Increasing time for which module remains in PSM.
Dependencies: ublox-at-cellular-interface ublox-cellular-base ublox-cellular-base-n2xx ublox-at-cellular-interface-n2xx
Diff: main.cpp
- Revision:
- 2:500c4fe5b9a4
- Parent:
- 0:4858efb34078
- Child:
- 3:6debe6b322c4
diff -r cae5c9c56a2f -r 500c4fe5b9a4 main.cpp --- a/main.cpp Fri May 03 15:53:33 2019 +0500 +++ b/main.cpp Mon Jun 24 15:12:21 2019 +0500 @@ -13,33 +13,27 @@ * See the License for the specific language governing permissions and * limitations under the License. */ - #include "mbed.h" #include "UbloxATCellularInterface.h" -#include "OnboardCellularInterface.h" #include "UbloxATCellularInterfaceN2xx.h" // You must select the correct interface library for your board, by // uncommenting the correct line below. Supported combinations are // indicated with a "Y" in the table below. // -// C030_U201 C030_N211 C027 -// UbloxATCellularInterface Y - Y -// OnboardCellularInterface Y - Y -// UbloxATCellularInterfaceN2xx - Y - +// C030_U201 C030_N211 C027 C030_R41XM +// UbloxATCellularInterface Y - Y Y +// UbloxATCellularInterfaceN2xx - Y - - // Note: the N211 module supports only UDP, not TCP -// OnboardCellularInterface uses LWIP and the PPP cellular interface -// on the mbed MCU, while using UbloxATCellularInterface and -// UbloxATCellularInterfaceN2xx uses an IP stack on the cellular -// module and hence uses less RAM (significant on C027). This also -// allows other AT command operations (e.g. sending an SMS) to happen +// UbloxATCellularInterface and UbloxATCellularInterfaceN2xx +// uses an IP stack on the cellular module and hence uses less RAM (significant on C027). +// This also allows other AT command operations (e.g. sending an SMS) to happen // during a data transfer (for which you should replace the // UbloxATCellularInterface library with the UbloxATCellularInterfaceExt // library). However, it is slower than using the LWIP/PPP on the mbed // MCU interface since more string parsing is required. #define INTERFACE_CLASS UbloxATCellularInterface -//#define INTERFACE_CLASS OnboardCellularInterface //#define INTERFACE_CLASS UbloxATCellularInterfaceN2xx // The credentials of the SIM in the board. If PIN checking is enabled @@ -56,11 +50,11 @@ #define APN NULL #define USERNAME NULL #define PASSWORD NULL - +#define TCP_SERVER "os.mbed.com" // Uncomment the following line to enable Icellular Current measurement. // Current drawn by modem is printed on serial every 2 seconds. -//#define CURRENT_MEASUREMENT +#define CURRENT_MEASUREMENT // LEDs DigitalOut ledRed(LED1, 1); @@ -132,7 +126,6 @@ static void cbButton() { buttonPressed = true; - //pulseEvent(); } void init_modem(INTERFACE_CLASS *interface) { @@ -183,10 +176,10 @@ #endif /* This example program for the u-blox C030-R410M board instantiates - * the UbloxATCellularInterface or OnboardCellularInterface and uses it - * to make a simple sockets connection to a server, using 2.pool.ntp.org - * for UDP and developer.mbed.org for TCP. It also showcases the 3GPP PSM - * feature. For a more comprehensive example, where higher layer protocols + * the UbloxATCellularInterface and uses it to make a simple sockets + * connection to a server, using 2.pool.ntp.org for UDP and + * developer.mbed.org for TCP. It also showcases the 3GPP PSM feature. + * For a more comprehensive example, where higher layer protocols * make use of the same sockets interface, see example-ublox-mbed-client. * Progress may be monitored with a serial terminal running at 9600 baud. * The LED on the C030 board will turn green when this program is @@ -274,14 +267,14 @@ } #endif - printf("Getting the IP address of \"developer.mbed.org\" and \"2.pool.ntp.org\"...\n"); + printf("\nGetting the IP address of \"" TCP_SERVER "\" and \"2.pool.ntp.org\"...\n"); if ((interface->gethostbyname("2.pool.ntp.org", &udpServer) == 0) && - (interface->gethostbyname("developer.mbed.org", &tcpServer) == 0)) { + (interface->gethostbyname(TCP_SERVER, &tcpServer) == 0)) { pulseEvent(); udpServer.set_port(123); printf("\"2.pool.ntp.org\" address: %s on port %d.\n", udpServer.get_ip_address(), udpServer.get_port()); - printf("\"developer.mbed.org\" address: %s on port %d.\n", tcpServer.get_ip_address(), tcpServer.get_port()); + printf("\"" TCP_SERVER "\" address: %s on port %d.\n", tcpServer.get_ip_address(), tcpServer.get_port()); tcpServer.set_port(80); printf("Performing socket operations in a loop (until the user button is pressed on C030 or forever on C027)...\n");