fix LPC812 PWM
Fork of mbed-dev by
Diff: targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_rcc_ex.h
- Revision:
- 0:9b334a45a8ff
diff -r 000000000000 -r 9b334a45a8ff targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_rcc_ex.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_rcc_ex.h Thu Oct 01 15:25:22 2015 +0300 @@ -0,0 +1,1637 @@ +/** + ****************************************************************************** + * @file stm32l4xx_hal_rcc_ex.h + * @author MCD Application Team + * @version V1.0.0 + * @date 26-June-2015 + * @brief Header file of RCC HAL Extended module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32L4xx_HAL_RCC_EX_H +#define __STM32L4xx_HAL_RCC_EX_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l4xx_hal_def.h" + +/** @addtogroup STM32L4xx_HAL_Driver + * @{ + */ + +/** @addtogroup RCCEx + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup RCCEx_Exported_Types RCCEx Exported Types + * @{ + */ + +/** + * @brief PLLSAI1 Clock structure definition + */ +typedef struct +{ + + uint32_t PLLSAI1N; /*!< PLLSAI1N: specifies the multiplication factor for PLLSAI1 VCO output clock. + This parameter must be a number between 8 and 86. */ + + uint32_t PLLSAI1P; /*!< PLLSAI1P: specifies the division factor for SAI clock. + This parameter must be a value of @ref RCC_PLLP_Clock_Divider */ + + uint32_t PLLSAI1Q; /*!< PLLSAI1Q: specifies the division factor for USB/RNG/SDMMC1 clock. + This parameter must be a value of @ref RCC_PLLQ_Clock_Divider */ + + uint32_t PLLSAI1R; /*!< PLLSAI1R: specifies the division factor for ADC clock. + This parameter must be a value of @ref RCC_PLLR_Clock_Divider */ + + uint32_t PLLSAI1ClockOut; /*!< PLLSAIClockOut: specifies PLLSAI1 output clock to be enabled. + This parameter must be a value of @ref RCC_PLLSAI1_Clock_Output */ +}RCC_PLLSAI1InitTypeDef; + +/** + * @brief PLLSAI2 Clock structure definition + */ +typedef struct +{ + + uint32_t PLLSAI2N; /*!< PLLSAI2N: specifies the multiplication factor for PLLSAI2 VCO output clock. + This parameter must be a number between 8 and 86. */ + + uint32_t PLLSAI2P; /*!< PLLSAI2P: specifies the division factor for SAI clock. + This parameter must be a value of @ref RCC_PLLP_Clock_Divider */ + + uint32_t PLLSAI2R; /*!< PLLSAI2R: specifies the division factor for ADC clock. + This parameter must be a value of @ref RCC_PLLR_Clock_Divider */ + + uint32_t PLLSAI2ClockOut; /*!< PLLSAIClockOut: specifies PLLSAI2 output clock to be enabled. + This parameter must be a value of @ref RCC_PLLSAI2_Clock_Output */ +}RCC_PLLSAI2InitTypeDef; + +/** + * @brief RCC extended clocks structure definition + */ +typedef struct +{ + uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured. + This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */ + + RCC_PLLSAI1InitTypeDef PLLSAI1; /*!< PLLSAI1 structure parameters. + This parameter will be used only when PLLSAI1 is selected as Clock Source for SAI1, USB/RNG/SDMMC1 or ADC */ + + RCC_PLLSAI2InitTypeDef PLLSAI2; /*!< PLLSAI2 structure parameters. + This parameter will be used only when PLLSAI2 is selected as Clock Source for SAI2 or ADC */ + + uint32_t Usart1ClockSelection; /*!< Specifies USART1 clock source. + This parameter can be a value of @ref RCCEx_USART1_Clock_Source */ + + uint32_t Usart2ClockSelection; /*!< Specifies USART2 clock source. + This parameter can be a value of @ref RCCEx_USART2_Clock_Source */ + + uint32_t Usart3ClockSelection; /*!< Specifies USART3 clock source. + This parameter can be a value of @ref RCCEx_USART3_Clock_Source */ + + uint32_t Uart4ClockSelection; /*!< Specifies UART4 clock source. + This parameter can be a value of @ref RCCEx_UART4_Clock_Source */ + + uint32_t Uart5ClockSelection; /*!< Specifies UART5 clock source. + This parameter can be a value of @ref RCCEx_UART5_Clock_Source */ + + uint32_t Lpuart1ClockSelection; /*!< Specifies LPUART1 clock source. + This parameter can be a value of @ref RCCEx_LPUART1_Clock_Source */ + + uint32_t I2c1ClockSelection; /*!< Specifies I2C1 clock source. + This parameter can be a value of @ref RCCEx_I2C1_Clock_Source */ + + uint32_t I2c2ClockSelection; /*!< Specifies I2C2 clock source. + This parameter can be a value of @ref RCCEx_I2C2_Clock_Source */ + + uint32_t I2c3ClockSelection; /*!< Specifies I2C3 clock source. + This parameter can be a value of @ref RCCEx_I2C3_Clock_Source */ + + uint32_t Lptim1ClockSelection; /*!< Specifies LPTIM1 clock source. + This parameter can be a value of @ref RCCEx_LPTIM1_Clock_Source */ + + uint32_t Lptim2ClockSelection; /*!< Specifies LPTIM2 clock source. + This parameter can be a value of @ref RCCEx_LPTIM2_Clock_Source */ + + uint32_t Sai1ClockSelection; /*!< Specifies SAI1 clock source. + This parameter can be a value of @ref RCCEx_SAI1_Clock_Source */ + + uint32_t Sai2ClockSelection; /*!< Specifies SAI2 clock source. + This parameter can be a value of @ref RCCEx_SAI2_Clock_Source */ + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) + + uint32_t UsbClockSelection; /*!< Specifies USB clock source (warning: same source for SDMMC1 and RNG). + This parameter can be a value of @ref RCCEx_USB_Clock_Source */ + +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + + uint32_t Sdmmc1ClockSelection; /*!< Specifies SDMMC1 clock source (warning: same source for USB and RNG). + This parameter can be a value of @ref RCCEx_SDMMC1_Clock_Source */ + + uint32_t RngClockSelection; /*!< Specifies RNG clock source (warning: same source for USB and SDMMC1). + This parameter can be a value of @ref RCCEx_RNG_Clock_Source */ + + uint32_t AdcClockSelection; /*!< Specifies ADC interface clock source. + This parameter can be a value of @ref RCCEx_ADC_Clock_Source */ + + uint32_t Swpmi1ClockSelection; /*!< Specifies SWPMI1 clock source. + This parameter can be a value of @ref RCCEx_SWPMI1_Clock_Source */ + + uint32_t DfsdmClockSelection; /*!< Specifies DFSDM clock source. + This parameter can be a value of @ref RCCEx_DFSDM_Clock_Source */ + + uint32_t RTCClockSelection; /*!< Specifies RTC clock source. + This parameter can be a value of @ref RCC_RTC_Clock_Source */ +}RCC_PeriphCLKInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup RCCEx_Exported_Constants RCCEx Exported Constants + * @{ + */ + +/** @defgroup RCCEx_LSCO_Clock_Source Low Speed Clock Source + * @{ + */ +#define RCC_LSCOSOURCE_LSI (uint32_t)0x00000000 /*!< LSI selection for low speed clock output */ +#define RCC_LSCOSOURCE_LSE RCC_BDCR_LSCOSEL /*!< LSE selection for low speed clock output */ +/** + * @} + */ + +/** @defgroup RCCEx_Periph_Clock_Selection Periph Clock Selection + * @{ + */ +#define RCC_PERIPHCLK_USART1 ((uint32_t)0x00000001) +#define RCC_PERIPHCLK_USART2 ((uint32_t)0x00000002) +#define RCC_PERIPHCLK_USART3 ((uint32_t)0x00000004) +#define RCC_PERIPHCLK_UART4 ((uint32_t)0x00000008) +#define RCC_PERIPHCLK_UART5 ((uint32_t)0x00000010) +#define RCC_PERIPHCLK_LPUART1 ((uint32_t)0x00000020) +#define RCC_PERIPHCLK_I2C1 ((uint32_t)0x00000040) +#define RCC_PERIPHCLK_I2C2 ((uint32_t)0x00000080) +#define RCC_PERIPHCLK_I2C3 ((uint32_t)0x00000100) +#define RCC_PERIPHCLK_LPTIM1 ((uint32_t)0x00000200) +#define RCC_PERIPHCLK_LPTIM2 ((uint32_t)0x00000400) +#define RCC_PERIPHCLK_SAI1 ((uint32_t)0x00000800) +#define RCC_PERIPHCLK_SAI2 ((uint32_t)0x00001000) +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +#define RCC_PERIPHCLK_USB ((uint32_t)0x00002000) +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ +#define RCC_PERIPHCLK_ADC ((uint32_t)0x00004000) +#define RCC_PERIPHCLK_SWPMI1 ((uint32_t)0x00008000) +#define RCC_PERIPHCLK_DFSDM ((uint32_t)0x00010000) +#define RCC_PERIPHCLK_RTC ((uint32_t)0x00020000) +#define RCC_PERIPHCLK_RNG ((uint32_t)0x00040000) +#define RCC_PERIPHCLK_SDMMC1 ((uint32_t)0x00080000) +/** + * @} + */ + + +/** @defgroup RCCEx_USART1_Clock_Source USART1 Clock Source + * @{ + */ +#define RCC_USART1CLKSOURCE_PCLK2 ((uint32_t)0x00000000) +#define RCC_USART1CLKSOURCE_SYSCLK RCC_CCIPR_USART1SEL_0 +#define RCC_USART1CLKSOURCE_HSI RCC_CCIPR_USART1SEL_1 +#define RCC_USART1CLKSOURCE_LSE (RCC_CCIPR_USART1SEL_0 | RCC_CCIPR_USART1SEL_1) +/** + * @} + */ + +/** @defgroup RCCEx_USART2_Clock_Source USART2 Clock Source + * @{ + */ +#define RCC_USART2CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_USART2CLKSOURCE_SYSCLK RCC_CCIPR_USART2SEL_0 +#define RCC_USART2CLKSOURCE_HSI RCC_CCIPR_USART2SEL_1 +#define RCC_USART2CLKSOURCE_LSE (RCC_CCIPR_USART2SEL_0 | RCC_CCIPR_USART2SEL_1) +/** + * @} + */ + +/** @defgroup RCCEx_USART3_Clock_Source USART3 Clock Source + * @{ + */ +#define RCC_USART3CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_USART3CLKSOURCE_SYSCLK RCC_CCIPR_USART3SEL_0 +#define RCC_USART3CLKSOURCE_HSI RCC_CCIPR_USART3SEL_1 +#define RCC_USART3CLKSOURCE_LSE (RCC_CCIPR_USART3SEL_0 | RCC_CCIPR_USART3SEL_1) +/** + * @} + */ + +/** @defgroup RCCEx_UART4_Clock_Source UART4 Clock Source + * @{ + */ +#define RCC_UART4CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_UART4CLKSOURCE_SYSCLK RCC_CCIPR_UART4SEL_0 +#define RCC_UART4CLKSOURCE_HSI RCC_CCIPR_UART4SEL_1 +#define RCC_UART4CLKSOURCE_LSE (RCC_CCIPR_UART4SEL_0 | RCC_CCIPR_UART4SEL_1) +/** + * @} + */ + +/** @defgroup RCCEx_UART5_Clock_Source UART5 Clock Source + * @{ + */ +#define RCC_UART5CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_UART5CLKSOURCE_SYSCLK RCC_CCIPR_UART5SEL_0 +#define RCC_UART5CLKSOURCE_HSI RCC_CCIPR_UART5SEL_1 +#define RCC_UART5CLKSOURCE_LSE (RCC_CCIPR_UART5SEL_0 | RCC_CCIPR_UART5SEL_1) +/** + * @} + */ + +/** @defgroup RCCEx_LPUART1_Clock_Source LPUART1 Clock Source + * @{ + */ +#define RCC_LPUART1CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_LPUART1CLKSOURCE_SYSCLK RCC_CCIPR_LPUART1SEL_0 +#define RCC_LPUART1CLKSOURCE_HSI RCC_CCIPR_LPUART1SEL_1 +#define RCC_LPUART1CLKSOURCE_LSE (RCC_CCIPR_LPUART1SEL_0 | RCC_CCIPR_LPUART1SEL_1) +/** + * @} + */ + +/** @defgroup RCCEx_I2C1_Clock_Source I2C1 Clock Source + * @{ + */ +#define RCC_I2C1CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_I2C1CLKSOURCE_SYSCLK RCC_CCIPR_I2C1SEL_0 +#define RCC_I2C1CLKSOURCE_HSI RCC_CCIPR_I2C1SEL_1 +/** + * @} + */ + +/** @defgroup RCCEx_I2C2_Clock_Source I2C2 Clock Source + * @{ + */ +#define RCC_I2C2CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_I2C2CLKSOURCE_SYSCLK RCC_CCIPR_I2C2SEL_0 +#define RCC_I2C2CLKSOURCE_HSI RCC_CCIPR_I2C2SEL_1 +/** + * @} + */ + +/** @defgroup RCCEx_I2C3_Clock_Source I2C3 Clock Source + * @{ + */ +#define RCC_I2C3CLKSOURCE_PCLK1 ((uint32_t)0x00000000) +#define RCC_I2C3CLKSOURCE_SYSCLK RCC_CCIPR_I2C3SEL_0 +#define RCC_I2C3CLKSOURCE_HSI RCC_CCIPR_I2C3SEL_1 +/** + * @} + */ + +/** @defgroup RCCEx_SAI1_Clock_Source SAI1 Clock Source + * @{ + */ +#define RCC_SAI1CLKSOURCE_PLLSAI1 ((uint32_t)0x00000000) +#define RCC_SAI1CLKSOURCE_PLLSAI2 RCC_CCIPR_SAI1SEL_0 +#define RCC_SAI1CLKSOURCE_PLL RCC_CCIPR_SAI1SEL_1 +#define RCC_SAI1CLKSOURCE_PIN RCC_CCIPR_SAI1SEL +/** + * @} + */ + +/** @defgroup RCCEx_SAI2_Clock_Source SAI2 Clock Source + * @{ + */ +#define RCC_SAI2CLKSOURCE_PLLSAI1 ((uint32_t)0x00000000) +#define RCC_SAI2CLKSOURCE_PLLSAI2 RCC_CCIPR_SAI2SEL_0 +#define RCC_SAI2CLKSOURCE_PLL RCC_CCIPR_SAI2SEL_1 +#define RCC_SAI2CLKSOURCE_PIN RCC_CCIPR_SAI2SEL +/** + * @} + */ + +/** @defgroup RCCEx_LPTIM1_Clock_Source LPTIM1 Clock Source + * @{ + */ +#define RCC_LPTIM1CLKSOURCE_PCLK ((uint32_t)0x00000000) +#define RCC_LPTIM1CLKSOURCE_LSI RCC_CCIPR_LPTIM1SEL_0 +#define RCC_LPTIM1CLKSOURCE_HSI RCC_CCIPR_LPTIM1SEL_1 +#define RCC_LPTIM1CLKSOURCE_LSE RCC_CCIPR_LPTIM1SEL +/** + * @} + */ + +/** @defgroup RCCEx_LPTIM2_Clock_Source LPTIM2 Clock Source + * @{ + */ +#define RCC_LPTIM2CLKSOURCE_PCLK ((uint32_t)0x00000000) +#define RCC_LPTIM2CLKSOURCE_LSI RCC_CCIPR_LPTIM2SEL_0 +#define RCC_LPTIM2CLKSOURCE_HSI RCC_CCIPR_LPTIM2SEL_1 +#define RCC_LPTIM2CLKSOURCE_LSE RCC_CCIPR_LPTIM2SEL +/** + * @} + */ + +/** @defgroup RCCEx_SDMMC1_Clock_Source SDMMC1 Clock Source + * @{ + */ +#define RCC_SDMMC1CLKSOURCE_NONE ((uint32_t)0x00000000) +#define RCC_SDMMC1CLKSOURCE_PLLSAI1 RCC_CCIPR_CLK48SEL_0 +#define RCC_SDMMC1CLKSOURCE_PLL RCC_CCIPR_CLK48SEL_1 +#define RCC_SDMMC1CLKSOURCE_MSI RCC_CCIPR_CLK48SEL +/** + * @} + */ + +/** @defgroup RCCEx_RNG_Clock_Source RNG Clock Source + * @{ + */ +#define RCC_RNGCLKSOURCE_NONE ((uint32_t)0x00000000) +#define RCC_RNGCLKSOURCE_PLLSAI1 RCC_CCIPR_CLK48SEL_0 +#define RCC_RNGCLKSOURCE_PLL RCC_CCIPR_CLK48SEL_1 +#define RCC_RNGCLKSOURCE_MSI RCC_CCIPR_CLK48SEL +/** + * @} + */ + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +/** @defgroup RCCEx_USB_Clock_Source USB Clock Source + * @{ + */ +#define RCC_USBCLKSOURCE_NONE ((uint32_t)0x00000000) +#define RCC_USBCLKSOURCE_PLLSAI1 RCC_CCIPR_CLK48SEL_0 +#define RCC_USBCLKSOURCE_PLL RCC_CCIPR_CLK48SEL_1 +#define RCC_USBCLKSOURCE_MSI RCC_CCIPR_CLK48SEL +/** + * @} + */ +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + +/** @defgroup RCCEx_ADC_Clock_Source ADC Clock Source + * @{ + */ +#define RCC_ADCCLKSOURCE_NONE ((uint32_t)0x00000000) +#define RCC_ADCCLKSOURCE_PLLSAI1 RCC_CCIPR_ADCSEL_0 +#define RCC_ADCCLKSOURCE_PLLSAI2 RCC_CCIPR_ADCSEL_1 +#define RCC_ADCCLKSOURCE_SYSCLK RCC_CCIPR_ADCSEL +/** + * @} + */ + +/** @defgroup RCCEx_SWPMI1_Clock_Source SWPMI1 Clock Source + * @{ + */ +#define RCC_SWPMI1CLKSOURCE_PCLK ((uint32_t)0x00000000) +#define RCC_SWPMI1CLKSOURCE_HSI RCC_CCIPR_SWPMI1SEL +/** + * @} + */ + +/** @defgroup RCCEx_DFSDM_Clock_Source DFSDM Clock Source + * @{ + */ +#define RCC_DFSDMCLKSOURCE_PCLK ((uint32_t)0x00000000) +#define RCC_DFSDMCLKSOURCE_SYSCLK RCC_CCIPR_DFSDMSEL +/** + * @} + */ + +/** + * @} + */ + +/* Exported macros -----------------------------------------------------------*/ +/** @defgroup RCCEx_Exported_Macros RCCEx Exported Macros + * @{ + */ + +/** @defgroup RCCEx_Peripheral_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable + * @brief Enable or disable the AHB2 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN); \ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN); \ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN); +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + + +#if defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_AES_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN); \ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN); \ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_AES_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN); +#endif /* STM32L485xx || STM32L486xx */ + +/** + * @} + */ + +/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable + * @brief Enable or disable the APB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#if defined(STM32L476xx) || defined(STM32L486xx) +#define __HAL_RCC_LCD_CLK_ENABLE() do { \ + __IO uint32_t tmpreg; \ + SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN); \ + /* Delay after an RCC peripheral clock enabling */ \ + tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN); \ + UNUSED(tmpreg); \ + } while(0) + +#define __HAL_RCC_LCD_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN); +#endif /* STM32L476xx || STM32L486xx */ + +/** + * @} + */ + +/** @defgroup RCCEx_Peripheral_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enable Disable Status + * @brief Macros to get the status of the AHB2 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L486xx) +#define __HAL_RCC_USB_OTG_FS_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN) != RESET) + +#define __HAL_RCC_USB_OTG_FS_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_OTGFSEN) == RESET) +#endif /* STM32L475xx || STM32L476xx || STM32L486xx */ + + +#if defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_AES_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN) != RESET) + +#define __HAL_RCC_AES_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_AESEN) == RESET) +#endif /* STM32L485xx || STM32L486xx */ + +/** + * @} + */ + +/** @defgroup RCCEx_APB1_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status + * @brief Macros to get the status of the APB1 peripheral clock. + * @note After reset, the peripheral clock (used for registers read/write access) + * is disabled and the application software has to enable this clock before + * using it. + * @{ + */ +#if defined(STM32L476xx) || defined(STM32L486xx) +#define __HAL_RCC_LCD_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN) != RESET) + +#define __HAL_RCC_LCD_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LCDEN) == RESET) +#endif /* STM32L476xx || STM32L486xx */ + +/** + * @} + */ + +/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Peripheral Force Release Reset + * @brief Force or release AHB2 peripheral reset. + * @{ + */ + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_OTGFSRST) + +#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_OTGFSRST) +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + +#if defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_AES_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_AESRST) + +#define __HAL_RCC_AES_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_AESRST) +#endif /* STM32L485xx || STM32L486xx */ + +/** + * @} + */ + + +/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Peripheral Force Release Reset + * @brief Force or release APB1 peripheral reset. + * @{ + */ +#if defined(STM32L476xx) || defined(STM32L486xx) +#define __HAL_RCC_LCD_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LCDRST) + +#define __HAL_RCC_LCD_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LCDRST) +#endif /* STM32L476xx || STM32L486xx */ + +/** + * @} + */ + + +/** @defgroup RCCEx_AHB2_Clock_Sleep_Enable_Disable AHB2 Peripheral Clock Sleep Enable Disable + * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode. + * @note Peripheral clock gating in SLEEP mode can be used to further reduce + * power consumption. + * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. + * @note By default, all peripheral clocks are enabled during SLEEP mode. + * @{ + */ + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) + +#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + +#if defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_AES_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) + +#define __HAL_RCC_AES_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) +#endif /* STM32L485xx || STM32L486xx */ + +/** + * @} + */ + + +/** @defgroup RCCEx_APB1_Clock_Sleep_Enable_Disable APB1 Peripheral Clock Sleep Enable Disable + * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode. + * @note Peripheral clock gating in SLEEP mode can be used to further reduce + * power consumption. + * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. + * @note By default, all peripheral clocks are enabled during SLEEP mode. + * @{ + */ + +#if defined(STM32L476xx) || defined(STM32L486xx) +#define __HAL_RCC_LCD_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) + +#define __HAL_RCC_LCD_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) +#endif /* STM32L476xx || STM32L486xx */ + +/** + * @} + */ + +/** @defgroup RCCEx_AHB2_Clock_Sleep_Enable_Disable_Status AHB2 Peripheral Clock Sleep Enable Disable Status + * @brief Macros to get the status of the AHB2 peripheral clock during Low Power (Sleep) mode. + * @note Peripheral clock gating in SLEEP mode can be used to further reduce + * power consumption. + * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. + * @note By default, all peripheral clocks are enabled during SLEEP mode. + * @{ + */ + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_USB_OTG_FS_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) != RESET) + +#define __HAL_RCC_USB_OTG_FS_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_OTGFSSMEN) == RESET) +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + +#if defined(STM32L485xx) || defined(STM32L486xx) +#define __HAL_RCC_AES_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) != RESET) + +#define __HAL_RCC_AES_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_AESSMEN) == RESET) +#endif /* STM32L485xx || STM32L486xx */ + +/** + * @} + */ + + +/** @defgroup RCCEx_APB1_Clock_Sleep_Enable_Disable_Status APB1 Peripheral Clock Sleep Enable Disable Status + * @brief Macros to get the status of the APB1 peripheral clock during Low Power (Sleep) mode. + * @note Peripheral clock gating in SLEEP mode can be used to further reduce + * power consumption. + * @note After wakeup from SLEEP mode, the peripheral clock is enabled again. + * @note By default, all peripheral clocks are enabled during SLEEP mode. + * @{ + */ + +#if defined(STM32L476xx) || defined(STM32L486xx) +#define __HAL_RCC_LCD_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) != RESET) + +#define __HAL_RCC_LCD_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LCDSMEN) == RESET) +#endif /* STM32L476xx || STM32L486xx */ + +/** + * @} + */ + +/** + * @brief Macro to configure the PLLSAI1 clock multiplication and division factors. + * + * @note This function must be used only when the PLLSAI1 is disabled. + * @note PLLSAI1 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI1N__: specifies the multiplication factor for PLLSAI1 VCO output clock. + * This parameter must be a number between 8 and 86. + * @note You have to set the PLLSAI1N parameter correctly to ensure that the VCO + * output frequency is between 64 and 344 MHz. + * PLLSAI1 clock frequency = f(PLLSAI1) multiplied by PLLSAI1N + * + * @param __PLLSAI1P__: specifies the division factor for SAI clock. + * This parameter must be a number in the range (7 or 17). + * SAI1 clock frequency = f(PLLSAI1) / PLLSAI1P + * + * @param __PLLSAI1Q__: specifies the division factor for USB/RNG/SDMMC1 clock. + * This parameter must be in the range (2, 4, 6 or 8). + * USB/RNG/SDMMC1 clock frequency = f(PLLSAI1) / PLLSAI1Q + * + * @param __PLLSAI1R__: specifies the division factor for SAR ADC clock. + * This parameter must be in the range (2, 4, 6 or 8). + * ADC clock frequency = f(PLLSAI1) / PLLSAI1R + * + * @retval None + */ +#define __HAL_RCC_PLLSAI1_CONFIG(__PLLSAI1N__, __PLLSAI1P__, __PLLSAI1Q__, __PLLSAI1R__) \ + WRITE_REG(RCC->PLLSAI1CFGR, ((__PLLSAI1N__) << 8U) | (((__PLLSAI1P__) >> 4U) << 17U) | \ + ((((__PLLSAI1Q__) >> 1U) - 1) << 21U) | ((((__PLLSAI1R__) >> 1U) - 1) << 25U)) + +/** + * @brief Macro to configure the PLLSAI1 clock multiplication factor N. + * + * @note This function must be used only when the PLLSAI1 is disabled. + * @note PLLSAI1 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI1N__: specifies the multiplication factor for PLLSAI1 VCO output clock. + * This parameter must be a number between 8 and 86. + * @note You have to set the PLLSAI1N parameter correctly to ensure that the VCO + * output frequency is between 64 and 344 MHz. + * Use to set PLLSAI1 clock frequency = f(PLLSAI1) multiplied by PLLSAI1N + * + * @retval None + */ +#define __HAL_RCC_PLLSAI1_MULN_CONFIG(__PLLSAI1N__) \ + MODIFY_REG(RCC->PLLSAI1CFGR, RCC_PLLSAI1CFGR_PLLSAI1N, (__PLLSAI1N__) << 8U) + +/** @brief Macro to configure the PLLSAI1 clock division factor P. + * + * @note This function must be used only when the PLLSAI1 is disabled. + * @note PLLSAI1 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI1P__: specifies the division factor for SAI clock. + * This parameter must be a number in the range (7 or 17). + * Use to set SAI1 clock frequency = f(PLLSAI1) / PLLSAI1P + * + * @retval None + */ +#define __HAL_RCC_PLLSAI1_DIVP_CONFIG(__PLLSAI1P__) \ + MODIFY_REG(RCC->PLLSAI1CFGR, RCC_PLLSAI1CFGR_PLLSAI1P, ((__PLLSAI1P__) >> 4U) << 17U) + +/** @brief Macro to configure the PLLSAI1 clock division factor Q. + * + * @note This function must be used only when the PLLSAI1 is disabled. + * @note PLLSAI1 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI1Q__: specifies the division factor for USB/RNG/SDMMC1 clock. + * This parameter must be in the range (2, 4, 6 or 8). + * Use to set USB/RNG/SDMMC1 clock frequency = f(PLLSAI1) / PLLSAI1Q + * + * @retval None + */ +#define __HAL_RCC_PLLSAI1_DIVQ_CONFIG(__PLLSAI1Q__) \ + MODIFY_REG(RCC->PLLSAI1CFGR, RCC_PLLSAI1CFGR_PLLSAI1Q, (((__PLLSAI1Q__) >> 1U) - 1) << 21U) + +/** @brief Macro to configure the PLLSAI1 clock division factor R. + * + * @note This function must be used only when the PLLSAI1 is disabled. + * @note PLLSAI1 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI1R__: specifies the division factor for ADC clock. + * This parameter must be in the range (2, 4, 6 or 8) + * Use to set ADC clock frequency = f(PLLSAI1) / PLLSAI1R + * + * @retval None + */ +#define __HAL_RCC_PLLSAI1_DIVR_CONFIG(__PLLSAI1R__) \ + MODIFY_REG(RCC->PLLSAI1CFGR, RCC_PLLSAI1CFGR_PLLSAI1R, (((__PLLSAI1R__) >> 1U) - 1) << 25U) + +/** + * @brief Macros to enable or disable the PLLSAI1. + * @note The PLLSAI1 is disabled by hardware when entering STOP and STANDBY modes. + * @retval None + */ + +#define __HAL_RCC_PLLSAI1_ENABLE() SET_BIT(RCC->CR, RCC_CR_PLLSAI1ON) + +#define __HAL_RCC_PLLSAI1_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_PLLSAI1ON) + +/** + * @brief Macros to enable or disable each clock output (PLLSAI1_SAI1, PLLSAI1_USB2 and PLLSAI1_ADC1). + * @note Enabling and disabling those clocks can be done without the need to stop the PLL. + * This is mainly used to save Power. + * @param __PLLSAI1_CLOCKOUT__: specifies the PLLSAI1 clock to be output. + * This parameter can be one or a combination of the following values: + * @arg RCC_PLLSAI1_SAI1CLK: This clock is used to generate an accurate clock to achieve + * high-quality audio performance on SAI interface in case. + * @arg RCC_PLLSAI1_USB2CLK: This clock is used to generate the clock for the USB OTG FS (48 MHz), + * the random number generator (<=48 MHz) and the SDIO (<= 48 MHz). + * @arg RCC_PLLSAI1_ADC1CLK: Clock used to clock ADC peripheral. + * @retval None + */ + +#define __HAL_RCC_PLLSAI1CLKOUT_ENABLE(__PLLSAI1_CLOCKOUT__) SET_BIT(RCC->PLLSAI1CFGR, (__PLLSAI1_CLOCKOUT__)) + +#define __HAL_RCC_PLLSAI1CLKOUT_DISABLE(__PLLSAI1_CLOCKOUT__) CLEAR_BIT(RCC->PLLSAI1CFGR, (__PLLSAI1_CLOCKOUT__)) + +/** + * @brief Macro to get clock output enable status (PLLSAI1_SAI1, PLLSAI1_USB2 and PLLSAI1_ADC1). + * @param __PLLSAI1_CLOCKOUT__: specifies the PLLSAI1 clock to be output. + * This parameter can be one of the following values: + * @arg RCC_PLLSAI1_SAI1CLK: This clock is used to generate an accurate clock to achieve + * high-quality audio performance on SAI interface in case. + * @arg RCC_PLLSAI1_USB2CLK: This clock is used to generate the clock for the USB OTG FS (48 MHz), + * the random number generator (<=48 MHz) and the SDIO (<= 48 MHz). + * @arg RCC_PLLSAI1_ADC1CLK: Clock used to clock ADC peripheral. + * @retval SET / RESET + */ +#define __HAL_RCC_GET_PLLSAI1CLKOUT_CONFIG(__PLLSAI1_CLOCKOUT__) READ_BIT(RCC->PLLSAI1CFGR, (__PLLSAI1_CLOCKOUT__)) + +/** + * @brief Macro to configure the PLLSAI2 clock multiplication and division factors. + * + * @note This function must be used only when the PLLSAI2 is disabled. + * @note PLLSAI2 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI2N__: specifies the multiplication factor for PLLSAI2 VCO output clock. + * This parameter must be a number between 8 and 86. + * @note You have to set the PLLSAI2N parameter correctly to ensure that the VCO + * output frequency is between 64 and 344 MHz. + * + * @param __PLLSAI2P__: specifies the division factor for SAI clock. + * This parameter must be a number in the range (7 or 17). + * + * + * @param __PLLSAI2R__: specifies the division factor for SAR ADC clock. + * This parameter must be in the range (2, 4, 6 or 8) + * + * @retval None + */ + +#define __HAL_RCC_PLLSAI2_CONFIG(__PLLSAI2N__, __PLLSAI2P__, __PLLSAI2R__) \ + WRITE_REG(RCC->PLLSAI2CFGR, ((__PLLSAI2N__) << 8U) | (((__PLLSAI2P__) >> 4U) << 17U) | \ + ((((__PLLSAI2R__) >> 1U) - 1) << 25U)) + +/** + * @brief Macro to configure the PLLSAI2 clock multiplication factor N. + * + * @note This function must be used only when the PLLSAI2 is disabled. + * @note PLLSAI2 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI2N__: specifies the multiplication factor for PLLSAI2 VCO output clock. + * This parameter must be a number between 8 and 86. + * @note You have to set the PLLSAI2N parameter correctly to ensure that the VCO + * output frequency is between 64 and 344 MHz. + * PLLSAI1 clock frequency = f(PLLSAI1) multiplied by PLLSAI2N + * + * @retval None + */ +#define __HAL_RCC_PLLSAI2_MULN_CONFIG(__PLLSAI2N__) \ + MODIFY_REG(RCC->PLLSAI2CFGR, RCC_PLLSAI2CFGR_PLLSAI2N, (__PLLSAI2N__) << 8U) + +/** @brief Macro to configure the PLLSAI2 clock division factor P. + * + * @note This function must be used only when the PLLSAI2 is disabled. + * @note PLLSAI2 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI2P__: specifies the division factor. + * This parameter must be a number in the range (7 or 17). + * Use to set SAI2 clock frequency = f(PLLSAI2) / __PLLSAI2P__ + * + * @retval None + */ +#define __HAL_RCC_PLLSAI2_DIVP_CONFIG(__PLLSAI2P__) \ + MODIFY_REG(RCC->PLLSAI2CFGR, RCC_PLLSAI2CFGR_PLLSAI2P, ((__PLLSAI2P__) >> 4U) << 17U) + +/** @brief Macro to configure the PLLSAI2 clock division factor R. + * + * @note This function must be used only when the PLLSAI2 is disabled. + * @note PLLSAI1 clock source is common with the main PLL (configured through + * __HAL_RCC_PLL_CONFIG() macro) + * + * @param __PLLSAI2R__: specifies the division factor. + * This parameter must be in the range (2, 4, 6 or 8). + * Use to set ADC clock frequency = f(PLLSAI2) / __PLLSAI2Q__ + * + * @retval None + */ +#define __HAL_RCC_PLLSAI2_DIVR_CONFIG(__PLLSAI2R__) \ + MODIFY_REG(RCC->PLLSAI2CFGR, RCC_PLLSAI2CFGR_PLLSAI2R, (((__PLLSAI2R__) >> 1U) - 1) << 25U) + +/** + * @brief Macros to enable or disable the PLLSAI2. + * @note The PLLSAI2 is disabled by hardware when entering STOP and STANDBY modes. + * @retval None + */ + +#define __HAL_RCC_PLLSAI2_ENABLE() SET_BIT(RCC->CR, RCC_CR_PLLSAI2ON) + +#define __HAL_RCC_PLLSAI2_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_PLLSAI2ON) + +/** + * @brief Macros to enable or disable each clock output (PLLSAI2_SAI2 and PLLSAI2_ADC2). + * @note Enabling and disabling those clocks can be done without the need to stop the PLL. + * This is mainly used to save Power. + * @param __PLLSAI2_CLOCKOUT__: specifies the PLLSAI2 clock to be output. + * This parameter can be one or a combination of the following values: + * @arg RCC_PLLSAI2_SAI2CLK: This clock is used to generate an accurate clock to achieve + * high-quality audio performance on SAI interface in case. + * @arg RCC_PLLSAI2_ADC2CLK: Clock used to clock ADC peripheral. + * @retval None + */ + +#define __HAL_RCC_PLLSAI2CLKOUT_ENABLE(__PLLSAI2_CLOCKOUT__) SET_BIT(RCC->PLLSAI2CFGR, (__PLLSAI2_CLOCKOUT__)) + +#define __HAL_RCC_PLLSAI2CLKOUT_DISABLE(__PLLSAI2_CLOCKOUT__) CLEAR_BIT(RCC->PLLSAI2CFGR, (__PLLSAI2_CLOCKOUT__)) + +/** + * @brief Macro to get clock output enable status (PLLSAI2_SAI2 and PLLSAI2_ADC2). + * @param __PLLSAI2_CLOCKOUT__: specifies the PLLSAI2 clock to be output. + * This parameter can be one of the following values: + * @arg RCC_PLLSAI2_SAI2CLK: This clock is used to generate an accurate clock to achieve + * high-quality audio performance on SAI interface in case. + * @arg RCC_PLLSAI2_ADC2CLK: Clock used to clock ADC peripheral. + * @retval SET / RESET + */ +#define __HAL_RCC_GET_PLLSAI2CLKOUT_CONFIG(__PLLSAI2_CLOCKOUT__) READ_BIT(RCC->PLLSAI2CFGR, (__PLLSAI2_CLOCKOUT__)) + +/** + * @brief Macro to configure the SAI1 clock source. + * @param __SAI1_CLKSOURCE__: defines the SAI1 clock source. This clock is derived + * from the PLLSAI1, system PLL or external clock (through a dedicated pin). + * This parameter can be one of the following values: + * @arg RCC_SAI1CLKSOURCE_PLLSAI1: SAI1 clock = PLLSAI1 "P" clock (PLLSAI1CLK) + * @arg RCC_SAI1CLKSOURCE_PLLSAI2: SAI1 clock = PLLSAI2 "P" clock (PLLSAI2CLK) + * @arg RCC_SAI1CLKSOURCE_PLL: SAI1 clock = PLL "P" clock (PLLSAI3CLK) + * @arg RCC_SAI1CLKSOURCE_PIN: SAI1 clock = External Clock (SAI1_EXTCLK) + * @retval None + */ +#define __HAL_RCC_SAI1_CONFIG(__SAI1_CLKSOURCE__)\ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_SAI1SEL, (uint32_t)(__SAI1_CLKSOURCE__)) + +/** @brief Macro to get the SAI1 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_SAI1CLKSOURCE_PLLSAI1: SAI1 clock = PLLSAI1 "P" clock (PLLSAI1CLK) + * @arg RCC_SAI1CLKSOURCE_PLLSAI2: SAI1 clock = PLLSAI2 "P" clock (PLLSAI2CLK) + * @arg RCC_SAI1CLKSOURCE_PLL: SAI1 clock = PLL "P" clock (PLLSAI3CLK) + * @arg RCC_SAI1CLKSOURCE_PIN: SAI1 clock = External Clock (SAI1_EXTCLK) + */ +#define __HAL_RCC_GET_SAI1_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_SAI1SEL))) + +/** + * @brief Macro to configure the SAI2 clock source. + * @param __SAI2_CLKSOURCE__: defines the SAI2 clock source. This clock is derived + * from the PLLSAI2, system PLL or external clock (through a dedicated pin). + * This parameter can be one of the following values: + * @arg RCC_SAI2CLKSOURCE_PLLSAI1: SAI2 clock = PLLSAI1 "P" clock (PLLSAI1CLK) + * @arg RCC_SAI2CLKSOURCE_PLLSAI2: SAI2 clock = PLLSAI2 "P" clock (PLLSAI2CLK) + * @arg RCC_SAI2CLKSOURCE_PLL: SAI2 clock = PLL "P" clock (PLLSAI3CLK) + * @arg RCC_SAI2CLKSOURCE_PIN: SAI2 clock = External Clock (SAI2_EXTCLK) + * @retval None + */ +#define __HAL_RCC_SAI2_CONFIG(__SAI2_CLKSOURCE__ )\ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_SAI2SEL, (uint32_t)(__SAI2_CLKSOURCE__)) + +/** @brief Macro to get the SAI2 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_SAI2CLKSOURCE_PLLSAI1: SAI2 clock = PLLSAI1 "P" clock (PLLSAI1CLK) + * @arg RCC_SAI2CLKSOURCE_PLLSAI2: SAI2 clock = PLLSAI2 "P" clock (PLLSAI2CLK) + * @arg RCC_SAI2CLKSOURCE_PLL: SAI2 clock = PLL "P" clock (PLLSAI3CLK) + * @arg RCC_SAI2CLKSOURCE_PIN: SAI2 clock = External Clock (SAI2_EXTCLK) + */ +#define __HAL_RCC_GET_SAI2_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_SAI2SEL))) + +/** @brief Macro to configure the I2C1 clock (I2C1CLK). + * + * @param __I2C1_CLKSOURCE__: specifies the I2C1 clock source. + * This parameter can be one of the following values: + * @arg RCC_I2C1CLKSOURCE_PCLK1: PCLK1 selected as I2C1 clock + * @arg RCC_I2C1CLKSOURCE_HSI: HSI selected as I2C1 clock + * @arg RCC_I2C1CLKSOURCE_SYSCLK: System Clock selected as I2C1 clock + * @retval None + */ +#define __HAL_RCC_I2C1_CONFIG(__I2C1_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_I2C1SEL, (uint32_t)(__I2C1_CLKSOURCE__)) + +/** @brief Macro to get the I2C1 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_I2C1CLKSOURCE_PCLK1: PCLK1 selected as I2C1 clock + * @arg RCC_I2C1CLKSOURCE_HSI: HSI selected as I2C1 clock + * @arg RCC_I2C1CLKSOURCE_SYSCLK: System Clock selected as I2C1 clock + */ +#define __HAL_RCC_GET_I2C1_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_I2C1SEL))) + +/** @brief Macro to configure the I2C2 clock (I2C2CLK). + * + * @param __I2C2_CLKSOURCE__: specifies the I2C2 clock source. + * This parameter can be one of the following values: + * @arg RCC_I2C2CLKSOURCE_PCLK1: PCLK1 selected as I2C2 clock + * @arg RCC_I2C2CLKSOURCE_HSI: HSI selected as I2C2 clock + * @arg RCC_I2C2CLKSOURCE_SYSCLK: System Clock selected as I2C2 clock + * @retval None + */ +#define __HAL_RCC_I2C2_CONFIG(__I2C2_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_I2C2SEL, (uint32_t)(__I2C2_CLKSOURCE__)) + +/** @brief Macro to get the I2C2 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_I2C2CLKSOURCE_PCLK1: PCLK1 selected as I2C2 clock + * @arg RCC_I2C2CLKSOURCE_HSI: HSI selected as I2C2 clock + * @arg RCC_I2C2CLKSOURCE_SYSCLK: System Clock selected as I2C2 clock + */ +#define __HAL_RCC_GET_I2C2_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_I2C2SEL))) + +/** @brief Macro to configure the I2C3 clock (I2C3CLK). + * + * @param __I2C3_CLKSOURCE__: specifies the I2C3 clock source. + * This parameter can be one of the following values: + * @arg RCC_I2C3CLKSOURCE_PCLK1: PCLK1 selected as I2C3 clock + * @arg RCC_I2C3CLKSOURCE_HSI: HSI selected as I2C3 clock + * @arg RCC_I2C3CLKSOURCE_SYSCLK: System Clock selected as I2C3 clock + * @retval None + */ +#define __HAL_RCC_I2C3_CONFIG(__I2C3_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_I2C3SEL, (uint32_t)(__I2C3_CLKSOURCE__)) + +/** @brief Macro to get the I2C3 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_I2C3CLKSOURCE_PCLK1: PCLK1 selected as I2C3 clock + * @arg RCC_I2C3CLKSOURCE_HSI: HSI selected as I2C3 clock + * @arg RCC_I2C3CLKSOURCE_SYSCLK: System Clock selected as I2C3 clock + */ +#define __HAL_RCC_GET_I2C3_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_I2C3SEL))) + +/** @brief Macro to configure the USART1 clock (USART1CLK). + * + * @param __USART1_CLKSOURCE__: specifies the USART1 clock source. + * This parameter can be one of the following values: + * @arg RCC_USART1CLKSOURCE_PCLK2: PCLK2 selected as USART1 clock + * @arg RCC_USART1CLKSOURCE_HSI: HSI selected as USART1 clock + * @arg RCC_USART1CLKSOURCE_SYSCLK: System Clock selected as USART1 clock + * @arg RCC_USART1CLKSOURCE_LSE: LSE selected as USART1 clock + * @retval None + */ +#define __HAL_RCC_USART1_CONFIG(__USART1_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_USART1SEL, (uint32_t)(__USART1_CLKSOURCE__)) + +/** @brief Macro to get the USART1 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_USART1CLKSOURCE_PCLK2: PCLK2 selected as USART1 clock + * @arg RCC_USART1CLKSOURCE_HSI: HSI selected as USART1 clock + * @arg RCC_USART1CLKSOURCE_SYSCLK: System Clock selected as USART1 clock + * @arg RCC_USART1CLKSOURCE_LSE: LSE selected as USART1 clock + */ +#define __HAL_RCC_GET_USART1_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_USART1SEL))) + +/** @brief Macro to configure the USART2 clock (USART2CLK). + * + * @param __USART2_CLKSOURCE__: specifies the USART2 clock source. + * This parameter can be one of the following values: + * @arg RCC_USART2CLKSOURCE_PCLK1: PCLK1 selected as USART2 clock + * @arg RCC_USART2CLKSOURCE_HSI: HSI selected as USART2 clock + * @arg RCC_USART2CLKSOURCE_SYSCLK: System Clock selected as USART2 clock + * @arg RCC_USART2CLKSOURCE_LSE: LSE selected as USART2 clock + * @retval None + */ +#define __HAL_RCC_USART2_CONFIG(__USART2_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_USART2SEL, (uint32_t)(__USART2_CLKSOURCE__)) + +/** @brief Macro to get the USART2 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_USART2CLKSOURCE_PCLK1: PCLK1 selected as USART2 clock + * @arg RCC_USART2CLKSOURCE_HSI: HSI selected as USART2 clock + * @arg RCC_USART2CLKSOURCE_SYSCLK: System Clock selected as USART2 clock + * @arg RCC_USART2CLKSOURCE_LSE: LSE selected as USART2 clock + */ +#define __HAL_RCC_GET_USART2_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_USART2SEL))) + +/** @brief Macro to configure the USART3 clock (USART3CLK). + * + * @param __USART3_CLKSOURCE__: specifies the USART3 clock source. + * This parameter can be one of the following values: + * @arg RCC_USART3CLKSOURCE_PCLK1: PCLK1 selected as USART3 clock + * @arg RCC_USART3CLKSOURCE_HSI: HSI selected as USART3 clock + * @arg RCC_USART3CLKSOURCE_SYSCLK: System Clock selected as USART3 clock + * @arg RCC_USART3CLKSOURCE_LSE: LSE selected as USART3 clock + * @retval None + */ +#define __HAL_RCC_USART3_CONFIG(__USART3_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_USART3SEL, (uint32_t)(__USART3_CLKSOURCE__)) + +/** @brief Macro to get the USART3 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_USART3CLKSOURCE_PCLK1: PCLK1 selected as USART3 clock + * @arg RCC_USART3CLKSOURCE_HSI: HSI selected as USART3 clock + * @arg RCC_USART3CLKSOURCE_SYSCLK: System Clock selected as USART3 clock + * @arg RCC_USART3CLKSOURCE_LSE: LSE selected as USART3 clock + */ +#define __HAL_RCC_GET_USART3_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_USART3SEL))) + + /** @brief Macro to configure the UART4 clock (UART4CLK). + * + * @param __UART4_CLKSOURCE__: specifies the UART4 clock source. + * This parameter can be one of the following values: + * @arg RCC_UART4CLKSOURCE_PCLK1: PCLK1 selected as UART4 clock + * @arg RCC_UART4CLKSOURCE_HSI: HSI selected as UART4 clock + * @arg RCC_UART4CLKSOURCE_SYSCLK: System Clock selected as UART4 clock + * @arg RCC_UART4CLKSOURCE_LSE: LSE selected as UART4 clock + * @retval None + */ +#define __HAL_RCC_UART4_CONFIG(__UART4_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_UART4SEL, (uint32_t)(__UART4_CLKSOURCE__)) + +/** @brief Macro to get the UART4 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_UART4CLKSOURCE_PCLK1: PCLK1 selected as UART4 clock + * @arg RCC_UART4CLKSOURCE_HSI: HSI selected as UART4 clock + * @arg RCC_UART4CLKSOURCE_SYSCLK: System Clock selected as UART4 clock + * @arg RCC_UART4CLKSOURCE_LSE: LSE selected as UART4 clock + */ +#define __HAL_RCC_GET_UART4_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_UART4SEL))) + + /** @brief Macro to configure the UART5 clock (UART5CLK). + * + * @param __UART5_CLKSOURCE__: specifies the UART5 clock source. + * This parameter can be one of the following values: + * @arg RCC_UART5CLKSOURCE_PCLK1: PCLK1 selected as UART5 clock + * @arg RCC_UART5CLKSOURCE_HSI: HSI selected as UART5 clock + * @arg RCC_UART5CLKSOURCE_SYSCLK: System Clock selected as UART5 clock + * @arg RCC_UART5CLKSOURCE_LSE: LSE selected as UART5 clock + * @retval None + */ +#define __HAL_RCC_UART5_CONFIG(__UART5_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_UART5SEL, (uint32_t)(__UART5_CLKSOURCE__)) + +/** @brief Macro to get the UART5 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_UART5CLKSOURCE_PCLK1: PCLK1 selected as UART5 clock + * @arg RCC_UART5CLKSOURCE_HSI: HSI selected as UART5 clock + * @arg RCC_UART5CLKSOURCE_SYSCLK: System Clock selected as UART5 clock + * @arg RCC_UART5CLKSOURCE_LSE: LSE selected as UART5 clock + */ +#define __HAL_RCC_GET_UART5_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_UART5SEL))) + +/** @brief Macro to configure the LPUART1 clock (LPUART1CLK). + * + * @param __LPUART1_CLKSOURCE__: specifies the LPUART1 clock source. + * This parameter can be one of the following values: + * @arg RCC_LPUART1CLKSOURCE_PCLK1: PCLK1 selected as LPUART1 clock + * @arg RCC_LPUART1CLKSOURCE_HSI: HSI selected as LPUART1 clock + * @arg RCC_LPUART1CLKSOURCE_SYSCLK: System Clock selected as LPUART1 clock + * @arg RCC_LPUART1CLKSOURCE_LSE: LSE selected as LPUART1 clock + * @retval None + */ +#define __HAL_RCC_LPUART1_CONFIG(__LPUART1_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_LPUART1SEL, (uint32_t)(__LPUART1_CLKSOURCE__)) + +/** @brief Macro to get the LPUART1 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_LPUART1CLKSOURCE_PCLK1: PCLK1 selected as LPUART1 clock + * @arg RCC_LPUART1CLKSOURCE_HSI: HSI selected as LPUART1 clock + * @arg RCC_LPUART1CLKSOURCE_SYSCLK: System Clock selected as LPUART1 clock + * @arg RCC_LPUART1CLKSOURCE_LSE: LSE selected as LPUART1 clock + */ +#define __HAL_RCC_GET_LPUART1_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_LPUART1SEL))) + +/** @brief Macro to configure the LPTIM1 clock (LPTIM1CLK). + * + * @param __LPTIM1_CLKSOURCE__: specifies the LPTIM1 clock source. + * This parameter can be one of the following values: + * @arg RCC_LPTIM1CLKSOURCE_PCLK: PCLK selected as LPTIM1 clock + * @arg RCC_LPTIM1CLKSOURCE_LSI : HSI selected as LPTIM1 clock + * @arg RCC_LPTIM1CLKSOURCE_HSI : LSI selected as LPTIM1 clock + * @arg RCC_LPTIM1CLKSOURCE_LSE : LSE selected as LPTIM1 clock + * @retval None + */ +#define __HAL_RCC_LPTIM1_CONFIG(__LPTIM1_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_LPTIM1SEL, (uint32_t)(__LPTIM1_CLKSOURCE__)) + +/** @brief Macro to get the LPTIM1 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_LPTIM1CLKSOURCE_PCLK: PCLK selected as LPUART1 clock + * @arg RCC_LPTIM1CLKSOURCE_LSI : HSI selected as LPUART1 clock + * @arg RCC_LPTIM1CLKSOURCE_HSI : System Clock selected as LPUART1 clock + * @arg RCC_LPTIM1CLKSOURCE_LSE : LSE selected as LPUART1 clock + */ +#define __HAL_RCC_GET_LPTIM1_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_LPTIM1SEL))) + +/** @brief Macro to configure the LPTIM2 clock (LPTIM2CLK). + * + * @param __LPTIM2_CLKSOURCE__: specifies the LPTIM2 clock source. + * This parameter can be one of the following values: + * @arg RCC_LPTIM2CLKSOURCE_PCLK: PCLK selected as LPTIM2 clock + * @arg RCC_LPTIM2CLKSOURCE_LSI : HSI selected as LPTIM2 clock + * @arg RCC_LPTIM2CLKSOURCE_HSI : LSI selected as LPTIM2 clock + * @arg RCC_LPTIM2CLKSOURCE_LSE : LSE selected as LPTIM2 clock + * @retval None + */ +#define __HAL_RCC_LPTIM2_CONFIG(__LPTIM2_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_LPTIM2SEL, (uint32_t)(__LPTIM2_CLKSOURCE__)) + +/** @brief Macro to get the LPTIM2 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_LPTIM2CLKSOURCE_PCLK: PCLK selected as LPUART1 clock + * @arg RCC_LPTIM2CLKSOURCE_LSI : HSI selected as LPUART1 clock + * @arg RCC_LPTIM2CLKSOURCE_HSI : System Clock selected as LPUART1 clock + * @arg RCC_LPTIM2CLKSOURCE_LSE : LSE selected as LPUART1 clock + */ +#define __HAL_RCC_GET_LPTIM2_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_LPTIM2SEL))) + +/** @brief Macro to configure the SDMMC1 clock. + * + * @note USB, RNG and SDMMC1 peripherals share the same 48MHz clock source. + * + * @param __SDMMC1_CLKSOURCE__: specifies the SDMMC1 clock source. + * This parameter can be one of the following values: + * @arg RCC_SDMMC1CLKSOURCE_NONE: No clock selected as SDMMC1 clock + * @arg RCC_SDMMC1CLKSOURCE_MSI: MSI selected as SDMMC1 clock + * @arg RCC_SDMMC1CLKSOURCE_PLLSAI1: PLLSAI1 Clock selected as SDMMC1 clock + * @arg RCC_SDMMC1CLKSOURCE_PLL: PLL Clock selected as SDMMC1 clock + * @retval None + */ +#define __HAL_RCC_SDMMC1_CONFIG(__SDMMC1_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_CLK48SEL, (uint32_t)(__SDMMC1_CLKSOURCE__)) + +/** @brief Macro to get the SDMMC1 clock. + * @retval The clock source can be one of the following values: + * @arg RCC_SDMMC1CLKSOURCE_NONE: No clock selected as SDMMC1 clock + * @arg RCC_SDMMC1CLKSOURCE_MSI: MSI selected as SDMMC1 clock + * @arg RCC_SDMMC1CLKSOURCE_PLLSAI1: PLLSAI1 "Q" clock (PLL48M2CLK) selected as SDMMC1 clock + * @arg RCC_SDMMC1CLKSOURCE_PLL: PLL "Q" clock (PLL48M1CLK) selected as SDMMC1 clock + */ +#define __HAL_RCC_GET_SDMMC1_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_CLK48SEL))) + +/** @brief Macro to configure the RNG clock. + * + * @note USB, RNG and SDMMC1 peripherals share the same 48MHz clock source. + * + * @param __RNG_CLKSOURCE__: specifies the RNG clock source. + * This parameter can be one of the following values: + * @arg RCC_RNGCLKSOURCE_NONE: No clock selected as RNG clock + * @arg RCC_RNGCLKSOURCE_MSI: MSI selected as RNG clock + * @arg RCC_RNGCLKSOURCE_PLLSAI1: PLLSAI1 Clock selected as RNG clock + * @arg RCC_RNGCLKSOURCE_PLL: PLL Clock selected as RNG clock + * @retval None + */ +#define __HAL_RCC_RNG_CONFIG(__RNG_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_CLK48SEL, (uint32_t)(__RNG_CLKSOURCE__)) + +/** @brief Macro to get the RNG clock. + * @retval The clock source can be one of the following values: + * @arg RCC_RNGCLKSOURCE_NONE: No clock selected as RNG clock + * @arg RCC_RNGCLKSOURCE_MSI: MSI selected as RNG clock + * @arg RCC_RNGCLKSOURCE_PLLSAI1: PLLSAI1 "Q" clock (PLL48M2CLK) selected as RNG clock + * @arg RCC_RNGCLKSOURCE_PLL: PLL "Q" clock (PLL48M1CLK) selected as RNG clock + */ +#define __HAL_RCC_GET_RNG_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_CLK48SEL))) + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +/** @brief Macro to configure the USB clock (USBCLK). + * + * @note USB, RNG and SDMMC1 peripherals share the same 48MHz clock source. + * + * @param __USB_CLKSOURCE__: specifies the USB clock source. + * This parameter can be one of the following values: + * @arg RCC_USBCLKSOURCE_NONE: No clock selected as 48MHz clock + * @arg RCC_USBCLKSOURCE_MSI: MSI selected as USB clock + * @arg RCC_USBCLKSOURCE_PLLSAI1: PLLSAI1 "Q" clock (PLL48M2CLK) selected as USB clock + * @arg RCC_USBCLKSOURCE_PLL: PLL "Q" clock (PLL48M1CLK) selected as USB clock + * @retval None + */ +#define __HAL_RCC_USB_CONFIG(__USB_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_CLK48SEL, (uint32_t)(__USB_CLKSOURCE__)) + +/** @brief Macro to get the USB clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_USBCLKSOURCE_NONE: No clock selected as 48MHz clock + * @arg RCC_USBCLKSOURCE_MSI: MSI selected as USB clock + * @arg RCC_USBCLKSOURCE_PLLSAI1: PLLSAI1 "Q" clock (PLL48M2CLK) selected as USB clock + * @arg RCC_USBCLKSOURCE_PLL: PLL "Q" clock (PLL48M1CLK) selected as USB clock + */ +#define __HAL_RCC_GET_USB_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_CLK48SEL))) + +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + +/** @brief Macro to configure the ADC interface clock. + * @param __ADC_CLKSOURCE__: specifies the ADC digital interface clock source. + * This parameter can be one of the following values: + * @arg RCC_ADCCLKSOURCE_PLLSAI1: PLLSAI1 Clock selected as ADC clock + * @arg RCC_ADCCLKSOURCE_PLLSAI2: PLLSAI2 Clock selected as ADC clock + * @arg RCC_ADCCLKSOURCE_SYSCLK: System Clock selected as ADC clock + * @retval None + */ +#define __HAL_RCC_ADC_CONFIG(__ADC_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_ADCSEL, (uint32_t)(__ADC_CLKSOURCE__)) + +/** @brief Macro to get the ADC clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_ADCCLKSOURCE_PLLSAI1: PLLSAI1 Clock selected as ADC clock + * @arg RCC_ADCCLKSOURCE_PLLSAI2: PLLSAI2 Clock selected as ADC clock + * @arg RCC_ADCCLKSOURCE_SYSCLK: System Clock selected as ADC clock + */ +#define __HAL_RCC_GET_ADC_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_ADCSEL))) + + /** @brief Macro to configure the SWPMI1 clock. + * @param __SWPMI1_CLKSOURCE__: specifies the SWPMI1 clock source. + * This parameter can be one of the following values: + * @arg RCC_SWPMI1CLKSOURCE_PCLK: PCLK Clock selected as SWPMI1 clock + * @arg RCC_SWPMI1CLKSOURCE_HSI: HSI Clock selected as SWPMI1 clock + * @retval None + */ +#define __HAL_RCC_SWPMI1_CONFIG(__SWPMI1_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_SWPMI1SEL, (uint32_t)(__SWPMI1_CLKSOURCE__)) + +/** @brief Macro to get the SWPMI1 clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_SWPMI1CLKSOURCE_PCLK: PCLK Clock selected as SWPMI1 clock + * @arg RCC_SWPMI1CLKSOURCE_HSI: HSI Clock selected as SWPMI1 clock + */ +#define __HAL_RCC_GET_SWPMI1_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_SWPMI1SEL))) + + /** @brief Macro to configure the DFSDM clock. + * @param __DFSDM_CLKSOURCE__: specifies the DFSDM clock source. + * This parameter can be one of the following values: + * @arg RCC_DFSDMCLKSOURCE_PCLK: PCLK Clock selected as DFSDM clock + * @arg RCC_DFSDMCLKSOURCE_HSI: HSI Clock selected as DFSDM clock + * @retval None + */ +#define __HAL_RCC_DFSDM_CONFIG(__DFSDM_CLKSOURCE__) \ + MODIFY_REG(RCC->CCIPR, RCC_CCIPR_DFSDMSEL, (uint32_t)(__DFSDM_CLKSOURCE__)) + +/** @brief Macro to get the DFSDM clock source. + * @retval The clock source can be one of the following values: + * @arg RCC_DFSDMCLKSOURCE_PCLK: PCLK Clock selected as DFSDM clock + * @arg RCC_DFSDMCLKSOURCE_HSI: HSI Clock selected as DFSDM clock + */ +#define __HAL_RCC_GET_DFSDM_SOURCE() ((uint32_t)(READ_BIT(RCC->CCIPR, RCC_CCIPR_DFSDMSEL))) + + +/** @defgroup RCCEx_Flags_Interrupts_Management Flags Interrupts Management + * @brief macros to manage the specified RCC Flags and interrupts. + * @{ + */ + +/** @brief Enable PLLSAI1RDY interrupt. + * @retval None + */ +#define __HAL_RCC_PLLSAI1_ENABLE_IT() SET_BIT(RCC->CIER, RCC_CIER_PLLSAI1RDYIE) + +/** @brief Disable PLLSAI1RDY interrupt. + * @retval None + */ +#define __HAL_RCC_PLLSAI1_DISABLE_IT() CLEAR_BIT(RCC->CIER, RCC_CIER_PLLSAI1RDYIE) + +/** @brief Clear the PLLSAI1RDY interrupt pending bit. + * @retval None + */ +#define __HAL_RCC_PLLSAI1_CLEAR_IT() WRITE_REG(RCC->CICR, RCC_CICR_PLLSAI1RDYC) + +/** @brief Check whether PLLSAI1RDY interrupt has occurred or not. + * @retval TRUE or FALSE. + */ +#define __HAL_RCC_PLLSAI1_GET_IT_SOURCE() (READ_BIT(RCC->CIFR, RCC_CIFR_PLLSAI1RDYF) == RCC_CIFR_PLLSAI1RDYF) + +/** @brief Check whether the PLLSAI1RDY flag is set or not. + * @retval TRUE or FALSE. + */ +#define __HAL_RCC_PLLSAI1_GET_FLAG() (READ_BIT(RCC->CR, RCC_CR_PLLSAI1RDY) == (RCC_CR_PLLSAI1RDY)) + +/** @brief Enable PLLSAI2RDY interrupt. + * @retval None + */ +#define __HAL_RCC_PLLSAI2_ENABLE_IT() SET_BIT(RCC->CIER, RCC_CIER_PLLSAI2RDYIE) + +/** @brief Disable PLLSAI2RDY interrupt. + * @retval None + */ +#define __HAL_RCC_PLLSAI2_DISABLE_IT() CLEAR_BIT(RCC->CIER, RCC_CIER_PLLSAI2RDYIE) + +/** @brief Clear the PLLSAI2RDY interrupt pending bit. + * @retval None + */ +#define __HAL_RCC_PLLSAI2_CLEAR_IT() WRITE_REG(RCC->CICR, RCC_CICR_PLLSAI2RDYC) + +/** @brief Check whether the PLLSAI2RDY interrupt has occurred or not. + * @retval TRUE or FALSE. + */ +#define __HAL_RCC_PLLSAI2_GET_IT_SOURCE() (READ_BIT(RCC->CIFR, RCC_CIFR_PLLSAI2RDYF) == RCC_CIFR_PLLSAI2RDYF) + +/** @brief Check whether the PLLSAI2RDY flag is set or not. + * @retval TRUE or FALSE. + */ +#define __HAL_RCC_PLLSAI2_GET_FLAG() (READ_BIT(RCC->CR, RCC_CR_PLLSAI2RDY) == (RCC_CR_PLLSAI2RDY)) + +/** + * @} + */ + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup RCCEx_Exported_Functions + * @{ + */ + +/** @addtogroup RCCEx_Exported_Functions_Group1 + * @{ + */ + +HAL_StatusTypeDef HAL_RCCEx_PeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit); +void HAL_RCCEx_GetPeriphCLKConfig(RCC_PeriphCLKInitTypeDef *PeriphClkInit); +uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk); + +/** + * @} + */ + +/** @addtogroup RCCEx_Exported_Functions_Group2 + * @{ + */ + +HAL_StatusTypeDef HAL_RCCEx_EnablePLLSAI1(RCC_PLLSAI1InitTypeDef *PLLSAI1Init); +HAL_StatusTypeDef HAL_RCCEx_DisablePLLSAI1(void); +HAL_StatusTypeDef HAL_RCCEx_EnablePLLSAI2(RCC_PLLSAI2InitTypeDef *PLLSAI2Init); +HAL_StatusTypeDef HAL_RCCEx_DisablePLLSAI2(void); +void HAL_RCCEx_WakeUpStopCLKConfig(uint32_t WakeUpClk); +void HAL_RCCEx_StandbyMSIRangeConfig(uint32_t MSIRange); +void HAL_RCCEx_EnableLSECSS(void); +void HAL_RCCEx_DisableLSECSS(void); +void HAL_RCCEx_EnableLSCO(uint32_t LSCOSource); +void HAL_RCCEx_DisableLSCO(void); +void HAL_RCCEx_EnableMSIPLLMode(void); +void HAL_RCCEx_DisableMSIPLLMode(void); + +/** + * @} + */ + +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @addtogroup RCCEx_Private_Macros + * @{ + */ + +#define IS_RCC_LSCOSOURCE(__SOURCE__) (((__SOURCE__) == RCC_LSCOSOURCE_LSI) || \ + ((__SOURCE__) == RCC_LSCOSOURCE_LSE)) + +#if defined(STM32L471xx) + +#define IS_RCC_PERIPHCLOCK(__SELECTION__) \ + ((((__SELECTION__) & RCC_PERIPHCLK_USART1) == RCC_PERIPHCLK_USART1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USART2) == RCC_PERIPHCLK_USART2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USART3) == RCC_PERIPHCLK_USART3) || \ + (((__SELECTION__) & RCC_PERIPHCLK_UART4) == RCC_PERIPHCLK_UART4) || \ + (((__SELECTION__) & RCC_PERIPHCLK_UART5) == RCC_PERIPHCLK_UART5) || \ + (((__SELECTION__) & RCC_PERIPHCLK_LPUART1) == RCC_PERIPHCLK_LPUART1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2C1) == RCC_PERIPHCLK_I2C1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2C2) == RCC_PERIPHCLK_I2C2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2C3) == RCC_PERIPHCLK_I2C3) || \ + (((__SELECTION__) & RCC_PERIPHCLK_LPTIM1) == RCC_PERIPHCLK_LPTIM1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_LPTIM2) == RCC_PERIPHCLK_LPTIM2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SWPMI1) == RCC_PERIPHCLK_SWPMI1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_DFSDM) == RCC_PERIPHCLK_DFSDM) || \ + (((__SELECTION__) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_RNG) == RCC_PERIPHCLK_RNG) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SDMMC1) == RCC_PERIPHCLK_SDMMC1)) + +#else /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + +#define IS_RCC_PERIPHCLOCK(__SELECTION__) \ + ((((__SELECTION__) & RCC_PERIPHCLK_USART1) == RCC_PERIPHCLK_USART1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USART2) == RCC_PERIPHCLK_USART2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USART3) == RCC_PERIPHCLK_USART3) || \ + (((__SELECTION__) & RCC_PERIPHCLK_UART4) == RCC_PERIPHCLK_UART4) || \ + (((__SELECTION__) & RCC_PERIPHCLK_UART5) == RCC_PERIPHCLK_UART5) || \ + (((__SELECTION__) & RCC_PERIPHCLK_LPUART1) == RCC_PERIPHCLK_LPUART1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2C1) == RCC_PERIPHCLK_I2C1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2C2) == RCC_PERIPHCLK_I2C2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_I2C3) == RCC_PERIPHCLK_I2C3) || \ + (((__SELECTION__) & RCC_PERIPHCLK_LPTIM1) == RCC_PERIPHCLK_LPTIM1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_LPTIM2) == RCC_PERIPHCLK_LPTIM2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SAI1) == RCC_PERIPHCLK_SAI1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SAI2) == RCC_PERIPHCLK_SAI2) || \ + (((__SELECTION__) & RCC_PERIPHCLK_USB) == RCC_PERIPHCLK_USB) || \ + (((__SELECTION__) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SWPMI1) == RCC_PERIPHCLK_SWPMI1) || \ + (((__SELECTION__) & RCC_PERIPHCLK_DFSDM) == RCC_PERIPHCLK_DFSDM) || \ + (((__SELECTION__) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC) || \ + (((__SELECTION__) & RCC_PERIPHCLK_RNG) == RCC_PERIPHCLK_RNG) || \ + (((__SELECTION__) & RCC_PERIPHCLK_SDMMC1) == RCC_PERIPHCLK_SDMMC1)) + +#endif /* STM32L471xx */ + +#define IS_RCC_USART1CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_USART1CLKSOURCE_PCLK2) || \ + ((__SOURCE__) == RCC_USART1CLKSOURCE_SYSCLK) || \ + ((__SOURCE__) == RCC_USART1CLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_USART1CLKSOURCE_HSI)) + +#define IS_RCC_USART2CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_USART2CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_USART2CLKSOURCE_SYSCLK) || \ + ((__SOURCE__) == RCC_USART2CLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_USART2CLKSOURCE_HSI)) + +#define IS_RCC_USART3CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_USART3CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_USART3CLKSOURCE_SYSCLK) || \ + ((__SOURCE__) == RCC_USART3CLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_USART3CLKSOURCE_HSI)) + +#define IS_RCC_UART4CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_UART4CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_UART4CLKSOURCE_SYSCLK) || \ + ((__SOURCE__) == RCC_UART4CLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_UART4CLKSOURCE_HSI)) + +#define IS_RCC_UART5CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_UART5CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_UART5CLKSOURCE_SYSCLK) || \ + ((__SOURCE__) == RCC_UART5CLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_UART5CLKSOURCE_HSI)) + +#define IS_RCC_LPUART1CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_LPUART1CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_LPUART1CLKSOURCE_SYSCLK) || \ + ((__SOURCE__) == RCC_LPUART1CLKSOURCE_LSE) || \ + ((__SOURCE__) == RCC_LPUART1CLKSOURCE_HSI)) + +#define IS_RCC_I2C1CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_I2C1CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_I2C1CLKSOURCE_SYSCLK)|| \ + ((__SOURCE__) == RCC_I2C1CLKSOURCE_HSI)) + +#define IS_RCC_I2C2CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_I2C2CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_I2C2CLKSOURCE_SYSCLK)|| \ + ((__SOURCE__) == RCC_I2C2CLKSOURCE_HSI)) + +#define IS_RCC_I2C3CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_I2C3CLKSOURCE_PCLK1) || \ + ((__SOURCE__) == RCC_I2C3CLKSOURCE_SYSCLK)|| \ + ((__SOURCE__) == RCC_I2C3CLKSOURCE_HSI)) + +#define IS_RCC_SAI1CLK(__SOURCE__) \ + (((__SOURCE__) == RCC_SAI1CLKSOURCE_PLLSAI1) || \ + ((__SOURCE__) == RCC_SAI1CLKSOURCE_PLLSAI2) || \ + ((__SOURCE__) == RCC_SAI1CLKSOURCE_PLL) || \ + ((__SOURCE__) == RCC_SAI1CLKSOURCE_PIN)) + +#define IS_RCC_SAI2CLK(__SOURCE__) \ + (((__SOURCE__) == RCC_SAI2CLKSOURCE_PLLSAI2) || \ + ((__SOURCE__) == RCC_SAI2CLKSOURCE_PLLSAI2) || \ + ((__SOURCE__) == RCC_SAI2CLKSOURCE_PLL) || \ + ((__SOURCE__) == RCC_SAI2CLKSOURCE_PIN)) + +#define IS_RCC_LPTIM1CLK(__SOURCE__) \ + (((__SOURCE__) == RCC_LPTIM1CLKSOURCE_PCLK) || \ + ((__SOURCE__) == RCC_LPTIM1CLKSOURCE_LSI) || \ + ((__SOURCE__) == RCC_LPTIM1CLKSOURCE_HSI) || \ + ((__SOURCE__) == RCC_LPTIM1CLKSOURCE_LSE)) + +#define IS_RCC_LPTIM2CLK(__SOURCE__) \ + (((__SOURCE__) == RCC_LPTIM2CLKSOURCE_PCLK) || \ + ((__SOURCE__) == RCC_LPTIM2CLKSOURCE_LSI) || \ + ((__SOURCE__) == RCC_LPTIM2CLKSOURCE_HSI) || \ + ((__SOURCE__) == RCC_LPTIM2CLKSOURCE_LSE)) + +#define IS_RCC_SDMMC1CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_SDMMC1CLKSOURCE_NONE) || \ + ((__SOURCE__) == RCC_SDMMC1CLKSOURCE_PLLSAI1) || \ + ((__SOURCE__) == RCC_SDMMC1CLKSOURCE_PLL) || \ + ((__SOURCE__) == RCC_SDMMC1CLKSOURCE_MSI)) + +#define IS_RCC_RNGCLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_RNGCLKSOURCE_NONE) || \ + ((__SOURCE__) == RCC_RNGCLKSOURCE_PLLSAI1) || \ + ((__SOURCE__) == RCC_RNGCLKSOURCE_PLL) || \ + ((__SOURCE__) == RCC_RNGCLKSOURCE_MSI)) + +#if defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) +#define IS_RCC_USBCLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_USBCLKSOURCE_NONE) || \ + ((__SOURCE__) == RCC_USBCLKSOURCE_PLLSAI1) || \ + ((__SOURCE__) == RCC_USBCLKSOURCE_PLL) || \ + ((__SOURCE__) == RCC_USBCLKSOURCE_MSI)) +#endif /* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx */ + +#define IS_RCC_ADCCLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_ADCCLKSOURCE_NONE) || \ + ((__SOURCE__) == RCC_ADCCLKSOURCE_PLLSAI1) || \ + ((__SOURCE__) == RCC_ADCCLKSOURCE_PLLSAI2) || \ + ((__SOURCE__) == RCC_ADCCLKSOURCE_SYSCLK)) + +#define IS_RCC_SWPMI1CLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_SWPMI1CLKSOURCE_PCLK) || \ + ((__SOURCE__) == RCC_SWPMI1CLKSOURCE_HSI)) + +#define IS_RCC_DFSDMCLKSOURCE(__SOURCE__) \ + (((__SOURCE__) == RCC_DFSDMCLKSOURCE_PCLK) || \ + ((__SOURCE__) == RCC_DFSDMCLKSOURCE_SYSCLK)) + + +#define IS_RCC_PLLSAI1N_VALUE(__VALUE__) ((8 <= (__VALUE__)) && ((__VALUE__) <= 86)) + +#define IS_RCC_PLLSAI1P_VALUE(__VALUE__) (((__VALUE__) == 7) || ((__VALUE__) == 17)) + +#define IS_RCC_PLLSAI1Q_VALUE(__VALUE__) (((__VALUE__) == 2 ) || ((__VALUE__) == 4) || \ + ((__VALUE__) == 6) || ((__VALUE__) == 8)) + +#define IS_RCC_PLLSAI1R_VALUE(__VALUE__) (((__VALUE__) == 2 ) || ((__VALUE__) == 4) || \ + ((__VALUE__) == 6) || ((__VALUE__) == 8)) + +#define IS_RCC_PLLSAI2N_VALUE(__VALUE__) ((8 <= (__VALUE__)) && ((__VALUE__) <= 86)) + +#define IS_RCC_PLLSAI2P_VALUE(__VALUE__) (((__VALUE__) == 7) || ((__VALUE__) == 17)) + +#define IS_RCC_PLLSAI2R_VALUE(__VALUE__) (((__VALUE__) == 2 ) || ((__VALUE__) == 4) || \ + ((__VALUE__) == 6) || ((__VALUE__) == 8)) + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32L4xx_HAL_RCC_EX_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/