+
+
+/** @brief Disables the specified UART interrupt.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or
+ * UART peripheral. (datasheet: up to five USART/UARTs)
+ * @param __INTERRUPT__: specifies the UART interrupt source to disable.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_WUF: Wakeup from stop mode interrupt
+ * @arg UART_IT_CM: Character match interrupt
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @retval None
+ */
+#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((__HANDLE__)->Instance->CR3 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))))
+
+/** @brief Checks whether the specified UART interrupt has occurred or not.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or
+ * UART peripheral. (datasheet: up to five USART/UARTs)
+ * @param __IT__: specifies the UART interrupt to check.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_WUF: Wakeup from stop mode interrupt
+ * @arg UART_IT_CM: Character match interrupt
+ * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg UART_IT_LBD: LIN Break detection interrupt
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_ORE: OverRun Error interrupt
+ * @arg UART_IT_NE: Noise Error interrupt
+ * @arg UART_IT_FE: Framing Error interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @retval The new state of __IT__ (TRUE or FALSE).
+ */
+#define __HAL_UART_GET_IT(__HANDLE__, __IT__) ((__HANDLE__)->Instance->ISR & ((uint32_t)1 << ((__IT__)>> 0x08)))
+
+/** @brief Checks whether the specified UART interrupt source is enabled.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or
+ * UART peripheral. (datasheet: up to five USART/UARTs)
+ * @param __IT__: specifies the UART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg UART_IT_LBD: LIN Break detection interrupt
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_ORE: OverRun Error interrupt
+ * @arg UART_IT_NE: Noise Error interrupt
+ * @arg UART_IT_FE: Framing Error interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @retval The new state of __IT__ (TRUE or FALSE).
+ */
+#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) ((((((uint8_t)(__IT__)) >> 5U) == 1)? (__HANDLE__)->Instance->CR1:(((((uint8_t)(__IT__)) >> 5U) == 2)? \
+ (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & ((uint32_t)1 << (((uint16_t)(__IT__)) & UART_IT_MASK)))
+
+/** @brief Clears the specified UART ISR flag, in setting the proper ICR register flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or
+ * UART peripheral. (datasheet: up to five USART/UARTs)
+ * @param __IT_CLEAR__: specifies the interrupt clear register flag that needs to be set
+ * to clear the corresponding interrupt
+ * This parameter can be one of the following values:
+ * @arg UART_CLEAR_PEF: Parity Error Clear Flag
+ * @arg UART_CLEAR_FEF: Framing Error Clear Flag
+ * @arg UART_CLEAR_NEF: Noise detected Clear Flag
+ * @arg UART_CLEAR_OREF: OverRun Error Clear Flag
+ * @arg UART_CLEAR_IDLEF: IDLE line detected Clear Flag
+ * @arg UART_CLEAR_TCF: Transmission Complete Clear Flag
+ * @arg UART_CLEAR_LBDF: LIN Break Detection Clear Flag
+ * @arg UART_CLEAR_CTSF: CTS Interrupt Clear Flag
+ * @arg UART_CLEAR_RTOF: Receiver Time Out Clear Flag
+ * @arg UART_CLEAR_EOBF: End Of Block Clear Flag
+ * @arg UART_CLEAR_CMF: Character Match Clear Flag
+ * @arg UART_CLEAR_WUF: Wake Up from stop mode Clear Flag
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))
+
+/** @brief Set a specific UART request flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or
+ * UART peripheral. (datasheet: up to five USART/UARTs)
+ * @param __REQ__: specifies the request flag to set
+ * This parameter can be one of the following values:
+ * @arg UART_AUTOBAUD_REQUEST: Auto-Baud Rate Request
+ * @arg UART_SENDBREAK_REQUEST: Send Break Request
+ * @arg UART_MUTE_MODE_REQUEST: Mute Mode Request
+ * @arg UART_RXDATA_FLUSH_REQUEST: Receive Data flush Request
+ * @arg UART_TXDATA_FLUSH_REQUEST: Transmit data flush Request
+ * @retval None
+ */
+#define __HAL_UART_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint32_t)(__REQ__))
+
+/** @brief Enable UART
+ * @param __HANDLE__: specifies the UART Handle.
+ * The Handle Instance can be UARTx where x: 1, 2, 3, 4 or 5 to select the UART peripheral
+ * @retval None
+ */
+#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
+
+/** @brief Disable UART
+ * @param __HANDLE__: specifies the UART Handle.
+ * The Handle Instance can be UARTx where x: 1, 2, 3, 4 or 5 to select the UART peripheral
+ * @retval None
+ */
+#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+
+/** @brief BRR division operation to set BRR register in 8-bit oversampling mode
+ * @param _PCLK_: UART clock
+ * @param _BAUD_: Baud rate set by the user
+ * @retval Division result
+ */
+#define __DIV_SAMPLING8(_PCLK_, _BAUD_) (((_PCLK_)*2)/((_BAUD_)))
+
+/** @brief BRR division operation to set BRR register in 16-bit oversampling mode
+ * @param _PCLK_: UART clock
+ * @param _BAUD_: Baud rate set by the user
+ * @retval Division result
+ */
+#define __DIV_SAMPLING16(_PCLK_, _BAUD_) (((_PCLK_))/((_BAUD_)))
+
+/** @brief Check UART Baud rate
+ * @param BAUDRATE: Baudrate specified by the user
+ * The maximum Baud Rate is derived from the maximum clock on F3 (i.e. 72 MHz)
+ * divided by the smallest oversampling used on the USART (i.e. 8)
+ * @retval Test result (TRUE or FALSE).
+ */
+#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 9000001)
+
+/** @brief Check UART assertion time
+ * @param TIME: 5-bit value assertion time
+ * @retval Test result (TRUE or FALSE).
+ */
+#define IS_UART_ASSERTIONTIME(TIME) ((TIME) <= 0x1F)
+
+/** @brief Check UART deassertion time
+ * @param TIME: 5-bit value deassertion time
+ * @retval Test result (TRUE or FALSE).
+ */
+#define IS_UART_DEASSERTIONTIME(TIME) ((TIME) <= 0x1F)
+
+/**
+ * @}
+ */
+
+/* Include UART HAL Extended module */
+#include "stm32f3xx_hal_uart_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup UART_Exported_Functions UART Exported Functions
+ * @{
+ */
+
+/** @addtogroup UART_Exported_Functions_Group1 Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ * @{
+ */
+/* Initialization and de-initialization functions ****************************/
+HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength);
+HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod);
+HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart);
+void HAL_UART_MspInit(UART_HandleTypeDef *huart);
+void HAL_UART_MspDeInit(UART_HandleTypeDef *huart);
+/**
+ * @}
+ */
+
+/** @addtogroup UART_Exported_Functions_Group2 Input and Output operation functions
+ * @brief UART Transmit/Receive functions
+ * @{
+ */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart);
+void HAL_UART_IRQHandler(UART_HandleTypeDef *huart);
+void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart);
+void HAL_UART_WakeupCallback(UART_HandleTypeDef *huart);
+
+HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Timeout);
+/**
+ * @}
+ */
+
+/** @addtogroup UART_Exported_Functions_Group3 Peripheral Control functions
+ * @brief UART control functions
+ * @{
+ */
+/* Peripheral Control functions ***********************************************/
+HAL_StatusTypeDef HAL_MultiProcessor_EnableMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_MultiProcessor_DisableMuteMode(UART_HandleTypeDef *huart);
+void HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef UART_SetConfig(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart);
+
+HAL_StatusTypeDef UART_CheckIdleState(UART_HandleTypeDef *huart);
+void UART_AdvFeatureConfig(UART_HandleTypeDef *huart);
+void UART_Wakeup_AddressConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection);
+/**
+ * @}
+ */
+
+/** @addtogroup UART_Exported_Functions_Group4 Peripheral State and Error functions
+ * @brief Peripheral State and Error functions
+ * @{
+ */
+/* Peripheral State and Error functions ***************************************/
+HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart);
+uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart);
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F3xx_HAL_UART_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/