Shivanand Gowda
Serial Peripheral Interface (SPI) Serial Single IO NOR Flash Memory Interfacing 1Gb
Fork of
S25FL256S
by 
Shivanand Gowda
Diff: S25FL256S.h
- Revision:
- 6:b3c242976f7e
- Parent:
- 5:c2707c92ecb5
diff -r c2707c92ecb5 -r b3c242976f7e S25FL256S.h
--- a/S25FL256S.h Mon May 21 07:50:39 2018 +0000
+++ /dev/null Thu Jan 01 00:00:00 1970 +0000
@@ -1,144 +0,0 @@
-// S25FL256S.h
-
-#ifndef S25FL256S_H
-#define S25FL256S_H
-
-#include "mbed.h"
-#include <string>
-
-#define SPI_FREQ 5000000 //Change SPI Frequency Here
-#define SPI_MODE 0 // SPI Mode can be 0 or 3 . see data sheet
-#define SPI_NBIT 8 // Number of bits 8.
-
-
-
-#define DUMMY_ADDR 0x00
-#define WAIT_TIME 1
-
-#define ADDR_BMASK3 0xff000000
-#define ADDR_BMASK2 0x00ff0000
-#define ADDR_BMASK1 0x0000ff00
-#define ADDR_BMASK0 0x000000ff
-
-#define ADDR_BSHIFT3 24
-#define ADDR_BSHIFT2 16
-#define ADDR_BSHIFT1 8
-#define ADDR_BSHIFT0 0
-
-#define RDSR1 0x05 // 6th bit P_ERR Program Error-->1, NO error 0
- //5th bit E_ERR Program Error-->1, No ERROR 0
- //0th WIP --> 1 indicates Busy Writing, 0--> Free, Done
- // read Bits 6,5,0
-#define READ_ID 0x90 // Read Electronic Manufacturer Signature
-#define RDID 0x9F //Read ID (JEDEC Manufacturer ID and JEDEC CFI)
-#define RES 0xAB // Read Electronic Signature
-
-//4 Byte Address4PP 12h)
-
-#define FOUR_FAST_READ 0x0C //Read Fast (4-byte Address) 0C
-#define FOUR_READ 0x13 //Read (4-byte Address)
-#define FOUR_DOR 0x3C //Read Dual Out (FOUR_-byte Address) 3C
-#define FOUR_QOR 0x6C //Read Quad Out (FOUR_-byte Address)
-#define FOUR_DIOR 0xBC // Dual I/O Read (FOUR_-byte Address) BC
-#define FOUR_QIOR 0xEC //FOUR_QIOR Quad I/O Read (FOUR_-byte Address) EC
-#define FOUR_DDRFR 0x0E //Read DDR Fast (FOUR_-byte Address)
-#define FOUR_DDRDIOR 0xBE // DDR Dual I/O Read (FOUR_-byte Address) BE
-#define FOUR_DDRQIOR 0xEE
-#define FOUR_PP 0x12 // FOUR_PP Page Program (FOUR_-byte Address) 12
-#define FOUR_QPP 0x34 //Quad Page Program (FOUR_-byte Address)
-#define FOUR_P4E 0x21 // Parameter 4-kB Erase (4-byte Address) 21
-#define FOUR_SE 0xDC // Erase 64/256 kB (4-byte Address) DC
-
-//3 Byte Address
-
-#define READ 0x03 //READ Read (3-byte Address) 03
-#define FAST_READ 0x0B //FAST_READ Read Fast (3-byte Address) 0B
-#define DOR 0x3B //DOR Read Dual Out (3-byte Address) 3B
-#define Q0R 0x6B //QOR Read Quad Out (3-byte Address) 6B
-#define DIOR 0xBB //DIOR Dual I/O Read (3-byte Address) BB
-#define QIOR 0xEB //QIOR Quad I/O Read (3-byte Address) EB
-#define DDRFR 0x0D //DDRFR Read DDR Fast (3-byte Address) 0D
-#define DDRDIOR 0xBD //DDRDIOR DDR Dual I/O Read (3-byte Address) BD
-#define DDRQIOR 0xED //DDRQIOR DDR Quad I/O Read (3-byte Address) ED
-#define PP 0x02 //PP Page Program (3-byte Address) 02
-#define Qpp 0x32 //QPP Quad Page Program (3-byte Address) 32
-#define P4E 0x20 //P4E Parameter 4-kB Erase (3-byte Address) 20
-#define SE 0xD8 //SE Erase 64 / 256 kB (3-byte Address) D8
-#define BE 0x60 // Erase Entire Chip.
-
-#define RDSR1 0x05 //RDSR1 Read Status Register-1 05
-#define RDSR2 0x07 //RDSR2 Read Status Register-2 07
-#define RDCR 0x35 //RDCR Read Configuration Register-1 35
-#define WRR 0x01 //Write Register (Status-1, Configuration-1)
-#define WRDI 0x04 //Write Disable 04
-#define WREN 0x06 //WREN Write Enable 06
-#define CLSR 0x30 //CLSR Clear Status Register-1 - Erase/Prog. Fail Reset 30
-#define ECCRD 0x18 //ECCRD ECC Read (4-byte address) 18
-#define ABRD 0x14 //ABRD AutoBoot Register Read 14
-#define ABWR 0x15 //AutoBoot Register Write 15
-#define BRRD 0x16 //Bank Register Read 16
-#define BRWR 0x17 //Bank Register Write 17
-#define BRAC 0xB9 //BRAC Bank Register Access (Legacy Command formerly used for Deep Power Down) B9
-#define DLPRD 0x41 //DLPRD Data Learning Pattern Read 41
-#define PNVDLR 0x43 //PNVDLR Program NV Data Learning Register 43
-#define WVDLR 0x4A //Write Volatile Data Learning Register 4A
-#define PGSP 0x85 //Program Suspend 85
-#define PGRS 0x8A //Program Resume 8A
-#define ERSP 0x75 //Erase Suspend 75
-#define ERRS 0x7A //Erase Resume 7A
-#define OTPP 0x42 //OTP Program 42
-#define OTPR 0x4B //OTP Read 4B
-
-//Advanced Sector Protection
-
-#define DYBRD 0xE0 //DYB Read E0 133
-#define DYBWR 0xE1 //DYB Write E1 133
-#define PPBRD 0xE2 //PPB Read E2 133
-#define PPBP 0xE3 //PPB Program E3 133
-#define PPBE 0xE4 //PPB Erase E4 133
-#define ASPRD 0x2B //ASP Read 2B 133
-#define ASPP 0x2F //ASP Program 2F 133
-#define PLBRD 0xA7 //PPB Lock Bit Read A7 133
-#define PLBWR 0xA6 //PPB Lock Bit Write A6 133
-#define PASSRD 0xE7 //Password Read E7 133
-#define PASSP 0xE8 //Password Program E8 133
-#define PASSU 0xE9 //Password Unlock E9 133
-#define DUMMY 0x00 // Dummy write to read
-//Reset
-
-#define RESET 0xF0 //Software Reset F0 133
-#define MBR 0xFF //Mode Bit Reset FF 133
-#define DUMMYBYTE 0x00 //Dummy byte for Read Operation
-
-class S25FL256S: public SPI {
-public:
- S25FL256S(PinName mosi, PinName miso, PinName sclk, PinName cs);
-
- int readByte(int addr); // takes a 32-bit (4 bytes) address and returns the data (1 byte) at that location
- void readStream(int addr, char* buf, int count); // takes a 32-bit address, reads count bytes, and stores results in buf
-
- void writeByte(int addr, int data); // takes a 32-bit (4 bytes) address and a byte of data to write at that location
- void writeStream(int addr, char* buf, int count); // write count bytes of data from buf to memory, starting at addr
- void writeString(int add, string str);
- void sectorErase(int addr);
- void chipErase(); //erase all data on chip
- uint8_t readRegister();
- uint8_t checkIfBusy(); // Check if IC is bury writing or erasing
- void writeRegister(uint8_t regValue); // Write status register or configuration register
- void reset(void); // Reset Chip
- void clearRegister(); // Clear Status Register
- void Read_Identification(uint8_t *buf);
- long raedLong(int address); // Read long int number
- void writeLong(int addr, long value); // Write Long Integer Number
-private:
- void writeEnable(); // write enable
- void writeDisable(); // write disable
- void chipEnable(); // chip enable
- void chipDisable();
- // chip disable
-
- // SPI _spi;
- DigitalOut _cs;
-};
-
-#endif
\ No newline at end of file