mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of mbed-src by
targets/hal/TARGET_Freescale/TARGET_KPSDK_MCUS/TARGET_MCU_K64F/device/MK64F12/MK64F12_sdhc.h
- Committer:
- shaoziyang
- Date:
- 2014-09-13
- Revision:
- 323:9e901b0a5aa1
- Parent:
- 320:be04b2b1e3f2
File content as of revision 323:9e901b0a5aa1:
/* * Copyright (c) 2014, Freescale Semiconductor, Inc. * All rights reserved. * * THIS SOFTWARE IS PROVIDED BY FREESCALE "AS IS" AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT * SHALL FREESCALE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT * OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY * OF SUCH DAMAGE. */ /* * WARNING! DO NOT EDIT THIS FILE DIRECTLY! * * This file was generated automatically and any changes may be lost. */ #ifndef __HW_SDHC_REGISTERS_H__ #define __HW_SDHC_REGISTERS_H__ #include "regs.h" /* * MK64F12 SDHC * * Secured Digital Host Controller * * Registers defined in this header file: * - HW_SDHC_DSADDR - DMA System Address register * - HW_SDHC_BLKATTR - Block Attributes register * - HW_SDHC_CMDARG - Command Argument register * - HW_SDHC_XFERTYP - Transfer Type register * - HW_SDHC_CMDRSP0 - Command Response 0 * - HW_SDHC_CMDRSP1 - Command Response 1 * - HW_SDHC_CMDRSP2 - Command Response 2 * - HW_SDHC_CMDRSP3 - Command Response 3 * - HW_SDHC_DATPORT - Buffer Data Port register * - HW_SDHC_PRSSTAT - Present State register * - HW_SDHC_PROCTL - Protocol Control register * - HW_SDHC_SYSCTL - System Control register * - HW_SDHC_IRQSTAT - Interrupt Status register * - HW_SDHC_IRQSTATEN - Interrupt Status Enable register * - HW_SDHC_IRQSIGEN - Interrupt Signal Enable register * - HW_SDHC_AC12ERR - Auto CMD12 Error Status Register * - HW_SDHC_HTCAPBLT - Host Controller Capabilities * - HW_SDHC_WML - Watermark Level Register * - HW_SDHC_FEVT - Force Event register * - HW_SDHC_ADMAES - ADMA Error Status register * - HW_SDHC_ADSADDR - ADMA System Addressregister * - HW_SDHC_VENDOR - Vendor Specific register * - HW_SDHC_MMCBOOT - MMC Boot register * - HW_SDHC_HOSTVER - Host Controller Version * * - hw_sdhc_t - Struct containing all module registers. */ //! @name Module base addresses //@{ #ifndef REGS_SDHC_BASE #define HW_SDHC_INSTANCE_COUNT (1U) //!< Number of instances of the SDHC module. #define REGS_SDHC_BASE (0x400B1000U) //!< Base address for SDHC. #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_DSADDR - DMA System Address register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_DSADDR - DMA System Address register (RW) * * Reset value: 0x00000000U * * This register contains the physical system memory address used for DMA * transfers. */ typedef union _hw_sdhc_dsaddr { uint32_t U; struct _hw_sdhc_dsaddr_bitfields { uint32_t RESERVED0 : 2; //!< [1:0] uint32_t DSADDR : 30; //!< [31:2] DMA System Address } B; } hw_sdhc_dsaddr_t; #endif /*! * @name Constants and macros for entire SDHC_DSADDR register */ //@{ #define HW_SDHC_DSADDR_ADDR (REGS_SDHC_BASE + 0x0U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_DSADDR (*(__IO hw_sdhc_dsaddr_t *) HW_SDHC_DSADDR_ADDR) #define HW_SDHC_DSADDR_RD() (HW_SDHC_DSADDR.U) #define HW_SDHC_DSADDR_WR(v) (HW_SDHC_DSADDR.U = (v)) #define HW_SDHC_DSADDR_SET(v) (HW_SDHC_DSADDR_WR(HW_SDHC_DSADDR_RD() | (v))) #define HW_SDHC_DSADDR_CLR(v) (HW_SDHC_DSADDR_WR(HW_SDHC_DSADDR_RD() & ~(v))) #define HW_SDHC_DSADDR_TOG(v) (HW_SDHC_DSADDR_WR(HW_SDHC_DSADDR_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_DSADDR bitfields */ /*! * @name Register SDHC_DSADDR, field DSADDR[31:2] (RW) * * Contains the 32-bit system memory address for a DMA transfer. Because the * address must be word (4 bytes) align, the least 2 bits are reserved, always 0. * When the SDHC stops a DMA transfer, this register points to the system address * of the next contiguous data position. It can be accessed only when no * transaction is executing, that is, after a transaction has stopped. Read operation * during transfers may return an invalid value. The host driver shall initialize * this register before starting a DMA transaction. After DMA has stopped, the * system address of the next contiguous data position can be read from this register. * This register is protected during a data transfer. When data lines are * active, write to this register is ignored. The host driver shall wait, until * PRSSTAT[DLA] is cleared, before writing to this register. The SDHC internal DMA does * not support a virtual memory system. It supports only continuous physical * memory access. And due to AHB burst limitations, if the burst must cross the 1 KB * boundary, SDHC will automatically change SEQ burst type to NSEQ. Because this * register supports dynamic address reflecting, when IRQSTAT[TC] bit is set, it * automatically alters the value of internal address counter, so SW cannot * change this register when IRQSTAT[TC] is set. */ //@{ #define BP_SDHC_DSADDR_DSADDR (2U) //!< Bit position for SDHC_DSADDR_DSADDR. #define BM_SDHC_DSADDR_DSADDR (0xFFFFFFFCU) //!< Bit mask for SDHC_DSADDR_DSADDR. #define BS_SDHC_DSADDR_DSADDR (30U) //!< Bit field size in bits for SDHC_DSADDR_DSADDR. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_DSADDR_DSADDR field. #define BR_SDHC_DSADDR_DSADDR (HW_SDHC_DSADDR.B.DSADDR) #endif //! @brief Format value for bitfield SDHC_DSADDR_DSADDR. #define BF_SDHC_DSADDR_DSADDR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_DSADDR_DSADDR), uint32_t) & BM_SDHC_DSADDR_DSADDR) #ifndef __LANGUAGE_ASM__ //! @brief Set the DSADDR field to a new value. #define BW_SDHC_DSADDR_DSADDR(v) (HW_SDHC_DSADDR_WR((HW_SDHC_DSADDR_RD() & ~BM_SDHC_DSADDR_DSADDR) | BF_SDHC_DSADDR_DSADDR(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_BLKATTR - Block Attributes register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_BLKATTR - Block Attributes register (RW) * * Reset value: 0x00000000U * * This register is used to configure the number of data blocks and the number * of bytes in each block. */ typedef union _hw_sdhc_blkattr { uint32_t U; struct _hw_sdhc_blkattr_bitfields { uint32_t BLKSIZE : 13; //!< [12:0] Transfer Block Size uint32_t RESERVED0 : 3; //!< [15:13] uint32_t BLKCNT : 16; //!< [31:16] Blocks Count For Current Transfer } B; } hw_sdhc_blkattr_t; #endif /*! * @name Constants and macros for entire SDHC_BLKATTR register */ //@{ #define HW_SDHC_BLKATTR_ADDR (REGS_SDHC_BASE + 0x4U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_BLKATTR (*(__IO hw_sdhc_blkattr_t *) HW_SDHC_BLKATTR_ADDR) #define HW_SDHC_BLKATTR_RD() (HW_SDHC_BLKATTR.U) #define HW_SDHC_BLKATTR_WR(v) (HW_SDHC_BLKATTR.U = (v)) #define HW_SDHC_BLKATTR_SET(v) (HW_SDHC_BLKATTR_WR(HW_SDHC_BLKATTR_RD() | (v))) #define HW_SDHC_BLKATTR_CLR(v) (HW_SDHC_BLKATTR_WR(HW_SDHC_BLKATTR_RD() & ~(v))) #define HW_SDHC_BLKATTR_TOG(v) (HW_SDHC_BLKATTR_WR(HW_SDHC_BLKATTR_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_BLKATTR bitfields */ /*! * @name Register SDHC_BLKATTR, field BLKSIZE[12:0] (RW) * * Specifies the block size for block data transfers. Values ranging from 1 byte * up to the maximum buffer size can be set. It can be accessed only when no * transaction is executing, that is, after a transaction has stopped. Read * operations during transfers may return an invalid value, and write operations will be * ignored. * * Values: * - 0 - No data transfer. * - 1 - 1 Byte * - 10 - 2 Bytes * - 11 - 3 Bytes * - 100 - 4 Bytes * - 111111111 - 511 Bytes * - 1000000000 - 512 Bytes * - 100000000000 - 2048 Bytes * - 1000000000000 - 4096 Bytes */ //@{ #define BP_SDHC_BLKATTR_BLKSIZE (0U) //!< Bit position for SDHC_BLKATTR_BLKSIZE. #define BM_SDHC_BLKATTR_BLKSIZE (0x00001FFFU) //!< Bit mask for SDHC_BLKATTR_BLKSIZE. #define BS_SDHC_BLKATTR_BLKSIZE (13U) //!< Bit field size in bits for SDHC_BLKATTR_BLKSIZE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_BLKATTR_BLKSIZE field. #define BR_SDHC_BLKATTR_BLKSIZE (HW_SDHC_BLKATTR.B.BLKSIZE) #endif //! @brief Format value for bitfield SDHC_BLKATTR_BLKSIZE. #define BF_SDHC_BLKATTR_BLKSIZE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_BLKATTR_BLKSIZE), uint32_t) & BM_SDHC_BLKATTR_BLKSIZE) #ifndef __LANGUAGE_ASM__ //! @brief Set the BLKSIZE field to a new value. #define BW_SDHC_BLKATTR_BLKSIZE(v) (HW_SDHC_BLKATTR_WR((HW_SDHC_BLKATTR_RD() & ~BM_SDHC_BLKATTR_BLKSIZE) | BF_SDHC_BLKATTR_BLKSIZE(v))) #endif //@} /*! * @name Register SDHC_BLKATTR, field BLKCNT[31:16] (RW) * * This register is enabled when XFERTYP[BCEN] is set to 1 and is valid only for * multiple block transfers. For single block transfer, this register will * always read as 1. The host driver shall set this register to a value between 1 and * the maximum block count. The SDHC decrements the block count after each block * transfer and stops when the count reaches zero. Setting the block count to 0 * results in no data blocks being transferred. This register must be accessed * only when no transaction is executing, that is, after transactions are stopped. * During data transfer, read operations on this register may return an invalid * value and write operations are ignored. When saving transfer content as a result * of a suspend command, the number of blocks yet to be transferred can be * determined by reading this register. The reading of this register must be applied * after transfer is paused by stop at block gap operation and before sending the * command marked as suspend. This is because when suspend command is sent out, * SDHC will regard the current transfer as aborted and change BLKCNT back to its * original value instead of keeping the dynamical indicator of remained block * count. When restoring transfer content prior to issuing a resume command, the * host driver shall restore the previously saved block count. Although the BLKCNT * field is 0 after reset, the read of reset value is 0x1. This is because when * XFERTYP[MSBSEL] is 0, indicating a single block transfer, the read value of * BLKCNT is always 1. * * Values: * - 0 - Stop count. * - 1 - 1 block * - 10 - 2 blocks * - 1111111111111111 - 65535 blocks */ //@{ #define BP_SDHC_BLKATTR_BLKCNT (16U) //!< Bit position for SDHC_BLKATTR_BLKCNT. #define BM_SDHC_BLKATTR_BLKCNT (0xFFFF0000U) //!< Bit mask for SDHC_BLKATTR_BLKCNT. #define BS_SDHC_BLKATTR_BLKCNT (16U) //!< Bit field size in bits for SDHC_BLKATTR_BLKCNT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_BLKATTR_BLKCNT field. #define BR_SDHC_BLKATTR_BLKCNT (HW_SDHC_BLKATTR.B.BLKCNT) #endif //! @brief Format value for bitfield SDHC_BLKATTR_BLKCNT. #define BF_SDHC_BLKATTR_BLKCNT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_BLKATTR_BLKCNT), uint32_t) & BM_SDHC_BLKATTR_BLKCNT) #ifndef __LANGUAGE_ASM__ //! @brief Set the BLKCNT field to a new value. #define BW_SDHC_BLKATTR_BLKCNT(v) (HW_SDHC_BLKATTR_WR((HW_SDHC_BLKATTR_RD() & ~BM_SDHC_BLKATTR_BLKCNT) | BF_SDHC_BLKATTR_BLKCNT(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_CMDARG - Command Argument register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_CMDARG - Command Argument register (RW) * * Reset value: 0x00000000U * * This register contains the SD/MMC command argument. */ typedef union _hw_sdhc_cmdarg { uint32_t U; struct _hw_sdhc_cmdarg_bitfields { uint32_t CMDARG : 32; //!< [31:0] Command Argument } B; } hw_sdhc_cmdarg_t; #endif /*! * @name Constants and macros for entire SDHC_CMDARG register */ //@{ #define HW_SDHC_CMDARG_ADDR (REGS_SDHC_BASE + 0x8U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_CMDARG (*(__IO hw_sdhc_cmdarg_t *) HW_SDHC_CMDARG_ADDR) #define HW_SDHC_CMDARG_RD() (HW_SDHC_CMDARG.U) #define HW_SDHC_CMDARG_WR(v) (HW_SDHC_CMDARG.U = (v)) #define HW_SDHC_CMDARG_SET(v) (HW_SDHC_CMDARG_WR(HW_SDHC_CMDARG_RD() | (v))) #define HW_SDHC_CMDARG_CLR(v) (HW_SDHC_CMDARG_WR(HW_SDHC_CMDARG_RD() & ~(v))) #define HW_SDHC_CMDARG_TOG(v) (HW_SDHC_CMDARG_WR(HW_SDHC_CMDARG_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_CMDARG bitfields */ /*! * @name Register SDHC_CMDARG, field CMDARG[31:0] (RW) * * The SD/MMC command argument is specified as bits 39-8 of the command format * in the SD or MMC specification. This register is write protected when * PRSSTAT[CDIHB0] is set. */ //@{ #define BP_SDHC_CMDARG_CMDARG (0U) //!< Bit position for SDHC_CMDARG_CMDARG. #define BM_SDHC_CMDARG_CMDARG (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDARG_CMDARG. #define BS_SDHC_CMDARG_CMDARG (32U) //!< Bit field size in bits for SDHC_CMDARG_CMDARG. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_CMDARG_CMDARG field. #define BR_SDHC_CMDARG_CMDARG (HW_SDHC_CMDARG.U) #endif //! @brief Format value for bitfield SDHC_CMDARG_CMDARG. #define BF_SDHC_CMDARG_CMDARG(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_CMDARG_CMDARG), uint32_t) & BM_SDHC_CMDARG_CMDARG) #ifndef __LANGUAGE_ASM__ //! @brief Set the CMDARG field to a new value. #define BW_SDHC_CMDARG_CMDARG(v) (HW_SDHC_CMDARG_WR(v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_XFERTYP - Transfer Type register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_XFERTYP - Transfer Type register (RW) * * Reset value: 0x00000000U * * This register is used to control the operation of data transfers. The host * driver shall set this register before issuing a command followed by a data * transfer, or before issuing a resume command. To prevent data loss, the SDHC * prevents writing to the bits that are involved in the data transfer of this * register, when data transfer is active. These bits are DPSEL, MBSEL, DTDSEL, AC12EN, * BCEN, and DMAEN. The host driver shall check PRSSTAT[CDIHB] and PRSSTAT[CIHB] * before writing to this register. When PRSSTAT[CDIHB] is set, any attempt to * send a command with data by writing to this register is ignored; when * PRSSTAT[CIHB] bit is set, any write to this register is ignored. On sending commands with * data transfer involved, it is mandatory that the block size is nonzero. * Besides, block count must also be nonzero, or indicated as single block transfer * (bit 5 of this register is 0 when written), or block count is disabled (bit 1 of * this register is 0 when written), otherwise SDHC will ignore the sending of * this command and do nothing. For write command, with all above restrictions, it * is also mandatory that the write protect switch is not active (WPSPL bit of * Present State Register is 1), otherwise SDHC will also ignore the command. If * the commands with data transfer does not receive the response in 64 clock * cycles, that is, response time-out, SDHC will regard the external device does not * accept the command and abort the data transfer. In this scenario, the driver * must issue the command again to retry the transfer. It is also possible that, * for some reason, the card responds to the command but SDHC does not receive the * response, and if it is internal DMA (either simple DMA or ADMA) read * operation, the external system memory is over-written by the internal DMA with data * sent back from the card. The following table shows the summary of how register * settings determine the type of data transfer. Transfer Type register setting for * various transfer types Multi/Single block select Block count enable Block * count Function 0 Don't care Don't care Single transfer 1 0 Don't care Infinite * transfer 1 1 Positive number Multiple transfer 1 1 Zero No data transfer The * following table shows the relationship between XFERTYP[CICEN] and XFERTYP[CCCEN], * in regards to XFERTYP[RSPTYP] as well as the name of the response type. * Relationship between parameters and the name of the response type Response type * (RSPTYP) Index check enable (CICEN) CRC check enable (CCCEN) Name of response * type 00 0 0 No Response 01 0 1 IR2 10 0 0 R3,R4 10 1 1 R1,R5,R6 11 1 1 R1b,R5b In * the SDIO specification, response type notation for R5b is not defined. R5 * includes R5b in the SDIO specification. But R5b is defined in this specification * to specify that the SDHC will check the busy status after receiving a * response. For example, usually CMD52 is used with R5, but the I/O abort command shall * be used with R5b. The CRC field for R3 and R4 is expected to be all 1 bits. * The CRC check shall be disabled for these response types. */ typedef union _hw_sdhc_xfertyp { uint32_t U; struct _hw_sdhc_xfertyp_bitfields { uint32_t DMAEN : 1; //!< [0] DMA Enable uint32_t BCEN : 1; //!< [1] Block Count Enable uint32_t AC12EN : 1; //!< [2] Auto CMD12 Enable uint32_t RESERVED0 : 1; //!< [3] uint32_t DTDSEL : 1; //!< [4] Data Transfer Direction Select uint32_t MSBSEL : 1; //!< [5] Multi/Single Block Select uint32_t RESERVED1 : 10; //!< [15:6] uint32_t RSPTYP : 2; //!< [17:16] Response Type Select uint32_t RESERVED2 : 1; //!< [18] uint32_t CCCEN : 1; //!< [19] Command CRC Check Enable uint32_t CICEN : 1; //!< [20] Command Index Check Enable uint32_t DPSEL : 1; //!< [21] Data Present Select uint32_t CMDTYP : 2; //!< [23:22] Command Type uint32_t CMDINX : 6; //!< [29:24] Command Index uint32_t RESERVED3 : 2; //!< [31:30] } B; } hw_sdhc_xfertyp_t; #endif /*! * @name Constants and macros for entire SDHC_XFERTYP register */ //@{ #define HW_SDHC_XFERTYP_ADDR (REGS_SDHC_BASE + 0xCU) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_XFERTYP (*(__IO hw_sdhc_xfertyp_t *) HW_SDHC_XFERTYP_ADDR) #define HW_SDHC_XFERTYP_RD() (HW_SDHC_XFERTYP.U) #define HW_SDHC_XFERTYP_WR(v) (HW_SDHC_XFERTYP.U = (v)) #define HW_SDHC_XFERTYP_SET(v) (HW_SDHC_XFERTYP_WR(HW_SDHC_XFERTYP_RD() | (v))) #define HW_SDHC_XFERTYP_CLR(v) (HW_SDHC_XFERTYP_WR(HW_SDHC_XFERTYP_RD() & ~(v))) #define HW_SDHC_XFERTYP_TOG(v) (HW_SDHC_XFERTYP_WR(HW_SDHC_XFERTYP_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_XFERTYP bitfields */ /*! * @name Register SDHC_XFERTYP, field DMAEN[0] (RW) * * Enables DMA functionality. If this bit is set to 1, a DMA operation shall * begin when the host driver sets the DPSEL bit of this register. Whether the * simple DMA, or the advanced DMA, is active depends on PROCTL[DMAS]. * * Values: * - 0 - Disable * - 1 - Enable */ //@{ #define BP_SDHC_XFERTYP_DMAEN (0U) //!< Bit position for SDHC_XFERTYP_DMAEN. #define BM_SDHC_XFERTYP_DMAEN (0x00000001U) //!< Bit mask for SDHC_XFERTYP_DMAEN. #define BS_SDHC_XFERTYP_DMAEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_DMAEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_DMAEN field. #define BR_SDHC_XFERTYP_DMAEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DMAEN)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_DMAEN. #define BF_SDHC_XFERTYP_DMAEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_DMAEN), uint32_t) & BM_SDHC_XFERTYP_DMAEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DMAEN field to a new value. #define BW_SDHC_XFERTYP_DMAEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DMAEN) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field BCEN[1] (RW) * * Used to enable the Block Count register, which is only relevant for multiple * block transfers. When this bit is 0, the internal counter for block is * disabled, which is useful in executing an infinite transfer. * * Values: * - 0 - Disable * - 1 - Enable */ //@{ #define BP_SDHC_XFERTYP_BCEN (1U) //!< Bit position for SDHC_XFERTYP_BCEN. #define BM_SDHC_XFERTYP_BCEN (0x00000002U) //!< Bit mask for SDHC_XFERTYP_BCEN. #define BS_SDHC_XFERTYP_BCEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_BCEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_BCEN field. #define BR_SDHC_XFERTYP_BCEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_BCEN)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_BCEN. #define BF_SDHC_XFERTYP_BCEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_BCEN), uint32_t) & BM_SDHC_XFERTYP_BCEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BCEN field to a new value. #define BW_SDHC_XFERTYP_BCEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_BCEN) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field AC12EN[2] (RW) * * Multiple block transfers for memory require a CMD12 to stop the transaction. * When this bit is set to 1, the SDHC will issue a CMD12 automatically when the * last block transfer has completed. The host driver shall not set this bit to * issue commands that do not require CMD12 to stop a multiple block data * transfer. In particular, secure commands defined in File Security Specification (see * reference list) do not require CMD12. In single block transfer, the SDHC will * ignore this bit whether it is set or not. * * Values: * - 0 - Disable * - 1 - Enable */ //@{ #define BP_SDHC_XFERTYP_AC12EN (2U) //!< Bit position for SDHC_XFERTYP_AC12EN. #define BM_SDHC_XFERTYP_AC12EN (0x00000004U) //!< Bit mask for SDHC_XFERTYP_AC12EN. #define BS_SDHC_XFERTYP_AC12EN (1U) //!< Bit field size in bits for SDHC_XFERTYP_AC12EN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_AC12EN field. #define BR_SDHC_XFERTYP_AC12EN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_AC12EN)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_AC12EN. #define BF_SDHC_XFERTYP_AC12EN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_AC12EN), uint32_t) & BM_SDHC_XFERTYP_AC12EN) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12EN field to a new value. #define BW_SDHC_XFERTYP_AC12EN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_AC12EN) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field DTDSEL[4] (RW) * * Defines the direction of DAT line data transfers. The bit is set to 1 by the * host driver to transfer data from the SD card to the SDHC and is set to 0 for * all other commands. * * Values: * - 0 - Write host to card. * - 1 - Read card to host. */ //@{ #define BP_SDHC_XFERTYP_DTDSEL (4U) //!< Bit position for SDHC_XFERTYP_DTDSEL. #define BM_SDHC_XFERTYP_DTDSEL (0x00000010U) //!< Bit mask for SDHC_XFERTYP_DTDSEL. #define BS_SDHC_XFERTYP_DTDSEL (1U) //!< Bit field size in bits for SDHC_XFERTYP_DTDSEL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_DTDSEL field. #define BR_SDHC_XFERTYP_DTDSEL (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DTDSEL)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_DTDSEL. #define BF_SDHC_XFERTYP_DTDSEL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_DTDSEL), uint32_t) & BM_SDHC_XFERTYP_DTDSEL) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTDSEL field to a new value. #define BW_SDHC_XFERTYP_DTDSEL(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DTDSEL) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field MSBSEL[5] (RW) * * Enables multiple block DAT line data transfers. For any other commands, this * bit shall be set to 0. If this bit is 0, it is not necessary to set the block * count register. * * Values: * - 0 - Single block. * - 1 - Multiple blocks. */ //@{ #define BP_SDHC_XFERTYP_MSBSEL (5U) //!< Bit position for SDHC_XFERTYP_MSBSEL. #define BM_SDHC_XFERTYP_MSBSEL (0x00000020U) //!< Bit mask for SDHC_XFERTYP_MSBSEL. #define BS_SDHC_XFERTYP_MSBSEL (1U) //!< Bit field size in bits for SDHC_XFERTYP_MSBSEL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_MSBSEL field. #define BR_SDHC_XFERTYP_MSBSEL (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_MSBSEL)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_MSBSEL. #define BF_SDHC_XFERTYP_MSBSEL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_MSBSEL), uint32_t) & BM_SDHC_XFERTYP_MSBSEL) #ifndef __LANGUAGE_ASM__ //! @brief Set the MSBSEL field to a new value. #define BW_SDHC_XFERTYP_MSBSEL(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_MSBSEL) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field RSPTYP[17:16] (RW) * * Values: * - 00 - No response. * - 01 - Response length 136. * - 10 - Response length 48. * - 11 - Response length 48, check busy after response. */ //@{ #define BP_SDHC_XFERTYP_RSPTYP (16U) //!< Bit position for SDHC_XFERTYP_RSPTYP. #define BM_SDHC_XFERTYP_RSPTYP (0x00030000U) //!< Bit mask for SDHC_XFERTYP_RSPTYP. #define BS_SDHC_XFERTYP_RSPTYP (2U) //!< Bit field size in bits for SDHC_XFERTYP_RSPTYP. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_RSPTYP field. #define BR_SDHC_XFERTYP_RSPTYP (HW_SDHC_XFERTYP.B.RSPTYP) #endif //! @brief Format value for bitfield SDHC_XFERTYP_RSPTYP. #define BF_SDHC_XFERTYP_RSPTYP(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_RSPTYP), uint32_t) & BM_SDHC_XFERTYP_RSPTYP) #ifndef __LANGUAGE_ASM__ //! @brief Set the RSPTYP field to a new value. #define BW_SDHC_XFERTYP_RSPTYP(v) (HW_SDHC_XFERTYP_WR((HW_SDHC_XFERTYP_RD() & ~BM_SDHC_XFERTYP_RSPTYP) | BF_SDHC_XFERTYP_RSPTYP(v))) #endif //@} /*! * @name Register SDHC_XFERTYP, field CCCEN[19] (RW) * * If this bit is set to 1, the SDHC shall check the CRC field in the response. * If an error is detected, it is reported as a Command CRC Error. If this bit is * set to 0, the CRC field is not checked. The number of bits checked by the CRC * field value changes according to the length of the response. * * Values: * - 0 - Disable * - 1 - Enable */ //@{ #define BP_SDHC_XFERTYP_CCCEN (19U) //!< Bit position for SDHC_XFERTYP_CCCEN. #define BM_SDHC_XFERTYP_CCCEN (0x00080000U) //!< Bit mask for SDHC_XFERTYP_CCCEN. #define BS_SDHC_XFERTYP_CCCEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_CCCEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_CCCEN field. #define BR_SDHC_XFERTYP_CCCEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CCCEN)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_CCCEN. #define BF_SDHC_XFERTYP_CCCEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CCCEN), uint32_t) & BM_SDHC_XFERTYP_CCCEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CCCEN field to a new value. #define BW_SDHC_XFERTYP_CCCEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CCCEN) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field CICEN[20] (RW) * * If this bit is set to 1, the SDHC will check the index field in the response * to see if it has the same value as the command index. If it is not, it is * reported as a command index error. If this bit is set to 0, the index field is not * checked. * * Values: * - 0 - Disable * - 1 - Enable */ //@{ #define BP_SDHC_XFERTYP_CICEN (20U) //!< Bit position for SDHC_XFERTYP_CICEN. #define BM_SDHC_XFERTYP_CICEN (0x00100000U) //!< Bit mask for SDHC_XFERTYP_CICEN. #define BS_SDHC_XFERTYP_CICEN (1U) //!< Bit field size in bits for SDHC_XFERTYP_CICEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_CICEN field. #define BR_SDHC_XFERTYP_CICEN (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CICEN)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_CICEN. #define BF_SDHC_XFERTYP_CICEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CICEN), uint32_t) & BM_SDHC_XFERTYP_CICEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CICEN field to a new value. #define BW_SDHC_XFERTYP_CICEN(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_CICEN) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field DPSEL[21] (RW) * * This bit is set to 1 to indicate that data is present and shall be * transferred using the DAT line. It is set to 0 for the following: Commands using only * the CMD line, for example: CMD52. Commands with no data transfer, but using the * busy signal on DAT[0] line, R1b or R5b, for example: CMD38. In resume command, * this bit shall be set, and other bits in this register shall be set the same * as when the transfer was initially launched. When the Write Protect switch is * on, that is, the WPSPL bit is active as 0, any command with a write operation * will be ignored. That is to say, when this bit is set, while the DTDSEL bit is * 0, writes to the register Transfer Type are ignored. * * Values: * - 0 - No data present. * - 1 - Data present. */ //@{ #define BP_SDHC_XFERTYP_DPSEL (21U) //!< Bit position for SDHC_XFERTYP_DPSEL. #define BM_SDHC_XFERTYP_DPSEL (0x00200000U) //!< Bit mask for SDHC_XFERTYP_DPSEL. #define BS_SDHC_XFERTYP_DPSEL (1U) //!< Bit field size in bits for SDHC_XFERTYP_DPSEL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_DPSEL field. #define BR_SDHC_XFERTYP_DPSEL (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DPSEL)) #endif //! @brief Format value for bitfield SDHC_XFERTYP_DPSEL. #define BF_SDHC_XFERTYP_DPSEL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_DPSEL), uint32_t) & BM_SDHC_XFERTYP_DPSEL) #ifndef __LANGUAGE_ASM__ //! @brief Set the DPSEL field to a new value. #define BW_SDHC_XFERTYP_DPSEL(v) (BITBAND_ACCESS32(HW_SDHC_XFERTYP_ADDR, BP_SDHC_XFERTYP_DPSEL) = (v)) #endif //@} /*! * @name Register SDHC_XFERTYP, field CMDTYP[23:22] (RW) * * There are three types of special commands: suspend, resume, and abort. These * bits shall be set to 00b for all other commands. Suspend command: If the * suspend command succeeds, the SDHC shall assume that the card bus has been released * and that it is possible to issue the next command which uses the DAT line. * Because the SDHC does not monitor the content of command response, it does not * know if the suspend command succeeded or not. It is the host driver's * responsibility to check the status of the suspend command and send another command * marked as suspend to inform the SDHC that a suspend command was successfully * issued. After the end bit of command is sent, the SDHC deasserts read wait for read * transactions and stops checking busy for write transactions. In 4-bit mode, * the interrupt cycle starts. If the suspend command fails, the SDHC will * maintain its current state, and the host driver shall restart the transfer by setting * PROCTL[CREQ]. Resume command: The host driver restarts the data transfer by * restoring the registers saved before sending the suspend command and then sends * the resume command. The SDHC will check for a pending busy state before * starting write transfers. Abort command: If this command is set when executing a * read transfer, the SDHC will stop reads to the buffer. If this command is set * when executing a write transfer, the SDHC will stop driving the DAT line. After * issuing the abort command, the host driver must issue a software reset (abort * transaction). * * Values: * - 00 - Normal other commands. * - 01 - Suspend CMD52 for writing bus suspend in CCCR. * - 10 - Resume CMD52 for writing function select in CCCR. * - 11 - Abort CMD12, CMD52 for writing I/O abort in CCCR. */ //@{ #define BP_SDHC_XFERTYP_CMDTYP (22U) //!< Bit position for SDHC_XFERTYP_CMDTYP. #define BM_SDHC_XFERTYP_CMDTYP (0x00C00000U) //!< Bit mask for SDHC_XFERTYP_CMDTYP. #define BS_SDHC_XFERTYP_CMDTYP (2U) //!< Bit field size in bits for SDHC_XFERTYP_CMDTYP. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_CMDTYP field. #define BR_SDHC_XFERTYP_CMDTYP (HW_SDHC_XFERTYP.B.CMDTYP) #endif //! @brief Format value for bitfield SDHC_XFERTYP_CMDTYP. #define BF_SDHC_XFERTYP_CMDTYP(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CMDTYP), uint32_t) & BM_SDHC_XFERTYP_CMDTYP) #ifndef __LANGUAGE_ASM__ //! @brief Set the CMDTYP field to a new value. #define BW_SDHC_XFERTYP_CMDTYP(v) (HW_SDHC_XFERTYP_WR((HW_SDHC_XFERTYP_RD() & ~BM_SDHC_XFERTYP_CMDTYP) | BF_SDHC_XFERTYP_CMDTYP(v))) #endif //@} /*! * @name Register SDHC_XFERTYP, field CMDINX[29:24] (RW) * * These bits shall be set to the command number that is specified in bits 45-40 * of the command-format in the SD Memory Card Physical Layer Specification and * SDIO Card Specification. */ //@{ #define BP_SDHC_XFERTYP_CMDINX (24U) //!< Bit position for SDHC_XFERTYP_CMDINX. #define BM_SDHC_XFERTYP_CMDINX (0x3F000000U) //!< Bit mask for SDHC_XFERTYP_CMDINX. #define BS_SDHC_XFERTYP_CMDINX (6U) //!< Bit field size in bits for SDHC_XFERTYP_CMDINX. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_XFERTYP_CMDINX field. #define BR_SDHC_XFERTYP_CMDINX (HW_SDHC_XFERTYP.B.CMDINX) #endif //! @brief Format value for bitfield SDHC_XFERTYP_CMDINX. #define BF_SDHC_XFERTYP_CMDINX(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_XFERTYP_CMDINX), uint32_t) & BM_SDHC_XFERTYP_CMDINX) #ifndef __LANGUAGE_ASM__ //! @brief Set the CMDINX field to a new value. #define BW_SDHC_XFERTYP_CMDINX(v) (HW_SDHC_XFERTYP_WR((HW_SDHC_XFERTYP_RD() & ~BM_SDHC_XFERTYP_CMDINX) | BF_SDHC_XFERTYP_CMDINX(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_CMDRSP0 - Command Response 0 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_CMDRSP0 - Command Response 0 (RO) * * Reset value: 0x00000000U * * This register is used to store part 0 of the response bits from the card. */ typedef union _hw_sdhc_cmdrsp0 { uint32_t U; struct _hw_sdhc_cmdrsp0_bitfields { uint32_t CMDRSP0 : 32; //!< [31:0] Command Response 0 } B; } hw_sdhc_cmdrsp0_t; #endif /*! * @name Constants and macros for entire SDHC_CMDRSP0 register */ //@{ #define HW_SDHC_CMDRSP0_ADDR (REGS_SDHC_BASE + 0x10U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_CMDRSP0 (*(__I hw_sdhc_cmdrsp0_t *) HW_SDHC_CMDRSP0_ADDR) #define HW_SDHC_CMDRSP0_RD() (HW_SDHC_CMDRSP0.U) #endif //@} /* * Constants & macros for individual SDHC_CMDRSP0 bitfields */ /*! * @name Register SDHC_CMDRSP0, field CMDRSP0[31:0] (RO) */ //@{ #define BP_SDHC_CMDRSP0_CMDRSP0 (0U) //!< Bit position for SDHC_CMDRSP0_CMDRSP0. #define BM_SDHC_CMDRSP0_CMDRSP0 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP0_CMDRSP0. #define BS_SDHC_CMDRSP0_CMDRSP0 (32U) //!< Bit field size in bits for SDHC_CMDRSP0_CMDRSP0. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_CMDRSP0_CMDRSP0 field. #define BR_SDHC_CMDRSP0_CMDRSP0 (HW_SDHC_CMDRSP0.U) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_CMDRSP1 - Command Response 1 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_CMDRSP1 - Command Response 1 (RO) * * Reset value: 0x00000000U * * This register is used to store part 1 of the response bits from the card. */ typedef union _hw_sdhc_cmdrsp1 { uint32_t U; struct _hw_sdhc_cmdrsp1_bitfields { uint32_t CMDRSP1 : 32; //!< [31:0] Command Response 1 } B; } hw_sdhc_cmdrsp1_t; #endif /*! * @name Constants and macros for entire SDHC_CMDRSP1 register */ //@{ #define HW_SDHC_CMDRSP1_ADDR (REGS_SDHC_BASE + 0x14U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_CMDRSP1 (*(__I hw_sdhc_cmdrsp1_t *) HW_SDHC_CMDRSP1_ADDR) #define HW_SDHC_CMDRSP1_RD() (HW_SDHC_CMDRSP1.U) #endif //@} /* * Constants & macros for individual SDHC_CMDRSP1 bitfields */ /*! * @name Register SDHC_CMDRSP1, field CMDRSP1[31:0] (RO) */ //@{ #define BP_SDHC_CMDRSP1_CMDRSP1 (0U) //!< Bit position for SDHC_CMDRSP1_CMDRSP1. #define BM_SDHC_CMDRSP1_CMDRSP1 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP1_CMDRSP1. #define BS_SDHC_CMDRSP1_CMDRSP1 (32U) //!< Bit field size in bits for SDHC_CMDRSP1_CMDRSP1. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_CMDRSP1_CMDRSP1 field. #define BR_SDHC_CMDRSP1_CMDRSP1 (HW_SDHC_CMDRSP1.U) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_CMDRSP2 - Command Response 2 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_CMDRSP2 - Command Response 2 (RO) * * Reset value: 0x00000000U * * This register is used to store part 2 of the response bits from the card. */ typedef union _hw_sdhc_cmdrsp2 { uint32_t U; struct _hw_sdhc_cmdrsp2_bitfields { uint32_t CMDRSP2 : 32; //!< [31:0] Command Response 2 } B; } hw_sdhc_cmdrsp2_t; #endif /*! * @name Constants and macros for entire SDHC_CMDRSP2 register */ //@{ #define HW_SDHC_CMDRSP2_ADDR (REGS_SDHC_BASE + 0x18U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_CMDRSP2 (*(__I hw_sdhc_cmdrsp2_t *) HW_SDHC_CMDRSP2_ADDR) #define HW_SDHC_CMDRSP2_RD() (HW_SDHC_CMDRSP2.U) #endif //@} /* * Constants & macros for individual SDHC_CMDRSP2 bitfields */ /*! * @name Register SDHC_CMDRSP2, field CMDRSP2[31:0] (RO) */ //@{ #define BP_SDHC_CMDRSP2_CMDRSP2 (0U) //!< Bit position for SDHC_CMDRSP2_CMDRSP2. #define BM_SDHC_CMDRSP2_CMDRSP2 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP2_CMDRSP2. #define BS_SDHC_CMDRSP2_CMDRSP2 (32U) //!< Bit field size in bits for SDHC_CMDRSP2_CMDRSP2. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_CMDRSP2_CMDRSP2 field. #define BR_SDHC_CMDRSP2_CMDRSP2 (HW_SDHC_CMDRSP2.U) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_CMDRSP3 - Command Response 3 //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_CMDRSP3 - Command Response 3 (RO) * * Reset value: 0x00000000U * * This register is used to store part 3 of the response bits from the card. The * following table describes the mapping of command responses from the SD bus to * command response registers for each response type. In the table, R[ ] refers * to a bit range within the response data as transmitted on the SD bus. Response * bit definition for each response type Response type Meaning of response * Response field Response register R1,R1b (normal response) Card status R[39:8] * CMDRSP0 R1b (Auto CMD12 response) Card status for auto CMD12 R[39:8] CMDRSP3 R2 * (CID, CSD register) CID/CSD register [127:8] R[127:8] {CMDRSP3[23:0], CMDRSP2, * CMDRSP1, CMDRSP0} R3 (OCR register) OCR register for memory R[39:8] CMDRSP0 R4 * (OCR register) OCR register for I/O etc. R[39:8] CMDRSP0 R5, R5b SDIO response * R[39:8] CMDRSP0 R6 (Publish RCA) New published RCA[31:16] and card * status[15:0] R[39:9] CMDRSP0 This table shows that most responses with a length of 48 * (R[47:0]) have 32-bit of the response data (R[39:8]) stored in the CMDRSP0 * register. Responses of type R1b (auto CMD12 responses) have response data bits * (R[39:8]) stored in the CMDRSP3 register. Responses with length 136 (R[135:0]) have * 120-bit of the response data (R[127:8]) stored in the CMDRSP0, 1, 2, and 3 * registers. To be able to read the response status efficiently, the SDHC stores * only a part of the response data in the command response registers. This * enables the host driver to efficiently read 32-bit of response data in one read * cycle on a 32-bit bus system. Parts of the response, the index field and the CRC, * are checked by the SDHC, as specified by XFERTYP[CICEN] and XFERTYP[CCCEN], * and generate an error interrupt if any error is detected. The bit range for the * CRC check depends on the response length. If the response length is 48, the * SDHC will check R[47:1], and if the response length is 136 the SDHC will check * R[119:1]. Because the SDHC may have a multiple block data transfer executing * concurrently with a CMD_wo_DAT command, the SDHC stores the auto CMD12 response * in the CMDRSP3 register. The CMD_wo_DAT response is stored in CMDRSP0. This * allows the SDHC to avoid overwriting the Auto CMD12 response with the CMD_wo_DAT * and vice versa. When the SDHC modifies part of the command response * registers, as shown in the table above, it preserves the unmodified bits. */ typedef union _hw_sdhc_cmdrsp3 { uint32_t U; struct _hw_sdhc_cmdrsp3_bitfields { uint32_t CMDRSP3 : 32; //!< [31:0] Command Response 3 } B; } hw_sdhc_cmdrsp3_t; #endif /*! * @name Constants and macros for entire SDHC_CMDRSP3 register */ //@{ #define HW_SDHC_CMDRSP3_ADDR (REGS_SDHC_BASE + 0x1CU) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_CMDRSP3 (*(__I hw_sdhc_cmdrsp3_t *) HW_SDHC_CMDRSP3_ADDR) #define HW_SDHC_CMDRSP3_RD() (HW_SDHC_CMDRSP3.U) #endif //@} /* * Constants & macros for individual SDHC_CMDRSP3 bitfields */ /*! * @name Register SDHC_CMDRSP3, field CMDRSP3[31:0] (RO) */ //@{ #define BP_SDHC_CMDRSP3_CMDRSP3 (0U) //!< Bit position for SDHC_CMDRSP3_CMDRSP3. #define BM_SDHC_CMDRSP3_CMDRSP3 (0xFFFFFFFFU) //!< Bit mask for SDHC_CMDRSP3_CMDRSP3. #define BS_SDHC_CMDRSP3_CMDRSP3 (32U) //!< Bit field size in bits for SDHC_CMDRSP3_CMDRSP3. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_CMDRSP3_CMDRSP3 field. #define BR_SDHC_CMDRSP3_CMDRSP3 (HW_SDHC_CMDRSP3.U) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_DATPORT - Buffer Data Port register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_DATPORT - Buffer Data Port register (RW) * * Reset value: 0x00000000U * * This is a 32-bit data port register used to access the internal buffer and it * cannot be updated in Idle mode. */ typedef union _hw_sdhc_datport { uint32_t U; struct _hw_sdhc_datport_bitfields { uint32_t DATCONT : 32; //!< [31:0] Data Content } B; } hw_sdhc_datport_t; #endif /*! * @name Constants and macros for entire SDHC_DATPORT register */ //@{ #define HW_SDHC_DATPORT_ADDR (REGS_SDHC_BASE + 0x20U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_DATPORT (*(__IO hw_sdhc_datport_t *) HW_SDHC_DATPORT_ADDR) #define HW_SDHC_DATPORT_RD() (HW_SDHC_DATPORT.U) #define HW_SDHC_DATPORT_WR(v) (HW_SDHC_DATPORT.U = (v)) #define HW_SDHC_DATPORT_SET(v) (HW_SDHC_DATPORT_WR(HW_SDHC_DATPORT_RD() | (v))) #define HW_SDHC_DATPORT_CLR(v) (HW_SDHC_DATPORT_WR(HW_SDHC_DATPORT_RD() & ~(v))) #define HW_SDHC_DATPORT_TOG(v) (HW_SDHC_DATPORT_WR(HW_SDHC_DATPORT_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_DATPORT bitfields */ /*! * @name Register SDHC_DATPORT, field DATCONT[31:0] (RW) * * The Buffer Data Port register is for 32-bit data access by the CPU or the * external DMA. When the internal DMA is enabled, any write to this register is * ignored, and any read from this register will always yield 0s. */ //@{ #define BP_SDHC_DATPORT_DATCONT (0U) //!< Bit position for SDHC_DATPORT_DATCONT. #define BM_SDHC_DATPORT_DATCONT (0xFFFFFFFFU) //!< Bit mask for SDHC_DATPORT_DATCONT. #define BS_SDHC_DATPORT_DATCONT (32U) //!< Bit field size in bits for SDHC_DATPORT_DATCONT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_DATPORT_DATCONT field. #define BR_SDHC_DATPORT_DATCONT (HW_SDHC_DATPORT.U) #endif //! @brief Format value for bitfield SDHC_DATPORT_DATCONT. #define BF_SDHC_DATPORT_DATCONT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_DATPORT_DATCONT), uint32_t) & BM_SDHC_DATPORT_DATCONT) #ifndef __LANGUAGE_ASM__ //! @brief Set the DATCONT field to a new value. #define BW_SDHC_DATPORT_DATCONT(v) (HW_SDHC_DATPORT_WR(v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_PRSSTAT - Present State register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_PRSSTAT - Present State register (RO) * * Reset value: 0x00000000U * * The host driver can get status of the SDHC from this 32-bit read-only * register. The host driver can issue CMD0, CMD12, CMD13 (for memory) and CMD52 (for * SDIO) when the DAT lines are busy during a data transfer. These commands can be * issued when Command Inhibit (CIHB) is set to zero. Other commands shall be * issued when Command Inhibit (CDIHB) is set to zero. Possible changes to the SD * Physical Specification may add other commands to this list in the future. */ typedef union _hw_sdhc_prsstat { uint32_t U; struct _hw_sdhc_prsstat_bitfields { uint32_t CIHB : 1; //!< [0] Command Inhibit (CMD) uint32_t CDIHB : 1; //!< [1] Command Inhibit (DAT) uint32_t DLA : 1; //!< [2] Data Line Active uint32_t SDSTB : 1; //!< [3] SD Clock Stable uint32_t IPGOFF : 1; //!< [4] Bus Clock Gated Off Internally uint32_t HCKOFF : 1; //!< [5] System Clock Gated Off Internally uint32_t PEROFF : 1; //!< [6] SDHC clock Gated Off Internally uint32_t SDOFF : 1; //!< [7] SD Clock Gated Off Internally uint32_t WTA : 1; //!< [8] Write Transfer Active uint32_t RTA : 1; //!< [9] Read Transfer Active uint32_t BWEN : 1; //!< [10] Buffer Write Enable uint32_t BREN : 1; //!< [11] Buffer Read Enable uint32_t RESERVED0 : 4; //!< [15:12] uint32_t CINS : 1; //!< [16] Card Inserted uint32_t RESERVED1 : 6; //!< [22:17] uint32_t CLSL : 1; //!< [23] CMD Line Signal Level uint32_t DLSL : 8; //!< [31:24] DAT Line Signal Level } B; } hw_sdhc_prsstat_t; #endif /*! * @name Constants and macros for entire SDHC_PRSSTAT register */ //@{ #define HW_SDHC_PRSSTAT_ADDR (REGS_SDHC_BASE + 0x24U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_PRSSTAT (*(__I hw_sdhc_prsstat_t *) HW_SDHC_PRSSTAT_ADDR) #define HW_SDHC_PRSSTAT_RD() (HW_SDHC_PRSSTAT.U) #endif //@} /* * Constants & macros for individual SDHC_PRSSTAT bitfields */ /*! * @name Register SDHC_PRSSTAT, field CIHB[0] (RO) * * If this status bit is 0, it indicates that the CMD line is not in use and the * SDHC can issue a SD/MMC Command using the CMD line. This bit is set also * immediately after the Transfer Type register is written. This bit is cleared when * the command response is received. Even if the CDIHB bit is set to 1, Commands * using only the CMD line can be issued if this bit is 0. Changing from 1 to 0 * generates a command complete interrupt in the interrupt status register. If the * SDHC cannot issue the command because of a command conflict error (see * command CRC error) or because of a command not issued by auto CMD12 error, this bit * will remain 1 and the command complete is not set. The status of issuing an * auto CMD12 does not show on this bit. * * Values: * - 0 - Can issue command using only CMD line. * - 1 - Cannot issue command. */ //@{ #define BP_SDHC_PRSSTAT_CIHB (0U) //!< Bit position for SDHC_PRSSTAT_CIHB. #define BM_SDHC_PRSSTAT_CIHB (0x00000001U) //!< Bit mask for SDHC_PRSSTAT_CIHB. #define BS_SDHC_PRSSTAT_CIHB (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CIHB. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_CIHB field. #define BR_SDHC_PRSSTAT_CIHB (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CIHB)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field CDIHB[1] (RO) * * This status bit is generated if either the DLA or the RTA is set to 1. If * this bit is 0, it indicates that the SDHC can issue the next SD/MMC Command. * Commands with a busy signal belong to CDIHB, for example, R1b, R5b type. Except in * the case when the command busy is finished, changing from 1 to 0 generates a * transfer complete interrupt in the Interrupt Status register. The SD host * driver can save registers for a suspend transaction after this bit has changed * from 1 to 0. * * Values: * - 0 - Can issue command which uses the DAT line. * - 1 - Cannot issue command which uses the DAT line. */ //@{ #define BP_SDHC_PRSSTAT_CDIHB (1U) //!< Bit position for SDHC_PRSSTAT_CDIHB. #define BM_SDHC_PRSSTAT_CDIHB (0x00000002U) //!< Bit mask for SDHC_PRSSTAT_CDIHB. #define BS_SDHC_PRSSTAT_CDIHB (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CDIHB. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_CDIHB field. #define BR_SDHC_PRSSTAT_CDIHB (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CDIHB)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field DLA[2] (RO) * * Indicates whether one of the DAT lines on the SD bus is in use. In the case * of read transactions: This status indicates whether a read transfer is * executing on the SD bus. Changes in this value from 1 to 0, between data blocks, * generates a block gap event interrupt in the Interrupt Status register. This bit * will be set in either of the following cases: After the end bit of the read * command. When writing a 1 to PROCTL[CREQ] to restart a read transfer. This bit * will be cleared in either of the following cases: When the end bit of the last * data block is sent from the SD bus to the SDHC. When the read wait state is * stopped by a suspend command and the DAT2 line is released. The SDHC will wait at * the next block gap by driving read wait at the start of the interrupt cycle. * If the read wait signal is already driven (data buffer cannot receive data), * the SDHC can wait for a current block gap by continuing to drive the read wait * signal. It is necessary to support read wait to use the suspend / resume * function. This bit will remain 1 during read wait. In the case of write * transactions: This status indicates that a write transfer is executing on the SD bus. * Changes in this value from 1 to 0 generate a transfer complete interrupt in the * interrupt status register. This bit will be set in either of the following * cases: After the end bit of the write command. When writing to 1 to PROCTL[CREQ] to * continue a write transfer. This bit will be cleared in either of the * following cases: When the SD card releases write busy of the last data block, the SDHC * will also detect if the output is not busy. If the SD card does not drive the * busy signal after the CRC status is received, the SDHC shall assume the card * drive "Not busy". When the SD card releases write busy, prior to waiting for * write transfer, and as a result of a stop at block gap request. In the case of * command with busy pending: This status indicates that a busy state follows the * command and the data line is in use. This bit will be cleared when the DAT0 * line is released. * * Values: * - 0 - DAT line inactive. * - 1 - DAT line active. */ //@{ #define BP_SDHC_PRSSTAT_DLA (2U) //!< Bit position for SDHC_PRSSTAT_DLA. #define BM_SDHC_PRSSTAT_DLA (0x00000004U) //!< Bit mask for SDHC_PRSSTAT_DLA. #define BS_SDHC_PRSSTAT_DLA (1U) //!< Bit field size in bits for SDHC_PRSSTAT_DLA. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_DLA field. #define BR_SDHC_PRSSTAT_DLA (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_DLA)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field SDSTB[3] (RO) * * Indicates that the internal card clock is stable. This bit is for the host * driver to poll clock status when changing the clock frequency. It is recommended * to clear SYSCTL[SDCLKEN] to remove glitch on the card clock when the * frequency is changing. * * Values: * - 0 - Clock is changing frequency and not stable. * - 1 - Clock is stable. */ //@{ #define BP_SDHC_PRSSTAT_SDSTB (3U) //!< Bit position for SDHC_PRSSTAT_SDSTB. #define BM_SDHC_PRSSTAT_SDSTB (0x00000008U) //!< Bit mask for SDHC_PRSSTAT_SDSTB. #define BS_SDHC_PRSSTAT_SDSTB (1U) //!< Bit field size in bits for SDHC_PRSSTAT_SDSTB. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_SDSTB field. #define BR_SDHC_PRSSTAT_SDSTB (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_SDSTB)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field IPGOFF[4] (RO) * * Indicates that the bus clock is internally gated off. This bit is for the * host driver to debug. * * Values: * - 0 - Bus clock is active. * - 1 - Bus clock is gated off. */ //@{ #define BP_SDHC_PRSSTAT_IPGOFF (4U) //!< Bit position for SDHC_PRSSTAT_IPGOFF. #define BM_SDHC_PRSSTAT_IPGOFF (0x00000010U) //!< Bit mask for SDHC_PRSSTAT_IPGOFF. #define BS_SDHC_PRSSTAT_IPGOFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_IPGOFF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_IPGOFF field. #define BR_SDHC_PRSSTAT_IPGOFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_IPGOFF)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field HCKOFF[5] (RO) * * Indicates that the system clock is internally gated off. This bit is for the * host driver to debug during a data transfer. * * Values: * - 0 - System clock is active. * - 1 - System clock is gated off. */ //@{ #define BP_SDHC_PRSSTAT_HCKOFF (5U) //!< Bit position for SDHC_PRSSTAT_HCKOFF. #define BM_SDHC_PRSSTAT_HCKOFF (0x00000020U) //!< Bit mask for SDHC_PRSSTAT_HCKOFF. #define BS_SDHC_PRSSTAT_HCKOFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_HCKOFF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_HCKOFF field. #define BR_SDHC_PRSSTAT_HCKOFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_HCKOFF)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field PEROFF[6] (RO) * * Indicates that the is internally gated off. This bit is for the host driver * to debug transaction on the SD bus. When INITA bit is set, SDHC sending 80 * clock cycles to the card, SDCLKEN must be 1 to enable the output card clock, * otherwise the will never be gate off, so and will be always active. SDHC clock SDHC * clock SDHC clock bus clock * * Values: * - 0 - SDHC clock is active. * - 1 - SDHC clock is gated off. */ //@{ #define BP_SDHC_PRSSTAT_PEROFF (6U) //!< Bit position for SDHC_PRSSTAT_PEROFF. #define BM_SDHC_PRSSTAT_PEROFF (0x00000040U) //!< Bit mask for SDHC_PRSSTAT_PEROFF. #define BS_SDHC_PRSSTAT_PEROFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_PEROFF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_PEROFF field. #define BR_SDHC_PRSSTAT_PEROFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_PEROFF)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field SDOFF[7] (RO) * * Indicates that the SD clock is internally gated off, because of buffer * over/under-run or read pause without read wait assertion, or the driver has cleared * SYSCTL[SDCLKEN] to stop the SD clock. This bit is for the host driver to debug * data transaction on the SD bus. * * Values: * - 0 - SD clock is active. * - 1 - SD clock is gated off. */ //@{ #define BP_SDHC_PRSSTAT_SDOFF (7U) //!< Bit position for SDHC_PRSSTAT_SDOFF. #define BM_SDHC_PRSSTAT_SDOFF (0x00000080U) //!< Bit mask for SDHC_PRSSTAT_SDOFF. #define BS_SDHC_PRSSTAT_SDOFF (1U) //!< Bit field size in bits for SDHC_PRSSTAT_SDOFF. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_SDOFF field. #define BR_SDHC_PRSSTAT_SDOFF (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_SDOFF)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field WTA[8] (RO) * * Indicates that a write transfer is active. If this bit is 0, it means no * valid write data exists in the SDHC. This bit is set in either of the following * cases: After the end bit of the write command. When writing 1 to PROCTL[CREQ] to * restart a write transfer. This bit is cleared in either of the following * cases: After getting the CRC status of the last data block as specified by the * transfer count (single and multiple). After getting the CRC status of any block * where data transmission is about to be stopped by a stop at block gap request. * During a write transaction, a block gap event interrupt is generated when this * bit is changed to 0, as result of the stop at block gap request being set. * This status is useful for the host driver in determining when to issue commands * during write busy state. * * Values: * - 0 - No valid data. * - 1 - Transferring data. */ //@{ #define BP_SDHC_PRSSTAT_WTA (8U) //!< Bit position for SDHC_PRSSTAT_WTA. #define BM_SDHC_PRSSTAT_WTA (0x00000100U) //!< Bit mask for SDHC_PRSSTAT_WTA. #define BS_SDHC_PRSSTAT_WTA (1U) //!< Bit field size in bits for SDHC_PRSSTAT_WTA. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_WTA field. #define BR_SDHC_PRSSTAT_WTA (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_WTA)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field RTA[9] (RO) * * Used for detecting completion of a read transfer. This bit is set for either * of the following conditions: After the end bit of the read command. When * writing a 1 to PROCTL[CREQ] to restart a read transfer. A transfer complete * interrupt is generated when this bit changes to 0. This bit is cleared for either of * the following conditions: When the last data block as specified by block * length is transferred to the system, that is, all data are read away from SDHC * internal buffer. When all valid data blocks have been transferred from SDHC * internal buffer to the system and no current block transfers are being sent as a * result of the stop at block gap request being set to 1. * * Values: * - 0 - No valid data. * - 1 - Transferring data. */ //@{ #define BP_SDHC_PRSSTAT_RTA (9U) //!< Bit position for SDHC_PRSSTAT_RTA. #define BM_SDHC_PRSSTAT_RTA (0x00000200U) //!< Bit mask for SDHC_PRSSTAT_RTA. #define BS_SDHC_PRSSTAT_RTA (1U) //!< Bit field size in bits for SDHC_PRSSTAT_RTA. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_RTA field. #define BR_SDHC_PRSSTAT_RTA (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_RTA)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field BWEN[10] (RO) * * Used for non-DMA write transfers. The SDHC can implement multiple buffers to * transfer data efficiently. This read-only flag indicates whether space is * available for write data. If this bit is 1, valid data greater than the watermark * level can be written to the buffer. This read-only flag indicates whether * space is available for write data. * * Values: * - 0 - Write disable, the buffer can hold valid data less than the write * watermark level. * - 1 - Write enable, the buffer can hold valid data greater than the write * watermark level. */ //@{ #define BP_SDHC_PRSSTAT_BWEN (10U) //!< Bit position for SDHC_PRSSTAT_BWEN. #define BM_SDHC_PRSSTAT_BWEN (0x00000400U) //!< Bit mask for SDHC_PRSSTAT_BWEN. #define BS_SDHC_PRSSTAT_BWEN (1U) //!< Bit field size in bits for SDHC_PRSSTAT_BWEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_BWEN field. #define BR_SDHC_PRSSTAT_BWEN (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_BWEN)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field BREN[11] (RO) * * Used for non-DMA read transfers. The SDHC may implement multiple buffers to * transfer data efficiently. This read-only flag indicates that valid data exists * in the host side buffer. If this bit is high, valid data greater than the * watermark level exist in the buffer. This read-only flag indicates that valid * data exists in the host side buffer. * * Values: * - 0 - Read disable, valid data less than the watermark level exist in the * buffer. * - 1 - Read enable, valid data greater than the watermark level exist in the * buffer. */ //@{ #define BP_SDHC_PRSSTAT_BREN (11U) //!< Bit position for SDHC_PRSSTAT_BREN. #define BM_SDHC_PRSSTAT_BREN (0x00000800U) //!< Bit mask for SDHC_PRSSTAT_BREN. #define BS_SDHC_PRSSTAT_BREN (1U) //!< Bit field size in bits for SDHC_PRSSTAT_BREN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_BREN field. #define BR_SDHC_PRSSTAT_BREN (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_BREN)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field CINS[16] (RO) * * Indicates whether a card has been inserted. The SDHC debounces this signal so * that the host driver will not need to wait for it to stabilize. Changing from * a 0 to 1 generates a card insertion interrupt in the Interrupt Status * register. Changing from a 1 to 0 generates a card removal interrupt in the Interrupt * Status register. A write to the force event register does not effect this bit. * SYSCTL[RSTA] does not effect this bit. A software reset does not effect this * bit. * * Values: * - 0 - Power on reset or no card. * - 1 - Card inserted. */ //@{ #define BP_SDHC_PRSSTAT_CINS (16U) //!< Bit position for SDHC_PRSSTAT_CINS. #define BM_SDHC_PRSSTAT_CINS (0x00010000U) //!< Bit mask for SDHC_PRSSTAT_CINS. #define BS_SDHC_PRSSTAT_CINS (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CINS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_CINS field. #define BR_SDHC_PRSSTAT_CINS (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CINS)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field CLSL[23] (RO) * * Used to check the CMD line level to recover from errors, and for debugging. * The reset value is effected by the external pullup/pulldown resistor, by * default, the read value of this bit after reset is 1b, when the command line is * pulled up. */ //@{ #define BP_SDHC_PRSSTAT_CLSL (23U) //!< Bit position for SDHC_PRSSTAT_CLSL. #define BM_SDHC_PRSSTAT_CLSL (0x00800000U) //!< Bit mask for SDHC_PRSSTAT_CLSL. #define BS_SDHC_PRSSTAT_CLSL (1U) //!< Bit field size in bits for SDHC_PRSSTAT_CLSL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_CLSL field. #define BR_SDHC_PRSSTAT_CLSL (BITBAND_ACCESS32(HW_SDHC_PRSSTAT_ADDR, BP_SDHC_PRSSTAT_CLSL)) #endif //@} /*! * @name Register SDHC_PRSSTAT, field DLSL[31:24] (RO) * * Used to check the DAT line level to recover from errors, and for debugging. * This is especially useful in detecting the busy signal level from DAT[0]. The * reset value is effected by the external pullup/pulldown resistors. By default, * the read value of this field after reset is 8'b11110111, when DAT[3] is pulled * down and the other lines are pulled up. */ //@{ #define BP_SDHC_PRSSTAT_DLSL (24U) //!< Bit position for SDHC_PRSSTAT_DLSL. #define BM_SDHC_PRSSTAT_DLSL (0xFF000000U) //!< Bit mask for SDHC_PRSSTAT_DLSL. #define BS_SDHC_PRSSTAT_DLSL (8U) //!< Bit field size in bits for SDHC_PRSSTAT_DLSL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PRSSTAT_DLSL field. #define BR_SDHC_PRSSTAT_DLSL (HW_SDHC_PRSSTAT.B.DLSL) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_PROCTL - Protocol Control register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_PROCTL - Protocol Control register (RW) * * Reset value: 0x00000020U * * There are three cases to restart the transfer after stop at the block gap. * Which case is appropriate depends on whether the SDHC issues a suspend command * or the SD card accepts the suspend command: If the host driver does not issue a * suspend command, the continue request shall be used to restart the transfer. * If the host driver issues a suspend command and the SD card accepts it, a * resume command shall be used to restart the transfer. If the host driver issues a * suspend command and the SD card does not accept it, the continue request shall * be used to restart the transfer. Any time stop at block gap request stops the * data transfer, the host driver shall wait for a transfer complete (in the * interrupt status register), before attempting to restart the transfer. When * restarting the data transfer by continue request, the host driver shall clear the * stop at block gap request before or simultaneously. */ typedef union _hw_sdhc_proctl { uint32_t U; struct _hw_sdhc_proctl_bitfields { uint32_t LCTL : 1; //!< [0] LED Control uint32_t DTW : 2; //!< [2:1] Data Transfer Width uint32_t D3CD : 1; //!< [3] DAT3 As Card Detection Pin uint32_t EMODE : 2; //!< [5:4] Endian Mode uint32_t CDTL : 1; //!< [6] Card Detect Test Level uint32_t CDSS : 1; //!< [7] Card Detect Signal Selection uint32_t DMAS : 2; //!< [9:8] DMA Select uint32_t RESERVED0 : 6; //!< [15:10] uint32_t SABGREQ : 1; //!< [16] Stop At Block Gap Request uint32_t CREQ : 1; //!< [17] Continue Request uint32_t RWCTL : 1; //!< [18] Read Wait Control uint32_t IABG : 1; //!< [19] Interrupt At Block Gap uint32_t RESERVED1 : 4; //!< [23:20] uint32_t WECINT : 1; //!< [24] Wakeup Event Enable On Card Interrupt uint32_t WECINS : 1; //!< [25] Wakeup Event Enable On SD Card //! Insertion uint32_t WECRM : 1; //!< [26] Wakeup Event Enable On SD Card Removal uint32_t RESERVED2 : 5; //!< [31:27] } B; } hw_sdhc_proctl_t; #endif /*! * @name Constants and macros for entire SDHC_PROCTL register */ //@{ #define HW_SDHC_PROCTL_ADDR (REGS_SDHC_BASE + 0x28U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_PROCTL (*(__IO hw_sdhc_proctl_t *) HW_SDHC_PROCTL_ADDR) #define HW_SDHC_PROCTL_RD() (HW_SDHC_PROCTL.U) #define HW_SDHC_PROCTL_WR(v) (HW_SDHC_PROCTL.U = (v)) #define HW_SDHC_PROCTL_SET(v) (HW_SDHC_PROCTL_WR(HW_SDHC_PROCTL_RD() | (v))) #define HW_SDHC_PROCTL_CLR(v) (HW_SDHC_PROCTL_WR(HW_SDHC_PROCTL_RD() & ~(v))) #define HW_SDHC_PROCTL_TOG(v) (HW_SDHC_PROCTL_WR(HW_SDHC_PROCTL_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_PROCTL bitfields */ /*! * @name Register SDHC_PROCTL, field LCTL[0] (RW) * * This bit, fully controlled by the host driver, is used to caution the user * not to remove the card while the card is being accessed. If the software is * going to issue multiple SD commands, this bit can be set during all these * transactions. It is not necessary to change for each transaction. When the software * issues multiple SD commands, setting the bit once before the first command is * sufficient: it is not necessary to reset the bit between commands. * * Values: * - 0 - LED off. * - 1 - LED on. */ //@{ #define BP_SDHC_PROCTL_LCTL (0U) //!< Bit position for SDHC_PROCTL_LCTL. #define BM_SDHC_PROCTL_LCTL (0x00000001U) //!< Bit mask for SDHC_PROCTL_LCTL. #define BS_SDHC_PROCTL_LCTL (1U) //!< Bit field size in bits for SDHC_PROCTL_LCTL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_LCTL field. #define BR_SDHC_PROCTL_LCTL (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_LCTL)) #endif //! @brief Format value for bitfield SDHC_PROCTL_LCTL. #define BF_SDHC_PROCTL_LCTL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_LCTL), uint32_t) & BM_SDHC_PROCTL_LCTL) #ifndef __LANGUAGE_ASM__ //! @brief Set the LCTL field to a new value. #define BW_SDHC_PROCTL_LCTL(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_LCTL) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field DTW[2:1] (RW) * * Selects the data width of the SD bus for a data transfer. The host driver * shall set it to match the data width of the card. Possible data transfer width is * 1-bit, 4-bits or 8-bits. * * Values: * - 00 - 1-bit mode * - 01 - 4-bit mode * - 10 - 8-bit mode * - 11 - Reserved */ //@{ #define BP_SDHC_PROCTL_DTW (1U) //!< Bit position for SDHC_PROCTL_DTW. #define BM_SDHC_PROCTL_DTW (0x00000006U) //!< Bit mask for SDHC_PROCTL_DTW. #define BS_SDHC_PROCTL_DTW (2U) //!< Bit field size in bits for SDHC_PROCTL_DTW. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_DTW field. #define BR_SDHC_PROCTL_DTW (HW_SDHC_PROCTL.B.DTW) #endif //! @brief Format value for bitfield SDHC_PROCTL_DTW. #define BF_SDHC_PROCTL_DTW(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_DTW), uint32_t) & BM_SDHC_PROCTL_DTW) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTW field to a new value. #define BW_SDHC_PROCTL_DTW(v) (HW_SDHC_PROCTL_WR((HW_SDHC_PROCTL_RD() & ~BM_SDHC_PROCTL_DTW) | BF_SDHC_PROCTL_DTW(v))) #endif //@} /*! * @name Register SDHC_PROCTL, field D3CD[3] (RW) * * If this bit is set, DAT3 should be pulled down to act as a card detection * pin. Be cautious when using this feature, because DAT3 is also a chip-select for * the SPI mode. A pulldown on this pin and CMD0 may set the card into the SPI * mode, which the SDHC does not support. Note: Keep this bit set if SDIO interrupt * is used. * * Values: * - 0 - DAT3 does not monitor card Insertion. * - 1 - DAT3 as card detection pin. */ //@{ #define BP_SDHC_PROCTL_D3CD (3U) //!< Bit position for SDHC_PROCTL_D3CD. #define BM_SDHC_PROCTL_D3CD (0x00000008U) //!< Bit mask for SDHC_PROCTL_D3CD. #define BS_SDHC_PROCTL_D3CD (1U) //!< Bit field size in bits for SDHC_PROCTL_D3CD. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_D3CD field. #define BR_SDHC_PROCTL_D3CD (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_D3CD)) #endif //! @brief Format value for bitfield SDHC_PROCTL_D3CD. #define BF_SDHC_PROCTL_D3CD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_D3CD), uint32_t) & BM_SDHC_PROCTL_D3CD) #ifndef __LANGUAGE_ASM__ //! @brief Set the D3CD field to a new value. #define BW_SDHC_PROCTL_D3CD(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_D3CD) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field EMODE[5:4] (RW) * * The SDHC supports all four endian modes in data transfer. * * Values: * - 00 - Big endian mode * - 01 - Half word big endian mode * - 10 - Little endian mode * - 11 - Reserved */ //@{ #define BP_SDHC_PROCTL_EMODE (4U) //!< Bit position for SDHC_PROCTL_EMODE. #define BM_SDHC_PROCTL_EMODE (0x00000030U) //!< Bit mask for SDHC_PROCTL_EMODE. #define BS_SDHC_PROCTL_EMODE (2U) //!< Bit field size in bits for SDHC_PROCTL_EMODE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_EMODE field. #define BR_SDHC_PROCTL_EMODE (HW_SDHC_PROCTL.B.EMODE) #endif //! @brief Format value for bitfield SDHC_PROCTL_EMODE. #define BF_SDHC_PROCTL_EMODE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_EMODE), uint32_t) & BM_SDHC_PROCTL_EMODE) #ifndef __LANGUAGE_ASM__ //! @brief Set the EMODE field to a new value. #define BW_SDHC_PROCTL_EMODE(v) (HW_SDHC_PROCTL_WR((HW_SDHC_PROCTL_RD() & ~BM_SDHC_PROCTL_EMODE) | BF_SDHC_PROCTL_EMODE(v))) #endif //@} /*! * @name Register SDHC_PROCTL, field CDTL[6] (RW) * * Enabled while the CDSS is set to 1 and it indicates card insertion. * * Values: * - 0 - Card detect test level is 0, no card inserted. * - 1 - Card detect test level is 1, card inserted. */ //@{ #define BP_SDHC_PROCTL_CDTL (6U) //!< Bit position for SDHC_PROCTL_CDTL. #define BM_SDHC_PROCTL_CDTL (0x00000040U) //!< Bit mask for SDHC_PROCTL_CDTL. #define BS_SDHC_PROCTL_CDTL (1U) //!< Bit field size in bits for SDHC_PROCTL_CDTL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_CDTL field. #define BR_SDHC_PROCTL_CDTL (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDTL)) #endif //! @brief Format value for bitfield SDHC_PROCTL_CDTL. #define BF_SDHC_PROCTL_CDTL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_CDTL), uint32_t) & BM_SDHC_PROCTL_CDTL) #ifndef __LANGUAGE_ASM__ //! @brief Set the CDTL field to a new value. #define BW_SDHC_PROCTL_CDTL(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDTL) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field CDSS[7] (RW) * * Selects the source for the card detection. * * Values: * - 0 - Card detection level is selected for normal purpose. * - 1 - Card detection test level is selected for test purpose. */ //@{ #define BP_SDHC_PROCTL_CDSS (7U) //!< Bit position for SDHC_PROCTL_CDSS. #define BM_SDHC_PROCTL_CDSS (0x00000080U) //!< Bit mask for SDHC_PROCTL_CDSS. #define BS_SDHC_PROCTL_CDSS (1U) //!< Bit field size in bits for SDHC_PROCTL_CDSS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_CDSS field. #define BR_SDHC_PROCTL_CDSS (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDSS)) #endif //! @brief Format value for bitfield SDHC_PROCTL_CDSS. #define BF_SDHC_PROCTL_CDSS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_CDSS), uint32_t) & BM_SDHC_PROCTL_CDSS) #ifndef __LANGUAGE_ASM__ //! @brief Set the CDSS field to a new value. #define BW_SDHC_PROCTL_CDSS(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CDSS) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field DMAS[9:8] (RW) * * This field is valid while DMA (SDMA or ADMA) is enabled and selects the DMA * operation. * * Values: * - 00 - No DMA or simple DMA is selected. * - 01 - ADMA1 is selected. * - 10 - ADMA2 is selected. * - 11 - Reserved */ //@{ #define BP_SDHC_PROCTL_DMAS (8U) //!< Bit position for SDHC_PROCTL_DMAS. #define BM_SDHC_PROCTL_DMAS (0x00000300U) //!< Bit mask for SDHC_PROCTL_DMAS. #define BS_SDHC_PROCTL_DMAS (2U) //!< Bit field size in bits for SDHC_PROCTL_DMAS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_DMAS field. #define BR_SDHC_PROCTL_DMAS (HW_SDHC_PROCTL.B.DMAS) #endif //! @brief Format value for bitfield SDHC_PROCTL_DMAS. #define BF_SDHC_PROCTL_DMAS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_DMAS), uint32_t) & BM_SDHC_PROCTL_DMAS) #ifndef __LANGUAGE_ASM__ //! @brief Set the DMAS field to a new value. #define BW_SDHC_PROCTL_DMAS(v) (HW_SDHC_PROCTL_WR((HW_SDHC_PROCTL_RD() & ~BM_SDHC_PROCTL_DMAS) | BF_SDHC_PROCTL_DMAS(v))) #endif //@} /*! * @name Register SDHC_PROCTL, field SABGREQ[16] (RW) * * Used to stop executing a transaction at the next block gap for both DMA and * non-DMA transfers. Until the IRQSTATEN[TCSEN] is set to 1, indicating a * transfer completion, the host driver shall leave this bit set to 1. Clearing both * PROCTL[SABGREQ] and PROCTL[CREQ] does not cause the transaction to restart. Read * Wait is used to stop the read transaction at the block gap. The SDHC will * honor the PROCTL[SABGREQ] for write transfers, but for read transfers it requires * that SDIO card support read wait. Therefore, the host driver shall not set * this bit during read transfers unless the SDIO card supports read wait and has * set PROCTL[RWCTL] to 1, otherwise the SDHC will stop the SD bus clock to pause * the read operation during block gap. In the case of write transfers in which * the host driver writes data to the data port register, the host driver shall set * this bit after all block data is written. If this bit is set to 1, the host * driver shall not write data to the Data Port register after a block is sent. * Once this bit is set, the host driver shall not clear this bit before * IRQSTATEN[TCSEN] is set, otherwise the SDHC's behavior is undefined. This bit effects * PRSSTAT[RTA], PRSSTAT[WTA], and PRSSTAT[CDIHB]. * * Values: * - 0 - Transfer * - 1 - Stop */ //@{ #define BP_SDHC_PROCTL_SABGREQ (16U) //!< Bit position for SDHC_PROCTL_SABGREQ. #define BM_SDHC_PROCTL_SABGREQ (0x00010000U) //!< Bit mask for SDHC_PROCTL_SABGREQ. #define BS_SDHC_PROCTL_SABGREQ (1U) //!< Bit field size in bits for SDHC_PROCTL_SABGREQ. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_SABGREQ field. #define BR_SDHC_PROCTL_SABGREQ (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_SABGREQ)) #endif //! @brief Format value for bitfield SDHC_PROCTL_SABGREQ. #define BF_SDHC_PROCTL_SABGREQ(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_SABGREQ), uint32_t) & BM_SDHC_PROCTL_SABGREQ) #ifndef __LANGUAGE_ASM__ //! @brief Set the SABGREQ field to a new value. #define BW_SDHC_PROCTL_SABGREQ(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_SABGREQ) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field CREQ[17] (RW) * * Used to restart a transaction which was stopped using the PROCTL[SABGREQ]. * When a suspend operation is not accepted by the card, it is also by setting this * bit to restart the paused transfer. To cancel stop at the block gap, set * PROCTL[SABGREQ] to 0 and set this bit to 1 to restart the transfer. The SDHC * automatically clears this bit, therefore it is not necessary for the host driver to * set this bit to 0. If both PROCTL[SABGREQ] and this bit are 1, the continue * request is ignored. * * Values: * - 0 - No effect. * - 1 - Restart */ //@{ #define BP_SDHC_PROCTL_CREQ (17U) //!< Bit position for SDHC_PROCTL_CREQ. #define BM_SDHC_PROCTL_CREQ (0x00020000U) //!< Bit mask for SDHC_PROCTL_CREQ. #define BS_SDHC_PROCTL_CREQ (1U) //!< Bit field size in bits for SDHC_PROCTL_CREQ. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_CREQ field. #define BR_SDHC_PROCTL_CREQ (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CREQ)) #endif //! @brief Format value for bitfield SDHC_PROCTL_CREQ. #define BF_SDHC_PROCTL_CREQ(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_CREQ), uint32_t) & BM_SDHC_PROCTL_CREQ) #ifndef __LANGUAGE_ASM__ //! @brief Set the CREQ field to a new value. #define BW_SDHC_PROCTL_CREQ(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_CREQ) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field RWCTL[18] (RW) * * The read wait function is optional for SDIO cards. If the card supports read * wait, set this bit to enable use of the read wait protocol to stop read data * using the DAT[2] line. Otherwise, the SDHC has to stop the SD Clock to hold * read data, which restricts commands generation. When the host driver detects an * SDIO card insertion, it shall set this bit according to the CCCR of the card. * If the card does not support read wait, this bit shall never be set to 1, * otherwise DAT line conflicts may occur. If this bit is set to 0, stop at block gap * during read operation is also supported, but the SDHC will stop the SD Clock * to pause reading operation. * * Values: * - 0 - Disable read wait control, and stop SD clock at block gap when SABGREQ * is set. * - 1 - Enable read wait control, and assert read wait without stopping SD * clock at block gap when SABGREQ bit is set. */ //@{ #define BP_SDHC_PROCTL_RWCTL (18U) //!< Bit position for SDHC_PROCTL_RWCTL. #define BM_SDHC_PROCTL_RWCTL (0x00040000U) //!< Bit mask for SDHC_PROCTL_RWCTL. #define BS_SDHC_PROCTL_RWCTL (1U) //!< Bit field size in bits for SDHC_PROCTL_RWCTL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_RWCTL field. #define BR_SDHC_PROCTL_RWCTL (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_RWCTL)) #endif //! @brief Format value for bitfield SDHC_PROCTL_RWCTL. #define BF_SDHC_PROCTL_RWCTL(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_RWCTL), uint32_t) & BM_SDHC_PROCTL_RWCTL) #ifndef __LANGUAGE_ASM__ //! @brief Set the RWCTL field to a new value. #define BW_SDHC_PROCTL_RWCTL(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_RWCTL) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field IABG[19] (RW) * * Valid only in 4-bit mode, of the SDIO card, and selects a sample point in the * interrupt cycle. Setting to 1 enables interrupt detection at the block gap * for a multiple block transfer. Setting to 0 disables interrupt detection during * a multiple block transfer. If the SDIO card can't signal an interrupt during a * multiple block transfer, this bit must be set to 0 to avoid an inadvertent * interrupt. When the host driver detects an SDIO card insertion, it shall set * this bit according to the CCCR of the card. * * Values: * - 0 - Disabled * - 1 - Enabled */ //@{ #define BP_SDHC_PROCTL_IABG (19U) //!< Bit position for SDHC_PROCTL_IABG. #define BM_SDHC_PROCTL_IABG (0x00080000U) //!< Bit mask for SDHC_PROCTL_IABG. #define BS_SDHC_PROCTL_IABG (1U) //!< Bit field size in bits for SDHC_PROCTL_IABG. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_IABG field. #define BR_SDHC_PROCTL_IABG (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_IABG)) #endif //! @brief Format value for bitfield SDHC_PROCTL_IABG. #define BF_SDHC_PROCTL_IABG(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_IABG), uint32_t) & BM_SDHC_PROCTL_IABG) #ifndef __LANGUAGE_ASM__ //! @brief Set the IABG field to a new value. #define BW_SDHC_PROCTL_IABG(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_IABG) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field WECINT[24] (RW) * * Enables a wakeup event, via IRQSTAT[CINT]. This bit can be set to 1 if FN_WUS * (Wake Up Support) in CIS is set to 1. When this bit is set, the card * interrupt status and the SDHC interrupt can be asserted without SD_CLK toggling. When * the wakeup feature is not enabled, the SD_CLK must be active to assert the * card interrupt status and the SDHC interrupt. * * Values: * - 0 - Disabled * - 1 - Enabled */ //@{ #define BP_SDHC_PROCTL_WECINT (24U) //!< Bit position for SDHC_PROCTL_WECINT. #define BM_SDHC_PROCTL_WECINT (0x01000000U) //!< Bit mask for SDHC_PROCTL_WECINT. #define BS_SDHC_PROCTL_WECINT (1U) //!< Bit field size in bits for SDHC_PROCTL_WECINT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_WECINT field. #define BR_SDHC_PROCTL_WECINT (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINT)) #endif //! @brief Format value for bitfield SDHC_PROCTL_WECINT. #define BF_SDHC_PROCTL_WECINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_WECINT), uint32_t) & BM_SDHC_PROCTL_WECINT) #ifndef __LANGUAGE_ASM__ //! @brief Set the WECINT field to a new value. #define BW_SDHC_PROCTL_WECINT(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINT) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field WECINS[25] (RW) * * Enables a wakeup event, via IRQSTAT[CINS]. FN_WUS (Wake Up Support) in CIS * does not effect this bit. When this bit is set, IRQSTATEN[CINSEN] and the SDHC * interrupt can be asserted without SD_CLK toggling. When the wakeup feature is * not enabled, the SD_CLK must be active to assert IRQSTATEN[CINSEN] and the SDHC * interrupt. * * Values: * - 0 - Disabled * - 1 - Enabled */ //@{ #define BP_SDHC_PROCTL_WECINS (25U) //!< Bit position for SDHC_PROCTL_WECINS. #define BM_SDHC_PROCTL_WECINS (0x02000000U) //!< Bit mask for SDHC_PROCTL_WECINS. #define BS_SDHC_PROCTL_WECINS (1U) //!< Bit field size in bits for SDHC_PROCTL_WECINS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_WECINS field. #define BR_SDHC_PROCTL_WECINS (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINS)) #endif //! @brief Format value for bitfield SDHC_PROCTL_WECINS. #define BF_SDHC_PROCTL_WECINS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_WECINS), uint32_t) & BM_SDHC_PROCTL_WECINS) #ifndef __LANGUAGE_ASM__ //! @brief Set the WECINS field to a new value. #define BW_SDHC_PROCTL_WECINS(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECINS) = (v)) #endif //@} /*! * @name Register SDHC_PROCTL, field WECRM[26] (RW) * * Enables a wakeup event, via IRQSTAT[CRM]. FN_WUS (Wake Up Support) in CIS * does not effect this bit. When this bit is set, IRQSTAT[CRM] and the SDHC * interrupt can be asserted without SD_CLK toggling. When the wakeup feature is not * enabled, the SD_CLK must be active to assert IRQSTAT[CRM] and the SDHC interrupt. * * Values: * - 0 - Disabled * - 1 - Enabled */ //@{ #define BP_SDHC_PROCTL_WECRM (26U) //!< Bit position for SDHC_PROCTL_WECRM. #define BM_SDHC_PROCTL_WECRM (0x04000000U) //!< Bit mask for SDHC_PROCTL_WECRM. #define BS_SDHC_PROCTL_WECRM (1U) //!< Bit field size in bits for SDHC_PROCTL_WECRM. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_PROCTL_WECRM field. #define BR_SDHC_PROCTL_WECRM (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECRM)) #endif //! @brief Format value for bitfield SDHC_PROCTL_WECRM. #define BF_SDHC_PROCTL_WECRM(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_PROCTL_WECRM), uint32_t) & BM_SDHC_PROCTL_WECRM) #ifndef __LANGUAGE_ASM__ //! @brief Set the WECRM field to a new value. #define BW_SDHC_PROCTL_WECRM(v) (BITBAND_ACCESS32(HW_SDHC_PROCTL_ADDR, BP_SDHC_PROCTL_WECRM) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_SYSCTL - System Control register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_SYSCTL - System Control register (RW) * * Reset value: 0x00008008U */ typedef union _hw_sdhc_sysctl { uint32_t U; struct _hw_sdhc_sysctl_bitfields { uint32_t IPGEN : 1; //!< [0] IPG Clock Enable uint32_t HCKEN : 1; //!< [1] System Clock Enable uint32_t PEREN : 1; //!< [2] Peripheral Clock Enable uint32_t SDCLKEN : 1; //!< [3] SD Clock Enable uint32_t DVS : 4; //!< [7:4] Divisor uint32_t SDCLKFS : 8; //!< [15:8] SDCLK Frequency Select uint32_t DTOCV : 4; //!< [19:16] Data Timeout Counter Value uint32_t RESERVED0 : 4; //!< [23:20] uint32_t RSTA : 1; //!< [24] Software Reset For ALL uint32_t RSTC : 1; //!< [25] Software Reset For CMD Line uint32_t RSTD : 1; //!< [26] Software Reset For DAT Line uint32_t INITA : 1; //!< [27] Initialization Active uint32_t RESERVED1 : 4; //!< [31:28] } B; } hw_sdhc_sysctl_t; #endif /*! * @name Constants and macros for entire SDHC_SYSCTL register */ //@{ #define HW_SDHC_SYSCTL_ADDR (REGS_SDHC_BASE + 0x2CU) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_SYSCTL (*(__IO hw_sdhc_sysctl_t *) HW_SDHC_SYSCTL_ADDR) #define HW_SDHC_SYSCTL_RD() (HW_SDHC_SYSCTL.U) #define HW_SDHC_SYSCTL_WR(v) (HW_SDHC_SYSCTL.U = (v)) #define HW_SDHC_SYSCTL_SET(v) (HW_SDHC_SYSCTL_WR(HW_SDHC_SYSCTL_RD() | (v))) #define HW_SDHC_SYSCTL_CLR(v) (HW_SDHC_SYSCTL_WR(HW_SDHC_SYSCTL_RD() & ~(v))) #define HW_SDHC_SYSCTL_TOG(v) (HW_SDHC_SYSCTL_WR(HW_SDHC_SYSCTL_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_SYSCTL bitfields */ /*! * @name Register SDHC_SYSCTL, field IPGEN[0] (RW) * * If this bit is set, bus clock will always be active and no automatic gating * is applied. The bus clock will be internally gated off, if none of the * following factors are met: The cmd part is reset, or Data part is reset, or Soft * reset, or The cmd is about to send, or Clock divisor is just updated, or Continue * request is just set, or This bit is set, or Card insertion is detected, or Card * removal is detected, or Card external interrupt is detected, or The SDHC * clock is not gated off The bus clock will not be auto gated off if the SDHC clock * is not gated off. So clearing only this bit has no effect unless the PEREN bit * is also cleared. * * Values: * - 0 - Bus clock will be internally gated off. * - 1 - Bus clock will not be automatically gated off. */ //@{ #define BP_SDHC_SYSCTL_IPGEN (0U) //!< Bit position for SDHC_SYSCTL_IPGEN. #define BM_SDHC_SYSCTL_IPGEN (0x00000001U) //!< Bit mask for SDHC_SYSCTL_IPGEN. #define BS_SDHC_SYSCTL_IPGEN (1U) //!< Bit field size in bits for SDHC_SYSCTL_IPGEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_IPGEN field. #define BR_SDHC_SYSCTL_IPGEN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_IPGEN)) #endif //! @brief Format value for bitfield SDHC_SYSCTL_IPGEN. #define BF_SDHC_SYSCTL_IPGEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_IPGEN), uint32_t) & BM_SDHC_SYSCTL_IPGEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the IPGEN field to a new value. #define BW_SDHC_SYSCTL_IPGEN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_IPGEN) = (v)) #endif //@} /*! * @name Register SDHC_SYSCTL, field HCKEN[1] (RW) * * If this bit is set, system clock will always be active and no automatic * gating is applied. When this bit is cleared, system clock will be automatically off * when no data transfer is on the SD bus. * * Values: * - 0 - System clock will be internally gated off. * - 1 - System clock will not be automatically gated off. */ //@{ #define BP_SDHC_SYSCTL_HCKEN (1U) //!< Bit position for SDHC_SYSCTL_HCKEN. #define BM_SDHC_SYSCTL_HCKEN (0x00000002U) //!< Bit mask for SDHC_SYSCTL_HCKEN. #define BS_SDHC_SYSCTL_HCKEN (1U) //!< Bit field size in bits for SDHC_SYSCTL_HCKEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_HCKEN field. #define BR_SDHC_SYSCTL_HCKEN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_HCKEN)) #endif //! @brief Format value for bitfield SDHC_SYSCTL_HCKEN. #define BF_SDHC_SYSCTL_HCKEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_HCKEN), uint32_t) & BM_SDHC_SYSCTL_HCKEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the HCKEN field to a new value. #define BW_SDHC_SYSCTL_HCKEN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_HCKEN) = (v)) #endif //@} /*! * @name Register SDHC_SYSCTL, field PEREN[2] (RW) * * If this bit is set, SDHC clock will always be active and no automatic gating * is applied. Thus the SDCLK is active except for when auto gating-off during * buffer danger (buffer about to over-run or under-run). When this bit is cleared, * the SDHC clock will be automatically off whenever there is no transaction on * the SD bus. Because this bit is only a feature enabling bit, clearing this bit * does not stop SDCLK immediately. The SDHC clock will be internally gated off, * if none of the following factors are met: The cmd part is reset, or Data part * is reset, or A soft reset, or The cmd is about to send, or Clock divisor is * just updated, or Continue request is just set, or This bit is set, or Card * insertion is detected, or Card removal is detected, or Card external interrupt is * detected, or 80 clocks for initialization phase is ongoing * * Values: * - 0 - SDHC clock will be internally gated off. * - 1 - SDHC clock will not be automatically gated off. */ //@{ #define BP_SDHC_SYSCTL_PEREN (2U) //!< Bit position for SDHC_SYSCTL_PEREN. #define BM_SDHC_SYSCTL_PEREN (0x00000004U) //!< Bit mask for SDHC_SYSCTL_PEREN. #define BS_SDHC_SYSCTL_PEREN (1U) //!< Bit field size in bits for SDHC_SYSCTL_PEREN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_PEREN field. #define BR_SDHC_SYSCTL_PEREN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_PEREN)) #endif //! @brief Format value for bitfield SDHC_SYSCTL_PEREN. #define BF_SDHC_SYSCTL_PEREN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_PEREN), uint32_t) & BM_SDHC_SYSCTL_PEREN) #ifndef __LANGUAGE_ASM__ //! @brief Set the PEREN field to a new value. #define BW_SDHC_SYSCTL_PEREN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_PEREN) = (v)) #endif //@} /*! * @name Register SDHC_SYSCTL, field SDCLKEN[3] (RW) * * The host controller shall stop SDCLK when writing this bit to 0. SDCLK * frequency can be changed when this bit is 0. Then, the host controller shall * maintain the same clock frequency until SDCLK is stopped (stop at SDCLK = 0). If the * IRQSTAT[CINS] is cleared, this bit must be cleared by the host driver to save * power. */ //@{ #define BP_SDHC_SYSCTL_SDCLKEN (3U) //!< Bit position for SDHC_SYSCTL_SDCLKEN. #define BM_SDHC_SYSCTL_SDCLKEN (0x00000008U) //!< Bit mask for SDHC_SYSCTL_SDCLKEN. #define BS_SDHC_SYSCTL_SDCLKEN (1U) //!< Bit field size in bits for SDHC_SYSCTL_SDCLKEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_SDCLKEN field. #define BR_SDHC_SYSCTL_SDCLKEN (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_SDCLKEN)) #endif //! @brief Format value for bitfield SDHC_SYSCTL_SDCLKEN. #define BF_SDHC_SYSCTL_SDCLKEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_SDCLKEN), uint32_t) & BM_SDHC_SYSCTL_SDCLKEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the SDCLKEN field to a new value. #define BW_SDHC_SYSCTL_SDCLKEN(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_SDCLKEN) = (v)) #endif //@} /*! * @name Register SDHC_SYSCTL, field DVS[7:4] (RW) * * Used to provide a more exact divisor to generate the desired SD clock * frequency. Note the divider can even support odd divisor without deterioration of * duty cycle. The setting are as following: * * Values: * - 0 - Divisor by 1. * - 1 - Divisor by 2. * - 1110 - Divisor by 15. * - 1111 - Divisor by 16. */ //@{ #define BP_SDHC_SYSCTL_DVS (4U) //!< Bit position for SDHC_SYSCTL_DVS. #define BM_SDHC_SYSCTL_DVS (0x000000F0U) //!< Bit mask for SDHC_SYSCTL_DVS. #define BS_SDHC_SYSCTL_DVS (4U) //!< Bit field size in bits for SDHC_SYSCTL_DVS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_DVS field. #define BR_SDHC_SYSCTL_DVS (HW_SDHC_SYSCTL.B.DVS) #endif //! @brief Format value for bitfield SDHC_SYSCTL_DVS. #define BF_SDHC_SYSCTL_DVS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_DVS), uint32_t) & BM_SDHC_SYSCTL_DVS) #ifndef __LANGUAGE_ASM__ //! @brief Set the DVS field to a new value. #define BW_SDHC_SYSCTL_DVS(v) (HW_SDHC_SYSCTL_WR((HW_SDHC_SYSCTL_RD() & ~BM_SDHC_SYSCTL_DVS) | BF_SDHC_SYSCTL_DVS(v))) #endif //@} /*! * @name Register SDHC_SYSCTL, field SDCLKFS[15:8] (RW) * * Used to select the frequency of the SDCLK pin. The frequency is not * programmed directly. Rather this register holds the prescaler (this register) and * divisor (next register) of the base clock frequency register. Setting 00h bypasses * the frequency prescaler of the SD Clock. Multiple bits must not be set, or the * behavior of this prescaler is undefined. The two default divider values can * be calculated by the frequency of SDHC clock and the following divisor bits. * The frequency of SDCLK is set by the following formula: Clock frequency = (Base * clock) / (prescaler x divisor) For example, if the base clock frequency is 96 * MHz, and the target frequency is 25 MHz, then choosing the prescaler value of * 01h and divisor value of 1h will yield 24 MHz, which is the nearest frequency * less than or equal to the target. Similarly, to approach a clock value of 400 * kHz, the prescaler value of 08h and divisor value of eh yields the exact clock * value of 400 kHz. The reset value of this field is 80h, so if the input base * clock ( SDHC clock ) is about 96 MHz, the default SD clock after reset is 375 * kHz. According to the SD Physical Specification Version 1.1 and the SDIO Card * Specification Version 1.2, the maximum SD clock frequency is 50 MHz and shall * never exceed this limit. Only the following settings are allowed: * * Values: * - 1 - Base clock divided by 2. * - 10 - Base clock divided by 4. * - 100 - Base clock divided by 8. * - 1000 - Base clock divided by 16. * - 10000 - Base clock divided by 32. * - 100000 - Base clock divided by 64. * - 1000000 - Base clock divided by 128. * - 10000000 - Base clock divided by 256. */ //@{ #define BP_SDHC_SYSCTL_SDCLKFS (8U) //!< Bit position for SDHC_SYSCTL_SDCLKFS. #define BM_SDHC_SYSCTL_SDCLKFS (0x0000FF00U) //!< Bit mask for SDHC_SYSCTL_SDCLKFS. #define BS_SDHC_SYSCTL_SDCLKFS (8U) //!< Bit field size in bits for SDHC_SYSCTL_SDCLKFS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_SDCLKFS field. #define BR_SDHC_SYSCTL_SDCLKFS (HW_SDHC_SYSCTL.B.SDCLKFS) #endif //! @brief Format value for bitfield SDHC_SYSCTL_SDCLKFS. #define BF_SDHC_SYSCTL_SDCLKFS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_SDCLKFS), uint32_t) & BM_SDHC_SYSCTL_SDCLKFS) #ifndef __LANGUAGE_ASM__ //! @brief Set the SDCLKFS field to a new value. #define BW_SDHC_SYSCTL_SDCLKFS(v) (HW_SDHC_SYSCTL_WR((HW_SDHC_SYSCTL_RD() & ~BM_SDHC_SYSCTL_SDCLKFS) | BF_SDHC_SYSCTL_SDCLKFS(v))) #endif //@} /*! * @name Register SDHC_SYSCTL, field DTOCV[19:16] (RW) * * Determines the interval by which DAT line timeouts are detected. See * IRQSTAT[DTOE] for information on factors that dictate time-out generation. Time-out * clock frequency will be generated by dividing the base clock SDCLK value by this * value. The host driver can clear IRQSTATEN[DTOESEN] to prevent inadvertent * time-out events. * * Values: * - 0000 - SDCLK x 2 13 * - 0001 - SDCLK x 2 14 * - 1110 - SDCLK x 2 27 * - 1111 - Reserved */ //@{ #define BP_SDHC_SYSCTL_DTOCV (16U) //!< Bit position for SDHC_SYSCTL_DTOCV. #define BM_SDHC_SYSCTL_DTOCV (0x000F0000U) //!< Bit mask for SDHC_SYSCTL_DTOCV. #define BS_SDHC_SYSCTL_DTOCV (4U) //!< Bit field size in bits for SDHC_SYSCTL_DTOCV. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_DTOCV field. #define BR_SDHC_SYSCTL_DTOCV (HW_SDHC_SYSCTL.B.DTOCV) #endif //! @brief Format value for bitfield SDHC_SYSCTL_DTOCV. #define BF_SDHC_SYSCTL_DTOCV(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_DTOCV), uint32_t) & BM_SDHC_SYSCTL_DTOCV) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTOCV field to a new value. #define BW_SDHC_SYSCTL_DTOCV(v) (HW_SDHC_SYSCTL_WR((HW_SDHC_SYSCTL_RD() & ~BM_SDHC_SYSCTL_DTOCV) | BF_SDHC_SYSCTL_DTOCV(v))) #endif //@} /*! * @name Register SDHC_SYSCTL, field RSTA[24] (WORZ) * * Effects the entire host controller except for the card detection circuit. * Register bits of type ROC, RW, RW1C, RWAC are cleared. During its initialization, * the host driver shall set this bit to 1 to reset the SDHC. The SDHC shall * reset this bit to 0 when the capabilities registers are valid and the host driver * can read them. Additional use of software reset for all does not affect the * value of the capabilities registers. After this bit is set, it is recommended * that the host driver reset the external card and reinitialize it. * * Values: * - 0 - No reset. * - 1 - Reset. */ //@{ #define BP_SDHC_SYSCTL_RSTA (24U) //!< Bit position for SDHC_SYSCTL_RSTA. #define BM_SDHC_SYSCTL_RSTA (0x01000000U) //!< Bit mask for SDHC_SYSCTL_RSTA. #define BS_SDHC_SYSCTL_RSTA (1U) //!< Bit field size in bits for SDHC_SYSCTL_RSTA. //! @brief Format value for bitfield SDHC_SYSCTL_RSTA. #define BF_SDHC_SYSCTL_RSTA(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_RSTA), uint32_t) & BM_SDHC_SYSCTL_RSTA) #ifndef __LANGUAGE_ASM__ //! @brief Set the RSTA field to a new value. #define BW_SDHC_SYSCTL_RSTA(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_RSTA) = (v)) #endif //@} /*! * @name Register SDHC_SYSCTL, field RSTC[25] (WORZ) * * Only part of the command circuit is reset. The following registers and bits * are cleared by this bit: PRSSTAT[CIHB] IRQSTAT[CC] * * Values: * - 0 - No reset. * - 1 - Reset. */ //@{ #define BP_SDHC_SYSCTL_RSTC (25U) //!< Bit position for SDHC_SYSCTL_RSTC. #define BM_SDHC_SYSCTL_RSTC (0x02000000U) //!< Bit mask for SDHC_SYSCTL_RSTC. #define BS_SDHC_SYSCTL_RSTC (1U) //!< Bit field size in bits for SDHC_SYSCTL_RSTC. //! @brief Format value for bitfield SDHC_SYSCTL_RSTC. #define BF_SDHC_SYSCTL_RSTC(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_RSTC), uint32_t) & BM_SDHC_SYSCTL_RSTC) #ifndef __LANGUAGE_ASM__ //! @brief Set the RSTC field to a new value. #define BW_SDHC_SYSCTL_RSTC(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_RSTC) = (v)) #endif //@} /*! * @name Register SDHC_SYSCTL, field RSTD[26] (WORZ) * * Only part of the data circuit is reset. DMA circuit is also reset. The * following registers and bits are cleared by this bit: Data Port register Buffer Is * Cleared And Initialized.Present State register Buffer Read Enable Buffer Write * Enable Read Transfer Active Write Transfer Active DAT Line Active Command * Inhibit (DAT) Protocol Control register Continue Request Stop At Block Gap Request * Interrupt Status register Buffer Read Ready Buffer Write Ready DMA Interrupt * Block Gap Event Transfer Complete * * Values: * - 0 - No reset. * - 1 - Reset. */ //@{ #define BP_SDHC_SYSCTL_RSTD (26U) //!< Bit position for SDHC_SYSCTL_RSTD. #define BM_SDHC_SYSCTL_RSTD (0x04000000U) //!< Bit mask for SDHC_SYSCTL_RSTD. #define BS_SDHC_SYSCTL_RSTD (1U) //!< Bit field size in bits for SDHC_SYSCTL_RSTD. //! @brief Format value for bitfield SDHC_SYSCTL_RSTD. #define BF_SDHC_SYSCTL_RSTD(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_RSTD), uint32_t) & BM_SDHC_SYSCTL_RSTD) #ifndef __LANGUAGE_ASM__ //! @brief Set the RSTD field to a new value. #define BW_SDHC_SYSCTL_RSTD(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_RSTD) = (v)) #endif //@} /*! * @name Register SDHC_SYSCTL, field INITA[27] (RW) * * When this bit is set, 80 SD-clocks are sent to the card. After the 80 clocks * are sent, this bit is self-cleared. This bit is very useful during the card * power-up period when 74 SD-clocks are needed and the clock auto gating feature * is enabled. Writing 1 to this bit when this bit is already 1 has no effect. * Writing 0 to this bit at any time has no effect. When either of the PRSSTAT[CIHB] * and PRSSTAT[CDIHB] bits are set, writing 1 to this bit is ignored, that is, * when command line or data lines are active, write to this bit is not allowed. * On the otherhand, when this bit is set, that is, during intialization active * period, it is allowed to issue command, and the command bit stream will appear * on the CMD pad after all 80 clock cycles are done. So when this command ends, * the driver can make sure the 80 clock cycles are sent out. This is very useful * when the driver needs send 80 cycles to the card and does not want to wait * till this bit is self-cleared. */ //@{ #define BP_SDHC_SYSCTL_INITA (27U) //!< Bit position for SDHC_SYSCTL_INITA. #define BM_SDHC_SYSCTL_INITA (0x08000000U) //!< Bit mask for SDHC_SYSCTL_INITA. #define BS_SDHC_SYSCTL_INITA (1U) //!< Bit field size in bits for SDHC_SYSCTL_INITA. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_SYSCTL_INITA field. #define BR_SDHC_SYSCTL_INITA (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_INITA)) #endif //! @brief Format value for bitfield SDHC_SYSCTL_INITA. #define BF_SDHC_SYSCTL_INITA(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_SYSCTL_INITA), uint32_t) & BM_SDHC_SYSCTL_INITA) #ifndef __LANGUAGE_ASM__ //! @brief Set the INITA field to a new value. #define BW_SDHC_SYSCTL_INITA(v) (BITBAND_ACCESS32(HW_SDHC_SYSCTL_ADDR, BP_SDHC_SYSCTL_INITA) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_IRQSTAT - Interrupt Status register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_IRQSTAT - Interrupt Status register (RW) * * Reset value: 0x00000000U * * An interrupt is generated when the Normal Interrupt Signal Enable is enabled * and at least one of the status bits is set to 1. For all bits, writing 1 to a * bit clears it; writing to 0 keeps the bit unchanged. More than one status can * be cleared with a single register write. For Card Interrupt, before writing 1 * to clear, it is required that the card stops asserting the interrupt, meaning * that when the Card Driver services the interrupt condition, otherwise the CINT * bit will be asserted again. The table below shows the relationship between * the CTOE and the CC bits. SDHC status for CTOE/CC bit combinations Command * complete Command timeout error Meaning of the status 0 0 X X 1 Response not * received within 64 SDCLK cycles 1 0 Response received The table below shows the * relationship between the Transfer Complete and the Data Timeout Error. SDHC status * for data timeout error/transfer complete bit combinations Transfer complete * Data timeout error Meaning of the status 0 0 X 0 1 Timeout occurred during * transfer 1 X Data transfer complete The table below shows the relationship between * the command CRC Error (CCE) and Command Timeout Error (CTOE). SDHC status for * CCE/CTOE Bit Combinations Command complete Command timeout error Meaning of * the status 0 0 No error 0 1 Response timeout error 1 0 Response CRC error 1 1 * CMD line conflict */ typedef union _hw_sdhc_irqstat { uint32_t U; struct _hw_sdhc_irqstat_bitfields { uint32_t CC : 1; //!< [0] Command Complete uint32_t TC : 1; //!< [1] Transfer Complete uint32_t BGE : 1; //!< [2] Block Gap Event uint32_t DINT : 1; //!< [3] DMA Interrupt uint32_t BWR : 1; //!< [4] Buffer Write Ready uint32_t BRR : 1; //!< [5] Buffer Read Ready uint32_t CINS : 1; //!< [6] Card Insertion uint32_t CRM : 1; //!< [7] Card Removal uint32_t CINT : 1; //!< [8] Card Interrupt uint32_t RESERVED0 : 7; //!< [15:9] uint32_t CTOE : 1; //!< [16] Command Timeout Error uint32_t CCE : 1; //!< [17] Command CRC Error uint32_t CEBE : 1; //!< [18] Command End Bit Error uint32_t CIE : 1; //!< [19] Command Index Error uint32_t DTOE : 1; //!< [20] Data Timeout Error uint32_t DCE : 1; //!< [21] Data CRC Error uint32_t DEBE : 1; //!< [22] Data End Bit Error uint32_t RESERVED1 : 1; //!< [23] uint32_t AC12E : 1; //!< [24] Auto CMD12 Error uint32_t RESERVED2 : 3; //!< [27:25] uint32_t DMAE : 1; //!< [28] DMA Error uint32_t RESERVED3 : 3; //!< [31:29] } B; } hw_sdhc_irqstat_t; #endif /*! * @name Constants and macros for entire SDHC_IRQSTAT register */ //@{ #define HW_SDHC_IRQSTAT_ADDR (REGS_SDHC_BASE + 0x30U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_IRQSTAT (*(__IO hw_sdhc_irqstat_t *) HW_SDHC_IRQSTAT_ADDR) #define HW_SDHC_IRQSTAT_RD() (HW_SDHC_IRQSTAT.U) #define HW_SDHC_IRQSTAT_WR(v) (HW_SDHC_IRQSTAT.U = (v)) #define HW_SDHC_IRQSTAT_SET(v) (HW_SDHC_IRQSTAT_WR(HW_SDHC_IRQSTAT_RD() | (v))) #define HW_SDHC_IRQSTAT_CLR(v) (HW_SDHC_IRQSTAT_WR(HW_SDHC_IRQSTAT_RD() & ~(v))) #define HW_SDHC_IRQSTAT_TOG(v) (HW_SDHC_IRQSTAT_WR(HW_SDHC_IRQSTAT_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_IRQSTAT bitfields */ /*! * @name Register SDHC_IRQSTAT, field CC[0] (W1C) * * This bit is set when you receive the end bit of the command response, except * Auto CMD12. See PRSSTAT[CIHB]. * * Values: * - 0 - Command not complete. * - 1 - Command complete. */ //@{ #define BP_SDHC_IRQSTAT_CC (0U) //!< Bit position for SDHC_IRQSTAT_CC. #define BM_SDHC_IRQSTAT_CC (0x00000001U) //!< Bit mask for SDHC_IRQSTAT_CC. #define BS_SDHC_IRQSTAT_CC (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CC. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CC field. #define BR_SDHC_IRQSTAT_CC (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CC)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CC. #define BF_SDHC_IRQSTAT_CC(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CC), uint32_t) & BM_SDHC_IRQSTAT_CC) #ifndef __LANGUAGE_ASM__ //! @brief Set the CC field to a new value. #define BW_SDHC_IRQSTAT_CC(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CC) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field TC[1] (W1C) * * This bit is set when a read or write transfer is completed. In the case of a * read transaction: This bit is set at the falling edge of the read transfer * active status. There are two cases in which this interrupt is generated. The * first is when a data transfer is completed as specified by the data length, after * the last data has been read to the host system. The second is when data has * stopped at the block gap and completed the data transfer by setting * PROCTL[SABGREQ], after valid data has been read to the host system. In the case of a write * transaction: This bit is set at the falling edge of the DAT line active * status. There are two cases in which this interrupt is generated. The first is when * the last data is written to the SD card as specified by the data length and * the busy signal is released. The second is when data transfers are stopped at * the block gap, by setting PROCTL[SABGREQ], and the data transfers are * completed,after valid data is written to the SD card and the busy signal released. * * Values: * - 0 - Transfer not complete. * - 1 - Transfer complete. */ //@{ #define BP_SDHC_IRQSTAT_TC (1U) //!< Bit position for SDHC_IRQSTAT_TC. #define BM_SDHC_IRQSTAT_TC (0x00000002U) //!< Bit mask for SDHC_IRQSTAT_TC. #define BS_SDHC_IRQSTAT_TC (1U) //!< Bit field size in bits for SDHC_IRQSTAT_TC. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_TC field. #define BR_SDHC_IRQSTAT_TC (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_TC)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_TC. #define BF_SDHC_IRQSTAT_TC(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_TC), uint32_t) & BM_SDHC_IRQSTAT_TC) #ifndef __LANGUAGE_ASM__ //! @brief Set the TC field to a new value. #define BW_SDHC_IRQSTAT_TC(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_TC) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field BGE[2] (W1C) * * If PROCTL[SABGREQ] is set, this bit is set when a read or write transaction * is stopped at a block gap. If PROCTL[SABGREQ] is not set to 1, this bit is not * set to 1. In the case of a read transaction: This bit is set at the falling * edge of the DAT line active status, when the transaction is stopped at SD Bus * timing. The read wait must be supported in order to use this function. In the * case of write transaction: This bit is set at the falling edge of write transfer * active status, after getting CRC status at SD bus timing. * * Values: * - 0 - No block gap event. * - 1 - Transaction stopped at block gap. */ //@{ #define BP_SDHC_IRQSTAT_BGE (2U) //!< Bit position for SDHC_IRQSTAT_BGE. #define BM_SDHC_IRQSTAT_BGE (0x00000004U) //!< Bit mask for SDHC_IRQSTAT_BGE. #define BS_SDHC_IRQSTAT_BGE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_BGE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_BGE field. #define BR_SDHC_IRQSTAT_BGE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BGE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_BGE. #define BF_SDHC_IRQSTAT_BGE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_BGE), uint32_t) & BM_SDHC_IRQSTAT_BGE) #ifndef __LANGUAGE_ASM__ //! @brief Set the BGE field to a new value. #define BW_SDHC_IRQSTAT_BGE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BGE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field DINT[3] (W1C) * * Occurs only when the internal DMA finishes the data transfer successfully. * Whenever errors occur during data transfer, this bit will not be set. Instead, * the DMAE bit will be set. Either Simple DMA or ADMA finishes data transferring, * this bit will be set. * * Values: * - 0 - No DMA Interrupt. * - 1 - DMA Interrupt is generated. */ //@{ #define BP_SDHC_IRQSTAT_DINT (3U) //!< Bit position for SDHC_IRQSTAT_DINT. #define BM_SDHC_IRQSTAT_DINT (0x00000008U) //!< Bit mask for SDHC_IRQSTAT_DINT. #define BS_SDHC_IRQSTAT_DINT (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DINT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_DINT field. #define BR_SDHC_IRQSTAT_DINT (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DINT)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_DINT. #define BF_SDHC_IRQSTAT_DINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DINT), uint32_t) & BM_SDHC_IRQSTAT_DINT) #ifndef __LANGUAGE_ASM__ //! @brief Set the DINT field to a new value. #define BW_SDHC_IRQSTAT_DINT(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DINT) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field BWR[4] (W1C) * * This status bit is set if the Buffer Write Enable bit, in the Present State * register, changes from 0 to 1. See the Buffer Write Enable bit in the Present * State register for additional information. * * Values: * - 0 - Not ready to write buffer. * - 1 - Ready to write buffer. */ //@{ #define BP_SDHC_IRQSTAT_BWR (4U) //!< Bit position for SDHC_IRQSTAT_BWR. #define BM_SDHC_IRQSTAT_BWR (0x00000010U) //!< Bit mask for SDHC_IRQSTAT_BWR. #define BS_SDHC_IRQSTAT_BWR (1U) //!< Bit field size in bits for SDHC_IRQSTAT_BWR. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_BWR field. #define BR_SDHC_IRQSTAT_BWR (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BWR)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_BWR. #define BF_SDHC_IRQSTAT_BWR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_BWR), uint32_t) & BM_SDHC_IRQSTAT_BWR) #ifndef __LANGUAGE_ASM__ //! @brief Set the BWR field to a new value. #define BW_SDHC_IRQSTAT_BWR(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BWR) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field BRR[5] (W1C) * * This status bit is set if the Buffer Read Enable bit, in the Present State * register, changes from 0 to 1. See the Buffer Read Enable bit in the Present * State register for additional information. * * Values: * - 0 - Not ready to read buffer. * - 1 - Ready to read buffer. */ //@{ #define BP_SDHC_IRQSTAT_BRR (5U) //!< Bit position for SDHC_IRQSTAT_BRR. #define BM_SDHC_IRQSTAT_BRR (0x00000020U) //!< Bit mask for SDHC_IRQSTAT_BRR. #define BS_SDHC_IRQSTAT_BRR (1U) //!< Bit field size in bits for SDHC_IRQSTAT_BRR. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_BRR field. #define BR_SDHC_IRQSTAT_BRR (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BRR)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_BRR. #define BF_SDHC_IRQSTAT_BRR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_BRR), uint32_t) & BM_SDHC_IRQSTAT_BRR) #ifndef __LANGUAGE_ASM__ //! @brief Set the BRR field to a new value. #define BW_SDHC_IRQSTAT_BRR(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_BRR) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field CINS[6] (W1C) * * This status bit is set if the Card Inserted bit in the Present State register * changes from 0 to 1. When the host driver writes this bit to 1 to clear this * status, the status of the Card Inserted in the Present State register must be * confirmed. Because the card state may possibly be changed when the host driver * clears this bit and the interrupt event may not be generated. When this bit * is cleared, it will be set again if a card is inserted. To leave it cleared, * clear the Card Inserted Status Enable bit in Interrupt Status Enable register. * * Values: * - 0 - Card state unstable or removed. * - 1 - Card inserted. */ //@{ #define BP_SDHC_IRQSTAT_CINS (6U) //!< Bit position for SDHC_IRQSTAT_CINS. #define BM_SDHC_IRQSTAT_CINS (0x00000040U) //!< Bit mask for SDHC_IRQSTAT_CINS. #define BS_SDHC_IRQSTAT_CINS (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CINS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CINS field. #define BR_SDHC_IRQSTAT_CINS (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINS)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CINS. #define BF_SDHC_IRQSTAT_CINS(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CINS), uint32_t) & BM_SDHC_IRQSTAT_CINS) #ifndef __LANGUAGE_ASM__ //! @brief Set the CINS field to a new value. #define BW_SDHC_IRQSTAT_CINS(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINS) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field CRM[7] (W1C) * * This status bit is set if the Card Inserted bit in the Present State register * changes from 1 to 0. When the host driver writes this bit to 1 to clear this * status, the status of the Card Inserted in the Present State register must be * confirmed. Because the card state may possibly be changed when the host driver * clears this bit and the interrupt event may not be generated. When this bit * is cleared, it will be set again if no card is inserted. To leave it cleared, * clear the Card Removal Status Enable bit in Interrupt Status Enable register. * * Values: * - 0 - Card state unstable or inserted. * - 1 - Card removed. */ //@{ #define BP_SDHC_IRQSTAT_CRM (7U) //!< Bit position for SDHC_IRQSTAT_CRM. #define BM_SDHC_IRQSTAT_CRM (0x00000080U) //!< Bit mask for SDHC_IRQSTAT_CRM. #define BS_SDHC_IRQSTAT_CRM (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CRM. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CRM field. #define BR_SDHC_IRQSTAT_CRM (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CRM)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CRM. #define BF_SDHC_IRQSTAT_CRM(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CRM), uint32_t) & BM_SDHC_IRQSTAT_CRM) #ifndef __LANGUAGE_ASM__ //! @brief Set the CRM field to a new value. #define BW_SDHC_IRQSTAT_CRM(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CRM) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field CINT[8] (W1C) * * This status bit is set when an interrupt signal is detected from the external * card. In 1-bit mode, the SDHC will detect the Card Interrupt without the SD * Clock to support wakeup. In 4-bit mode, the card interrupt signal is sampled * during the interrupt cycle, so the interrupt from card can only be sampled * during interrupt cycle, introducing some delay between the interrupt signal from * the SDIO card and the interrupt to the host system. Writing this bit to 1 can * clear this bit, but as the interrupt factor from the SDIO card does not clear, * this bit is set again. To clear this bit, it is required to reset the interrupt * factor from the external card followed by a writing 1 to this bit. When this * status has been set, and the host driver needs to service this interrupt, the * Card Interrupt Signal Enable in the Interrupt Signal Enable register should be * 0 to stop driving the interrupt signal to the host system. After completion * of the card interrupt service (it must reset the interrupt factors in the SDIO * card and the interrupt signal may not be asserted), write 1 to clear this bit, * set the Card Interrupt Signal Enable to 1, and start sampling the interrupt * signal again. * * Values: * - 0 - No Card Interrupt. * - 1 - Generate Card Interrupt. */ //@{ #define BP_SDHC_IRQSTAT_CINT (8U) //!< Bit position for SDHC_IRQSTAT_CINT. #define BM_SDHC_IRQSTAT_CINT (0x00000100U) //!< Bit mask for SDHC_IRQSTAT_CINT. #define BS_SDHC_IRQSTAT_CINT (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CINT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CINT field. #define BR_SDHC_IRQSTAT_CINT (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINT)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CINT. #define BF_SDHC_IRQSTAT_CINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CINT), uint32_t) & BM_SDHC_IRQSTAT_CINT) #ifndef __LANGUAGE_ASM__ //! @brief Set the CINT field to a new value. #define BW_SDHC_IRQSTAT_CINT(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CINT) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field CTOE[16] (W1C) * * Occurs only if no response is returned within 64 SDCLK cycles from the end * bit of the command. If the SDHC detects a CMD line conflict, in which case a * Command CRC Error shall also be set, this bit shall be set without waiting for 64 * SDCLK cycles. This is because the command will be aborted by the SDHC. * * Values: * - 0 - No error. * - 1 - Time out. */ //@{ #define BP_SDHC_IRQSTAT_CTOE (16U) //!< Bit position for SDHC_IRQSTAT_CTOE. #define BM_SDHC_IRQSTAT_CTOE (0x00010000U) //!< Bit mask for SDHC_IRQSTAT_CTOE. #define BS_SDHC_IRQSTAT_CTOE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CTOE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CTOE field. #define BR_SDHC_IRQSTAT_CTOE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CTOE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CTOE. #define BF_SDHC_IRQSTAT_CTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CTOE), uint32_t) & BM_SDHC_IRQSTAT_CTOE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CTOE field to a new value. #define BW_SDHC_IRQSTAT_CTOE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CTOE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field CCE[17] (W1C) * * Command CRC Error is generated in two cases. If a response is returned and * the Command Timeout Error is set to 0, indicating no time-out, this bit is set * when detecting a CRC error in the command response. The SDHC detects a CMD line * conflict by monitoring the CMD line when a command is issued. If the SDHC * drives the CMD line to 1, but detects 0 on the CMD line at the next SDCLK edge, * then the SDHC shall abort the command (Stop driving CMD line) and set this bit * to 1. The Command Timeout Error shall also be set to 1 to distinguish CMD line * conflict. * * Values: * - 0 - No error. * - 1 - CRC Error generated. */ //@{ #define BP_SDHC_IRQSTAT_CCE (17U) //!< Bit position for SDHC_IRQSTAT_CCE. #define BM_SDHC_IRQSTAT_CCE (0x00020000U) //!< Bit mask for SDHC_IRQSTAT_CCE. #define BS_SDHC_IRQSTAT_CCE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CCE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CCE field. #define BR_SDHC_IRQSTAT_CCE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CCE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CCE. #define BF_SDHC_IRQSTAT_CCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CCE), uint32_t) & BM_SDHC_IRQSTAT_CCE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CCE field to a new value. #define BW_SDHC_IRQSTAT_CCE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CCE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field CEBE[18] (W1C) * * Occurs when detecting that the end bit of a command response is 0. * * Values: * - 0 - No error. * - 1 - End Bit Error generated. */ //@{ #define BP_SDHC_IRQSTAT_CEBE (18U) //!< Bit position for SDHC_IRQSTAT_CEBE. #define BM_SDHC_IRQSTAT_CEBE (0x00040000U) //!< Bit mask for SDHC_IRQSTAT_CEBE. #define BS_SDHC_IRQSTAT_CEBE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CEBE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CEBE field. #define BR_SDHC_IRQSTAT_CEBE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CEBE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CEBE. #define BF_SDHC_IRQSTAT_CEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CEBE), uint32_t) & BM_SDHC_IRQSTAT_CEBE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CEBE field to a new value. #define BW_SDHC_IRQSTAT_CEBE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CEBE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field CIE[19] (W1C) * * Occurs if a Command Index error occurs in the command response. * * Values: * - 0 - No error. * - 1 - Error. */ //@{ #define BP_SDHC_IRQSTAT_CIE (19U) //!< Bit position for SDHC_IRQSTAT_CIE. #define BM_SDHC_IRQSTAT_CIE (0x00080000U) //!< Bit mask for SDHC_IRQSTAT_CIE. #define BS_SDHC_IRQSTAT_CIE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_CIE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_CIE field. #define BR_SDHC_IRQSTAT_CIE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CIE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_CIE. #define BF_SDHC_IRQSTAT_CIE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_CIE), uint32_t) & BM_SDHC_IRQSTAT_CIE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CIE field to a new value. #define BW_SDHC_IRQSTAT_CIE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_CIE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field DTOE[20] (W1C) * * Occurs when detecting one of following time-out conditions. Busy time-out for * R1b,R5b type Busy time-out after Write CRC status Read Data time-out * * Values: * - 0 - No error. * - 1 - Time out. */ //@{ #define BP_SDHC_IRQSTAT_DTOE (20U) //!< Bit position for SDHC_IRQSTAT_DTOE. #define BM_SDHC_IRQSTAT_DTOE (0x00100000U) //!< Bit mask for SDHC_IRQSTAT_DTOE. #define BS_SDHC_IRQSTAT_DTOE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DTOE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_DTOE field. #define BR_SDHC_IRQSTAT_DTOE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DTOE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_DTOE. #define BF_SDHC_IRQSTAT_DTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DTOE), uint32_t) & BM_SDHC_IRQSTAT_DTOE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTOE field to a new value. #define BW_SDHC_IRQSTAT_DTOE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DTOE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field DCE[21] (W1C) * * Occurs when detecting a CRC error when transferring read data, which uses the * DAT line, or when detecting the Write CRC status having a value other than * 010. * * Values: * - 0 - No error. * - 1 - Error. */ //@{ #define BP_SDHC_IRQSTAT_DCE (21U) //!< Bit position for SDHC_IRQSTAT_DCE. #define BM_SDHC_IRQSTAT_DCE (0x00200000U) //!< Bit mask for SDHC_IRQSTAT_DCE. #define BS_SDHC_IRQSTAT_DCE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DCE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_DCE field. #define BR_SDHC_IRQSTAT_DCE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DCE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_DCE. #define BF_SDHC_IRQSTAT_DCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DCE), uint32_t) & BM_SDHC_IRQSTAT_DCE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DCE field to a new value. #define BW_SDHC_IRQSTAT_DCE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DCE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field DEBE[22] (W1C) * * Occurs either when detecting 0 at the end bit position of read data, which * uses the DAT line, or at the end bit position of the CRC. * * Values: * - 0 - No error. * - 1 - Error. */ //@{ #define BP_SDHC_IRQSTAT_DEBE (22U) //!< Bit position for SDHC_IRQSTAT_DEBE. #define BM_SDHC_IRQSTAT_DEBE (0x00400000U) //!< Bit mask for SDHC_IRQSTAT_DEBE. #define BS_SDHC_IRQSTAT_DEBE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DEBE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_DEBE field. #define BR_SDHC_IRQSTAT_DEBE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DEBE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_DEBE. #define BF_SDHC_IRQSTAT_DEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DEBE), uint32_t) & BM_SDHC_IRQSTAT_DEBE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DEBE field to a new value. #define BW_SDHC_IRQSTAT_DEBE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DEBE) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field AC12E[24] (W1C) * * Occurs when detecting that one of the bits in the Auto CMD12 Error Status * register has changed from 0 to 1. This bit is set to 1, not only when the errors * in Auto CMD12 occur, but also when the Auto CMD12 is not executed due to the * previous command error. * * Values: * - 0 - No error. * - 1 - Error. */ //@{ #define BP_SDHC_IRQSTAT_AC12E (24U) //!< Bit position for SDHC_IRQSTAT_AC12E. #define BM_SDHC_IRQSTAT_AC12E (0x01000000U) //!< Bit mask for SDHC_IRQSTAT_AC12E. #define BS_SDHC_IRQSTAT_AC12E (1U) //!< Bit field size in bits for SDHC_IRQSTAT_AC12E. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_AC12E field. #define BR_SDHC_IRQSTAT_AC12E (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_AC12E)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_AC12E. #define BF_SDHC_IRQSTAT_AC12E(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_AC12E), uint32_t) & BM_SDHC_IRQSTAT_AC12E) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12E field to a new value. #define BW_SDHC_IRQSTAT_AC12E(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_AC12E) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTAT, field DMAE[28] (W1C) * * Occurs when an Internal DMA transfer has failed. This bit is set to 1, when * some error occurs in the data transfer. This error can be caused by either * Simple DMA or ADMA, depending on which DMA is in use. The value in DMA System * Address register is the next fetch address where the error occurs. Because any * error corrupts the whole data block, the host driver shall restart the transfer * from the corrupted block boundary. The address of the block boundary can be * calculated either from the current DSADDR value or from the remaining number of * blocks and the block size. * * Values: * - 0 - No error. * - 1 - Error. */ //@{ #define BP_SDHC_IRQSTAT_DMAE (28U) //!< Bit position for SDHC_IRQSTAT_DMAE. #define BM_SDHC_IRQSTAT_DMAE (0x10000000U) //!< Bit mask for SDHC_IRQSTAT_DMAE. #define BS_SDHC_IRQSTAT_DMAE (1U) //!< Bit field size in bits for SDHC_IRQSTAT_DMAE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTAT_DMAE field. #define BR_SDHC_IRQSTAT_DMAE (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DMAE)) #endif //! @brief Format value for bitfield SDHC_IRQSTAT_DMAE. #define BF_SDHC_IRQSTAT_DMAE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTAT_DMAE), uint32_t) & BM_SDHC_IRQSTAT_DMAE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DMAE field to a new value. #define BW_SDHC_IRQSTAT_DMAE(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTAT_ADDR, BP_SDHC_IRQSTAT_DMAE) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_IRQSTATEN - Interrupt Status Enable register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_IRQSTATEN - Interrupt Status Enable register (RW) * * Reset value: 0x117F013FU * * Setting the bits in this register to 1 enables the corresponding interrupt * status to be set by the specified event. If any bit is cleared, the * corresponding interrupt status bit is also cleared, that is, when the bit in this register * is cleared, the corresponding bit in interrupt status register is always 0. * Depending on PROCTL[IABG] bit setting, SDHC may be programmed to sample the * card interrupt signal during the interrupt period and hold its value in the * flip-flop. There will be some delays on the card interrupt, asserted from the card, * to the time the host system is informed. To detect a CMD line conflict, the * host driver must set both IRQSTATEN[CTOESEN] and IRQSTATEN[CCESEN] to 1. */ typedef union _hw_sdhc_irqstaten { uint32_t U; struct _hw_sdhc_irqstaten_bitfields { uint32_t CCSEN : 1; //!< [0] Command Complete Status Enable uint32_t TCSEN : 1; //!< [1] Transfer Complete Status Enable uint32_t BGESEN : 1; //!< [2] Block Gap Event Status Enable uint32_t DINTSEN : 1; //!< [3] DMA Interrupt Status Enable uint32_t BWRSEN : 1; //!< [4] Buffer Write Ready Status Enable uint32_t BRRSEN : 1; //!< [5] Buffer Read Ready Status Enable uint32_t CINSEN : 1; //!< [6] Card Insertion Status Enable uint32_t CRMSEN : 1; //!< [7] Card Removal Status Enable uint32_t CINTSEN : 1; //!< [8] Card Interrupt Status Enable uint32_t RESERVED0 : 7; //!< [15:9] uint32_t CTOESEN : 1; //!< [16] Command Timeout Error Status Enable uint32_t CCESEN : 1; //!< [17] Command CRC Error Status Enable uint32_t CEBESEN : 1; //!< [18] Command End Bit Error Status Enable uint32_t CIESEN : 1; //!< [19] Command Index Error Status Enable uint32_t DTOESEN : 1; //!< [20] Data Timeout Error Status Enable uint32_t DCESEN : 1; //!< [21] Data CRC Error Status Enable uint32_t DEBESEN : 1; //!< [22] Data End Bit Error Status Enable uint32_t RESERVED1 : 1; //!< [23] uint32_t AC12ESEN : 1; //!< [24] Auto CMD12 Error Status Enable uint32_t RESERVED2 : 3; //!< [27:25] uint32_t DMAESEN : 1; //!< [28] DMA Error Status Enable uint32_t RESERVED3 : 3; //!< [31:29] } B; } hw_sdhc_irqstaten_t; #endif /*! * @name Constants and macros for entire SDHC_IRQSTATEN register */ //@{ #define HW_SDHC_IRQSTATEN_ADDR (REGS_SDHC_BASE + 0x34U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_IRQSTATEN (*(__IO hw_sdhc_irqstaten_t *) HW_SDHC_IRQSTATEN_ADDR) #define HW_SDHC_IRQSTATEN_RD() (HW_SDHC_IRQSTATEN.U) #define HW_SDHC_IRQSTATEN_WR(v) (HW_SDHC_IRQSTATEN.U = (v)) #define HW_SDHC_IRQSTATEN_SET(v) (HW_SDHC_IRQSTATEN_WR(HW_SDHC_IRQSTATEN_RD() | (v))) #define HW_SDHC_IRQSTATEN_CLR(v) (HW_SDHC_IRQSTATEN_WR(HW_SDHC_IRQSTATEN_RD() & ~(v))) #define HW_SDHC_IRQSTATEN_TOG(v) (HW_SDHC_IRQSTATEN_WR(HW_SDHC_IRQSTATEN_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_IRQSTATEN bitfields */ /*! * @name Register SDHC_IRQSTATEN, field CCSEN[0] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CCSEN (0U) //!< Bit position for SDHC_IRQSTATEN_CCSEN. #define BM_SDHC_IRQSTATEN_CCSEN (0x00000001U) //!< Bit mask for SDHC_IRQSTATEN_CCSEN. #define BS_SDHC_IRQSTATEN_CCSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CCSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CCSEN field. #define BR_SDHC_IRQSTATEN_CCSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CCSEN. #define BF_SDHC_IRQSTATEN_CCSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CCSEN), uint32_t) & BM_SDHC_IRQSTATEN_CCSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CCSEN field to a new value. #define BW_SDHC_IRQSTATEN_CCSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field TCSEN[1] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_TCSEN (1U) //!< Bit position for SDHC_IRQSTATEN_TCSEN. #define BM_SDHC_IRQSTATEN_TCSEN (0x00000002U) //!< Bit mask for SDHC_IRQSTATEN_TCSEN. #define BS_SDHC_IRQSTATEN_TCSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_TCSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_TCSEN field. #define BR_SDHC_IRQSTATEN_TCSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_TCSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_TCSEN. #define BF_SDHC_IRQSTATEN_TCSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_TCSEN), uint32_t) & BM_SDHC_IRQSTATEN_TCSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the TCSEN field to a new value. #define BW_SDHC_IRQSTATEN_TCSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_TCSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field BGESEN[2] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_BGESEN (2U) //!< Bit position for SDHC_IRQSTATEN_BGESEN. #define BM_SDHC_IRQSTATEN_BGESEN (0x00000004U) //!< Bit mask for SDHC_IRQSTATEN_BGESEN. #define BS_SDHC_IRQSTATEN_BGESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_BGESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_BGESEN field. #define BR_SDHC_IRQSTATEN_BGESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BGESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_BGESEN. #define BF_SDHC_IRQSTATEN_BGESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_BGESEN), uint32_t) & BM_SDHC_IRQSTATEN_BGESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BGESEN field to a new value. #define BW_SDHC_IRQSTATEN_BGESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BGESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field DINTSEN[3] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_DINTSEN (3U) //!< Bit position for SDHC_IRQSTATEN_DINTSEN. #define BM_SDHC_IRQSTATEN_DINTSEN (0x00000008U) //!< Bit mask for SDHC_IRQSTATEN_DINTSEN. #define BS_SDHC_IRQSTATEN_DINTSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DINTSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_DINTSEN field. #define BR_SDHC_IRQSTATEN_DINTSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DINTSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_DINTSEN. #define BF_SDHC_IRQSTATEN_DINTSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DINTSEN), uint32_t) & BM_SDHC_IRQSTATEN_DINTSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DINTSEN field to a new value. #define BW_SDHC_IRQSTATEN_DINTSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DINTSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field BWRSEN[4] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_BWRSEN (4U) //!< Bit position for SDHC_IRQSTATEN_BWRSEN. #define BM_SDHC_IRQSTATEN_BWRSEN (0x00000010U) //!< Bit mask for SDHC_IRQSTATEN_BWRSEN. #define BS_SDHC_IRQSTATEN_BWRSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_BWRSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_BWRSEN field. #define BR_SDHC_IRQSTATEN_BWRSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BWRSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_BWRSEN. #define BF_SDHC_IRQSTATEN_BWRSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_BWRSEN), uint32_t) & BM_SDHC_IRQSTATEN_BWRSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BWRSEN field to a new value. #define BW_SDHC_IRQSTATEN_BWRSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BWRSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field BRRSEN[5] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_BRRSEN (5U) //!< Bit position for SDHC_IRQSTATEN_BRRSEN. #define BM_SDHC_IRQSTATEN_BRRSEN (0x00000020U) //!< Bit mask for SDHC_IRQSTATEN_BRRSEN. #define BS_SDHC_IRQSTATEN_BRRSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_BRRSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_BRRSEN field. #define BR_SDHC_IRQSTATEN_BRRSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BRRSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_BRRSEN. #define BF_SDHC_IRQSTATEN_BRRSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_BRRSEN), uint32_t) & BM_SDHC_IRQSTATEN_BRRSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BRRSEN field to a new value. #define BW_SDHC_IRQSTATEN_BRRSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_BRRSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field CINSEN[6] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CINSEN (6U) //!< Bit position for SDHC_IRQSTATEN_CINSEN. #define BM_SDHC_IRQSTATEN_CINSEN (0x00000040U) //!< Bit mask for SDHC_IRQSTATEN_CINSEN. #define BS_SDHC_IRQSTATEN_CINSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CINSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CINSEN field. #define BR_SDHC_IRQSTATEN_CINSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CINSEN. #define BF_SDHC_IRQSTATEN_CINSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CINSEN), uint32_t) & BM_SDHC_IRQSTATEN_CINSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CINSEN field to a new value. #define BW_SDHC_IRQSTATEN_CINSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field CRMSEN[7] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CRMSEN (7U) //!< Bit position for SDHC_IRQSTATEN_CRMSEN. #define BM_SDHC_IRQSTATEN_CRMSEN (0x00000080U) //!< Bit mask for SDHC_IRQSTATEN_CRMSEN. #define BS_SDHC_IRQSTATEN_CRMSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CRMSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CRMSEN field. #define BR_SDHC_IRQSTATEN_CRMSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CRMSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CRMSEN. #define BF_SDHC_IRQSTATEN_CRMSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CRMSEN), uint32_t) & BM_SDHC_IRQSTATEN_CRMSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CRMSEN field to a new value. #define BW_SDHC_IRQSTATEN_CRMSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CRMSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field CINTSEN[8] (RW) * * If this bit is set to 0, the SDHC will clear the interrupt request to the * system. The card interrupt detection is stopped when this bit is cleared and * restarted when this bit is set to 1. The host driver must clear the this bit * before servicing the card interrupt and must set this bit again after all interrupt * requests from the card are cleared to prevent inadvertent interrupts. * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CINTSEN (8U) //!< Bit position for SDHC_IRQSTATEN_CINTSEN. #define BM_SDHC_IRQSTATEN_CINTSEN (0x00000100U) //!< Bit mask for SDHC_IRQSTATEN_CINTSEN. #define BS_SDHC_IRQSTATEN_CINTSEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CINTSEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CINTSEN field. #define BR_SDHC_IRQSTATEN_CINTSEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINTSEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CINTSEN. #define BF_SDHC_IRQSTATEN_CINTSEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CINTSEN), uint32_t) & BM_SDHC_IRQSTATEN_CINTSEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CINTSEN field to a new value. #define BW_SDHC_IRQSTATEN_CINTSEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CINTSEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field CTOESEN[16] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CTOESEN (16U) //!< Bit position for SDHC_IRQSTATEN_CTOESEN. #define BM_SDHC_IRQSTATEN_CTOESEN (0x00010000U) //!< Bit mask for SDHC_IRQSTATEN_CTOESEN. #define BS_SDHC_IRQSTATEN_CTOESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CTOESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CTOESEN field. #define BR_SDHC_IRQSTATEN_CTOESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CTOESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CTOESEN. #define BF_SDHC_IRQSTATEN_CTOESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CTOESEN), uint32_t) & BM_SDHC_IRQSTATEN_CTOESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CTOESEN field to a new value. #define BW_SDHC_IRQSTATEN_CTOESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CTOESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field CCESEN[17] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CCESEN (17U) //!< Bit position for SDHC_IRQSTATEN_CCESEN. #define BM_SDHC_IRQSTATEN_CCESEN (0x00020000U) //!< Bit mask for SDHC_IRQSTATEN_CCESEN. #define BS_SDHC_IRQSTATEN_CCESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CCESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CCESEN field. #define BR_SDHC_IRQSTATEN_CCESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CCESEN. #define BF_SDHC_IRQSTATEN_CCESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CCESEN), uint32_t) & BM_SDHC_IRQSTATEN_CCESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CCESEN field to a new value. #define BW_SDHC_IRQSTATEN_CCESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CCESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field CEBESEN[18] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CEBESEN (18U) //!< Bit position for SDHC_IRQSTATEN_CEBESEN. #define BM_SDHC_IRQSTATEN_CEBESEN (0x00040000U) //!< Bit mask for SDHC_IRQSTATEN_CEBESEN. #define BS_SDHC_IRQSTATEN_CEBESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CEBESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CEBESEN field. #define BR_SDHC_IRQSTATEN_CEBESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CEBESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CEBESEN. #define BF_SDHC_IRQSTATEN_CEBESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CEBESEN), uint32_t) & BM_SDHC_IRQSTATEN_CEBESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CEBESEN field to a new value. #define BW_SDHC_IRQSTATEN_CEBESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CEBESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field CIESEN[19] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_CIESEN (19U) //!< Bit position for SDHC_IRQSTATEN_CIESEN. #define BM_SDHC_IRQSTATEN_CIESEN (0x00080000U) //!< Bit mask for SDHC_IRQSTATEN_CIESEN. #define BS_SDHC_IRQSTATEN_CIESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_CIESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_CIESEN field. #define BR_SDHC_IRQSTATEN_CIESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CIESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_CIESEN. #define BF_SDHC_IRQSTATEN_CIESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_CIESEN), uint32_t) & BM_SDHC_IRQSTATEN_CIESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CIESEN field to a new value. #define BW_SDHC_IRQSTATEN_CIESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_CIESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field DTOESEN[20] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_DTOESEN (20U) //!< Bit position for SDHC_IRQSTATEN_DTOESEN. #define BM_SDHC_IRQSTATEN_DTOESEN (0x00100000U) //!< Bit mask for SDHC_IRQSTATEN_DTOESEN. #define BS_SDHC_IRQSTATEN_DTOESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DTOESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_DTOESEN field. #define BR_SDHC_IRQSTATEN_DTOESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DTOESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_DTOESEN. #define BF_SDHC_IRQSTATEN_DTOESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DTOESEN), uint32_t) & BM_SDHC_IRQSTATEN_DTOESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTOESEN field to a new value. #define BW_SDHC_IRQSTATEN_DTOESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DTOESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field DCESEN[21] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_DCESEN (21U) //!< Bit position for SDHC_IRQSTATEN_DCESEN. #define BM_SDHC_IRQSTATEN_DCESEN (0x00200000U) //!< Bit mask for SDHC_IRQSTATEN_DCESEN. #define BS_SDHC_IRQSTATEN_DCESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DCESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_DCESEN field. #define BR_SDHC_IRQSTATEN_DCESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DCESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_DCESEN. #define BF_SDHC_IRQSTATEN_DCESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DCESEN), uint32_t) & BM_SDHC_IRQSTATEN_DCESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DCESEN field to a new value. #define BW_SDHC_IRQSTATEN_DCESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DCESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field DEBESEN[22] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_DEBESEN (22U) //!< Bit position for SDHC_IRQSTATEN_DEBESEN. #define BM_SDHC_IRQSTATEN_DEBESEN (0x00400000U) //!< Bit mask for SDHC_IRQSTATEN_DEBESEN. #define BS_SDHC_IRQSTATEN_DEBESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DEBESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_DEBESEN field. #define BR_SDHC_IRQSTATEN_DEBESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DEBESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_DEBESEN. #define BF_SDHC_IRQSTATEN_DEBESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DEBESEN), uint32_t) & BM_SDHC_IRQSTATEN_DEBESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DEBESEN field to a new value. #define BW_SDHC_IRQSTATEN_DEBESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DEBESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field AC12ESEN[24] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_AC12ESEN (24U) //!< Bit position for SDHC_IRQSTATEN_AC12ESEN. #define BM_SDHC_IRQSTATEN_AC12ESEN (0x01000000U) //!< Bit mask for SDHC_IRQSTATEN_AC12ESEN. #define BS_SDHC_IRQSTATEN_AC12ESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_AC12ESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_AC12ESEN field. #define BR_SDHC_IRQSTATEN_AC12ESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_AC12ESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_AC12ESEN. #define BF_SDHC_IRQSTATEN_AC12ESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_AC12ESEN), uint32_t) & BM_SDHC_IRQSTATEN_AC12ESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12ESEN field to a new value. #define BW_SDHC_IRQSTATEN_AC12ESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_AC12ESEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSTATEN, field DMAESEN[28] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSTATEN_DMAESEN (28U) //!< Bit position for SDHC_IRQSTATEN_DMAESEN. #define BM_SDHC_IRQSTATEN_DMAESEN (0x10000000U) //!< Bit mask for SDHC_IRQSTATEN_DMAESEN. #define BS_SDHC_IRQSTATEN_DMAESEN (1U) //!< Bit field size in bits for SDHC_IRQSTATEN_DMAESEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSTATEN_DMAESEN field. #define BR_SDHC_IRQSTATEN_DMAESEN (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DMAESEN)) #endif //! @brief Format value for bitfield SDHC_IRQSTATEN_DMAESEN. #define BF_SDHC_IRQSTATEN_DMAESEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSTATEN_DMAESEN), uint32_t) & BM_SDHC_IRQSTATEN_DMAESEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DMAESEN field to a new value. #define BW_SDHC_IRQSTATEN_DMAESEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSTATEN_ADDR, BP_SDHC_IRQSTATEN_DMAESEN) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_IRQSIGEN - Interrupt Signal Enable register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_IRQSIGEN - Interrupt Signal Enable register (RW) * * Reset value: 0x00000000U * * This register is used to select which interrupt status is indicated to the * host system as the interrupt. All of these status bits share the same interrupt * line. Setting any of these bits to 1 enables interrupt generation. The * corresponding status register bit will generate an interrupt when the corresponding * interrupt signal enable bit is set. */ typedef union _hw_sdhc_irqsigen { uint32_t U; struct _hw_sdhc_irqsigen_bitfields { uint32_t CCIEN : 1; //!< [0] Command Complete Interrupt Enable uint32_t TCIEN : 1; //!< [1] Transfer Complete Interrupt Enable uint32_t BGEIEN : 1; //!< [2] Block Gap Event Interrupt Enable uint32_t DINTIEN : 1; //!< [3] DMA Interrupt Enable uint32_t BWRIEN : 1; //!< [4] Buffer Write Ready Interrupt Enable uint32_t BRRIEN : 1; //!< [5] Buffer Read Ready Interrupt Enable uint32_t CINSIEN : 1; //!< [6] Card Insertion Interrupt Enable uint32_t CRMIEN : 1; //!< [7] Card Removal Interrupt Enable uint32_t CINTIEN : 1; //!< [8] Card Interrupt Enable uint32_t RESERVED0 : 7; //!< [15:9] uint32_t CTOEIEN : 1; //!< [16] Command Timeout Error Interrupt Enable uint32_t CCEIEN : 1; //!< [17] Command CRC Error Interrupt Enable uint32_t CEBEIEN : 1; //!< [18] Command End Bit Error Interrupt Enable uint32_t CIEIEN : 1; //!< [19] Command Index Error Interrupt Enable uint32_t DTOEIEN : 1; //!< [20] Data Timeout Error Interrupt Enable uint32_t DCEIEN : 1; //!< [21] Data CRC Error Interrupt Enable uint32_t DEBEIEN : 1; //!< [22] Data End Bit Error Interrupt Enable uint32_t RESERVED1 : 1; //!< [23] uint32_t AC12EIEN : 1; //!< [24] Auto CMD12 Error Interrupt Enable uint32_t RESERVED2 : 3; //!< [27:25] uint32_t DMAEIEN : 1; //!< [28] DMA Error Interrupt Enable uint32_t RESERVED3 : 3; //!< [31:29] } B; } hw_sdhc_irqsigen_t; #endif /*! * @name Constants and macros for entire SDHC_IRQSIGEN register */ //@{ #define HW_SDHC_IRQSIGEN_ADDR (REGS_SDHC_BASE + 0x38U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_IRQSIGEN (*(__IO hw_sdhc_irqsigen_t *) HW_SDHC_IRQSIGEN_ADDR) #define HW_SDHC_IRQSIGEN_RD() (HW_SDHC_IRQSIGEN.U) #define HW_SDHC_IRQSIGEN_WR(v) (HW_SDHC_IRQSIGEN.U = (v)) #define HW_SDHC_IRQSIGEN_SET(v) (HW_SDHC_IRQSIGEN_WR(HW_SDHC_IRQSIGEN_RD() | (v))) #define HW_SDHC_IRQSIGEN_CLR(v) (HW_SDHC_IRQSIGEN_WR(HW_SDHC_IRQSIGEN_RD() & ~(v))) #define HW_SDHC_IRQSIGEN_TOG(v) (HW_SDHC_IRQSIGEN_WR(HW_SDHC_IRQSIGEN_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_IRQSIGEN bitfields */ /*! * @name Register SDHC_IRQSIGEN, field CCIEN[0] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CCIEN (0U) //!< Bit position for SDHC_IRQSIGEN_CCIEN. #define BM_SDHC_IRQSIGEN_CCIEN (0x00000001U) //!< Bit mask for SDHC_IRQSIGEN_CCIEN. #define BS_SDHC_IRQSIGEN_CCIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CCIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CCIEN field. #define BR_SDHC_IRQSIGEN_CCIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CCIEN. #define BF_SDHC_IRQSIGEN_CCIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CCIEN), uint32_t) & BM_SDHC_IRQSIGEN_CCIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CCIEN field to a new value. #define BW_SDHC_IRQSIGEN_CCIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field TCIEN[1] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_TCIEN (1U) //!< Bit position for SDHC_IRQSIGEN_TCIEN. #define BM_SDHC_IRQSIGEN_TCIEN (0x00000002U) //!< Bit mask for SDHC_IRQSIGEN_TCIEN. #define BS_SDHC_IRQSIGEN_TCIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_TCIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_TCIEN field. #define BR_SDHC_IRQSIGEN_TCIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_TCIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_TCIEN. #define BF_SDHC_IRQSIGEN_TCIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_TCIEN), uint32_t) & BM_SDHC_IRQSIGEN_TCIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the TCIEN field to a new value. #define BW_SDHC_IRQSIGEN_TCIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_TCIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field BGEIEN[2] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_BGEIEN (2U) //!< Bit position for SDHC_IRQSIGEN_BGEIEN. #define BM_SDHC_IRQSIGEN_BGEIEN (0x00000004U) //!< Bit mask for SDHC_IRQSIGEN_BGEIEN. #define BS_SDHC_IRQSIGEN_BGEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_BGEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_BGEIEN field. #define BR_SDHC_IRQSIGEN_BGEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BGEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_BGEIEN. #define BF_SDHC_IRQSIGEN_BGEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_BGEIEN), uint32_t) & BM_SDHC_IRQSIGEN_BGEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BGEIEN field to a new value. #define BW_SDHC_IRQSIGEN_BGEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BGEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field DINTIEN[3] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_DINTIEN (3U) //!< Bit position for SDHC_IRQSIGEN_DINTIEN. #define BM_SDHC_IRQSIGEN_DINTIEN (0x00000008U) //!< Bit mask for SDHC_IRQSIGEN_DINTIEN. #define BS_SDHC_IRQSIGEN_DINTIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DINTIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_DINTIEN field. #define BR_SDHC_IRQSIGEN_DINTIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DINTIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_DINTIEN. #define BF_SDHC_IRQSIGEN_DINTIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DINTIEN), uint32_t) & BM_SDHC_IRQSIGEN_DINTIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DINTIEN field to a new value. #define BW_SDHC_IRQSIGEN_DINTIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DINTIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field BWRIEN[4] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_BWRIEN (4U) //!< Bit position for SDHC_IRQSIGEN_BWRIEN. #define BM_SDHC_IRQSIGEN_BWRIEN (0x00000010U) //!< Bit mask for SDHC_IRQSIGEN_BWRIEN. #define BS_SDHC_IRQSIGEN_BWRIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_BWRIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_BWRIEN field. #define BR_SDHC_IRQSIGEN_BWRIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BWRIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_BWRIEN. #define BF_SDHC_IRQSIGEN_BWRIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_BWRIEN), uint32_t) & BM_SDHC_IRQSIGEN_BWRIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BWRIEN field to a new value. #define BW_SDHC_IRQSIGEN_BWRIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BWRIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field BRRIEN[5] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_BRRIEN (5U) //!< Bit position for SDHC_IRQSIGEN_BRRIEN. #define BM_SDHC_IRQSIGEN_BRRIEN (0x00000020U) //!< Bit mask for SDHC_IRQSIGEN_BRRIEN. #define BS_SDHC_IRQSIGEN_BRRIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_BRRIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_BRRIEN field. #define BR_SDHC_IRQSIGEN_BRRIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BRRIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_BRRIEN. #define BF_SDHC_IRQSIGEN_BRRIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_BRRIEN), uint32_t) & BM_SDHC_IRQSIGEN_BRRIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BRRIEN field to a new value. #define BW_SDHC_IRQSIGEN_BRRIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_BRRIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field CINSIEN[6] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CINSIEN (6U) //!< Bit position for SDHC_IRQSIGEN_CINSIEN. #define BM_SDHC_IRQSIGEN_CINSIEN (0x00000040U) //!< Bit mask for SDHC_IRQSIGEN_CINSIEN. #define BS_SDHC_IRQSIGEN_CINSIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CINSIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CINSIEN field. #define BR_SDHC_IRQSIGEN_CINSIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINSIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CINSIEN. #define BF_SDHC_IRQSIGEN_CINSIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CINSIEN), uint32_t) & BM_SDHC_IRQSIGEN_CINSIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CINSIEN field to a new value. #define BW_SDHC_IRQSIGEN_CINSIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINSIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field CRMIEN[7] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CRMIEN (7U) //!< Bit position for SDHC_IRQSIGEN_CRMIEN. #define BM_SDHC_IRQSIGEN_CRMIEN (0x00000080U) //!< Bit mask for SDHC_IRQSIGEN_CRMIEN. #define BS_SDHC_IRQSIGEN_CRMIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CRMIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CRMIEN field. #define BR_SDHC_IRQSIGEN_CRMIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CRMIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CRMIEN. #define BF_SDHC_IRQSIGEN_CRMIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CRMIEN), uint32_t) & BM_SDHC_IRQSIGEN_CRMIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CRMIEN field to a new value. #define BW_SDHC_IRQSIGEN_CRMIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CRMIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field CINTIEN[8] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CINTIEN (8U) //!< Bit position for SDHC_IRQSIGEN_CINTIEN. #define BM_SDHC_IRQSIGEN_CINTIEN (0x00000100U) //!< Bit mask for SDHC_IRQSIGEN_CINTIEN. #define BS_SDHC_IRQSIGEN_CINTIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CINTIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CINTIEN field. #define BR_SDHC_IRQSIGEN_CINTIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINTIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CINTIEN. #define BF_SDHC_IRQSIGEN_CINTIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CINTIEN), uint32_t) & BM_SDHC_IRQSIGEN_CINTIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CINTIEN field to a new value. #define BW_SDHC_IRQSIGEN_CINTIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CINTIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field CTOEIEN[16] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CTOEIEN (16U) //!< Bit position for SDHC_IRQSIGEN_CTOEIEN. #define BM_SDHC_IRQSIGEN_CTOEIEN (0x00010000U) //!< Bit mask for SDHC_IRQSIGEN_CTOEIEN. #define BS_SDHC_IRQSIGEN_CTOEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CTOEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CTOEIEN field. #define BR_SDHC_IRQSIGEN_CTOEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CTOEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CTOEIEN. #define BF_SDHC_IRQSIGEN_CTOEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CTOEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CTOEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CTOEIEN field to a new value. #define BW_SDHC_IRQSIGEN_CTOEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CTOEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field CCEIEN[17] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CCEIEN (17U) //!< Bit position for SDHC_IRQSIGEN_CCEIEN. #define BM_SDHC_IRQSIGEN_CCEIEN (0x00020000U) //!< Bit mask for SDHC_IRQSIGEN_CCEIEN. #define BS_SDHC_IRQSIGEN_CCEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CCEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CCEIEN field. #define BR_SDHC_IRQSIGEN_CCEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CCEIEN. #define BF_SDHC_IRQSIGEN_CCEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CCEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CCEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CCEIEN field to a new value. #define BW_SDHC_IRQSIGEN_CCEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CCEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field CEBEIEN[18] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CEBEIEN (18U) //!< Bit position for SDHC_IRQSIGEN_CEBEIEN. #define BM_SDHC_IRQSIGEN_CEBEIEN (0x00040000U) //!< Bit mask for SDHC_IRQSIGEN_CEBEIEN. #define BS_SDHC_IRQSIGEN_CEBEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CEBEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CEBEIEN field. #define BR_SDHC_IRQSIGEN_CEBEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CEBEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CEBEIEN. #define BF_SDHC_IRQSIGEN_CEBEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CEBEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CEBEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CEBEIEN field to a new value. #define BW_SDHC_IRQSIGEN_CEBEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CEBEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field CIEIEN[19] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_CIEIEN (19U) //!< Bit position for SDHC_IRQSIGEN_CIEIEN. #define BM_SDHC_IRQSIGEN_CIEIEN (0x00080000U) //!< Bit mask for SDHC_IRQSIGEN_CIEIEN. #define BS_SDHC_IRQSIGEN_CIEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_CIEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_CIEIEN field. #define BR_SDHC_IRQSIGEN_CIEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CIEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_CIEIEN. #define BF_SDHC_IRQSIGEN_CIEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_CIEIEN), uint32_t) & BM_SDHC_IRQSIGEN_CIEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the CIEIEN field to a new value. #define BW_SDHC_IRQSIGEN_CIEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_CIEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field DTOEIEN[20] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_DTOEIEN (20U) //!< Bit position for SDHC_IRQSIGEN_DTOEIEN. #define BM_SDHC_IRQSIGEN_DTOEIEN (0x00100000U) //!< Bit mask for SDHC_IRQSIGEN_DTOEIEN. #define BS_SDHC_IRQSIGEN_DTOEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DTOEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_DTOEIEN field. #define BR_SDHC_IRQSIGEN_DTOEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DTOEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_DTOEIEN. #define BF_SDHC_IRQSIGEN_DTOEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DTOEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DTOEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTOEIEN field to a new value. #define BW_SDHC_IRQSIGEN_DTOEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DTOEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field DCEIEN[21] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_DCEIEN (21U) //!< Bit position for SDHC_IRQSIGEN_DCEIEN. #define BM_SDHC_IRQSIGEN_DCEIEN (0x00200000U) //!< Bit mask for SDHC_IRQSIGEN_DCEIEN. #define BS_SDHC_IRQSIGEN_DCEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DCEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_DCEIEN field. #define BR_SDHC_IRQSIGEN_DCEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DCEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_DCEIEN. #define BF_SDHC_IRQSIGEN_DCEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DCEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DCEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DCEIEN field to a new value. #define BW_SDHC_IRQSIGEN_DCEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DCEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field DEBEIEN[22] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_DEBEIEN (22U) //!< Bit position for SDHC_IRQSIGEN_DEBEIEN. #define BM_SDHC_IRQSIGEN_DEBEIEN (0x00400000U) //!< Bit mask for SDHC_IRQSIGEN_DEBEIEN. #define BS_SDHC_IRQSIGEN_DEBEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DEBEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_DEBEIEN field. #define BR_SDHC_IRQSIGEN_DEBEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DEBEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_DEBEIEN. #define BF_SDHC_IRQSIGEN_DEBEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DEBEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DEBEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DEBEIEN field to a new value. #define BW_SDHC_IRQSIGEN_DEBEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DEBEIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field AC12EIEN[24] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_AC12EIEN (24U) //!< Bit position for SDHC_IRQSIGEN_AC12EIEN. #define BM_SDHC_IRQSIGEN_AC12EIEN (0x01000000U) //!< Bit mask for SDHC_IRQSIGEN_AC12EIEN. #define BS_SDHC_IRQSIGEN_AC12EIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_AC12EIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_AC12EIEN field. #define BR_SDHC_IRQSIGEN_AC12EIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_AC12EIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_AC12EIEN. #define BF_SDHC_IRQSIGEN_AC12EIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_AC12EIEN), uint32_t) & BM_SDHC_IRQSIGEN_AC12EIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12EIEN field to a new value. #define BW_SDHC_IRQSIGEN_AC12EIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_AC12EIEN) = (v)) #endif //@} /*! * @name Register SDHC_IRQSIGEN, field DMAEIEN[28] (RW) * * Values: * - 0 - Masked * - 1 - Enabled */ //@{ #define BP_SDHC_IRQSIGEN_DMAEIEN (28U) //!< Bit position for SDHC_IRQSIGEN_DMAEIEN. #define BM_SDHC_IRQSIGEN_DMAEIEN (0x10000000U) //!< Bit mask for SDHC_IRQSIGEN_DMAEIEN. #define BS_SDHC_IRQSIGEN_DMAEIEN (1U) //!< Bit field size in bits for SDHC_IRQSIGEN_DMAEIEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_IRQSIGEN_DMAEIEN field. #define BR_SDHC_IRQSIGEN_DMAEIEN (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DMAEIEN)) #endif //! @brief Format value for bitfield SDHC_IRQSIGEN_DMAEIEN. #define BF_SDHC_IRQSIGEN_DMAEIEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_IRQSIGEN_DMAEIEN), uint32_t) & BM_SDHC_IRQSIGEN_DMAEIEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the DMAEIEN field to a new value. #define BW_SDHC_IRQSIGEN_DMAEIEN(v) (BITBAND_ACCESS32(HW_SDHC_IRQSIGEN_ADDR, BP_SDHC_IRQSIGEN_DMAEIEN) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_AC12ERR - Auto CMD12 Error Status Register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_AC12ERR - Auto CMD12 Error Status Register (RO) * * Reset value: 0x00000000U * * When the AC12ESEN bit in the Status register is set, the host driver shall * check this register to identify what kind of error the Auto CMD12 indicated. * This register is valid only when the Auto CMD12 Error status bit is set. The * following table shows the relationship between the Auto CMGD12 CRC error and the * Auto CMD12 command timeout error. Relationship between Command CRC Error and * Command Timeout Error For Auto CMD12 Auto CMD12 CRC error Auto CMD12 timeout * error Type of error 0 0 No error 0 1 Response timeout error 1 0 Response CRC * error 1 1 CMD line conflict Changes in Auto CMD12 Error Status register can be * classified in three scenarios: When the SDHC is going to issue an Auto CMD12: Set * bit 0 to 1 if the Auto CMD12 can't be issued due to an error in the previous * command. Set bit 0 to 0 if the auto CMD12 is issued. At the end bit of an auto * CMD12 response: Check errors corresponding to bits 1-4. Set bits 1-4 * corresponding to detected errors. Clear bits 1-4 corresponding to detected errors. * Before reading the Auto CMD12 error status bit 7: Set bit 7 to 1 if there is a * command that can't be issued. Clear bit 7 if there is no command to issue. The * timing for generating the auto CMD12 error and writing to the command register * are asynchronous. After that, bit 7 shall be sampled when the driver is not * writing to the command register. So it is suggested to read this register only * when IRQSTAT[AC12E] is set. An Auto CMD12 error interrupt is generated when one * of the error bits (0-4) is set to 1. The command not issued by auto CMD12 * error does not generate an interrupt. */ typedef union _hw_sdhc_ac12err { uint32_t U; struct _hw_sdhc_ac12err_bitfields { uint32_t AC12NE : 1; //!< [0] Auto CMD12 Not Executed uint32_t AC12TOE : 1; //!< [1] Auto CMD12 Timeout Error uint32_t AC12EBE : 1; //!< [2] Auto CMD12 End Bit Error uint32_t AC12CE : 1; //!< [3] Auto CMD12 CRC Error uint32_t AC12IE : 1; //!< [4] Auto CMD12 Index Error uint32_t RESERVED0 : 2; //!< [6:5] uint32_t CNIBAC12E : 1; //!< [7] Command Not Issued By Auto CMD12 //! Error uint32_t RESERVED1 : 24; //!< [31:8] } B; } hw_sdhc_ac12err_t; #endif /*! * @name Constants and macros for entire SDHC_AC12ERR register */ //@{ #define HW_SDHC_AC12ERR_ADDR (REGS_SDHC_BASE + 0x3CU) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_AC12ERR (*(__I hw_sdhc_ac12err_t *) HW_SDHC_AC12ERR_ADDR) #define HW_SDHC_AC12ERR_RD() (HW_SDHC_AC12ERR.U) #endif //@} /* * Constants & macros for individual SDHC_AC12ERR bitfields */ /*! * @name Register SDHC_AC12ERR, field AC12NE[0] (RO) * * If memory multiple block data transfer is not started, due to a command * error, this bit is not set because it is not necessary to issue an auto CMD12. * Setting this bit to 1 means the SDHC cannot issue the auto CMD12 to stop a memory * multiple block data transfer due to some error. If this bit is set to 1, other * error status bits (1-4) have no meaning. * * Values: * - 0 - Executed. * - 1 - Not executed. */ //@{ #define BP_SDHC_AC12ERR_AC12NE (0U) //!< Bit position for SDHC_AC12ERR_AC12NE. #define BM_SDHC_AC12ERR_AC12NE (0x00000001U) //!< Bit mask for SDHC_AC12ERR_AC12NE. #define BS_SDHC_AC12ERR_AC12NE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12NE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_AC12ERR_AC12NE field. #define BR_SDHC_AC12ERR_AC12NE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12NE)) #endif //@} /*! * @name Register SDHC_AC12ERR, field AC12TOE[1] (RO) * * Occurs if no response is returned within 64 SDCLK cycles from the end bit of * the command. If this bit is set to 1, the other error status bits (2-4) have * no meaning. * * Values: * - 0 - No error. * - 1 - Time out. */ //@{ #define BP_SDHC_AC12ERR_AC12TOE (1U) //!< Bit position for SDHC_AC12ERR_AC12TOE. #define BM_SDHC_AC12ERR_AC12TOE (0x00000002U) //!< Bit mask for SDHC_AC12ERR_AC12TOE. #define BS_SDHC_AC12ERR_AC12TOE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12TOE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_AC12ERR_AC12TOE field. #define BR_SDHC_AC12ERR_AC12TOE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12TOE)) #endif //@} /*! * @name Register SDHC_AC12ERR, field AC12EBE[2] (RO) * * Occurs when detecting that the end bit of command response is 0 which must be * 1. * * Values: * - 0 - No error. * - 1 - End bit error generated. */ //@{ #define BP_SDHC_AC12ERR_AC12EBE (2U) //!< Bit position for SDHC_AC12ERR_AC12EBE. #define BM_SDHC_AC12ERR_AC12EBE (0x00000004U) //!< Bit mask for SDHC_AC12ERR_AC12EBE. #define BS_SDHC_AC12ERR_AC12EBE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12EBE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_AC12ERR_AC12EBE field. #define BR_SDHC_AC12ERR_AC12EBE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12EBE)) #endif //@} /*! * @name Register SDHC_AC12ERR, field AC12CE[3] (RO) * * Occurs when detecting a CRC error in the command response. * * Values: * - 0 - No CRC error. * - 1 - CRC error met in Auto CMD12 response. */ //@{ #define BP_SDHC_AC12ERR_AC12CE (3U) //!< Bit position for SDHC_AC12ERR_AC12CE. #define BM_SDHC_AC12ERR_AC12CE (0x00000008U) //!< Bit mask for SDHC_AC12ERR_AC12CE. #define BS_SDHC_AC12ERR_AC12CE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12CE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_AC12ERR_AC12CE field. #define BR_SDHC_AC12ERR_AC12CE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12CE)) #endif //@} /*! * @name Register SDHC_AC12ERR, field AC12IE[4] (RO) * * Occurs if the command index error occurs in response to a command. * * Values: * - 0 - No error. * - 1 - Error, the CMD index in response is not CMD12. */ //@{ #define BP_SDHC_AC12ERR_AC12IE (4U) //!< Bit position for SDHC_AC12ERR_AC12IE. #define BM_SDHC_AC12ERR_AC12IE (0x00000010U) //!< Bit mask for SDHC_AC12ERR_AC12IE. #define BS_SDHC_AC12ERR_AC12IE (1U) //!< Bit field size in bits for SDHC_AC12ERR_AC12IE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_AC12ERR_AC12IE field. #define BR_SDHC_AC12ERR_AC12IE (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_AC12IE)) #endif //@} /*! * @name Register SDHC_AC12ERR, field CNIBAC12E[7] (RO) * * Setting this bit to 1 means CMD_wo_DAT is not executed due to an auto CMD12 * error (D04-D01) in this register. * * Values: * - 0 - No error. * - 1 - Not issued. */ //@{ #define BP_SDHC_AC12ERR_CNIBAC12E (7U) //!< Bit position for SDHC_AC12ERR_CNIBAC12E. #define BM_SDHC_AC12ERR_CNIBAC12E (0x00000080U) //!< Bit mask for SDHC_AC12ERR_CNIBAC12E. #define BS_SDHC_AC12ERR_CNIBAC12E (1U) //!< Bit field size in bits for SDHC_AC12ERR_CNIBAC12E. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_AC12ERR_CNIBAC12E field. #define BR_SDHC_AC12ERR_CNIBAC12E (BITBAND_ACCESS32(HW_SDHC_AC12ERR_ADDR, BP_SDHC_AC12ERR_CNIBAC12E)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_HTCAPBLT - Host Controller Capabilities //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_HTCAPBLT - Host Controller Capabilities (RO) * * Reset value: 0x07F30000U * * This register provides the host driver with information specific to the SDHC * implementation. The value in this register is the power-on-reset value, and * does not change with a software reset. Any write to this register is ignored. */ typedef union _hw_sdhc_htcapblt { uint32_t U; struct _hw_sdhc_htcapblt_bitfields { uint32_t RESERVED0 : 16; //!< [15:0] uint32_t MBL : 3; //!< [18:16] Max Block Length uint32_t RESERVED1 : 1; //!< [19] uint32_t ADMAS : 1; //!< [20] ADMA Support uint32_t HSS : 1; //!< [21] High Speed Support uint32_t DMAS : 1; //!< [22] DMA Support uint32_t SRS : 1; //!< [23] Suspend/Resume Support uint32_t VS33 : 1; //!< [24] Voltage Support 3.3 V uint32_t RESERVED2 : 7; //!< [31:25] } B; } hw_sdhc_htcapblt_t; #endif /*! * @name Constants and macros for entire SDHC_HTCAPBLT register */ //@{ #define HW_SDHC_HTCAPBLT_ADDR (REGS_SDHC_BASE + 0x40U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_HTCAPBLT (*(__I hw_sdhc_htcapblt_t *) HW_SDHC_HTCAPBLT_ADDR) #define HW_SDHC_HTCAPBLT_RD() (HW_SDHC_HTCAPBLT.U) #endif //@} /* * Constants & macros for individual SDHC_HTCAPBLT bitfields */ /*! * @name Register SDHC_HTCAPBLT, field MBL[18:16] (RO) * * This value indicates the maximum block size that the host driver can read and * write to the buffer in the SDHC. The buffer shall transfer block size without * wait cycles. * * Values: * - 000 - 512 bytes * - 001 - 1024 bytes * - 010 - 2048 bytes * - 011 - 4096 bytes */ //@{ #define BP_SDHC_HTCAPBLT_MBL (16U) //!< Bit position for SDHC_HTCAPBLT_MBL. #define BM_SDHC_HTCAPBLT_MBL (0x00070000U) //!< Bit mask for SDHC_HTCAPBLT_MBL. #define BS_SDHC_HTCAPBLT_MBL (3U) //!< Bit field size in bits for SDHC_HTCAPBLT_MBL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HTCAPBLT_MBL field. #define BR_SDHC_HTCAPBLT_MBL (HW_SDHC_HTCAPBLT.B.MBL) #endif //@} /*! * @name Register SDHC_HTCAPBLT, field ADMAS[20] (RO) * * This bit indicates whether the SDHC supports the ADMA feature. * * Values: * - 0 - Advanced DMA not supported. * - 1 - Advanced DMA supported. */ //@{ #define BP_SDHC_HTCAPBLT_ADMAS (20U) //!< Bit position for SDHC_HTCAPBLT_ADMAS. #define BM_SDHC_HTCAPBLT_ADMAS (0x00100000U) //!< Bit mask for SDHC_HTCAPBLT_ADMAS. #define BS_SDHC_HTCAPBLT_ADMAS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_ADMAS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HTCAPBLT_ADMAS field. #define BR_SDHC_HTCAPBLT_ADMAS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_ADMAS)) #endif //@} /*! * @name Register SDHC_HTCAPBLT, field HSS[21] (RO) * * This bit indicates whether the SDHC supports high speed mode and the host * system can supply a SD Clock frequency from 25 MHz to 50 MHz. * * Values: * - 0 - High speed not supported. * - 1 - High speed supported. */ //@{ #define BP_SDHC_HTCAPBLT_HSS (21U) //!< Bit position for SDHC_HTCAPBLT_HSS. #define BM_SDHC_HTCAPBLT_HSS (0x00200000U) //!< Bit mask for SDHC_HTCAPBLT_HSS. #define BS_SDHC_HTCAPBLT_HSS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_HSS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HTCAPBLT_HSS field. #define BR_SDHC_HTCAPBLT_HSS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_HSS)) #endif //@} /*! * @name Register SDHC_HTCAPBLT, field DMAS[22] (RO) * * This bit indicates whether the SDHC is capable of using the internal DMA to * transfer data between system memory and the data buffer directly. * * Values: * - 0 - DMA not supported. * - 1 - DMA supported. */ //@{ #define BP_SDHC_HTCAPBLT_DMAS (22U) //!< Bit position for SDHC_HTCAPBLT_DMAS. #define BM_SDHC_HTCAPBLT_DMAS (0x00400000U) //!< Bit mask for SDHC_HTCAPBLT_DMAS. #define BS_SDHC_HTCAPBLT_DMAS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_DMAS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HTCAPBLT_DMAS field. #define BR_SDHC_HTCAPBLT_DMAS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_DMAS)) #endif //@} /*! * @name Register SDHC_HTCAPBLT, field SRS[23] (RO) * * This bit indicates whether the SDHC supports suspend / resume functionality. * If this bit is 0, the suspend and resume mechanism, as well as the read Wwait, * are not supported, and the host driver shall not issue either suspend or * resume commands. * * Values: * - 0 - Not supported. * - 1 - Supported. */ //@{ #define BP_SDHC_HTCAPBLT_SRS (23U) //!< Bit position for SDHC_HTCAPBLT_SRS. #define BM_SDHC_HTCAPBLT_SRS (0x00800000U) //!< Bit mask for SDHC_HTCAPBLT_SRS. #define BS_SDHC_HTCAPBLT_SRS (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_SRS. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HTCAPBLT_SRS field. #define BR_SDHC_HTCAPBLT_SRS (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_SRS)) #endif //@} /*! * @name Register SDHC_HTCAPBLT, field VS33[24] (RO) * * This bit shall depend on the host system ability. * * Values: * - 0 - 3.3 V not supported. * - 1 - 3.3 V supported. */ //@{ #define BP_SDHC_HTCAPBLT_VS33 (24U) //!< Bit position for SDHC_HTCAPBLT_VS33. #define BM_SDHC_HTCAPBLT_VS33 (0x01000000U) //!< Bit mask for SDHC_HTCAPBLT_VS33. #define BS_SDHC_HTCAPBLT_VS33 (1U) //!< Bit field size in bits for SDHC_HTCAPBLT_VS33. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HTCAPBLT_VS33 field. #define BR_SDHC_HTCAPBLT_VS33 (BITBAND_ACCESS32(HW_SDHC_HTCAPBLT_ADDR, BP_SDHC_HTCAPBLT_VS33)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_WML - Watermark Level Register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_WML - Watermark Level Register (RW) * * Reset value: 0x00100010U * * Both write and read watermark levels (FIFO threshold) are configurable. There * value can range from 1 to 128 words. Both write and read burst lengths are * also configurable. There value can range from 1 to 31 words. */ typedef union _hw_sdhc_wml { uint32_t U; struct _hw_sdhc_wml_bitfields { uint32_t RDWML : 8; //!< [7:0] Read Watermark Level uint32_t RESERVED0 : 8; //!< [15:8] uint32_t WRWML : 8; //!< [23:16] Write Watermark Level uint32_t RESERVED1 : 8; //!< [31:24] } B; } hw_sdhc_wml_t; #endif /*! * @name Constants and macros for entire SDHC_WML register */ //@{ #define HW_SDHC_WML_ADDR (REGS_SDHC_BASE + 0x44U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_WML (*(__IO hw_sdhc_wml_t *) HW_SDHC_WML_ADDR) #define HW_SDHC_WML_RD() (HW_SDHC_WML.U) #define HW_SDHC_WML_WR(v) (HW_SDHC_WML.U = (v)) #define HW_SDHC_WML_SET(v) (HW_SDHC_WML_WR(HW_SDHC_WML_RD() | (v))) #define HW_SDHC_WML_CLR(v) (HW_SDHC_WML_WR(HW_SDHC_WML_RD() & ~(v))) #define HW_SDHC_WML_TOG(v) (HW_SDHC_WML_WR(HW_SDHC_WML_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_WML bitfields */ /*! * @name Register SDHC_WML, field RDWML[7:0] (RW) * * The number of words used as the watermark level (FIFO threshold) in a DMA * read operation. Also the number of words as a sequence of read bursts in * back-to-back mode. The maximum legal value for the read water mark level is 128. */ //@{ #define BP_SDHC_WML_RDWML (0U) //!< Bit position for SDHC_WML_RDWML. #define BM_SDHC_WML_RDWML (0x000000FFU) //!< Bit mask for SDHC_WML_RDWML. #define BS_SDHC_WML_RDWML (8U) //!< Bit field size in bits for SDHC_WML_RDWML. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_WML_RDWML field. #define BR_SDHC_WML_RDWML (HW_SDHC_WML.B.RDWML) #endif //! @brief Format value for bitfield SDHC_WML_RDWML. #define BF_SDHC_WML_RDWML(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_WML_RDWML), uint32_t) & BM_SDHC_WML_RDWML) #ifndef __LANGUAGE_ASM__ //! @brief Set the RDWML field to a new value. #define BW_SDHC_WML_RDWML(v) (HW_SDHC_WML_WR((HW_SDHC_WML_RD() & ~BM_SDHC_WML_RDWML) | BF_SDHC_WML_RDWML(v))) #endif //@} /*! * @name Register SDHC_WML, field WRWML[23:16] (RW) * * The number of words used as the watermark level (FIFO threshold) in a DMA * write operation. Also the number of words as a sequence of write bursts in * back-to-back mode. The maximum legal value for the write watermark level is 128. */ //@{ #define BP_SDHC_WML_WRWML (16U) //!< Bit position for SDHC_WML_WRWML. #define BM_SDHC_WML_WRWML (0x00FF0000U) //!< Bit mask for SDHC_WML_WRWML. #define BS_SDHC_WML_WRWML (8U) //!< Bit field size in bits for SDHC_WML_WRWML. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_WML_WRWML field. #define BR_SDHC_WML_WRWML (HW_SDHC_WML.B.WRWML) #endif //! @brief Format value for bitfield SDHC_WML_WRWML. #define BF_SDHC_WML_WRWML(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_WML_WRWML), uint32_t) & BM_SDHC_WML_WRWML) #ifndef __LANGUAGE_ASM__ //! @brief Set the WRWML field to a new value. #define BW_SDHC_WML_WRWML(v) (HW_SDHC_WML_WR((HW_SDHC_WML_RD() & ~BM_SDHC_WML_WRWML) | BF_SDHC_WML_WRWML(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_FEVT - Force Event register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_FEVT - Force Event register (WO) * * Reset value: 0x00000000U * * The Force Event (FEVT) register is not a physically implemented register. * Rather, it is an address at which the Interrupt Status register can be written if * the corresponding bit of the Interrupt Status Enable register is set. This * register is a write only register and writing 0 to it has no effect. Writing 1 * to this register actually sets the corresponding bit of Interrupt Status * register. A read from this register always results in 0's. To change the * corresponding status bits in the interrupt status register, make sure to set * SYSCTL[IPGEN] so that bus clock is always active. Forcing a card interrupt will generate a * short pulse on the DAT[1] line, and the driver may treat this interrupt as a * normal interrupt. The interrupt service routine may skip polling the card * interrupt factor as the interrupt is selfcleared. */ typedef union _hw_sdhc_fevt { uint32_t U; struct _hw_sdhc_fevt_bitfields { uint32_t AC12NE : 1; //!< [0] Force Event Auto Command 12 Not Executed uint32_t AC12TOE : 1; //!< [1] Force Event Auto Command 12 Time Out //! Error uint32_t AC12CE : 1; //!< [2] Force Event Auto Command 12 CRC Error uint32_t AC12EBE : 1; //!< [3] Force Event Auto Command 12 End Bit //! Error uint32_t AC12IE : 1; //!< [4] Force Event Auto Command 12 Index Error uint32_t RESERVED0 : 2; //!< [6:5] uint32_t CNIBAC12E : 1; //!< [7] Force Event Command Not Executed By //! Auto Command 12 Error uint32_t RESERVED1 : 8; //!< [15:8] uint32_t CTOE : 1; //!< [16] Force Event Command Time Out Error uint32_t CCE : 1; //!< [17] Force Event Command CRC Error uint32_t CEBE : 1; //!< [18] Force Event Command End Bit Error uint32_t CIE : 1; //!< [19] Force Event Command Index Error uint32_t DTOE : 1; //!< [20] Force Event Data Time Out Error uint32_t DCE : 1; //!< [21] Force Event Data CRC Error uint32_t DEBE : 1; //!< [22] Force Event Data End Bit Error uint32_t RESERVED2 : 1; //!< [23] uint32_t AC12E : 1; //!< [24] Force Event Auto Command 12 Error uint32_t RESERVED3 : 3; //!< [27:25] uint32_t DMAE : 1; //!< [28] Force Event DMA Error uint32_t RESERVED4 : 2; //!< [30:29] uint32_t CINT : 1; //!< [31] Force Event Card Interrupt } B; } hw_sdhc_fevt_t; #endif /*! * @name Constants and macros for entire SDHC_FEVT register */ //@{ #define HW_SDHC_FEVT_ADDR (REGS_SDHC_BASE + 0x50U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_FEVT (*(__O hw_sdhc_fevt_t *) HW_SDHC_FEVT_ADDR) #define HW_SDHC_FEVT_RD() (HW_SDHC_FEVT.U) #define HW_SDHC_FEVT_WR(v) (HW_SDHC_FEVT.U = (v)) #endif //@} /* * Constants & macros for individual SDHC_FEVT bitfields */ /*! * @name Register SDHC_FEVT, field AC12NE[0] (WORZ) * * Forces AC12ERR[AC12NE] to be set. */ //@{ #define BP_SDHC_FEVT_AC12NE (0U) //!< Bit position for SDHC_FEVT_AC12NE. #define BM_SDHC_FEVT_AC12NE (0x00000001U) //!< Bit mask for SDHC_FEVT_AC12NE. #define BS_SDHC_FEVT_AC12NE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12NE. //! @brief Format value for bitfield SDHC_FEVT_AC12NE. #define BF_SDHC_FEVT_AC12NE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12NE), uint32_t) & BM_SDHC_FEVT_AC12NE) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12NE field to a new value. #define BW_SDHC_FEVT_AC12NE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12NE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field AC12TOE[1] (WORZ) * * Forces AC12ERR[AC12TOE] to be set. */ //@{ #define BP_SDHC_FEVT_AC12TOE (1U) //!< Bit position for SDHC_FEVT_AC12TOE. #define BM_SDHC_FEVT_AC12TOE (0x00000002U) //!< Bit mask for SDHC_FEVT_AC12TOE. #define BS_SDHC_FEVT_AC12TOE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12TOE. //! @brief Format value for bitfield SDHC_FEVT_AC12TOE. #define BF_SDHC_FEVT_AC12TOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12TOE), uint32_t) & BM_SDHC_FEVT_AC12TOE) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12TOE field to a new value. #define BW_SDHC_FEVT_AC12TOE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12TOE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field AC12CE[2] (WORZ) * * Forces AC12ERR[AC12CE] to be set. */ //@{ #define BP_SDHC_FEVT_AC12CE (2U) //!< Bit position for SDHC_FEVT_AC12CE. #define BM_SDHC_FEVT_AC12CE (0x00000004U) //!< Bit mask for SDHC_FEVT_AC12CE. #define BS_SDHC_FEVT_AC12CE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12CE. //! @brief Format value for bitfield SDHC_FEVT_AC12CE. #define BF_SDHC_FEVT_AC12CE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12CE), uint32_t) & BM_SDHC_FEVT_AC12CE) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12CE field to a new value. #define BW_SDHC_FEVT_AC12CE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12CE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field AC12EBE[3] (WORZ) * * Forces AC12ERR[AC12EBE] to be set. */ //@{ #define BP_SDHC_FEVT_AC12EBE (3U) //!< Bit position for SDHC_FEVT_AC12EBE. #define BM_SDHC_FEVT_AC12EBE (0x00000008U) //!< Bit mask for SDHC_FEVT_AC12EBE. #define BS_SDHC_FEVT_AC12EBE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12EBE. //! @brief Format value for bitfield SDHC_FEVT_AC12EBE. #define BF_SDHC_FEVT_AC12EBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12EBE), uint32_t) & BM_SDHC_FEVT_AC12EBE) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12EBE field to a new value. #define BW_SDHC_FEVT_AC12EBE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12EBE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field AC12IE[4] (WORZ) * * Forces AC12ERR[AC12IE] to be set. */ //@{ #define BP_SDHC_FEVT_AC12IE (4U) //!< Bit position for SDHC_FEVT_AC12IE. #define BM_SDHC_FEVT_AC12IE (0x00000010U) //!< Bit mask for SDHC_FEVT_AC12IE. #define BS_SDHC_FEVT_AC12IE (1U) //!< Bit field size in bits for SDHC_FEVT_AC12IE. //! @brief Format value for bitfield SDHC_FEVT_AC12IE. #define BF_SDHC_FEVT_AC12IE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12IE), uint32_t) & BM_SDHC_FEVT_AC12IE) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12IE field to a new value. #define BW_SDHC_FEVT_AC12IE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12IE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field CNIBAC12E[7] (WORZ) * * Forces AC12ERR[CNIBAC12E] to be set. */ //@{ #define BP_SDHC_FEVT_CNIBAC12E (7U) //!< Bit position for SDHC_FEVT_CNIBAC12E. #define BM_SDHC_FEVT_CNIBAC12E (0x00000080U) //!< Bit mask for SDHC_FEVT_CNIBAC12E. #define BS_SDHC_FEVT_CNIBAC12E (1U) //!< Bit field size in bits for SDHC_FEVT_CNIBAC12E. //! @brief Format value for bitfield SDHC_FEVT_CNIBAC12E. #define BF_SDHC_FEVT_CNIBAC12E(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CNIBAC12E), uint32_t) & BM_SDHC_FEVT_CNIBAC12E) #ifndef __LANGUAGE_ASM__ //! @brief Set the CNIBAC12E field to a new value. #define BW_SDHC_FEVT_CNIBAC12E(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CNIBAC12E) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field CTOE[16] (WORZ) * * Forces IRQSTAT[CTOE] to be set. */ //@{ #define BP_SDHC_FEVT_CTOE (16U) //!< Bit position for SDHC_FEVT_CTOE. #define BM_SDHC_FEVT_CTOE (0x00010000U) //!< Bit mask for SDHC_FEVT_CTOE. #define BS_SDHC_FEVT_CTOE (1U) //!< Bit field size in bits for SDHC_FEVT_CTOE. //! @brief Format value for bitfield SDHC_FEVT_CTOE. #define BF_SDHC_FEVT_CTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CTOE), uint32_t) & BM_SDHC_FEVT_CTOE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CTOE field to a new value. #define BW_SDHC_FEVT_CTOE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CTOE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field CCE[17] (WORZ) * * Forces IRQSTAT[CCE] to be set. */ //@{ #define BP_SDHC_FEVT_CCE (17U) //!< Bit position for SDHC_FEVT_CCE. #define BM_SDHC_FEVT_CCE (0x00020000U) //!< Bit mask for SDHC_FEVT_CCE. #define BS_SDHC_FEVT_CCE (1U) //!< Bit field size in bits for SDHC_FEVT_CCE. //! @brief Format value for bitfield SDHC_FEVT_CCE. #define BF_SDHC_FEVT_CCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CCE), uint32_t) & BM_SDHC_FEVT_CCE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CCE field to a new value. #define BW_SDHC_FEVT_CCE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CCE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field CEBE[18] (WORZ) * * Forces IRQSTAT[CEBE] to be set. */ //@{ #define BP_SDHC_FEVT_CEBE (18U) //!< Bit position for SDHC_FEVT_CEBE. #define BM_SDHC_FEVT_CEBE (0x00040000U) //!< Bit mask for SDHC_FEVT_CEBE. #define BS_SDHC_FEVT_CEBE (1U) //!< Bit field size in bits for SDHC_FEVT_CEBE. //! @brief Format value for bitfield SDHC_FEVT_CEBE. #define BF_SDHC_FEVT_CEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CEBE), uint32_t) & BM_SDHC_FEVT_CEBE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CEBE field to a new value. #define BW_SDHC_FEVT_CEBE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CEBE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field CIE[19] (WORZ) * * Forces IRQSTAT[CCE] to be set. */ //@{ #define BP_SDHC_FEVT_CIE (19U) //!< Bit position for SDHC_FEVT_CIE. #define BM_SDHC_FEVT_CIE (0x00080000U) //!< Bit mask for SDHC_FEVT_CIE. #define BS_SDHC_FEVT_CIE (1U) //!< Bit field size in bits for SDHC_FEVT_CIE. //! @brief Format value for bitfield SDHC_FEVT_CIE. #define BF_SDHC_FEVT_CIE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CIE), uint32_t) & BM_SDHC_FEVT_CIE) #ifndef __LANGUAGE_ASM__ //! @brief Set the CIE field to a new value. #define BW_SDHC_FEVT_CIE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CIE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field DTOE[20] (WORZ) * * Forces IRQSTAT[DTOE] to be set. */ //@{ #define BP_SDHC_FEVT_DTOE (20U) //!< Bit position for SDHC_FEVT_DTOE. #define BM_SDHC_FEVT_DTOE (0x00100000U) //!< Bit mask for SDHC_FEVT_DTOE. #define BS_SDHC_FEVT_DTOE (1U) //!< Bit field size in bits for SDHC_FEVT_DTOE. //! @brief Format value for bitfield SDHC_FEVT_DTOE. #define BF_SDHC_FEVT_DTOE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DTOE), uint32_t) & BM_SDHC_FEVT_DTOE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTOE field to a new value. #define BW_SDHC_FEVT_DTOE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DTOE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field DCE[21] (WORZ) * * Forces IRQSTAT[DCE] to be set. */ //@{ #define BP_SDHC_FEVT_DCE (21U) //!< Bit position for SDHC_FEVT_DCE. #define BM_SDHC_FEVT_DCE (0x00200000U) //!< Bit mask for SDHC_FEVT_DCE. #define BS_SDHC_FEVT_DCE (1U) //!< Bit field size in bits for SDHC_FEVT_DCE. //! @brief Format value for bitfield SDHC_FEVT_DCE. #define BF_SDHC_FEVT_DCE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DCE), uint32_t) & BM_SDHC_FEVT_DCE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DCE field to a new value. #define BW_SDHC_FEVT_DCE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DCE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field DEBE[22] (WORZ) * * Forces IRQSTAT[DEBE] to be set. */ //@{ #define BP_SDHC_FEVT_DEBE (22U) //!< Bit position for SDHC_FEVT_DEBE. #define BM_SDHC_FEVT_DEBE (0x00400000U) //!< Bit mask for SDHC_FEVT_DEBE. #define BS_SDHC_FEVT_DEBE (1U) //!< Bit field size in bits for SDHC_FEVT_DEBE. //! @brief Format value for bitfield SDHC_FEVT_DEBE. #define BF_SDHC_FEVT_DEBE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DEBE), uint32_t) & BM_SDHC_FEVT_DEBE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DEBE field to a new value. #define BW_SDHC_FEVT_DEBE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DEBE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field AC12E[24] (WORZ) * * Forces IRQSTAT[AC12E] to be set. */ //@{ #define BP_SDHC_FEVT_AC12E (24U) //!< Bit position for SDHC_FEVT_AC12E. #define BM_SDHC_FEVT_AC12E (0x01000000U) //!< Bit mask for SDHC_FEVT_AC12E. #define BS_SDHC_FEVT_AC12E (1U) //!< Bit field size in bits for SDHC_FEVT_AC12E. //! @brief Format value for bitfield SDHC_FEVT_AC12E. #define BF_SDHC_FEVT_AC12E(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_AC12E), uint32_t) & BM_SDHC_FEVT_AC12E) #ifndef __LANGUAGE_ASM__ //! @brief Set the AC12E field to a new value. #define BW_SDHC_FEVT_AC12E(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_AC12E) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field DMAE[28] (WORZ) * * Forces the DMAE bit of Interrupt Status Register to be set. */ //@{ #define BP_SDHC_FEVT_DMAE (28U) //!< Bit position for SDHC_FEVT_DMAE. #define BM_SDHC_FEVT_DMAE (0x10000000U) //!< Bit mask for SDHC_FEVT_DMAE. #define BS_SDHC_FEVT_DMAE (1U) //!< Bit field size in bits for SDHC_FEVT_DMAE. //! @brief Format value for bitfield SDHC_FEVT_DMAE. #define BF_SDHC_FEVT_DMAE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_DMAE), uint32_t) & BM_SDHC_FEVT_DMAE) #ifndef __LANGUAGE_ASM__ //! @brief Set the DMAE field to a new value. #define BW_SDHC_FEVT_DMAE(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_DMAE) = (v)) #endif //@} /*! * @name Register SDHC_FEVT, field CINT[31] (WORZ) * * Writing 1 to this bit generates a short low-level pulse on the internal * DAT[1] line, as if a self-clearing interrupt was received from the external card. * If enabled, the CINT bit will be set and the interrupt service routine may * treat this interrupt as a normal interrupt from the external card. */ //@{ #define BP_SDHC_FEVT_CINT (31U) //!< Bit position for SDHC_FEVT_CINT. #define BM_SDHC_FEVT_CINT (0x80000000U) //!< Bit mask for SDHC_FEVT_CINT. #define BS_SDHC_FEVT_CINT (1U) //!< Bit field size in bits for SDHC_FEVT_CINT. //! @brief Format value for bitfield SDHC_FEVT_CINT. #define BF_SDHC_FEVT_CINT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_FEVT_CINT), uint32_t) & BM_SDHC_FEVT_CINT) #ifndef __LANGUAGE_ASM__ //! @brief Set the CINT field to a new value. #define BW_SDHC_FEVT_CINT(v) (BITBAND_ACCESS32(HW_SDHC_FEVT_ADDR, BP_SDHC_FEVT_CINT) = (v)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_ADMAES - ADMA Error Status register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_ADMAES - ADMA Error Status register (RO) * * Reset value: 0x00000000U * * When an ADMA error interrupt has occurred, the ADMA Error States field in * this register holds the ADMA state and the ADMA System Address register holds the * address around the error descriptor. For recovering from this error, the host * driver requires the ADMA state to identify the error descriptor address as * follows: ST_STOP: Previous location set in the ADMA System Address register is * the error descriptor address. ST_FDS: Current location set in the ADMA System * Address register is the error descriptor address. ST_CADR: This state is never * set because it only increments the descriptor pointer and doesn't generate an * ADMA error. ST_TFR: Previous location set in the ADMA System Address register * is the error descriptor address. In case of a write operation, the host driver * must use the ACMD22 to get the number of the written block, rather than using * this information, because unwritten data may exist in the host controller. * The host controller generates the ADMA error interrupt when it detects invalid * descriptor data (valid = 0) in the ST_FDS state. The host driver can * distinguish this error by reading the valid bit of the error descriptor. ADMA Error * State coding D01-D00 ADMA Error State when error has occurred Contents of ADMA * System Address register 00 ST_STOP (Stop DMA) Holds the address of the next * executable descriptor command 01 ST_FDS (fetch descriptor) Holds the valid * descriptor address 10 ST_CADR (change address) No ADMA error is generated 11 ST_TFR * (Transfer Data) Holds the address of the next executable descriptor command */ typedef union _hw_sdhc_admaes { uint32_t U; struct _hw_sdhc_admaes_bitfields { uint32_t ADMAES : 2; //!< [1:0] ADMA Error State (When ADMA Error Is //! Occurred.) uint32_t ADMALME : 1; //!< [2] ADMA Length Mismatch Error uint32_t ADMADCE : 1; //!< [3] ADMA Descriptor Error uint32_t RESERVED0 : 28; //!< [31:4] } B; } hw_sdhc_admaes_t; #endif /*! * @name Constants and macros for entire SDHC_ADMAES register */ //@{ #define HW_SDHC_ADMAES_ADDR (REGS_SDHC_BASE + 0x54U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_ADMAES (*(__I hw_sdhc_admaes_t *) HW_SDHC_ADMAES_ADDR) #define HW_SDHC_ADMAES_RD() (HW_SDHC_ADMAES.U) #endif //@} /* * Constants & macros for individual SDHC_ADMAES bitfields */ /*! * @name Register SDHC_ADMAES, field ADMAES[1:0] (RO) * * Indicates the state of the ADMA when an error has occurred during an ADMA * data transfer. */ //@{ #define BP_SDHC_ADMAES_ADMAES (0U) //!< Bit position for SDHC_ADMAES_ADMAES. #define BM_SDHC_ADMAES_ADMAES (0x00000003U) //!< Bit mask for SDHC_ADMAES_ADMAES. #define BS_SDHC_ADMAES_ADMAES (2U) //!< Bit field size in bits for SDHC_ADMAES_ADMAES. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_ADMAES_ADMAES field. #define BR_SDHC_ADMAES_ADMAES (HW_SDHC_ADMAES.B.ADMAES) #endif //@} /*! * @name Register SDHC_ADMAES, field ADMALME[2] (RO) * * This error occurs in the following 2 cases: While the block count enable is * being set, the total data length specified by the descriptor table is different * from that specified by the block count and block length. Total data length * can not be divided by the block length. * * Values: * - 0 - No error. * - 1 - Error. */ //@{ #define BP_SDHC_ADMAES_ADMALME (2U) //!< Bit position for SDHC_ADMAES_ADMALME. #define BM_SDHC_ADMAES_ADMALME (0x00000004U) //!< Bit mask for SDHC_ADMAES_ADMALME. #define BS_SDHC_ADMAES_ADMALME (1U) //!< Bit field size in bits for SDHC_ADMAES_ADMALME. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_ADMAES_ADMALME field. #define BR_SDHC_ADMAES_ADMALME (BITBAND_ACCESS32(HW_SDHC_ADMAES_ADDR, BP_SDHC_ADMAES_ADMALME)) #endif //@} /*! * @name Register SDHC_ADMAES, field ADMADCE[3] (RO) * * This error occurs when an invalid descriptor is fetched by ADMA. * * Values: * - 0 - No error. * - 1 - Error. */ //@{ #define BP_SDHC_ADMAES_ADMADCE (3U) //!< Bit position for SDHC_ADMAES_ADMADCE. #define BM_SDHC_ADMAES_ADMADCE (0x00000008U) //!< Bit mask for SDHC_ADMAES_ADMADCE. #define BS_SDHC_ADMAES_ADMADCE (1U) //!< Bit field size in bits for SDHC_ADMAES_ADMADCE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_ADMAES_ADMADCE field. #define BR_SDHC_ADMAES_ADMADCE (BITBAND_ACCESS32(HW_SDHC_ADMAES_ADDR, BP_SDHC_ADMAES_ADMADCE)) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_ADSADDR - ADMA System Addressregister //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_ADSADDR - ADMA System Addressregister (RW) * * Reset value: 0x00000000U * * This register contains the physical system memory address used for ADMA * transfers. */ typedef union _hw_sdhc_adsaddr { uint32_t U; struct _hw_sdhc_adsaddr_bitfields { uint32_t RESERVED0 : 2; //!< [1:0] uint32_t ADSADDR : 30; //!< [31:2] ADMA System Address } B; } hw_sdhc_adsaddr_t; #endif /*! * @name Constants and macros for entire SDHC_ADSADDR register */ //@{ #define HW_SDHC_ADSADDR_ADDR (REGS_SDHC_BASE + 0x58U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_ADSADDR (*(__IO hw_sdhc_adsaddr_t *) HW_SDHC_ADSADDR_ADDR) #define HW_SDHC_ADSADDR_RD() (HW_SDHC_ADSADDR.U) #define HW_SDHC_ADSADDR_WR(v) (HW_SDHC_ADSADDR.U = (v)) #define HW_SDHC_ADSADDR_SET(v) (HW_SDHC_ADSADDR_WR(HW_SDHC_ADSADDR_RD() | (v))) #define HW_SDHC_ADSADDR_CLR(v) (HW_SDHC_ADSADDR_WR(HW_SDHC_ADSADDR_RD() & ~(v))) #define HW_SDHC_ADSADDR_TOG(v) (HW_SDHC_ADSADDR_WR(HW_SDHC_ADSADDR_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_ADSADDR bitfields */ /*! * @name Register SDHC_ADSADDR, field ADSADDR[31:2] (RW) * * Holds the word address of the executing command in the descriptor table. At * the start of ADMA, the host driver shall set the start address of the * Descriptor table. The ADMA engine increments this register address whenever fetching a * descriptor command. When the ADMA is stopped at the block gap, this register * indicates the address of the next executable descriptor command. When the ADMA * error interrupt is generated, this register shall hold the valid descriptor * address depending on the ADMA state. The lower 2 bits of this register is tied * to '0' so the ADMA address is always word-aligned. Because this register * supports dynamic address reflecting, when TC bit is set, it automatically alters the * value of internal address counter, so SW cannot change this register when TC * bit is set. */ //@{ #define BP_SDHC_ADSADDR_ADSADDR (2U) //!< Bit position for SDHC_ADSADDR_ADSADDR. #define BM_SDHC_ADSADDR_ADSADDR (0xFFFFFFFCU) //!< Bit mask for SDHC_ADSADDR_ADSADDR. #define BS_SDHC_ADSADDR_ADSADDR (30U) //!< Bit field size in bits for SDHC_ADSADDR_ADSADDR. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_ADSADDR_ADSADDR field. #define BR_SDHC_ADSADDR_ADSADDR (HW_SDHC_ADSADDR.B.ADSADDR) #endif //! @brief Format value for bitfield SDHC_ADSADDR_ADSADDR. #define BF_SDHC_ADSADDR_ADSADDR(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_ADSADDR_ADSADDR), uint32_t) & BM_SDHC_ADSADDR_ADSADDR) #ifndef __LANGUAGE_ASM__ //! @brief Set the ADSADDR field to a new value. #define BW_SDHC_ADSADDR_ADSADDR(v) (HW_SDHC_ADSADDR_WR((HW_SDHC_ADSADDR_RD() & ~BM_SDHC_ADSADDR_ADSADDR) | BF_SDHC_ADSADDR_ADSADDR(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_VENDOR - Vendor Specific register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_VENDOR - Vendor Specific register (RW) * * Reset value: 0x00000001U * * This register contains the vendor-specific control/status register. */ typedef union _hw_sdhc_vendor { uint32_t U; struct _hw_sdhc_vendor_bitfields { uint32_t EXTDMAEN : 1; //!< [0] External DMA Request Enable uint32_t EXBLKNU : 1; //!< [1] Exact Block Number Block Read Enable //! For SDIO CMD53 uint32_t RESERVED0 : 14; //!< [15:2] uint32_t INTSTVAL : 8; //!< [23:16] Internal State Value uint32_t RESERVED1 : 8; //!< [31:24] } B; } hw_sdhc_vendor_t; #endif /*! * @name Constants and macros for entire SDHC_VENDOR register */ //@{ #define HW_SDHC_VENDOR_ADDR (REGS_SDHC_BASE + 0xC0U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_VENDOR (*(__IO hw_sdhc_vendor_t *) HW_SDHC_VENDOR_ADDR) #define HW_SDHC_VENDOR_RD() (HW_SDHC_VENDOR.U) #define HW_SDHC_VENDOR_WR(v) (HW_SDHC_VENDOR.U = (v)) #define HW_SDHC_VENDOR_SET(v) (HW_SDHC_VENDOR_WR(HW_SDHC_VENDOR_RD() | (v))) #define HW_SDHC_VENDOR_CLR(v) (HW_SDHC_VENDOR_WR(HW_SDHC_VENDOR_RD() & ~(v))) #define HW_SDHC_VENDOR_TOG(v) (HW_SDHC_VENDOR_WR(HW_SDHC_VENDOR_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_VENDOR bitfields */ /*! * @name Register SDHC_VENDOR, field EXTDMAEN[0] (RW) * * Enables the request to external DMA. When the internal DMA (either simple DMA * or advanced DMA) is not in use, and this bit is set, SDHC will send out DMA * request when the internal buffer is ready. This bit is particularly useful when * transferring data by CPU polling mode, and it is not allowed to send out the * external DMA request. By default, this bit is set. * * Values: * - 0 - In any scenario, SDHC does not send out the external DMA request. * - 1 - When internal DMA is not active, the external DMA request will be sent * out. */ //@{ #define BP_SDHC_VENDOR_EXTDMAEN (0U) //!< Bit position for SDHC_VENDOR_EXTDMAEN. #define BM_SDHC_VENDOR_EXTDMAEN (0x00000001U) //!< Bit mask for SDHC_VENDOR_EXTDMAEN. #define BS_SDHC_VENDOR_EXTDMAEN (1U) //!< Bit field size in bits for SDHC_VENDOR_EXTDMAEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_VENDOR_EXTDMAEN field. #define BR_SDHC_VENDOR_EXTDMAEN (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXTDMAEN)) #endif //! @brief Format value for bitfield SDHC_VENDOR_EXTDMAEN. #define BF_SDHC_VENDOR_EXTDMAEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_VENDOR_EXTDMAEN), uint32_t) & BM_SDHC_VENDOR_EXTDMAEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the EXTDMAEN field to a new value. #define BW_SDHC_VENDOR_EXTDMAEN(v) (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXTDMAEN) = (v)) #endif //@} /*! * @name Register SDHC_VENDOR, field EXBLKNU[1] (RW) * * This bit must be set before S/W issues CMD53 multi-block read with exact * block number. This bit must not be set if the CMD53 multi-block read is not exact * block number. * * Values: * - 0 - None exact block read. * - 1 - Exact block read for SDIO CMD53. */ //@{ #define BP_SDHC_VENDOR_EXBLKNU (1U) //!< Bit position for SDHC_VENDOR_EXBLKNU. #define BM_SDHC_VENDOR_EXBLKNU (0x00000002U) //!< Bit mask for SDHC_VENDOR_EXBLKNU. #define BS_SDHC_VENDOR_EXBLKNU (1U) //!< Bit field size in bits for SDHC_VENDOR_EXBLKNU. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_VENDOR_EXBLKNU field. #define BR_SDHC_VENDOR_EXBLKNU (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXBLKNU)) #endif //! @brief Format value for bitfield SDHC_VENDOR_EXBLKNU. #define BF_SDHC_VENDOR_EXBLKNU(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_VENDOR_EXBLKNU), uint32_t) & BM_SDHC_VENDOR_EXBLKNU) #ifndef __LANGUAGE_ASM__ //! @brief Set the EXBLKNU field to a new value. #define BW_SDHC_VENDOR_EXBLKNU(v) (BITBAND_ACCESS32(HW_SDHC_VENDOR_ADDR, BP_SDHC_VENDOR_EXBLKNU) = (v)) #endif //@} /*! * @name Register SDHC_VENDOR, field INTSTVAL[23:16] (RO) * * Internal state value, reflecting the corresponding state value selected by * Debug Select field. This field is read-only and write to this field does not * have effect. */ //@{ #define BP_SDHC_VENDOR_INTSTVAL (16U) //!< Bit position for SDHC_VENDOR_INTSTVAL. #define BM_SDHC_VENDOR_INTSTVAL (0x00FF0000U) //!< Bit mask for SDHC_VENDOR_INTSTVAL. #define BS_SDHC_VENDOR_INTSTVAL (8U) //!< Bit field size in bits for SDHC_VENDOR_INTSTVAL. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_VENDOR_INTSTVAL field. #define BR_SDHC_VENDOR_INTSTVAL (HW_SDHC_VENDOR.B.INTSTVAL) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_MMCBOOT - MMC Boot register //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_MMCBOOT - MMC Boot register (RW) * * Reset value: 0x00000000U * * This register contains the MMC fast boot control register. */ typedef union _hw_sdhc_mmcboot { uint32_t U; struct _hw_sdhc_mmcboot_bitfields { uint32_t DTOCVACK : 4; //!< [3:0] Boot ACK Time Out Counter Value uint32_t BOOTACK : 1; //!< [4] Boot Ack Mode Select uint32_t BOOTMODE : 1; //!< [5] Boot Mode Select uint32_t BOOTEN : 1; //!< [6] Boot Mode Enable uint32_t AUTOSABGEN : 1; //!< [7] uint32_t RESERVED0 : 8; //!< [15:8] uint32_t BOOTBLKCNT : 16; //!< [31:16] } B; } hw_sdhc_mmcboot_t; #endif /*! * @name Constants and macros for entire SDHC_MMCBOOT register */ //@{ #define HW_SDHC_MMCBOOT_ADDR (REGS_SDHC_BASE + 0xC4U) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_MMCBOOT (*(__IO hw_sdhc_mmcboot_t *) HW_SDHC_MMCBOOT_ADDR) #define HW_SDHC_MMCBOOT_RD() (HW_SDHC_MMCBOOT.U) #define HW_SDHC_MMCBOOT_WR(v) (HW_SDHC_MMCBOOT.U = (v)) #define HW_SDHC_MMCBOOT_SET(v) (HW_SDHC_MMCBOOT_WR(HW_SDHC_MMCBOOT_RD() | (v))) #define HW_SDHC_MMCBOOT_CLR(v) (HW_SDHC_MMCBOOT_WR(HW_SDHC_MMCBOOT_RD() & ~(v))) #define HW_SDHC_MMCBOOT_TOG(v) (HW_SDHC_MMCBOOT_WR(HW_SDHC_MMCBOOT_RD() ^ (v))) #endif //@} /* * Constants & macros for individual SDHC_MMCBOOT bitfields */ /*! * @name Register SDHC_MMCBOOT, field DTOCVACK[3:0] (RW) * * Values: * - 0000 - SDCLK x 2^8 * - 0001 - SDCLK x 2^9 * - 0010 - SDCLK x 2^10 * - 0011 - SDCLK x 2^11 * - 0100 - SDCLK x 2^12 * - 0101 - SDCLK x 2^13 * - 0110 - SDCLK x 2^14 * - 0111 - SDCLK x 2^15 * - 1110 - SDCLK x 2^22 * - 1111 - Reserved */ //@{ #define BP_SDHC_MMCBOOT_DTOCVACK (0U) //!< Bit position for SDHC_MMCBOOT_DTOCVACK. #define BM_SDHC_MMCBOOT_DTOCVACK (0x0000000FU) //!< Bit mask for SDHC_MMCBOOT_DTOCVACK. #define BS_SDHC_MMCBOOT_DTOCVACK (4U) //!< Bit field size in bits for SDHC_MMCBOOT_DTOCVACK. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_MMCBOOT_DTOCVACK field. #define BR_SDHC_MMCBOOT_DTOCVACK (HW_SDHC_MMCBOOT.B.DTOCVACK) #endif //! @brief Format value for bitfield SDHC_MMCBOOT_DTOCVACK. #define BF_SDHC_MMCBOOT_DTOCVACK(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_DTOCVACK), uint32_t) & BM_SDHC_MMCBOOT_DTOCVACK) #ifndef __LANGUAGE_ASM__ //! @brief Set the DTOCVACK field to a new value. #define BW_SDHC_MMCBOOT_DTOCVACK(v) (HW_SDHC_MMCBOOT_WR((HW_SDHC_MMCBOOT_RD() & ~BM_SDHC_MMCBOOT_DTOCVACK) | BF_SDHC_MMCBOOT_DTOCVACK(v))) #endif //@} /*! * @name Register SDHC_MMCBOOT, field BOOTACK[4] (RW) * * Values: * - 0 - No ack. * - 1 - Ack. */ //@{ #define BP_SDHC_MMCBOOT_BOOTACK (4U) //!< Bit position for SDHC_MMCBOOT_BOOTACK. #define BM_SDHC_MMCBOOT_BOOTACK (0x00000010U) //!< Bit mask for SDHC_MMCBOOT_BOOTACK. #define BS_SDHC_MMCBOOT_BOOTACK (1U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTACK. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_MMCBOOT_BOOTACK field. #define BR_SDHC_MMCBOOT_BOOTACK (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTACK)) #endif //! @brief Format value for bitfield SDHC_MMCBOOT_BOOTACK. #define BF_SDHC_MMCBOOT_BOOTACK(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTACK), uint32_t) & BM_SDHC_MMCBOOT_BOOTACK) #ifndef __LANGUAGE_ASM__ //! @brief Set the BOOTACK field to a new value. #define BW_SDHC_MMCBOOT_BOOTACK(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTACK) = (v)) #endif //@} /*! * @name Register SDHC_MMCBOOT, field BOOTMODE[5] (RW) * * Values: * - 0 - Normal boot. * - 1 - Alternative boot. */ //@{ #define BP_SDHC_MMCBOOT_BOOTMODE (5U) //!< Bit position for SDHC_MMCBOOT_BOOTMODE. #define BM_SDHC_MMCBOOT_BOOTMODE (0x00000020U) //!< Bit mask for SDHC_MMCBOOT_BOOTMODE. #define BS_SDHC_MMCBOOT_BOOTMODE (1U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTMODE. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_MMCBOOT_BOOTMODE field. #define BR_SDHC_MMCBOOT_BOOTMODE (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTMODE)) #endif //! @brief Format value for bitfield SDHC_MMCBOOT_BOOTMODE. #define BF_SDHC_MMCBOOT_BOOTMODE(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTMODE), uint32_t) & BM_SDHC_MMCBOOT_BOOTMODE) #ifndef __LANGUAGE_ASM__ //! @brief Set the BOOTMODE field to a new value. #define BW_SDHC_MMCBOOT_BOOTMODE(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTMODE) = (v)) #endif //@} /*! * @name Register SDHC_MMCBOOT, field BOOTEN[6] (RW) * * Values: * - 0 - Fast boot disable. * - 1 - Fast boot enable. */ //@{ #define BP_SDHC_MMCBOOT_BOOTEN (6U) //!< Bit position for SDHC_MMCBOOT_BOOTEN. #define BM_SDHC_MMCBOOT_BOOTEN (0x00000040U) //!< Bit mask for SDHC_MMCBOOT_BOOTEN. #define BS_SDHC_MMCBOOT_BOOTEN (1U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_MMCBOOT_BOOTEN field. #define BR_SDHC_MMCBOOT_BOOTEN (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTEN)) #endif //! @brief Format value for bitfield SDHC_MMCBOOT_BOOTEN. #define BF_SDHC_MMCBOOT_BOOTEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTEN), uint32_t) & BM_SDHC_MMCBOOT_BOOTEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the BOOTEN field to a new value. #define BW_SDHC_MMCBOOT_BOOTEN(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_BOOTEN) = (v)) #endif //@} /*! * @name Register SDHC_MMCBOOT, field AUTOSABGEN[7] (RW) * * When boot, enable auto stop at block gap function. This function will be * triggered, and host will stop at block gap when received card block cnt is equal * to BOOTBLKCNT. */ //@{ #define BP_SDHC_MMCBOOT_AUTOSABGEN (7U) //!< Bit position for SDHC_MMCBOOT_AUTOSABGEN. #define BM_SDHC_MMCBOOT_AUTOSABGEN (0x00000080U) //!< Bit mask for SDHC_MMCBOOT_AUTOSABGEN. #define BS_SDHC_MMCBOOT_AUTOSABGEN (1U) //!< Bit field size in bits for SDHC_MMCBOOT_AUTOSABGEN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_MMCBOOT_AUTOSABGEN field. #define BR_SDHC_MMCBOOT_AUTOSABGEN (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_AUTOSABGEN)) #endif //! @brief Format value for bitfield SDHC_MMCBOOT_AUTOSABGEN. #define BF_SDHC_MMCBOOT_AUTOSABGEN(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_AUTOSABGEN), uint32_t) & BM_SDHC_MMCBOOT_AUTOSABGEN) #ifndef __LANGUAGE_ASM__ //! @brief Set the AUTOSABGEN field to a new value. #define BW_SDHC_MMCBOOT_AUTOSABGEN(v) (BITBAND_ACCESS32(HW_SDHC_MMCBOOT_ADDR, BP_SDHC_MMCBOOT_AUTOSABGEN) = (v)) #endif //@} /*! * @name Register SDHC_MMCBOOT, field BOOTBLKCNT[31:16] (RW) * * Defines the stop at block gap value of automatic mode. When received card * block cnt is equal to BOOTBLKCNT and AUTOSABGEN is 1, then stop at block gap. */ //@{ #define BP_SDHC_MMCBOOT_BOOTBLKCNT (16U) //!< Bit position for SDHC_MMCBOOT_BOOTBLKCNT. #define BM_SDHC_MMCBOOT_BOOTBLKCNT (0xFFFF0000U) //!< Bit mask for SDHC_MMCBOOT_BOOTBLKCNT. #define BS_SDHC_MMCBOOT_BOOTBLKCNT (16U) //!< Bit field size in bits for SDHC_MMCBOOT_BOOTBLKCNT. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_MMCBOOT_BOOTBLKCNT field. #define BR_SDHC_MMCBOOT_BOOTBLKCNT (HW_SDHC_MMCBOOT.B.BOOTBLKCNT) #endif //! @brief Format value for bitfield SDHC_MMCBOOT_BOOTBLKCNT. #define BF_SDHC_MMCBOOT_BOOTBLKCNT(v) (__REG_VALUE_TYPE((__REG_VALUE_TYPE((v), uint32_t) << BP_SDHC_MMCBOOT_BOOTBLKCNT), uint32_t) & BM_SDHC_MMCBOOT_BOOTBLKCNT) #ifndef __LANGUAGE_ASM__ //! @brief Set the BOOTBLKCNT field to a new value. #define BW_SDHC_MMCBOOT_BOOTBLKCNT(v) (HW_SDHC_MMCBOOT_WR((HW_SDHC_MMCBOOT_RD() & ~BM_SDHC_MMCBOOT_BOOTBLKCNT) | BF_SDHC_MMCBOOT_BOOTBLKCNT(v))) #endif //@} //------------------------------------------------------------------------------------------- // HW_SDHC_HOSTVER - Host Controller Version //------------------------------------------------------------------------------------------- #ifndef __LANGUAGE_ASM__ /*! * @brief HW_SDHC_HOSTVER - Host Controller Version (RO) * * Reset value: 0x00001201U * * This register contains the vendor host controller version information. All * bits are read only and will read the same as the power-reset value. */ typedef union _hw_sdhc_hostver { uint32_t U; struct _hw_sdhc_hostver_bitfields { uint32_t SVN : 8; //!< [7:0] Specification Version Number uint32_t VVN : 8; //!< [15:8] Vendor Version Number uint32_t RESERVED0 : 16; //!< [31:16] } B; } hw_sdhc_hostver_t; #endif /*! * @name Constants and macros for entire SDHC_HOSTVER register */ //@{ #define HW_SDHC_HOSTVER_ADDR (REGS_SDHC_BASE + 0xFCU) #ifndef __LANGUAGE_ASM__ #define HW_SDHC_HOSTVER (*(__I hw_sdhc_hostver_t *) HW_SDHC_HOSTVER_ADDR) #define HW_SDHC_HOSTVER_RD() (HW_SDHC_HOSTVER.U) #endif //@} /* * Constants & macros for individual SDHC_HOSTVER bitfields */ /*! * @name Register SDHC_HOSTVER, field SVN[7:0] (RO) * * These status bits indicate the host controller specification version. * * Values: * - 1 - SD host specification version 2.0, supports test event register and * ADMA. */ //@{ #define BP_SDHC_HOSTVER_SVN (0U) //!< Bit position for SDHC_HOSTVER_SVN. #define BM_SDHC_HOSTVER_SVN (0x000000FFU) //!< Bit mask for SDHC_HOSTVER_SVN. #define BS_SDHC_HOSTVER_SVN (8U) //!< Bit field size in bits for SDHC_HOSTVER_SVN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HOSTVER_SVN field. #define BR_SDHC_HOSTVER_SVN (HW_SDHC_HOSTVER.B.SVN) #endif //@} /*! * @name Register SDHC_HOSTVER, field VVN[15:8] (RO) * * These status bits are reserved for the vendor version number. The host driver * shall not use this status. * * Values: * - 0 - Freescale SDHC version 1.0 * - 10000 - Freescale SDHC version 2.0 * - 10001 - Freescale SDHC version 2.1 * - 10010 - Freescale SDHC version 2.2 */ //@{ #define BP_SDHC_HOSTVER_VVN (8U) //!< Bit position for SDHC_HOSTVER_VVN. #define BM_SDHC_HOSTVER_VVN (0x0000FF00U) //!< Bit mask for SDHC_HOSTVER_VVN. #define BS_SDHC_HOSTVER_VVN (8U) //!< Bit field size in bits for SDHC_HOSTVER_VVN. #ifndef __LANGUAGE_ASM__ //! @brief Read current value of the SDHC_HOSTVER_VVN field. #define BR_SDHC_HOSTVER_VVN (HW_SDHC_HOSTVER.B.VVN) #endif //@} //------------------------------------------------------------------------------------------- // hw_sdhc_t - module struct //------------------------------------------------------------------------------------------- /*! * @brief All SDHC module registers. */ #ifndef __LANGUAGE_ASM__ #pragma pack(1) typedef struct _hw_sdhc { __IO hw_sdhc_dsaddr_t DSADDR; //!< [0x0] DMA System Address register __IO hw_sdhc_blkattr_t BLKATTR; //!< [0x4] Block Attributes register __IO hw_sdhc_cmdarg_t CMDARG; //!< [0x8] Command Argument register __IO hw_sdhc_xfertyp_t XFERTYP; //!< [0xC] Transfer Type register __I hw_sdhc_cmdrsp0_t CMDRSP0; //!< [0x10] Command Response 0 __I hw_sdhc_cmdrsp1_t CMDRSP1; //!< [0x14] Command Response 1 __I hw_sdhc_cmdrsp2_t CMDRSP2; //!< [0x18] Command Response 2 __I hw_sdhc_cmdrsp3_t CMDRSP3; //!< [0x1C] Command Response 3 __IO hw_sdhc_datport_t DATPORT; //!< [0x20] Buffer Data Port register __I hw_sdhc_prsstat_t PRSSTAT; //!< [0x24] Present State register __IO hw_sdhc_proctl_t PROCTL; //!< [0x28] Protocol Control register __IO hw_sdhc_sysctl_t SYSCTL; //!< [0x2C] System Control register __IO hw_sdhc_irqstat_t IRQSTAT; //!< [0x30] Interrupt Status register __IO hw_sdhc_irqstaten_t IRQSTATEN; //!< [0x34] Interrupt Status Enable register __IO hw_sdhc_irqsigen_t IRQSIGEN; //!< [0x38] Interrupt Signal Enable register __I hw_sdhc_ac12err_t AC12ERR; //!< [0x3C] Auto CMD12 Error Status Register __I hw_sdhc_htcapblt_t HTCAPBLT; //!< [0x40] Host Controller Capabilities __IO hw_sdhc_wml_t WML; //!< [0x44] Watermark Level Register uint8_t _reserved0[8]; __O hw_sdhc_fevt_t FEVT; //!< [0x50] Force Event register __I hw_sdhc_admaes_t ADMAES; //!< [0x54] ADMA Error Status register __IO hw_sdhc_adsaddr_t ADSADDR; //!< [0x58] ADMA System Addressregister uint8_t _reserved1[100]; __IO hw_sdhc_vendor_t VENDOR; //!< [0xC0] Vendor Specific register __IO hw_sdhc_mmcboot_t MMCBOOT; //!< [0xC4] MMC Boot register uint8_t _reserved2[52]; __I hw_sdhc_hostver_t HOSTVER; //!< [0xFC] Host Controller Version } hw_sdhc_t; #pragma pack() //! @brief Macro to access all SDHC registers. //! @return Reference (not a pointer) to the registers struct. To get a pointer to the struct, //! use the '&' operator, like <code>&HW_SDHC</code>. #define HW_SDHC (*(hw_sdhc_t *) REGS_SDHC_BASE) #endif #endif // __HW_SDHC_REGISTERS_H__ // v22/130726/0.9 // EOF