File content as of revision 70:08932e600a5e:

/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#include "mbed.h"
#include "iBeaconService.h"
#include "UARTService.h"

/**
 * For this demo application, populate the beacon advertisement load
 * with 2 AD structures: FLAG and MSD (manufacturer specific data).
 *
 * Reference:
 *  Bluetooth Core Specification 4.0 (Vol. 3), Part C, Section 11, 18
 */

BLEDevice ble;
UARTService *uart;

/**
 * The Beacon payload has the following composition:
 * 128-Bit / 16byte UUID = E2 0A 39 F4 73 F5 4B C4 A1 2F 17 D1 AD 07 A9 61
 * Major/Minor  = 0x1122 / 0x3344
 * Tx Power     = 0xC8 = 200, 2's compliment is 256-200 = (-56dB)
 *
 * Note: please remember to calibrate your beacons
 * TX Power for more accurate results.
 */
const uint8_t uuid[] = {0xE2, 0x0A, 0x39, 0xF4, 0x73, 0xF5, 0x4B, 0xC4,
                        0xA1, 0x2F, 0x17, 0xD1, 0xAD, 0x07, 0xA9, 0x62
                       };
uint16_t majorNumber = 1122;
uint16_t minorNumber = 3346;
uint16_t txPower = 0xC8;


const uint8_t b1_id   = 0x01;
const uint8_t b2_id   = 0x02;
const uint8_t b3_id   = 0x03;
const uint8_t b4_id   = 0x04;
const uint8_t b5_id   = 0x05;
const uint8_t b6_id   = 0x06;
const uint8_t b7_id   = 0x07;
const uint8_t b8_id   = 0x08;
const uint8_t b9_id   = 0x09;
const uint8_t b0_id   = 0x00;

const uint8_t bA1_id  = 0x31;
const uint8_t bA2_id  = 0x32;
const uint8_t bA3_id  = 0x33;
const uint8_t bA4_id  = 0x34;
const uint8_t bA5_id  = 0x35;
const uint8_t bA6_id  = 0x36;
const uint8_t bA7_id  = 0x37;
const uint8_t bA8_id  = 0x38;
const uint8_t bA9_id  = 0x39;
const uint8_t bA0_id  = 0x30;

int triger_base = 0;
int sense_base = 0;

AnalogIn   pin_sense_an  = P0_5;
PinName pin_sense        = P0_5;
PinName pin_triger       = P0_10;


//setup led
DigitalOut led1(P0_19);

//setup digital input/output
DigitalOut triger(pin_triger);
DigitalIn sensor(pin_sense);


void disconnectionCallback(Gap::Handle_t handle, Gap::DisconnectionReason_t reason);
void onDataWritten(const GattCharacteristicWriteCBParams *params);
int flip(char value);
void blinky(void);
void testAll(void);
void disconnectionCallback(Gap::Handle_t handle, Gap::DisconnectionReason_t reason)
{
    ble.startAdvertising();
}

void onDataWritten(const GattCharacteristicWriteCBParams *params)
{
    // TODO - this stuff will need to be retrofitted to deal with string commands
    /*
    if(*params->data == 0x33){
            led1 = 0;
    }
     else if(*params->data == 0x34){
            led1 = 1;
    }*/
    

}

int main(void)
{
    /* initialize stuff */
    led1 = 1;
    
    triger = triger_base = 0;
    sense_base = sensor.read();




    //testAll();
    
    ble.init();
    
    ble.onDisconnection(disconnectionCallback);
    ble.onDataWritten(onDataWritten);
    
    
    uart = new UARTService(ble);    
    iBeaconService ibeacon(ble, uuid, majorNumber, minorNumber, txPower);

    ble.setAdvertisingInterval(1000); /* 1000ms. */
    ble.startAdvertising();

    while(1)
    {
        //ble.waitForEvent(); // allows or low power operation
        if(sensor.read() == !sense_base)
        //if(pin_sense_an > 2.5f)
        {
            triger = !triger_base;
        }
        else
        {
            triger = triger_base;
        }
    }
}

void testAll(void)
{
    for(int i=0; i<2; i++)    
    {
        led1 = !led1;
        triger = !triger;
        wait(1);
    }
}

void blinky(void)
{
    for(int i=0; i<15; i++)    
    {
        led1 = !led1;
        wait(.3);
    }
}