Diff: vendor/Freescale/KL25Z/hal/serial_api.c

Revision:

10:3bc89ef62ce7

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/vendor/Freescale/KL25Z/hal/serial_api.c	Fri Jun 14 17:49:17 2013 +0100
@@ -0,0 +1,296 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2013 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#include "serial_api.h"
+
+// math.h required for floating point operations for baud rate calculation
+#include <math.h>
+
+#include <string.h>
+
+#include "cmsis.h"
+#include "pinmap.h"
+#include "error.h"
+
+/******************************************************************************
+ * INITIALIZATION
+ ******************************************************************************/
+static const PinMap PinMap_UART_TX[] = {
+    {PTC4, UART_1, 3},
+    {PTA2, UART_0, 2},
+    {PTD5, UART_2, 3},
+    {PTD3, UART_2, 3},
+    {NC  , NC    , 0}
+};
+
+static const PinMap PinMap_UART_RX[] = {
+    {PTC3, UART_1, 3},
+    {PTA1, UART_0, 2},
+    {PTD4, UART_2, 3},
+    {PTD2, UART_2, 3},
+    {NC  , NC    , 0}
+};
+
+#define UART_NUM    3
+static uint32_t serial_irq_ids[UART_NUM] = {0};
+static uart_irq_handler irq_handler;
+
+int stdio_uart_inited = 0;
+serial_t stdio_uart;
+
+void serial_init(serial_t *obj, PinName tx, PinName rx) {
+    // determine the UART to use
+    UARTName uart_tx = (UARTName)pinmap_peripheral(tx, PinMap_UART_TX);
+    UARTName uart_rx = (UARTName)pinmap_peripheral(rx, PinMap_UART_RX);
+    UARTName uart = (UARTName)pinmap_merge(uart_tx, uart_rx);
+    if ((int)uart == NC) {
+        error("Serial pinout mapping failed");
+    }
+
+    obj->uart = (UARTLP_Type *)uart;
+    // enable clk
+    switch (uart) {
+        case UART_0: SIM->SOPT2 |= SIM_SOPT2_PLLFLLSEL_MASK | (1<<SIM_SOPT2_UART0SRC_SHIFT);
+                     SIM->SCGC5 |= SIM_SCGC5_PORTA_MASK; SIM->SCGC4 |= SIM_SCGC4_UART0_MASK; break;
+        case UART_1: SIM->SCGC5 |= SIM_SCGC5_PORTC_MASK; SIM->SCGC4 |= SIM_SCGC4_UART1_MASK; break;
+        case UART_2: SIM->SCGC5 |= SIM_SCGC5_PORTD_MASK; SIM->SCGC4 |= SIM_SCGC4_UART2_MASK; break;
+    }
+    // Disable UART before changing registers
+    obj->uart->C2 &= ~(UART_C2_RE_MASK | UART_C2_TE_MASK);
+    
+    switch (uart) {
+        case UART_0: obj->index = 0; break;
+        case UART_1: obj->index = 1; break;
+        case UART_2: obj->index = 2; break;
+    }
+
+    // set default baud rate and format
+    serial_baud  (obj, 9600);
+    serial_format(obj, 8, ParityNone, 1);
+
+    // pinout the chosen uart
+    pinmap_pinout(tx, PinMap_UART_TX);
+    pinmap_pinout(rx, PinMap_UART_RX);
+
+    // set rx/tx pins in PullUp mode
+    pin_mode(tx, PullUp);
+    pin_mode(rx, PullUp);
+
+    obj->uart->C2 |= (UART_C2_RE_MASK | UART_C2_TE_MASK);
+
+    if (uart == STDIO_UART) {
+        stdio_uart_inited = 1;
+        memcpy(&stdio_uart, obj, sizeof(serial_t));
+    }
+}
+
+void serial_free(serial_t *obj) {
+    serial_irq_ids[obj->index] = 0;
+}
+
+// serial_baud
+//
+// set the baud rate, taking in to account the current SystemFrequency
+//
+// The LPC2300 and LPC1700 have a divider and a fractional divider to control the
+// baud rate. The formula is:
+//
+// Baudrate = (1 / PCLK) * 16 * DL * (1 + DivAddVal / MulVal)
+//   where:
+//     1 < MulVal <= 15
+//     0 <= DivAddVal < 14
+//     DivAddVal < MulVal
+//
+void serial_baud(serial_t *obj, int baudrate) {
+    
+    // save C2 state
+    uint8_t c2_state = (obj->uart->C2 & (UART_C2_RE_MASK | UART_C2_TE_MASK));
+    
+    // Disable UART before changing registers
+    obj->uart->C2 &= ~(UART_C2_RE_MASK | UART_C2_TE_MASK);
+    
+    // [TODO] not hardcode this value
+    uint32_t PCLK = (obj->uart == UART0) ? 48000000u : 24000000u;
+
+    // First we check to see if the basic divide with no DivAddVal/MulVal
+    // ratio gives us an integer result. If it does, we set DivAddVal = 0,
+    // MulVal = 1. Otherwise, we search the valid ratio value range to find
+    // the closest match. This could be more elegant, using search methods
+    // and/or lookup tables, but the brute force method is not that much
+    // slower, and is more maintainable.
+    uint16_t DL = PCLK / (16 * baudrate);
+
+    // set BDH and BDL
+    obj->uart->BDH = (obj->uart->BDH & ~(0x1f)) | ((DL >> 8) & 0x1f);
+    obj->uart->BDL = (obj->uart->BDL & ~(0xff)) | ((DL >> 0) & 0xff);
+    
+    // restore C2 state
+    obj->uart->C2 |= c2_state;
+}
+
+void serial_format(serial_t *obj, int data_bits, SerialParity parity, int stop_bits) {
+    uint8_t m10 = 0;
+    
+    // save C2 state
+    uint8_t c2_state = (obj->uart->C2 & (UART_C2_RE_MASK | UART_C2_TE_MASK));
+    
+    // Disable UART before changing registers
+    obj->uart->C2 &= ~(UART_C2_RE_MASK | UART_C2_TE_MASK);
+    
+    // 8 data bits = 0 ... 9 data bits = 1
+    if ((data_bits < 8) || (data_bits > 9)) {
+        error("Invalid number of bits (%d) in serial format, should be 8..9\r\n", data_bits);
+    }
+    data_bits -= 8;
+
+    uint8_t parity_enable, parity_select;
+    switch (parity) {
+        case ParityNone: parity_enable = 0; parity_select = 0; break;
+        case ParityOdd : parity_enable = 1; parity_select = 1; data_bits++; break;
+        case ParityEven: parity_enable = 1; parity_select = 0; data_bits++; break;
+        default:
+            error("Invalid serial parity setting\r\n");
+            return;
+    }
+
+    // 1 stop bits = 0, 2 stop bits = 1
+    if ((stop_bits != 1) && (stop_bits != 2)) {
+        error("Invalid stop bits specified\r\n");
+    }
+    stop_bits -= 1;
+    
+    // 9 data bits + parity
+    if (data_bits == 2) {
+        // only uart0 supports 10 bit communication
+        if (obj->index != 0) {
+            error("Invalid number of bits (9) to be used with parity\r\n");
+        }
+        data_bits = 0;
+        m10 = 1;
+    }
+
+    // data bits, parity and parity mode
+    obj->uart->C1 = ((data_bits << 4)
+                  |  (parity_enable << 1)
+                  |  (parity_select << 0));
+    
+    // enable 10bit mode if needed
+    if (obj->index == 0) {
+        obj->uart->C4 &= ~UARTLP_C4_M10_MASK;
+        obj->uart->C4 |= (m10 << UARTLP_C4_M10_SHIFT);
+    }
+    
+    // stop bits
+    obj->uart->BDH &= ~UART_BDH_SBNS_MASK;
+    obj->uart->BDH |= (stop_bits << UART_BDH_SBNS_SHIFT);
+    
+    // restore C2 state
+    obj->uart->C2 |= c2_state;
+}
+
+/******************************************************************************
+ * INTERRUPTS HANDLING
+ ******************************************************************************/
+static inline void uart_irq(uint8_t status, uint32_t index) {
+    if (serial_irq_ids[index] != 0) {
+        if (status & UART_S1_TDRE_MASK)
+            irq_handler(serial_irq_ids[index], TxIrq);
+
+        if (status & UART_S1_RDRF_MASK)
+            irq_handler(serial_irq_ids[index], RxIrq);
+    }
+}
+
+void uart0_irq() {
+    uart_irq(UART0->S1, 0);
+    if (UART0->S1 & UART_S1_OR_MASK)
+        UART0->S1 |= UART_S1_OR_MASK;
+}
+void uart1_irq() {uart_irq(UART1->S1, 1);}
+void uart2_irq() {uart_irq(UART2->S1, 2);}
+
+void serial_irq_handler(serial_t *obj, uart_irq_handler handler, uint32_t id) {
+    irq_handler = handler;
+    serial_irq_ids[obj->index] = id;
+}
+
+void serial_irq_set(serial_t *obj, SerialIrq irq, uint32_t enable) {
+    IRQn_Type irq_n = (IRQn_Type)0;
+    uint32_t vector = 0;
+    switch ((int)obj->uart) {
+        case UART_0: irq_n=UART0_IRQn; vector = (uint32_t)&uart0_irq; break;
+        case UART_1: irq_n=UART1_IRQn; vector = (uint32_t)&uart1_irq; break;
+        case UART_2: irq_n=UART2_IRQn; vector = (uint32_t)&uart2_irq; break;
+    }
+
+    if (enable) {
+        switch (irq) {
+            case RxIrq: obj->uart->C2 |= (UART_C2_RIE_MASK); break;
+            case TxIrq: obj->uart->C2 |= (UART_C2_TIE_MASK); break;
+        }
+        NVIC_SetVector(irq_n, vector);
+        NVIC_EnableIRQ(irq_n);
+
+    } else { // disable
+        int all_disabled = 0;
+        SerialIrq other_irq = (irq == RxIrq) ? (TxIrq) : (RxIrq);
+        switch (irq) {
+            case RxIrq: obj->uart->C2 &= ~(UART_C2_RIE_MASK); break;
+            case TxIrq: obj->uart->C2 &= ~(UART_C2_TIE_MASK); break;
+        }
+        switch (other_irq) {
+            case RxIrq: all_disabled = (obj->uart->C2 & (UART_C2_RIE_MASK)) == 0; break;
+            case TxIrq: all_disabled = (obj->uart->C2 & (UART_C2_TIE_MASK)) == 0; break;
+        }
+        if (all_disabled)
+            NVIC_DisableIRQ(irq_n);
+    }
+}
+
+/******************************************************************************
+ * READ/WRITE
+ ******************************************************************************/
+int serial_getc(serial_t *obj) {
+    while (!serial_readable(obj));
+    return obj->uart->D;
+}
+
+void serial_putc(serial_t *obj, int c) {
+    while (!serial_writable(obj));
+    obj->uart->D = c;
+}
+
+int serial_readable(serial_t *obj) {
+    // check overrun
+    if (obj->uart->S1 &  UART_S1_OR_MASK) {
+        obj->uart->S1 |= UART_S1_OR_MASK;
+    }
+    return (obj->uart->S1 & UART_S1_RDRF_MASK);
+}
+
+int serial_writable(serial_t *obj) {
+    // check overrun
+    if (obj->uart->S1 &  UART_S1_OR_MASK) {
+        obj->uart->S1 |= UART_S1_OR_MASK;
+    }
+    return (obj->uart->S1 & UART_S1_TDRE_MASK);
+}
+
+void serial_clear(serial_t *obj) {
+}
+
+void serial_pinout_tx(PinName tx) {
+    pinmap_pinout(tx, PinMap_UART_TX);
+}