Control up to two motors using filtered EMG signals and a PID controller
Dependencies: FastPWM HIDScope MODSERIAL QEI Matrix biquadFilter controller errorFetch mbed motorConfig refGen MatrixMath inverseKinematics
Fork of Minor_test_serial by
main.cpp
- Committer:
- tvlogman
- Date:
- 2017-10-20
- Revision:
- 32:1bb406d2b3c3
- Parent:
- 31:cc08254ab7b5
- Child:
- 33:6f4858b98fe5
File content as of revision 32:1bb406d2b3c3:
#include "mbed.h" #include "MODSERIAL.h" #include "HIDScope.h" #include "QEI.h" #include "FastPWM.h" #include "refGen.h" #include "controller.h" #include "motorConfig.h" #include "errorFetch.h" // Defining relevant constant parameters const float gearRatio = 131; // Controller parameters const float k_p = 1; const float k_i = 0; // Still needs a reasonable value const float k_d = 0; // Again, still need to pick a reasonable value QEI Encoder1(D12,D13,NC,64, QEI::X4_ENCODING); QEI Encoder2(D11,D10,NC,64, QEI::X4_ENCODING); MODSERIAL pc(USBTX, USBRX); HIDScope scope(5); // Defining inputs InterruptIn sw2(SW2); InterruptIn sw3(SW3); InterruptIn button1(D2); InterruptIn button2(D3); AnalogIn pot2(A3); AnalogIn emg0( A0 ); //AnalogIn emg1( A1 ); // PWM settings float pwmPeriod = 1.0/5000.0; int frequency_pwm = 10000; //10kHz PWM // Setting up HIDscope volatile float x; volatile float y; volatile float z; volatile float q; volatile float k; void sendDataToPc(float data1, float data2, float data3, float data4, float data5){ // Capture data x = data1; y = data2; z = data3; q = data4; k = data5; scope.set(0, x); scope.set(1, y); scope.set(2, z); scope.set(3, q); scope.set(4, z); scope.send(); // send what's in scope memory to PC } // Initializing encoder Ticker encoderTicker; Ticker controllerTicker; volatile int counts = 0; volatile float revs = 0.00; // MOTOR CONTROL PART bool r_direction = false; int posRevRange = 2; // describes the ends of the position range in complete motor output shaft revolutions in both directions const float maxAngle = 2*3.14*posRevRange; // max angle in radians const float Ts = 0.1; // Function getReferencePosition returns reference angle based on potmeter 1 refGen ref1(A1); //ref.getReferencePosition(maxAngle); // readEncoder reads counts and revs and logs results to serial window errorFetch err1(Encoder1, gearRatio, Ts, ref1); // Generate a PID controller with the specified values of k_p, k_d and k_i controller motorController1(k_p, k_d, k_i); // setMotor1 sets the direction and magnitude pins of motor1 depending on the given motorValue. Negative motorValue means clockwise rotation motorConfig motor1(LED_GREEN,LED_RED,LED_BLUE,D5,D4); void measureAndControl(){ err1.fetchError(); float motorValue = motorController1.control(err1.e_pos, err1.e_int, err1.e_der); float r = ref1.getReferencePosition(ref.maxAngle, ref1.r_direction); sendDataToPc(r, err1.e_pos, emg0.read(), err1.e_der, motorValue); pc.printf("Motorvalue is %.2f \r\n", motorValue); pc.printf("Error is %.2f \r\n", e_pos); pc.printf("Reference is %.2f \r\n", r); //pc.printf("motor1 direction is %d \r\n", motor1_direction.read()); motor1.setMotor(motorValue); } void rSwitchDirection(){ r_direction = !r_direction; pc.printf("Switched reference direction! \r\n"); } int main() { pc.printf("Main function"); sw2.fall(&motor1,&motorConfig::killSwitch); sw3.fall(&motor1, &motorConfig::turnMotorOn); button2.rise(&rSwitchDirection); pc.baud(115200); controllerTicker.attach(measureAndControl, Ts); pc.printf("Encoder ticker attached and baudrate set"); }