Ricardo Benitez
meh
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F401RE/stm32f4xx_hal_rcc_ex.h
- Revision:
- 110:165afa46840b
- Parent:
- 106:ba1f97679dad
--- a/TARGET_NUCLEO_F401RE/stm32f4xx_hal_rcc_ex.h Thu Oct 29 08:40:18 2015 +0000
+++ b/TARGET_NUCLEO_F401RE/stm32f4xx_hal_rcc_ex.h Wed Nov 25 13:21:40 2015 +0000
@@ -2,8 +2,8 @@
******************************************************************************
* @file stm32f4xx_hal_rcc_ex.h
* @author MCD Application Team
- * @version V1.3.2
- * @date 26-June-2015
+ * @version V1.4.1
+ * @date 09-October-2015
* @brief Header file of RCC HAL Extension module.
******************************************************************************
* @attention
@@ -68,10 +68,10 @@
This parameter can be a value of @ref RCC_PLL_Config */
uint32_t PLLSource; /*!< RCC_PLLSource: PLL entry clock source.
- This parameter must be a value of @ref RCC_PLL_Clock_Source */
+ This parameter must be a value of @ref RCC_PLL_Clock_Source */
uint32_t PLLM; /*!< PLLM: Division factor for PLL VCO input clock.
- This parameter must be a number between Min_Data = 0 and Max_Data = 63 */
+ This parameter must be a number between Min_Data = 0 and Max_Data = 63 */
uint32_t PLLN; /*!< PLLN: Multiplication factor for PLL VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
@@ -81,11 +81,13 @@
uint32_t PLLQ; /*!< PLLQ: Division factor for OTG FS, SDIO and RNG clocks.
This parameter must be a number between Min_Data = 4 and Max_Data = 15 */
-#if defined(STM32F446xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) || defined(STM32F469xx) ||\
+ defined(STM32F479xx)
uint32_t PLLR; /*!< PLLR: PLL division factor for I2S, SAI, SYSTEM, SPDIFRX clocks.
- This parameter is only available in STM32F446xx devices.
+ This parameter is only available in STM32F410xx/STM32F446xx/STM32F469xx and STM32F479xx
+ devices.
This parameter must be a number between Min_Data = 2 and Max_Data = 7 */
-#endif /* STM32F446xx */
+#endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx */
}RCC_PLLInitTypeDef;
#if defined(STM32F446xx)
@@ -95,7 +97,7 @@
typedef struct
{
uint32_t PLLI2SM; /*!< Specifies division factor for PLL VCO input clock.
- This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
+ This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
@@ -105,7 +107,7 @@
uint32_t PLLI2SQ; /*!< Specifies the division factor for SAI clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 15.
- This parameter will be used only when PLLI2S is selected as Clock Source SAI */
+ This parameter will be used only when PLLI2S is selected as Clock Source SAI */
uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 7.
@@ -118,10 +120,10 @@
typedef struct
{
uint32_t PLLSAIM; /*!< Spcifies division factor for PLL VCO input clock.
- This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
+ This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
uint32_t PLLSAIN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
- This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
+ This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
uint32_t PLLSAIP; /*!< Specifies division factor for OTG FS, SDIO and RNG clocks.
This parameter must be a value of @ref RCCEx_PLLSAIP_Clock_Divider */
@@ -187,7 +189,32 @@
}RCC_PeriphCLKInitTypeDef;
#endif /* STM32F446xx */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/**
+ * @brief RCC extended clocks structure definition
+ */
+typedef struct
+{
+ uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured.
+ This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */
+
+ uint32_t I2SClockSelection; /*!< Specifies RTC Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_I2S_APB_Clock_Source */
+
+ uint32_t RTCClockSelection; /*!< Specifies RTC Clock Source Selection.
+ This parameter can be a value of @ref RCC_RTC_Clock_Source */
+
+ uint32_t Lptim1ClockSelection; /*!< Specifies LPTIM1 Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_LPTIM1_Clock_Source */
+
+ uint32_t Fmpi2c1ClockSelection; /*!< Specifies FMPI2C1 Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_FMPI2C1_Clock_Source */
+ uint8_t TIMPresSelection; /*!< Specifies TIM Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */
+}RCC_PeriphCLKInitTypeDef;
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/**
* @brief PLLI2S Clock structure definition
@@ -215,6 +242,11 @@
uint32_t PLLSAIN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432.
This parameter will be used only when PLLSAI is selected as Clock Source SAI or LTDC */
+#if defined(STM32F469xx) || defined(STM32F479xx)
+ uint32_t PLLSAIP; /*!< Specifies division factor for OTG FS and SDIO clocks.
+ This parameter is only available in STM32F469xx/STM32F479xx devices.
+ This parameter must be a value of @ref RCCEx_PLLSAIP_Clock_Divider */
+#endif /* STM32F469xx || STM32F479xx */
uint32_t PLLSAIQ; /*!< Specifies the division factor for SAI1 clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 15.
@@ -255,18 +287,24 @@
uint8_t TIMPresSelection; /*!< Specifies TIM Clock Prescalers Selection.
This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */
-
+#if defined(STM32F469xx) || defined(STM32F479xx)
+ uint32_t Clk48ClockSelection; /*!< Specifies CK48 Clock Selection this clock used OTG FS, SDIO and RNG clocks.
+ This parameter can be a value of @ref RCCEx_CK48_Clock_Source */
+
+ uint32_t SdioClockSelection; /*!< Specifies SDIO Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_SDIO_Clock_Source */
+#endif /* STM32F469xx || STM32F479xx */
}RCC_PeriphCLKInitTypeDef;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
/**
* @brief PLLI2S Clock structure definition
*/
typedef struct
{
-#if defined(STM32F411xE)
+#if defined(STM32F411xE)
uint32_t PLLI2SM; /*!< PLLM: Division factor for PLLI2S VCO input clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 62 */
#endif /* STM32F411xE */
@@ -294,7 +332,7 @@
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
uint32_t RTCClockSelection; /*!< Specifies RTC Clock Prescalers Selection.
- This parameter can be a value of @ref RCC_RTC_Clock_Source */
+ This parameter can be a value of @ref RCC_RTC_Clock_Source */
}RCC_PeriphCLKInitTypeDef;
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
@@ -310,7 +348,17 @@
/** @defgroup RCCEx_Periph_Clock_Selection RCC Periph Clock Selection
* @{
*/
-/*------------------------------- Peripheral Clock source for STM32F446xx -----------------------------*/
+/*------------------- Peripheral Clock source for STM32F410xx ----------------*/
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
+#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000002)
+#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000004)
+#define RCC_PERIPHCLK_FMPI2C1 ((uint32_t)0x00000008)
+#define RCC_PERIPHCLK_LPTIM1 ((uint32_t)0x00000010)
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------- Peripheral Clock source for STM32F446xx ----------------*/
#if defined(STM32F446xx)
#define RCC_PERIPHCLK_I2S_APB1 ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_I2S_APB2 ((uint32_t)0x00000002)
@@ -325,9 +373,23 @@
#define RCC_PERIPHCLK_SPDIFRX ((uint32_t)0x00000400)
#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000800)
#endif /* STM32F446xx */
-/*-----------------------------------------------------------------------------------------------------*/
-
-/*--------------- Peripheral Clock source for STM32F42xxx/STM32F43xxx ---------------------*/
+/*-----------------------------------------------------------------------------*/
+
+/*----------- Peripheral Clock source for STM32F469xx/STM32F479xx -------------*/
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
+#define RCC_PERIPHCLK_SAI_PLLI2S ((uint32_t)0x00000002)
+#define RCC_PERIPHCLK_SAI_PLLSAI ((uint32_t)0x00000004)
+#define RCC_PERIPHCLK_LTDC ((uint32_t)0x00000008)
+#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000010)
+#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020)
+#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000040)
+#define RCC_PERIPHCLK_CK48 ((uint32_t)0x00000080)
+#define RCC_PERIPHCLK_SDIO ((uint32_t)0x00000100)
+#endif /* STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*-------- Peripheral Clock source for STM32F42xxx/STM32F43xxx ---------------*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_SAI_PLLI2S ((uint32_t)0x00000002)
@@ -337,29 +399,44 @@
#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020)
#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000040)
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-/*-----------------------------------------------------------------------------------------------------*/
-
-/*------------------------ Peripheral Clock source for STM32F40xxx/STM32F41xxx ------------------------*/
+/*----------------------------------------------------------------------------*/
+
+/*-------- Peripheral Clock source for STM32F40xxx/STM32F41xxx ---------------*/
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000002)
#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000004)
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
-/*-----------------------------------------------------------------------------------------------------*/
+/*----------------------------------------------------------------------------*/
/**
* @}
*/
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_I2S_Clock_Source I2S Clock Source
+ * @{
+ */
+#define RCC_I2SCLKSOURCE_PLLI2S ((uint32_t)0x00000000)
+#define RCC_I2SCLKSOURCE_EXT ((uint32_t)0x00000001)
+/**
+ * @}
+ */
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
/** @defgroup RCCEx_PLLSAI_DIVR RCC PLLSAI DIVR
* @{
*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
#define RCC_PLLSAIDIVR_2 ((uint32_t)0x00000000)
#define RCC_PLLSAIDIVR_4 ((uint32_t)0x00010000)
#define RCC_PLLSAIDIVR_8 ((uint32_t)0x00020000)
#define RCC_PLLSAIDIVR_16 ((uint32_t)0x00030000)
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
/**
* @}
*/
@@ -367,12 +444,12 @@
/** @defgroup RCCEx_PLLI2SP_Clock_Divider RCC PLLI2SP Clock Divider
* @{
*/
-#if defined(STM32F446xx)
+#if defined(STM32F446xx)
#define RCC_PLLI2SP_DIV2 ((uint32_t)0x00000002)
#define RCC_PLLI2SP_DIV4 ((uint32_t)0x00000004)
#define RCC_PLLI2SP_DIV6 ((uint32_t)0x00000006)
#define RCC_PLLI2SP_DIV8 ((uint32_t)0x00000008)
-#endif /* STM32F446xx */
+#endif /* STM32F446xx */
/**
* @}
*/
@@ -380,17 +457,17 @@
/** @defgroup RCCEx_PLLSAIP_Clock_Divider RCC PLLSAIP Clock Divider
* @{
*/
-#if defined(STM32F446xx)
+#if defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define RCC_PLLSAIP_DIV2 ((uint32_t)0x00000002)
#define RCC_PLLSAIP_DIV4 ((uint32_t)0x00000004)
#define RCC_PLLSAIP_DIV6 ((uint32_t)0x00000006)
#define RCC_PLLSAIP_DIV8 ((uint32_t)0x00000008)
-#endif /* STM32F446xx */
+#endif /* STM32F446xx || STM32F469xx || STM32F479xx */
/**
* @}
*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @defgroup RCCEx_SAI_BlockA_Clock_Source RCC SAI BlockA Clock Source
* @{
*/
@@ -410,7 +487,36 @@
/**
* @}
*/
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_CK48_Clock_Source RCC CK48 Clock Source
+ * @{
+ */
+#define RCC_CK48CLKSOURCE_PLLQ ((uint32_t)0x00000000)
+#define RCC_CK48CLKSOURCE_PLLSAIP ((uint32_t)RCC_DCKCFGR_CK48MSEL)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_SDIO_Clock_Source RCC SDIO Clock Source
+ * @{
+ */
+#define RCC_SDIOCLKSOURCE_CK48 ((uint32_t)0x00000000)
+#define RCC_SDIOCLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR_SDIOSEL)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_DSI_Clock_Source RCC DSI Clock Source
+ * @{
+ */
+#define RCC_DSICLKSOURCE_DSIPHY ((uint32_t)0x00000000)
+#define RCC_DSICLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_DSISEL)
+/**
+ * @}
+ */
+#endif /* STM32F469xx || STM32F479xx */
#if defined(STM32F446xx)
/** @defgroup RCCEx_SAI1_Clock_Source RCC SAI1 Clock Source
@@ -502,11 +608,42 @@
/**
* @}
*/
-
+
#endif /* STM32F446xx */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\
- defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+
+/** @defgroup RCCEx_I2S_APB_Clock_Source RCC I2S APB Clock Source
+ * @{
+ */
+#define RCC_I2SAPBCLKSOURCE_PLLR ((uint32_t)0x00000000)
+#define RCC_I2SAPBCLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_I2SSRC_0)
+#define RCC_I2SAPBCLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_I2SSRC_1)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_FMPI2C1_Clock_Source RCC FMPI2C1 Clock Source
+ * @{
+ */
+#define RCC_FMPI2C1CLKSOURCE_APB ((uint32_t)0x00000000)
+#define RCC_FMPI2C1CLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_0)
+#define RCC_FMPI2C1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_1)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_LPTIM1_Clock_Source RCC LPTIM1 Clock Source
+ * @{
+ */
+#define RCC_LPTIM1CLKSOURCE_PCLK ((uint32_t)0x00000000)
+#define RCC_LPTIM1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_0)
+#define RCC_LPTIM1CLKSOURCE_LSI ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_1)
+#define RCC_LPTIM1CLKSOURCE_LSE ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_0 | RCC_DCKCFGR2_LPTIM1SEL_1)
+/**
+ * @}
+ */
+
/** @defgroup RCCEx_TIM_PRescaler_Selection RCC TIM PRescaler Selection
* @{
*/
@@ -515,9 +652,24 @@
/**
* @}
*/
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx */
-
-#if defined(STM32F411xE) || defined(STM32F446xx)
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_TIM_PRescaler_Selection RCC TIM PRescaler Selection
+ * @{
+ */
+#define RCC_TIMPRES_DESACTIVATED ((uint8_t)0x00)
+#define RCC_TIMPRES_ACTIVATED ((uint8_t)0x01)
+/**
+ * @}
+ */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE ||\
+ STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @defgroup RCCEx_LSE_Dual_Mode_Selection RCC LSE Dual Mode Selection
* @{
*/
@@ -526,7 +678,38 @@
/**
* @}
*/
-#endif /* STM32F411xE || STM32F446xx */
+#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCC_MCO2_Clock_Source MCO2 Clock Source
+ * @{
+ */
+#define RCC_MCO2SOURCE_SYSCLK ((uint32_t)0x00000000)
+#define RCC_MCO2SOURCE_PLLI2SCLK RCC_CFGR_MCO2_0
+#define RCC_MCO2SOURCE_HSE RCC_CFGR_MCO2_1
+#define RCC_MCO2SOURCE_PLLCLK RCC_CFGR_MCO2
+/**
+ * @}
+ */
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @defgroup RCC_MCO2_Clock_Source MCO2 Clock Source
+ * @{
+ */
+#define RCC_MCO2SOURCE_SYSCLK ((uint32_t)0x00000000)
+#define RCC_MCO2SOURCE_I2SCLK RCC_CFGR_MCO2_0
+#define RCC_MCO2SOURCE_HSE RCC_CFGR_MCO2_1
+#define RCC_MCO2SOURCE_PLLCLK RCC_CFGR_MCO2
+/**
+ * @}
+ */
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
/**
* @}
@@ -536,13 +719,49 @@
/** @defgroup RCCEx_Exported_Macros RCCEx Exported Macros
* @{
*/
-/*------------------------------- STM32F42xxx/STM32F43xxx ----------------------------------*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
-/** @brief Enables or disables the AHB1 peripheral clock.
+/*------------------- STM32F42xxx/STM32F43xxx/STM32F469xx/STM32F479xx --------*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_GPIOI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\
@@ -627,7 +846,8 @@
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __HAL_RCC_GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN))
@@ -640,6 +860,9 @@
#define __HAL_RCC_ETHMACPTP_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACPTPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
/**
* @brief Enable ETHERNET clock.
@@ -657,14 +880,17 @@
__HAL_RCC_ETHMACRX_CLK_DISABLE(); \
__HAL_RCC_ETHMAC_CLK_DISABLE(); \
} while(0)
-
-/** @brief Enable or disable the AHB2 peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
-
-#define __HAL_RCC_DCMI_CLK_ENABLE() do { \
+ #define __HAL_RCC_DCMI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\
/* Delay after an RCC peripheral clock enabling */ \
@@ -673,7 +899,7 @@
} while(0)
#define __HAL_RCC_DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN))
-#if defined(STM32F437xx)|| defined(STM32F439xx)
+#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx)
#define __HAL_RCC_CRYP_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_CRYPEN);\
@@ -691,9 +917,40 @@
#define __HAL_RCC_CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN))
#define __HAL_RCC_HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN))
-#endif /* STM32F437xx || STM32F439xx */
-
-/** @brief Enables or disables the AHB3 peripheral clock.
+#endif /* STM32F437xx || STM32F439xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEX_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -706,8 +963,22 @@
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_FMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FMCEN))
-
-/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_QSPI_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -810,7 +1081,46 @@
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART8EN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
@@ -824,8 +1134,12 @@
#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
#define __HAL_RCC_UART7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART7EN))
#define __HAL_RCC_UART8_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART8EN))
-
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -872,22 +1186,69 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN);\
UNUSED(tmpreg); \
} while(0)
-
-#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
-#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
-#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
-#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
-#define __HAL_RCC_SPI6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI6EN))
-#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
-
-#if defined(STM32F429xx)|| defined(STM32F439xx)
-#define __HAL_RCC_LTDC_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_LTDCEN))
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
+#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
+#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
+#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
+#define __HAL_RCC_SPI6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI6EN))
+#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
+
+#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_LTDC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_LTDCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_LTDCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_LTDC_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_LTDCEN))
-#endif /* STM32F429xx || STM32F439xx */
-
-/** @brief Force or release AHB1 peripheral reset.
- */
+#endif /* STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_DSI_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_DSIEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DSIEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_DSI_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_DSIEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST))
@@ -896,7 +1257,10 @@
#define __HAL_RCC_GPIOJ_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOJRST))
#define __HAL_RCC_GPIOK_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOKRST))
#define __HAL_RCC_DMA2D_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA2DRST))
-
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST))
@@ -905,26 +1269,55 @@
#define __HAL_RCC_GPIOJ_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOJRST))
#define __HAL_RCC_GPIOK_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOKRST))
#define __HAL_RCC_DMA2D_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA2DRST))
-
-/** @brief Force or release AHB2 peripheral reset.
- */
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
-#if defined(STM32F437xx)|| defined(STM32F439xx)
+#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx)
#define __HAL_RCC_CRYP_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_CRYPRST))
#define __HAL_RCC_HASH_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_HASHRST))
#define __HAL_RCC_CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST))
#define __HAL_RCC_HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST))
-#endif /* STM32F437xx || STM32F439xx */
-
-/** @brief Force or release AHB3 peripheral reset
+#endif /* STM32F437xx || STM32F439xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
*/
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
#define __HAL_RCC_FMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FMCRST))
#define __HAL_RCC_FMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FMCRST))
-
-/** @brief Force or release APB1 peripheral reset.
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST))
+#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
*/
#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
@@ -939,7 +1332,17 @@
#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
#define __HAL_RCC_UART7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART7RST))
#define __HAL_RCC_UART8_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART8RST))
-
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
@@ -953,30 +1356,51 @@
#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
#define __HAL_RCC_UART7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART7RST))
#define __HAL_RCC_UART8_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART8RST))
-
-/** @brief Force or release APB2 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
*/
#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
#define __HAL_RCC_SPI6_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI6RST))
#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST))
-
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET()(RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
#define __HAL_RCC_SPI6_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI6RST))
#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST))
-#if defined(STM32F429xx)|| defined(STM32F439xx)
+#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define __HAL_RCC_LTDC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_LTDCRST))
#define __HAL_RCC_LTDC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_LTDCRST))
-#endif /* STM32F429xx|| STM32F439xx */
-
-/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+#endif /* STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_DSI_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_DSIRST))
+#define __HAL_RCC_DSI_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_DSIRST))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN))
@@ -991,7 +1415,13 @@
#define __HAL_RCC_GPIOK_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOKLPEN))
#define __HAL_RCC_SRAM3_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM3LPEN))
#define __HAL_RCC_DMA2D_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA2DLPEN))
-
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN))
@@ -1005,25 +1435,44 @@
#define __HAL_RCC_GPIOJ_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOJLPEN))
#define __HAL_RCC_GPIOK_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOKLPEN))
#define __HAL_RCC_DMA2D_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA2DLPEN))
-
-/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
- * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN))
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN))
+
#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
-#if defined(STM32F437xx)|| defined(STM32F439xx)
+#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx)
#define __HAL_RCC_CRYP_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_CRYPLPEN))
#define __HAL_RCC_HASH_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_HASHLPEN))
#define __HAL_RCC_CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN))
#define __HAL_RCC_HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN))
-#endif /* STM32F437xx || STM32F439xx */
-
-/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
+#endif /* STM32F437xx || STM32F439xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1032,7 +1481,16 @@
#define __HAL_RCC_FMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FMCLPEN))
#define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FMCLPEN))
-/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_QSPILPEN))
+#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1051,7 +1509,17 @@
#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
#define __HAL_RCC_UART7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART7LPEN))
#define __HAL_RCC_UART8_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART8LPEN))
-
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
@@ -1065,8 +1533,12 @@
#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
#define __HAL_RCC_UART7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART7LPEN))
#define __HAL_RCC_UART8_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART8LPEN))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1078,7 +1550,13 @@
#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
#define __HAL_RCC_SPI6_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI6LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI1LPEN))
-
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
@@ -1086,22 +1564,65 @@
#define __HAL_RCC_SPI6_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI6LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI1LPEN))
-#if defined(STM32F429xx)|| defined(STM32F439xx)
+#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define __HAL_RCC_LTDC_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_LTDCLPEN))
#define __HAL_RCC_LTDC_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_LTDCLPEN))
-#endif /* STM32F429xx || STM32F439xx */
-
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx */
-/*---------------------------------------------------------------------------------------------*/
-
-/*----------------------------------- STM32F40xxx/STM32F41xxx----------------------------------*/
+#endif /* STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_DSI_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_DSILPEN))
+#define __HAL_RCC_DSI_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_DSILPEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*----------------------------------- STM32F40xxx/STM32F41xxx-----------------*/
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)
-/** @brief Enables or disables the AHB1 peripheral clock.
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_GPIOI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\
@@ -1137,13 +1658,16 @@
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __HAL_RCC_GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN))
#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
-
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
#if defined(STM32F407xx)|| defined(STM32F417xx)
/**
* @brief Enable ETHERNET clock.
@@ -1195,12 +1719,33 @@
__HAL_RCC_ETHMAC_CLK_DISABLE(); \
} while(0)
#endif /* STM32F407xx || STM32F417xx */
-
-/** @brief Enable or disable the AHB2 peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN))
+
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __HAL_RCC_DCMI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
@@ -1230,8 +1775,12 @@
#define __HAL_RCC_CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN))
#define __HAL_RCC_HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN))
#endif /* STM32F415xx || STM32F417xx */
-
-/** @brief Enables or disables the AHB3 peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1244,8 +1793,12 @@
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_FSMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FSMCEN))
-
-/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1327,7 +1880,46 @@
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
@@ -1339,8 +1931,12 @@
#define __HAL_RCC_CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN))
#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN))
#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
-
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1366,27 +1962,68 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\
UNUSED(tmpreg); \
} while(0)
-
-#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
-#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
-#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
-
-/** @brief Force or release AHB1 peripheral reset.
- */
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
+#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
+#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST))
#define __HAL_RCC_ETHMAC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_ETHMACRST))
#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST))
-
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST))
#define __HAL_RCC_ETHMAC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_ETHMACRST))
#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST))
-
-/** @brief Force or release AHB2 peripheral reset.
- */
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
@@ -1398,15 +2035,32 @@
#define __HAL_RCC_CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST))
#define __HAL_RCC_HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST))
-
#endif /* STM32F415xx || STM32F417xx */
-
-/** @brief Force or release AHB3 peripheral reset
- */
+
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+
#define __HAL_RCC_FSMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FSMCRST))
#define __HAL_RCC_FSMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FSMCRST))
-
-/** @brief Force or release APB1 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
*/
#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
@@ -1419,7 +2073,17 @@
#define __HAL_RCC_CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST))
#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
-
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
@@ -1431,18 +2095,35 @@
#define __HAL_RCC_CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST))
#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
-
-/** @brief Force or release APB2 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
*/
#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET()(RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
-
-/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN))
@@ -1453,7 +2134,13 @@
#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN))
-
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN))
@@ -1464,13 +2151,28 @@
#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN))
-
-/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
- * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN))
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN))
+
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
@@ -1483,8 +2185,12 @@
#define __HAL_RCC_CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN))
#define __HAL_RCC_HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN))
#endif /* STM32F415xx || STM32F417xx */
-
-/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1492,8 +2198,12 @@
*/
#define __HAL_RCC_FSMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FSMCLPEN))
#define __HAL_RCC_FSMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FSMCLPEN))
-
-/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1510,7 +2220,17 @@
#define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN))
#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
-
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
@@ -1522,8 +2242,12 @@
#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN))
#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1532,16 +2256,421 @@
#define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN))
-
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
+/**
+ * @}
+ */
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */
-/*---------------------------------------------------------------------------------------------*/
-
-/*------------------------------------------ STM32F411xx --------------------------------------*/
-#if defined(STM32F411xE)
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/*----------------------------------------------------------------------------*/
+
+/*------------------------- STM32F401xE/STM32F401xC --------------------------*/
+#if defined(STM32F401xC) || defined(STM32F401xE)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB1_FORCE_RESET() (RCC->AHB1RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_AHB1_RELEASE_RESET() (RCC->AHB1RSTR = 0x00)
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB1RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00)
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00)
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
+/**
+ * @}
+ */
+#endif /* STM32F401xC || STM32F401xE*/
+/*----------------------------------------------------------------------------*/
+
+/*-------------------------------- STM32F410xx -------------------------------*/
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_RNGEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB1) peripheral clock.
+ */
+#define __HAL_RCC_TIM6_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_LPTIM1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_LPTIM1EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_LPTIM1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RTCAPB_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_FMPI2C1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_DAC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
+#define __HAL_RCC_RTCAPB_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_RTCAPBEN))
+#define __HAL_RCC_LPTIM1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_LPTIM1EN))
+#define __HAL_RCC_FMPI2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_FMPI2C1EN))
+#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
*/
#define __HAL_RCC_SPI5_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
@@ -1550,28 +2679,471 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\
UNUSED(tmpreg); \
} while(0)
-#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
-
-/** @brief Force or release APB2 peripheral reset.
- */
-#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
-#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_EXTIT_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
+#define __HAL_RCC_EXTIT_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_EXTITEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_RNGRST))
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_RNGRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET()
+#define __HAL_RCC_AHB2_RELEASE_RESET()
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
*/
-#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
-#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
-
-#endif /* STM32F411xE */
-/*---------------------------------------------------------------------------------------------*/
-
-/*----------------------------------------- STM32F446xx ---------------------------------------*/
-#if defined(STM32F446xx)
-/** @brief Enables or disables the AHB1 peripheral clock.
+#define __HAL_RCC_AHB3_FORCE_RESET()
+#define __HAL_RCC_AHB3_RELEASE_RESET()
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ */
+#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
+#define __HAL_RCC_LPTIM1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_LPTIM1RST))
+#define __HAL_RCC_FMPI2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_FMPI2C1RST))
+#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
+
+#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
+#define __HAL_RCC_LPTIM1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_LPTIM1RST))
+#define __HAL_RCC_FMPI2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_FMPI2C1RST))
+#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ */
+#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
+#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ */
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_RNGLPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_RNGLPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN))
+#define __HAL_RCC_LPTIM1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_LPTIM1LPEN))
+#define __HAL_RCC_RTCAPB_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_RTCAPBLPEN))
+#define __HAL_RCC_FMPI2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_FMPI2C1LPEN))
+#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
+
+#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
+#define __HAL_RCC_LPTIM1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_LPTIM1LPEN))
+#define __HAL_RCC_RTCAPB_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_RTCAPBLPEN))
+#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN))
+#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
+#define __HAL_RCC_EXTIT_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_EXTITLPEN))
+#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
+#define __HAL_RCC_EXTIT_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_EXTITLPEN))
+/**
+ * @}
+ */
+
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+/*----------------------------------------------------------------------------*/
+
+/*-------------------------------- STM32F411xx -------------------------------*/
+#if defined(STM32F411xE)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEX_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
+/**
+ * @}
+ */
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+ */
+#define __HAL_RCC_SPI5_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ */
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ */
+#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
+#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
+#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
+/**
+ * @}
+ */
+#endif /* STM32F411xE */
+/*----------------------------------------------------------------------------*/
+
+/*---------------------------------- STM32F446xx -----------------------------*/
+#if defined(STM32F446xx)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\
@@ -1600,13 +3172,21 @@
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
-
-/** @brief Enable or disable the AHB2 peripheral clock.
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1619,8 +3199,28 @@
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN))
-
-/** @brief Enables or disables the AHB3 peripheral clock.
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1642,8 +3242,12 @@
#define __HAL_RCC_FMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FMCEN))
#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN))
-
-/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1746,7 +3350,46 @@
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
@@ -1761,8 +3404,12 @@
#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN))
#define __HAL_RCC_CEC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CECEN))
#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
-
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1802,44 +3449,101 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN);\
UNUSED(tmpreg); \
} while(0)
-
-#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
-#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
-#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
-#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
-#define __HAL_RCC_SAI2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI2EN))
-
-/** @brief Force or release AHB1 peripheral reset.
- */
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
+#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
+#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
+#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
+#define __HAL_RCC_SAI2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI2EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST))
-
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST))
-
-/** @brief Force or release AHB2 peripheral reset.
- */
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
-
-/** @brief Force or release AHB3 peripheral reset
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
*/
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+
#define __HAL_RCC_FMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FMCRST))
#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST))
#define __HAL_RCC_FMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FMCRST))
#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST))
-
-/** @brief Force or release APB1 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
*/
#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST))
#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST))
#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST))
-#define __HAL_RCC_SPDIFRX_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPDIFRXRST))
+#define __HAL_RCC_SPDIFRX_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPDIFRXRST))
#define __HAL_RCC_USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST))
#define __HAL_RCC_UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST))
#define __HAL_RCC_UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST))
@@ -1848,7 +3552,17 @@
#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_CEC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CECRST))
#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
-
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
@@ -1863,44 +3577,86 @@
#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_CEC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CECRST))
#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
-
-/** @brief Force or release APB2 peripheral reset.
- */
-#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
-#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST))
-#define __HAL_RCC_SAI2_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI2RST))
-
-#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
-#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST))
-#define __HAL_RCC_SAI2_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI2RST))
-
-/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ */
+#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
+#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST))
+#define __HAL_RCC_SAI2_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI2RST))
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
+#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
+#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST))
+#define __HAL_RCC_SAI2_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI2RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM2LPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN))
-
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM2LPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN))
-/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
- * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN))
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN))
+
#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
-
-/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1911,8 +3667,12 @@
#define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FMCLPEN))
#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN))
-
-/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1923,7 +3683,7 @@
#define __HAL_RCC_TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN))
#define __HAL_RCC_TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN))
#define __HAL_RCC_TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN))
-#define __HAL_RCC_SPDIFRX_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPDIFRXLPEN))
+#define __HAL_RCC_SPDIFRX_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPDIFRXLPEN))
#define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN))
#define __HAL_RCC_UART4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART4LPEN))
#define __HAL_RCC_UART5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART5LPEN))
@@ -1932,23 +3692,37 @@
#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_CEC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CECLPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
-
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
#define __HAL_RCC_TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN))
#define __HAL_RCC_TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN))
-#define __HAL_RCC_SPDIFRX_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPDIFRXLPEN))
+#define __HAL_RCC_SPDIFRX_CLK_SLEEP_DISABLE()(RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPDIFRXLPEN))
#define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN))
#define __HAL_RCC_UART4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART4LPEN))
#define __HAL_RCC_UART5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART5LPEN))
-#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN))
+#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE()(RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN))
#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN))
#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_CEC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CECLPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1959,18 +3733,27 @@
#define __HAL_RCC_ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI1LPEN))
#define __HAL_RCC_SAI2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI2LPEN))
-
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI1LPEN))
#define __HAL_RCC_SAI2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI2LPEN))
+/**
+ * @}
+ */
#endif /* STM32F446xx */
-/*------------------------------------------------------------------------------------------------------------*/
-
-/*------------------------------------------------- PLL Configuration ----------------------------------------*/
-#if defined(STM32F446xx)
+/*----------------------------------------------------------------------------*/
+/*------------------------------- PLL Configuration --------------------------*/
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro to configure the main PLL clock source, multiplication and division factors.
* @note This function must be used only when the main PLL is disabled.
* @param __RCC_PLLSource__: specifies the PLL entry clock source.
@@ -1992,7 +3775,7 @@
* This parameter must be a number in the range {2, 4, 6, or 8}.
*
* @param __PLLQ__: specifies the division factor for OTG FS, SDIO and RNG clocks
- * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
* @note If the USB OTG FS is used in your application, you have to set the
* PLLQ parameter correctly to have 48 MHz clock for the USB. However,
* the SDIO and RNG need a frequency lower than or equal to 48 MHz to work
@@ -2000,7 +3783,7 @@
*
* @param __PLLR__: PLL division factor for I2S, SAI, SYSTEM, SPDIFRX clocks.
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
- * @note This parameter is only available in STM32F446xx devices.
+ * @note This parameter is only available in STM32F446xx/STM32F469xx/STM32F479xx devices.
*
*/
#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSource__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__,__PLLR__) \
@@ -2031,7 +3814,7 @@
* This parameter must be a number in the range {2, 4, 6, or 8}.
*
* @param __PLLQ__: specifies the division factor for OTG FS, SDIO and RNG clocks
- * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
* @note If the USB OTG FS is used in your application, you have to set the
* PLLQ parameter correctly to have 48 MHz clock for the USB. However,
* the SDIO and RNG need a frequency lower than or equal to 48 MHz to work
@@ -2043,10 +3826,23 @@
((__PLLN__) << POSITION_VAL(RCC_PLLCFGR_PLLN)) | \
((((__PLLP__) >> 1) -1) << POSITION_VAL(RCC_PLLCFGR_PLLP)) | \
((__PLLQ__) << POSITION_VAL(RCC_PLLCFGR_PLLQ))))
- #endif /* STM32F446xx */
-/*-------------------------------------------------------------------------------------------------------*/
-
-/*------------------------------------------- PLLI2S Configuration --------------------------------------*/
+ #endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*----------------------------PLLI2S Configuration ---------------------------*/
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+
+/** @brief Macros to enable or disable the PLLI2S.
+ * @note The PLLI2S is disabled by hardware when entering STOP and STANDBY modes.
+ */
+#define __HAL_RCC_PLLI2S_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = ENABLE)
+#define __HAL_RCC_PLLI2S_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = DISABLE)
+
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
#if defined(STM32F446xx)
/** @brief Macro to configure the PLLI2S clock multiplication and division factors .
* @note This macro must be used only when the PLLI2S is disabled.
@@ -2057,8 +3853,7 @@
* @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input
* frequency ranges from 1 to 2 MHz. It is recommended to select a frequency
* of 1 MHz to limit PLLI2S jitter.
- * @note The PLLI2SM parameter is only used with STM32F411xE and STM32F446xx Devices
- *
+ *
* @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock
* This parameter must be a number between Min_Data = 192 and Max_Data = 432.
* @note You have to set the PLLI2SN parameter correctly to ensure that the VCO
@@ -2075,15 +3870,13 @@
*
* @param __PLLI2SQ__: specifies the division factor for SAI clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 15.
- * @note the PLLI2SQ parameter is only available with STM32F427/437/429x/439xx Devices
- *
- */
-#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SP__, __PLLI2SQ__, __PLLI2SR__) \
- (RCC->PLLI2SCFGR = ((__PLLI2SM__) |\
- ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\
- ((((__PLLI2SP__) >> 1) -1) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) |\
- ((__PLLI2SQ__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)) |\
- ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
+ */
+#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SP__, __PLLI2SQ__, __PLLI2SR__) \
+ (RCC->PLLI2SCFGR = ((__PLLI2SM__) |\
+ ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\
+ ((((__PLLI2SP__) >> 1) -1) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) |\
+ ((__PLLI2SQ__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)) |\
+ ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
#else
/** @brief Macro to configure the PLLI2S clock multiplication and division factors .
* @note This macro must be used only when the PLLI2S is disabled.
@@ -2093,19 +3886,19 @@
* This parameter must be a number between Min_Data = 192 and Max_Data = 432.
* @note You have to set the PLLI2SN parameter correctly to ensure that the VCO
* output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
+ *
* @param __PLLI2SR__: specifies the division factor for I2S clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
* @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz
* on the I2S clock frequency.
- *
- */
-#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SN__, __PLLI2SR__) \
- (RCC->PLLI2SCFGR = (((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) | \
+ *
+ */
+#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SN__, __PLLI2SR__) \
+ (RCC->PLLI2SCFGR = (((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\
((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
#endif /* STM32F446xx */
#if defined(STM32F411xE)
-
/** @brief Macro to configure the PLLI2S clock multiplication and division factors .
* @note This macro must be used only when the PLLI2S is disabled.
* @note This macro must be used only when the PLLI2S is disabled.
@@ -2113,7 +3906,7 @@
* HAL_RCC_ClockConfig() API).
* @param __PLLI2SM__: specifies the division factor for PLLI2S VCO input clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 63.
- * @note The PLLI2SM parameter is only used with STM32F411xE Devices
+ * @note The PLLI2SM parameter is only used with STM32F411xE/STM32F410xx Devices
* @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input
* frequency ranges from 1 to 2 MHz. It is recommended to select a frequency
* of 2 MHz to limit PLLI2S jitter.
@@ -2131,7 +3924,7 @@
((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
#endif /* STM32F411xE */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro used by the SAI HAL driver to configure the PLLI2S clock multiplication and division factors.
* @note This macro must be used only when the PLLI2S is disabled.
* @note PLLI2S clock source is common with the main PLL (configured in
@@ -2142,8 +3935,8 @@
* output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
* @param __PLLI2SQ__: specifies the division factor for SAI1 clock.
* This parameter must be a number between Min_Data = 2 and Max_Data = 15.
- * @note the PLLI2SQ parameter is only available with STM32F427xx/437xx/429xx/439xx Devices
- * and can be configured using the __HAL_RCC_PLLI2S_PLLSAICLK_CONFIG() macro
+ * @note the PLLI2SQ parameter is only available with STM32F427xx/437xx/429xx/439xx/469xx/479xx
+ * Devices and can be configured using the __HAL_RCC_PLLI2S_PLLSAICLK_CONFIG() macro
* @param __PLLI2SR__: specifies the division factor for I2S clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
* @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz
@@ -2152,13 +3945,13 @@
#define __HAL_RCC_PLLI2S_SAICLK_CONFIG(__PLLI2SN__, __PLLI2SQ__, __PLLI2SR__) (RCC->PLLI2SCFGR = ((__PLLI2SN__) << 6) |\
((__PLLI2SQ__) << 24) |\
((__PLLI2SR__) << 28))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-/*----------------------------------------------------------------------------------------------------------------*/
-
-/*--------------------------------------------------- PLLSAI Configuration ---------------------------------------*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------------------ PLLSAI Configuration ------------------------*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macros to Enable or Disable the PLLISAI.
- * @note The PLLSAI is only available with STM32F429x/439x Devices.
+ * @note The PLLSAI is only available with STM32F429x/439x Devices.
* @note The PLLSAI is disabled by hardware when entering STOP and STANDBY modes.
*/
#define __HAL_RCC_PLLSAI_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLSAION_BB = ENABLE)
@@ -2196,6 +3989,30 @@
((((__PLLSAIP__) >> 1) -1) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) | \
((__PLLSAIQ__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ))))
#endif /* STM32F446xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+/** @brief Macro to configure the PLLSAI clock multiplication and division factors.
+ *
+ * @param __PLLSAIN__: specifies the multiplication factor for PLLSAI VCO output clock.
+ * This parameter must be a number between Min_Data = 192 and Max_Data = 432.
+ * @note You have to set the PLLSAIN parameter correctly to ensure that the VCO
+ * output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
+ *
+ * @param __PLLSAIP__: specifies division factor for SDIO and CLK48 clocks.
+ * This parameter must be a number in the range {2, 4, 6, or 8}.
+ *
+ * @param __PLLSAIQ__: specifies the division factor for SAI clock
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
+ *
+ * @param __PLLSAIR__: specifies the division factor for LTDC clock
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 7.
+ */
+#define __HAL_RCC_PLLSAI_CONFIG(__PLLSAIN__, __PLLSAIP__, __PLLSAIQ__, __PLLSAIR__) \
+ (RCC->PLLSAICFGR = (((__PLLSAIN__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)) |\
+ ((((__PLLSAIP__) >> 1) -1) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) |\
+ ((__PLLSAIQ__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)) |\
+ ((__PLLSAIR__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR))))
+#endif /* STM32F469xx || STM32F479xx */
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
/** @brief Macro to configure the PLLSAI clock multiplication and division factors.
@@ -2218,14 +4035,15 @@
((__PLLSAIR__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR))))
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
-/*----------------------------------------------------------------------------------------------------------------------*/
-
-/*----------------------------------------- PLLSAI/PLLI2S Dividers Configuration ---------------------------------------*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
-/** @brief Macro to configure the SAI clock Divider coming from PLLI2S.
- * @note This function must be called before enabling the PLLI2S.
- * @param __PLLI2SDivQ__: specifies the PLLI2S division factor for SAI1 clock .
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------- PLLSAI/PLLI2S Dividers Configuration -------------------*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @brief Macro to configure the SAI clock Divider coming from PLLI2S.
+ * @note This function must be called before enabling the PLLI2S.
+ * @param __PLLI2SDivQ__: specifies the PLLI2S division factor for SAI1 clock.
* This parameter must be a number between 1 and 32.
* SAI1 clock frequency = f(PLLI2SQ) / __PLLI2SDivQ__
*/
@@ -2238,25 +4056,26 @@
* SAI1 clock frequency = f(PLLSAIQ) / __PLLSAIDivQ__
*/
#define __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(__PLLSAIDivQ__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVQ, ((__PLLSAIDivQ__)-1)<<8))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro to configure the LTDC clock Divider coming from PLLSAI.
*
- * @note The LTDC peripheral is only available with STM32F427/437/429/439xx Devices.
+ * @note The LTDC peripheral is only available with STM32F427/437/429/439/469/479xx Devices.
* @note This function must be called before enabling the PLLSAI.
* @param __PLLSAIDivR__: specifies the PLLSAI division factor for LTDC clock .
* This parameter must be a number between Min_Data = 2 and Max_Data = 16.
* LTDC clock frequency = f(PLLSAIR) / __PLLSAIDivR__
- */
+ */
#define __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(__PLLSAIDivR__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVR, (__PLLSAIDivR__)))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-/*-----------------------------------------------------------------------------------------------------------------------------------*/
-
-/*-------------------------------------------------- Peripheral Clock selection -----------------------------------------------------*/
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------------- Peripheral Clock selection -----------------------*/
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\
defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F469xx) ||\
+ defined(STM32F479xx)
/** @brief Macro to configure the I2S clock source (I2SCLK).
* @note This function must be called before enabling the I2S APB clock.
* @param __SOURCE__: specifies the I2S clock source.
@@ -2266,12 +4085,12 @@
* used as I2S clock source.
*/
#define __HAL_RCC_I2S_CONFIG(__SOURCE__) (*(__IO uint32_t *) RCC_CFGR_I2SSRC_BB = (__SOURCE__))
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx */
+#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro to configure SAI1BlockA clock source selection.
- * @note The SAI peripheral is only available with STM32F427/437/429/439xx Devices.
+ * @note The SAI peripheral is only available with STM32F427/437/429/439/469/479xx Devices.
* @note This function must be called before enabling PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI Block A clock source.
@@ -2286,7 +4105,7 @@
#define __HAL_RCC_SAI_BLOCKACLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1ASRC, (__SOURCE__)))
/** @brief Macro to configure SAI1BlockB clock source selection.
- * @note The SAI peripheral is only available with STM32F427/437/429/439xx Devices.
+ * @note The SAI peripheral is only available with STM32F427/437/429/439/469/479xx Devices.
* @note This function must be called before enabling PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI Block B clock source.
@@ -2299,11 +4118,11 @@
* used as SAI1 Block B clock.
*/
#define __HAL_RCC_SAI_BLOCKBCLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1BSRC, (__SOURCE__)))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
#if defined(STM32F446xx)
/** @brief Macro to configure SAI1 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
+ * @note This configuration is only available with STM32F446xx Devices.
* @note This function must be called before enabling PLL, PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI1 clock source.
@@ -2349,7 +4168,6 @@
#define __HAL_RCC_GET_SAI2_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_SAI2SRC))
/** @brief Macro to configure I2S APB1 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @note This function must be called before enabling PLL, PLLI2S and the I2S clock.
* @param __SOURCE__: specifies the I2S APB1 clock source.
* This parameter can be one of the following values:
@@ -2361,7 +4179,6 @@
#define __HAL_RCC_I2S_APB1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC, (__SOURCE__)))
/** @brief Macro to Get I2S APB1 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @retval The clock source can be one of the following values:
* @arg RCC_I2SAPB1CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock.
* @arg RCC_I2SAPB1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock.
@@ -2371,7 +4188,6 @@
#define __HAL_RCC_GET_I2S_APB1_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC))
/** @brief Macro to configure I2S APB2 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @note This function must be called before enabling PLL, PLLI2S and the I2S clock.
* @param __SOURCE__: specifies the SAI Block A clock source.
* This parameter can be one of the following values:
@@ -2383,7 +4199,6 @@
#define __HAL_RCC_I2S_APB2_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S2SRC, (__SOURCE__)))
/** @brief Macro to Get I2S APB2 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @retval The clock source can be one of the following values:
* @arg RCC_I2SAPB2CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock.
* @arg RCC_I2SAPB2CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock.
@@ -2406,21 +4221,21 @@
* @arg RCC_CECCLKSOURCE_LSE: LSE selected as CEC clock
*/
#define __HAL_RCC_GET_CEC_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_CECSEL))
-
+
/** @brief Macro to configure the FMPI2C1 clock.
* @param __SOURCE__: specifies the FMPI2C1 clock source.
* This parameter can be one of the following values:
- * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as CEC clock
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
*/
#define __HAL_RCC_FMPI2C1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL, (uint32_t)(__SOURCE__)))
/** @brief Macro to Get the FMPI2C1 clock.
* @retval The clock source can be one of the following values:
- * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as CEC clock
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
*/
#define __HAL_RCC_GET_FMPI2C1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL))
@@ -2469,10 +4284,115 @@
*/
#define __HAL_RCC_GET_SPDIFRX_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_SPDIFRXSEL))
#endif /* STM32F446xx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\
- defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx)
-
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+
+/** @brief Macro to configure the CLK48 clock.
+ * @param __SOURCE__: specifies the CK48 clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_CK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CK48 clock.
+ * @arg RCC_CK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CK48 clock.
+ */
+#define __HAL_RCC_CLK48_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_CK48MSEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the CLK48 clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_CK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CK48 clock.
+ * @arg RCC_CK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CK48 clock.
+ */
+#define __HAL_RCC_GET_CLK48_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_CK48MSEL))
+
+/** @brief Macro to configure the SDIO clock.
+ * @param __SOURCE__: specifies the SDIO clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_SDIOCLKSOURCE_CK48: CK48 output used as SDIO clock.
+ * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock.
+ */
+#define __HAL_RCC_SDIO_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SDIOSEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the SDIO clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_SDIOCLKSOURCE_CK48: CK48 output used as SDIO clock.
+ * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock.
+ */
+#define __HAL_RCC_GET_SDIO_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_SDIOSEL))
+
+/** @brief Macro to configure the DSI clock.
+ * @param __SOURCE__: specifies the DSI clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_DSICLKSOURCE_PLLR: PLLR output used as DSI clock.
+ * @arg RCC_DSICLKSOURCE_DSIPHY: DSI-PHY output used as DSI clock.
+ */
+#define __HAL_RCC_DSI_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_DSISEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the DSI clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_DSICLKSOURCE_PLLR: PLLR output used as DSI clock.
+ * @arg RCC_DSICLKSOURCE_DSIPHY: DSI-PHY output used as DSI clock.
+ */
+#define __HAL_RCC_GET_DSI_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_DSISEL))
+
+#endif /* STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @brief Macro to configure I2S clock source selection.
+ * @param __SOURCE__: specifies the I2S clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_I2SAPBCLKSOURCE_PLLR: PLL VCO output clock divided by PLLR.
+ * @arg RCC_I2SAPBCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin.
+ * @arg RCC_I2SAPBCLKSOURCE_PLLSRC: HSI/HSE depends on PLLSRC.
+ */
+#define __HAL_RCC_I2S_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2SSRC, (__SOURCE__)))
+
+/** @brief Macro to Get I2S clock source selection.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_I2SAPBCLKSOURCE_PLLR: PLL VCO output clock divided by PLLR.
+ * @arg RCC_I2SAPBCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin.
+ * @arg RCC_I2SAPBCLKSOURCE_PLLSRC: HSI/HSE depends on PLLSRC.
+ */
+#define __HAL_RCC_GET_I2S_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2SSRC))
+
+/** @brief Macro to configure the FMPI2C1 clock.
+ * @param __SOURCE__: specifies the FMPI2C1 clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
+ */
+#define __HAL_RCC_FMPI2C1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the FMPI2C1 clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
+ */
+#define __HAL_RCC_GET_FMPI2C1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL))
+
+/** @brief Macro to configure the LPTIM1 clock.
+ * @param __SOURCE__: specifies the LPTIM1 clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_LPTIM1CLKSOURCE_PCLK: APB selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_HSI: HSI clock selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSI: LSI selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSE: LSE selected as LPTIM1 clock
+ */
+#define __HAL_RCC_LPTIM1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_LPTIM1SEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the LPTIM1 clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_LPTIM1CLKSOURCE_PCLK: APB selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_HSI: HSI clock selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSI: LSI selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSE: LSE selected as LPTIM1 clock
+ */
+#define __HAL_RCC_GET_LPTIM1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_LPTIM1SEL))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\
+ defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\
+ defined(STM32F479xx)
/** @brief Macro to configure the Timers clocks prescalers
* @note This feature is only available with STM32F429x/439x Devices.
* @param __PRESC__ : specifies the Timers clocks prescalers selection
@@ -2488,11 +4408,12 @@
*/
#define __HAL_RCC_TIMCLKPRESCALER(__PRESC__) (*(__IO uint32_t *) RCC_DCKCFGR_TIMPRE_BB = (__PRESC__))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx */
-
-/*-------------------------------------------------------------------------------------------------------------------*/
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE ||\
+ STM32F446xx || STM32F469xx || STM32F479xx */
+
+/*----------------------------------------------------------------------------*/
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Enable PLLSAI_RDY interrupt.
*/
#define __HAL_RCC_PLLSAI_ENABLE_IT() (RCC->CIR |= (RCC_CIR_PLLSAIRDYIE))
@@ -2515,7 +4436,27 @@
*/
#define __HAL_RCC_PLLSAI_GET_FLAG() ((RCC->CR & (RCC_CR_PLLSAIRDY)) == (RCC_CR_PLLSAIRDY))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @defgroup RCCEx_MCO1_Enable MCO1 Enable
+ * @brief Macros to enable or disable the RCC MCO1 feature.
+ */
+#define __HAL_RCC_MCO1_ENABLE() (*(__IO uint32_t *) RCC_CFGR_MCO1EN_BB = ENABLE)
+#define __HAL_RCC_MCO1_DISABLE() (*(__IO uint32_t *) RCC_CFGR_MCO1EN_BB = DISABLE)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_MCO2_Enable MCO2 Enable
+ * @brief Macros to enable or disable the RCC MCO2 feature.
+ */
+#define __HAL_RCC_MCO2_ENABLE() (*(__IO uint32_t *) RCC_CFGR_MCO2EN_BB = ENABLE)
+#define __HAL_RCC_MCO2_DISABLE() (*(__IO uint32_t *) RCC_CFGR_MCO2EN_BB = DISABLE)
+/**
+ * @}
+ */
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
/**
* @}
@@ -2536,9 +4477,10 @@
uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk);
#endif /* STM32F446xx */
-#if defined(STM32F411xE) || defined(STM32F446xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
void HAL_RCCEx_SelectLSEMode(uint8_t Mode);
-#endif /* STM32F411xE || STM32F446xx */
+#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
/**
* @}
*/
@@ -2558,20 +4500,60 @@
* @{
*/
/* --- CR Register ---*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/* Alias word address of PLLSAION bit */
#define RCC_PLLSAION_BIT_NUMBER 0x1C
#define RCC_CR_PLLSAION_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32) + (RCC_PLLSAION_BIT_NUMBER * 4))
+#define PLLSAI_TIMEOUT_VALUE ((uint32_t)100) /* Timeout value fixed to 100 ms */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/* Alias word address of PLLI2SON bit */
+#define RCC_PLLI2SON_BIT_NUMBER 0x1A
+#define RCC_CR_PLLI2SON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32) + (RCC_PLLI2SON_BIT_NUMBER * 4))
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
/* --- DCKCFGR Register ---*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
/* Alias word address of TIMPRE bit */
#define RCC_DCKCFGR_OFFSET (RCC_OFFSET + 0x8C)
#define RCC_TIMPRE_BIT_NUMBER 0x18
#define RCC_DCKCFGR_TIMPRE_BB (PERIPH_BB_BASE + (RCC_DCKCFGR_OFFSET * 32) + (RCC_TIMPRE_BIT_NUMBER * 4))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+/* --- CFGR Register ---*/
+#define RCC_CFGR_OFFSET (RCC_OFFSET + 0x08)
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/* Alias word address of I2SSRC bit */
+#define RCC_I2SSRC_BIT_NUMBER 0x17
+#define RCC_CFGR_I2SSRC_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_I2SSRC_BIT_NUMBER * 4))
+
+#define PLLI2S_TIMEOUT_VALUE ((uint32_t)100) /* Timeout value fixed to 100 ms */
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/* Alias word address of MCO1EN bit */
+#define RCC_MCO1EN_BIT_NUMBER 0x8
+#define RCC_CFGR_MCO1EN_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_MCO1EN_BIT_NUMBER * 4))
+
+/* Alias word address of MCO2EN bit */
+#define RCC_MCO2EN_BIT_NUMBER 0x9
+#define RCC_CFGR_MCO2EN_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_MCO2EN_BIT_NUMBER * 4))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
#define PLL_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
-
/**
* @}
*/
@@ -2589,23 +4571,32 @@
*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
-#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000002F))
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000007F))
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
-#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000003))
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000007))
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000001F))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
#if defined(STM32F446xx)
-#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x000007FF))
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000FFF))
#endif /* STM32F446xx */
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x000001FF))
+#endif /* STM32F469xx || STM32F479xx */
+
#define IS_RCC_PLLI2SN_VALUE(VALUE) ((192 <= (VALUE)) && ((VALUE) <= 432))
#define IS_RCC_PLLI2SR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F446xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define IS_RCC_PLLI2SQ_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 15))
#define IS_RCC_PLLSAIN_VALUE(VALUE) ((49 <= (VALUE)) && ((VALUE) <= 432))
@@ -2622,14 +4613,34 @@
((VALUE) == RCC_PLLSAIDIVR_4) ||\
((VALUE) == RCC_PLLSAIDIVR_8) ||\
((VALUE) == RCC_PLLSAIDIVR_16))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-
-#if defined(STM32F446xx) || defined(STM32F411xE)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F411xE) || defined(STM32F446xx)
#define IS_RCC_PLLI2SM_VALUE(VALUE) ((VALUE) <= 63)
#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\
((MODE) == RCC_LSE_HIGHDRIVE_MODE))
-#endif /* STM32F446xx || STM32F411xE */
+#endif /* STM32F411xE || STM32F446xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define IS_RCC_PLLR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
+
+#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\
+ ((MODE) == RCC_LSE_HIGHDRIVE_MODE))
+
+#define IS_RCC_FMPI2C1CLKSOURCE(SOURCE) (((SOURCE) == RCC_FMPI2C1CLKSOURCE_APB) ||\
+ ((SOURCE) == RCC_FMPI2C1CLKSOURCE_SYSCLK) ||\
+ ((SOURCE) == RCC_FMPI2C1CLKSOURCE_HSI))
+
+#define IS_RCC_LPTIM1CLKSOURCE(SOURCE) (((SOURCE) == RCC_LPTIM1CLKSOURCE_PCLK) ||\
+ ((SOURCE) == RCC_LPTIM1CLKSOURCE_HSI) ||\
+ ((SOURCE) == RCC_LPTIM1CLKSOURCE_LSI) ||\
+ ((SOURCE) == RCC_LPTIM1CLKSOURCE_LSE))
+
+#define IS_RCC_I2SAPBCLKSOURCE(SOURCE) (((SOURCE) == RCC_I2SAPBCLKSOURCE_PLLR) ||\
+ ((SOURCE) == RCC_I2SAPBCLKSOURCE_EXT) ||\
+ ((SOURCE) == RCC_I2SAPBCLKSOURCE_PLLSRC))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
#if defined(STM32F446xx)
#define IS_RCC_PLLR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
@@ -2679,10 +4690,46 @@
#define IS_RCC_SDIOCLKSOURCE(SOURCE) (((SOURCE) == RCC_SDIOCLKSOURCE_CK48) ||\
((SOURCE) == RCC_SDIOCLKSOURCE_SYSCLK))
-#define IS_RCC_SPDIFRXCLKSOURCE(SOURCE) (((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLR) ||\
+#define IS_RCC_SPDIFRXCLKSOURCE(SOURCE) (((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLR) ||\
((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLI2SP))
-#endif /* STM32F446xx */
-
+#endif /* STM32F446xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define IS_RCC_PLLR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
+
+#define IS_RCC_PLLSAIP_VALUE(VALUE) (((VALUE) == RCC_PLLSAIP_DIV2) ||\
+ ((VALUE) == RCC_PLLSAIP_DIV4) ||\
+ ((VALUE) == RCC_PLLSAIP_DIV6) ||\
+ ((VALUE) == RCC_PLLSAIP_DIV8))
+
+#define IS_RCC_CK48CLKSOURCE(SOURCE) (((SOURCE) == RCC_CK48CLKSOURCE_PLLQ) ||\
+ ((SOURCE) == RCC_CK48CLKSOURCE_PLLSAIP))
+
+#define IS_RCC_SDIOCLKSOURCE(SOURCE) (((SOURCE) == RCC_SDIOCLKSOURCE_CK48) ||\
+ ((SOURCE) == RCC_SDIOCLKSOURCE_SYSCLK))
+
+#define IS_RCC_DSIBYTELANECLKSOURCE(SOURCE) (((SOURCE) == RCC_DSICLKSOURCE_PLLR) ||\
+ ((SOURCE) == RCC_DSICLKSOURCE_DSIPHY))
+
+#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\
+ ((MODE) == RCC_LSE_HIGHDRIVE_MODE))
+#endif /* STM32F469xx || STM32F479xx */
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+
+#define IS_RCC_MCO2SOURCE(SOURCE) (((SOURCE) == RCC_MCO2SOURCE_SYSCLK) || ((SOURCE) == RCC_MCO2SOURCE_PLLI2SCLK)|| \
+ ((SOURCE) == RCC_MCO2SOURCE_HSE) || ((SOURCE) == RCC_MCO2SOURCE_PLLCLK))
+
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define IS_RCC_MCO2SOURCE(SOURCE) (((SOURCE) == RCC_MCO2SOURCE_SYSCLK) || ((SOURCE) == RCC_MCO2SOURCE_I2SCLK)|| \
+ ((SOURCE) == RCC_MCO2SOURCE_HSE) || ((SOURCE) == RCC_MCO2SOURCE_PLLCLK))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
/**
* @}
*/