shao ziyang
mbed library sources
Dependents: frdm_kl05z_gpio_test
Fork of
mbed-src
by 
mbed official
Diff: targets/cmsis/TARGET_STM/TARGET_DISCO_F407VG/system_stm32f4xx.c
- Revision:
- 133:d4dda5c437f0
- Child:
- 242:7074e42da0b2
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_DISCO_F407VG/system_stm32f4xx.c Mon Mar 24 17:45:07 2014 +0000
@@ -0,0 +1,343 @@
+/**
+ ******************************************************************************
+ * @file system_stm32f4xx.c
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 18-February-2014
+ * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
+ *
+ * This file provides two functions and one global variable to be called from
+ * user application:
+ * - SystemInit(): This function is called at startup just after reset and
+ * before branch to main program. This call is made inside
+ * the "startup_stm32f4xx.s" file.
+ *
+ * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
+ * by the user application to setup the SysTick
+ * timer or configure other parameters.
+ *
+ * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
+ * be called whenever the core clock is changed
+ * during program execution.
+ *
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/** @addtogroup CMSIS
+ * @{
+ */
+
+/** @addtogroup stm32f4xx_system
+ * @{
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Includes
+ * @{
+ */
+
+#include "stm32f4xx_hal.h"
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Defines
+ * @{
+ */
+
+/************************* Miscellaneous Configuration ************************/
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+/******************************************************************************/
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Variables
+ * @{
+ */
+ /* This variable is updated in three ways:
+ 1) by calling CMSIS function SystemCoreClockUpdate()
+ 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
+ 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
+ Note: If you use this function to configure the system clock; then there
+ is no need to call the 2 first functions listed above, since SystemCoreClock
+ variable is updated automatically.
+ */
+ uint32_t SystemCoreClock = 168000000; /* [CHANGED FOR MBED] */
+ __I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
+ * @{
+ */
+
+/* [ADDED FOR MBED] */
+void SystemClock_Config(void);
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the FPU setting, vector table location and External memory
+ * configuration.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+ #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+ #endif
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+ /* [ADDED FOR MBED] */
+ HAL_Init();
+ SystemClock_Config();
+}
+
+/**
+ * @brief Update SystemCoreClock variable according to Clock Register Values.
+ * The SystemCoreClock variable contains the core clock (HCLK), it can
+ * be used by the user application to setup the SysTick timer or configure
+ * other parameters.
+ *
+ * @note Each time the core clock (HCLK) changes, this function must be called
+ * to update SystemCoreClock variable value. Otherwise, any configuration
+ * based on this variable will be incorrect.
+ *
+ * @note - The system frequency computed by this function is not the real
+ * frequency in the chip. It is calculated based on the predefined
+ * constant and the selected clock source:
+ *
+ * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
+ *
+ * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
+ *
+ * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
+ * or HSI_VALUE(*) multiplied/divided by the PLL factors.
+ *
+ * (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
+ * 16 MHz) but the real value may vary depending on the variations
+ * in voltage and temperature.
+ *
+ * (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (its value
+ * depends on the application requirements), user has to ensure that HSE_VALUE
+ * is same as the real frequency of the crystal used. Otherwise, this function
+ * may have wrong result.
+ *
+ * - The result of this function could be not correct when using fractional
+ * value for HSE crystal.
+ *
+ * @param None
+ * @retval None
+ */
+void SystemCoreClockUpdate(void)
+{
+ uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
+
+ /* Get SYSCLK source -------------------------------------------------------*/
+ tmp = RCC->CFGR & RCC_CFGR_SWS;
+
+ switch (tmp)
+ {
+ case 0x00: /* HSI used as system clock source */
+ SystemCoreClock = HSI_VALUE;
+ break;
+ case 0x04: /* HSE used as system clock source */
+ SystemCoreClock = HSE_VALUE;
+ break;
+ case 0x08: /* PLL used as system clock source */
+
+ /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
+ SYSCLK = PLL_VCO / PLL_P
+ */
+ pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
+ pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
+
+ if (pllsource != 0)
+ {
+ /* HSE used as PLL clock source */
+ pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+ }
+ else
+ {
+ /* HSI used as PLL clock source */
+ pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+ }
+
+ pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
+ SystemCoreClock = pllvco/pllp;
+ break;
+ default:
+ SystemCoreClock = HSI_VALUE;
+ break;
+ }
+ /* Compute HCLK frequency --------------------------------------------------*/
+ /* Get HCLK prescaler */
+ tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
+ /* HCLK frequency */
+ SystemCoreClock >>= tmp;
+}
+
+/* [ADDED FOR MBED]
+ Configure the System clock to 84 MHz (max value) using the internal HSI 16 MHz clock */
+void SystemClock_Config(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __PWR_CLK_ENABLE();
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
+
+ /* Enable HSI Oscillator and activate PLL with HSI as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
+ RCC_OscInitStruct.LSEState = RCC_LSE_OFF;
+ RCC_OscInitStruct.LSIState = RCC_LSI_OFF;
+ RCC_OscInitStruct.HSICalibrationValue = 16;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 8;
+ RCC_OscInitStruct.PLL.PLLN = 336;
+ RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+ {
+ // System clock initialization failed
+ while(1)
+ {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+
+ /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz (SPI1 clock...)
+ if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
+ {
+ // System clock initialization failed
+ while(1)
+ {
+ // [TODO] Put something here to tell the user that a problem occured...
+ }
+ }
+
+ /* Update the SystemCoreClock variable
+ - Not needed because the variable is already set on top of this file.
+ - Warning: this function call is removed by the compiler with -O3/-Otime options. */
+ //SystemCoreClockUpdate();
+
+ /* Output SYSCLK on MCO2 pin(PC9) for debugging purpose */
+ //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); // 168 MHz / 4 = 42 MHz
+}
+
+/* [ADDED FOR MBED]
+ Used for the different timeouts in the HAL */
+void SysTick_Handler(void)
+{
+ HAL_IncTick();
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/