File content as of revision 21:4f60d60b2e5a:

#include "mbed.h"
#include "BNO055.h"


//------------------------------------
// Hyperterminal configuration
// 9600 bauds, 8-bit data, no parity
//------------------------------------

Serial pc(SERIAL_TX, SERIAL_RX);

Ticker pwmint;
DigitalOut myled(LED1);
InterruptIn button(USER_BUTTON);

PwmOut P1(PE_9);
DigitalOut EN1(D0);
AnalogIn I1(A0);

//PwmOut P2(PE_11);     1D FOCUS FOR NOW
//PwmOut P3(PE_13);

I2C    i2c(PB_9, PB_8);         // SDA, SCL
BNO055 imu(i2c, PA_8);          // Reset

BNO055_ID_INF_TypeDef   bno055_id_inf;
BNO055_EULER_TypeDef    euler_angles;
BNO055_VEL_TypeDef      velocity;  //IN PROGRESS

double Kbt = -89.9276;
double Kbv = -14.9398;
double Kwv = 0.0;//-0.0909;

double wv;
double bt;
double r1;

double pi = 3.14159265;

int isPressed;

void pwmupdate()
{

    //myled = !myled;
    wv = I1.read(); // Converts and read the analog input value (value from 0.0 to 1.0)
    wv = (wv-2.0)*5000.0; // Scale the velocity to rad/s

    bt = (euler_angles.p - (pi/4.0));

    r1 = (Kbt*bt + Kbv*velocity.z + Kwv*wv);

    

    //Limit PWM range
    if (r1 > 6.0) {
        r1 = 6.0;
    }
    
    if (r1 < -6.0) {
        r1 = -6.0;
    }
        
    r1 = ((.4*(r1/6.0)) + 0.5) ;              //Normalize for PWM output
    
    P1 = r1;
    //P2 = (euler_angles.r/360.0);
    //P3 = (euler_angles.p/360.0);
    if (bt > (pi/8)){
        EN1 = 0;
        pwmint.detach();
        }
        
    else if (bt< -(pi/8)){
        EN1 = 0; 
        pwmint.detach();
        }
        
}

void eventFunction()
{

    if(!isPressed) {
        pwmint.attach(&pwmupdate, .005);
        EN1 = 1;
        myled = 1;
        isPressed=1;

    } else {
        pwmint.detach();
        P1 = 0.5;
        bt = 0.0;
        myled = 0;
        EN1 = 0;
        //P2 = 0;
        //P3 = 0;
        isPressed=0;
    }
}

int main()
{

    pc.printf("Bosch Sensortec BNO055 test program on " __DATE__ "/" __TIME__ "\r\n");
    if (imu.chip_ready() == 0) {
        pc.printf("Bosch BNO055 is NOT available!!\r\n");
    }

    imu.read_id_inf(&bno055_id_inf);
    P1 = .5;        //Stops ESCON studio from throwing out-of-range error
    
    //pc.printf("CHIP:0x%02x, ACC:0x%02x, MAG:0x%02x, GYR:0x%02x, , SW:0x%04x, , BL:0x%02x\r\n",
    //           bno055_id_inf.chip_id, bno055_id_inf.acc_id, bno055_id_inf.mag_id,
    //           bno055_id_inf.gyr_id, bno055_id_inf.sw_rev_id, bno055_id_inf.bootldr_rev_id);

    P1.period(0.0002);      //Set PWM frequency

    isPressed=0;
    button.rise(&eventFunction);        //Enable Closed Loop



    while(1) {


        // pc.printf("H:%+6.4f [rad], P:%+6.4f, R:%+6.4f, R1%+6.4f [PWM], Theta_dot:%+6.4f [rad/s] , WV:%+6.4f [rad/s] \r\n",
        //             euler_angles.h, euler_angles.p, euler_angles.r, r1, velocity.z, wv);

        //pc.printf("Theta:%+6.4f [rad], P:%+6.4f [rad], R1%+6.4f [PWM], Theta_dot:%+6.4f [rad/s], WV:%+6.4f [rad/s] \r\n",
         //         bt, euler_angles.p, r1, velocity.z, wv);

        imu.get_Euler_Angles(&euler_angles);
        imu.get_velocities(&velocity);

        //wait(0.2);
    }
}