File content as of revision 117:5b5ad247cc3b:

/*
 / _____)             _              | |
( (____  _____ ____ _| |_ _____  ____| |__
 \____ \| ___ |    (_   _) ___ |/ ___)  _ \
 _____) ) ____| | | || |_| ____( (___| | | |
(______/|_____)_|_|_| \__)_____)\____)_| |_|
    (C) 2014 Semtech

Description: -

License: Revised BSD License, see LICENSE.TXT file include in the project

Maintainers: Miguel Luis, Gregory Cristian and Nicolas Huguenin
*/

/*
 * additional development to make it more generic across multiple OS versions
 * (c) 2017 Helmut Tschemernjak
 * 30826 Garbsen (Hannover) Germany
 */

#ifndef __SX1276_MBED_HAL_H__
#define __SX1276_MBED_HAL_H__


#include "sx1276.h"


#ifdef __MBED__
#define XSPI	SPI
#endif

#if defined(DEVICE_LPTICKER) || defined(DEVICE_LOWPOWERTIMER) // LOWPOWERTIMER in older mbed versions
 #define MyTimeout LowPowerTimeout
#else
 #define MyTimeout Timeout
#endif

/*!
 * Actual implementation of a SX1276 radio, includes some modifications to make it
 * compatible with the MB1 LAS board
 */
class SX1276Generic : public SX1276
{
protected:
    /*!
     * Antenna switch GPIO pins objects
     */
    DigitalOut *_antSwitchPwr;
    DigitalOut *_antSwitch;
    DigitalOut *_antSwitchTX;
    DigitalOut *_antSwitchTXBoost;

    /*!
     * SX1276 Reset pin
     */
    DigitalInOut *_reset;
    
    /*!
     * TCXO being used with the Murata Module
     */
    DigitalOut *_tcxo;

    /*!
     * SPI Interface
     */
    XSPI *_spi; // mosi, miso, sclk
    DigitalOut *_nss;
    
    /*!
     * SX1276 DIO pins
     */
    InterruptIn *_dio0;
    InterruptIn *_dio1;
    InterruptIn *_dio2;
    InterruptIn *_dio3;
    InterruptIn *_dio4;
    DigitalIn *_dio5;
    
    /*!
     * Tx and Rx timers
     */
    MyTimeout txTimeoutTimer;
    MyTimeout rxTimeoutTimer;
    MyTimeout rxTimeoutSyncWord;
    
    
private:
    /*!
     * triggers definition
     */
    typedef void (SX1276Generic::*Trigger)(void);
    static const int PWR_OFF = 1;
    static const int PWR_ON = 0;
    

public:
    SX1276Generic( RadioEvents_t *events, BoardType_t board,
            PinName mosi, PinName miso, PinName sclk, PinName nss, PinName reset,
            PinName dio0, PinName dio1, PinName dio2, PinName dio3, PinName dio4, PinName dio5,
            PinName antSwitch = NC, PinName antSwitchTX = NC, PinName antSwitchTXBoost = NC, PinName tcxo = NC);

    
    SX1276Generic( RadioEvents_t *events );

    virtual ~SX1276Generic();

protected:
    /*!
     * @brief Initializes the radio I/Os pins interface
     */
    virtual void IoInit( void );

    /*!
     * @brief Initializes the radio SPI
     */
    virtual void SpiInit( void );

    /*!
     * @brief Initializes DIO IRQ handlers
     *
     * @param [IN] irqHandlers Array containing the IRQ callback functions
     */
    virtual void IoIrqInit( DioIrqHandler *irqHandlers );

    /*!
     * @brief De-initializes the radio I/Os pins interface. 
     *
     * \remark Useful when going in MCU lowpower modes
     */
    virtual void IoDeInit( void );

    /*!
     * @brief Gets the board PA selection configuration
     *
     * @param [IN] channel Channel frequency in Hz
     * @retval PaSelect RegPaConfig PaSelect value
     */
    virtual uint8_t GetPaSelect( uint32_t channel );

    /*!
     * @brief Set the RF Switch I/Os pins in Low Power mode
     *
     * @param [IN] status enable or disable
     */
    virtual void SetAntSwLowPower( bool status );

    /*!
     * @brief Initializes the RF Switch I/Os pins interface
     */
    virtual void AntSwInit( void );

    /*!
     * @brief De-initializes the RF Switch I/Os pins interface 
     *
     * @remark Needed to decrease the power consumption in MCU lowpower modes
     */
    virtual void AntSwDeInit( void );

    /*!
     * @brief Controls the antena switch if necessary.
     *
     * @remark see errata note
     *
     * @param [IN] opMode Current radio operating mode
     */
    virtual void SetAntSw( uint8_t opMode );
    
    /*
     * The the Timeout for a given Timer.
     */
	virtual void SetTimeout(TimeoutTimer_t timer, timeoutFuncPtr, int timeout_ms = 0);

    /*
     * A simple ms sleep
     */
    virtual void Sleep_ms(int ms);


public:
    
    /*!
     * @brief Detect the board connected by reading the value of the antenna switch pin
     */
	virtual uint8_t DetectBoardType( void );

    /*!
     * @brief Checks if the given RF frequency is supported by the hardware
     *
     * @param [IN] frequency RF frequency to be checked
     * @retval isSupported [true: supported, false: unsupported]
     */
    virtual bool CheckRfFrequency( uint32_t frequency );

    /*!
     * @brief Writes the radio register at the specified address
     *
     * @param [IN]: addr Register address
     * @param [IN]: data New register value
     */
    virtual void Write ( uint8_t addr, uint8_t data ) ;

    /*!
     * @brief Reads the radio register at the specified address
     *
     * @param [IN]: addr Register address
     * @retval data Register value
     */
    virtual uint8_t Read ( uint8_t addr ) ;

    /*!
     * @brief Writes multiple radio registers starting at address
     *
     * @param [IN] addr   First Radio register address
     * @param [IN] buffer Buffer containing the new register's values
     * @param [IN] size   Number of registers to be written
     */
    virtual void Write( uint8_t addr, void *buffer, uint8_t size ) ;

    /*!
     * @brief Reads multiple radio registers starting at address
     *
     * @param [IN] addr First Radio register address
     * @param [OUT] buffer Buffer where to copy the registers data
     * @param [IN] size Number of registers to be read
     */
    virtual void Read ( uint8_t addr, void *buffer, uint8_t size ) ;

    /*!
     * @brief Writes the buffer contents to the SX1276 FIFO
     *
     * @param [IN] buffer Buffer containing data to be put on the FIFO.
     * @param [IN] size Number of bytes to be written to the FIFO
     */
    virtual void WriteFifo( void *buffer, uint8_t size ) ;

    /*!
     * @brief Reads the contents of the SX1276 FIFO
     *
     * @param [OUT] buffer Buffer where to copy the FIFO read data.
     * @param [IN] size Number of bytes to be read from the FIFO
     */
    virtual void ReadFifo( void *buffer, uint8_t size ) ;

    /*!
     * @brief Reset the SX1276
     */
    virtual void Reset( void );
    
    /*!
     * \brief Sets the radio output power.
     *
     * @param [IN] power Sets the RF output power
     */
    virtual void SetRfTxPower( int8_t power );
    
};

#endif // __SX1276_MBED_HAL_H__