same
Fork of RF24 by
Diff: RF24.cpp
- Revision:
- 3:e94be00fd19e
- Parent:
- 2:3bdf0d9bb71f
- Child:
- 5:ee34c2837c4c
--- a/RF24.cpp Thu Nov 05 05:40:23 2015 +0000 +++ b/RF24.cpp Thu Nov 05 05:45:58 2015 +0000 @@ -6,6 +6,14 @@ version 2 as published by the Free Software Foundation. */ +/* + * Mbed support added by Akash Vibhute <akash.roboticist@gmail.com> + * Porting completed on Nov/05/2015 + * + * Updated with TMRh20's RF24 library on Nov/04/2015 from https://github.com/TMRh20 + * + */ + #include "nRF24L01.h" #include "RF24_config.h" #include "RF24.h" @@ -16,344 +24,168 @@ { csn_pin = mode; wait_us(5); - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - } /****************************************************************************/ void RF24::ce(bool level) { - ce_pin = level; - + ce_pin = level; } /****************************************************************************/ - inline void RF24::beginTransaction() { +inline void RF24::beginTransaction() +{ csn_pin=LOW; - - - - } +} /****************************************************************************/ - inline void RF24::endTransaction() { +inline void RF24::endTransaction() +{ csn_pin=HIGH; - - - - } +} /****************************************************************************/ uint8_t RF24::read_register(uint8_t reg, uint8_t* buf, uint8_t len) { - uint8_t status; - - beginTransaction(); - status = spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); - while ( len-- ) - *buf++ = spi.write(0xff); - endTransaction(); + uint8_t status; - - - - - - - - - - - - - - - - - - - - - - - return status; + beginTransaction(); + status = spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); + while ( len-- ) + *buf++ = spi.write(0xff); + endTransaction(); + + return status; } /****************************************************************************/ uint8_t RF24::read_register(uint8_t reg) { - uint8_t result; - - beginTransaction(); - spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); - result = spi.write(0xff); - endTransaction(); + uint8_t result; - - - - - - - - - - - - - - - - - return result; + beginTransaction(); + spi.write( R_REGISTER | ( REGISTER_MASK & reg ) ); + result = spi.write(0xff); + endTransaction(); + + return result; } /****************************************************************************/ uint8_t RF24::write_register(uint8_t reg, const uint8_t* buf, uint8_t len) { - uint8_t status; - - beginTransaction(); - status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); - while ( len-- ) - spi.write(*buf++); - endTransaction(); + uint8_t status; - - - - - - - - - - - - - - - - - - - return status; + beginTransaction(); + status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); + while ( len-- ) + spi.write(*buf++); + endTransaction(); + + return status; } /****************************************************************************/ uint8_t RF24::write_register(uint8_t reg, uint8_t value) { - uint8_t status; - - IF_SERIAL_DEBUG(printf(PSTR("write_register(%02x,%02x)\r\n"),reg,value)); - + uint8_t status; - beginTransaction(); - status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); - spi.write(value); - endTransaction(); - + IF_SERIAL_DEBUG(printf(PSTR("write_register(%02x,%02x)\r\n"),reg,value)); - - - - - - - - - - - - - return status; + beginTransaction(); + status = spi.write( W_REGISTER | ( REGISTER_MASK & reg ) ); + spi.write(value); + endTransaction(); + + return status; } /****************************************************************************/ uint8_t RF24::write_payload(const void* buf, uint8_t len, const uint8_t writeType) { - uint8_t status; - const uint8_t* current = reinterpret_cast<const uint8_t*>(buf); - - uint8_t data_len = rf24_min(data_len, payload_size); - uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len; - - //printf("[Writing %u bytes %u blanks]",data_len,blank_len); - IF_SERIAL_DEBUG( printf("[Writing %u bytes %u blanks]\n",data_len,blank_len); ); - + uint8_t status; + const uint8_t* current = reinterpret_cast<const uint8_t*>(buf); - beginTransaction(); - status = spi.write( W_TX_PAYLOAD ); - while ( data_len-- ) - spi.write(*current++); - while ( blank_len-- ) - spi.write(0); - - endTransaction(); + uint8_t data_len = rf24_min(data_len, payload_size); + uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len; - + IF_SERIAL_DEBUG( printf("[Writing %u bytes %u blanks]\n",data_len,blank_len); ); - - - - - - - - - - - - - - - - - - - - - return status; + beginTransaction(); + status = spi.write( W_TX_PAYLOAD ); + while ( data_len-- ) + spi.write(*current++); + while ( blank_len-- ) + spi.write(0); + + endTransaction(); + + return status; } /****************************************************************************/ uint8_t RF24::read_payload(void* buf, uint8_t data_len) { - uint8_t status; - uint8_t* current = reinterpret_cast<uint8_t*>(buf); - - if(data_len > payload_size) data_len = payload_size; - uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len; - - //printf("[Reading %u bytes %u blanks]",data_len,blank_len); + uint8_t status; + uint8_t* current = reinterpret_cast<uint8_t*>(buf); - IF_SERIAL_DEBUG( printf("[Reading %u bytes %u blanks]\n",data_len,blank_len); ); + if(data_len > payload_size) data_len = payload_size; + uint8_t blank_len = dynamic_payloads_enabled ? 0 : payload_size - data_len; - beginTransaction(); - status = spi.write( R_RX_PAYLOAD ); - while ( data_len-- ) - *current++ = spi.write(0xff); - while ( blank_len-- ) - spi.write(0xff); - endTransaction(); + IF_SERIAL_DEBUG( printf("[Reading %u bytes %u blanks]\n",data_len,blank_len); ); - - - - - - - - - - - - - - - - - - - - - - - - - - - - - return status; + beginTransaction(); + status = spi.write( R_RX_PAYLOAD ); + while ( data_len-- ) + *current++ = spi.write(0xff); + while ( blank_len-- ) + spi.write(0xff); + endTransaction(); + + return status; } /****************************************************************************/ uint8_t RF24::flush_rx(void) { - return spiTrans( FLUSH_RX ); + return spiTrans( FLUSH_RX ); } /****************************************************************************/ uint8_t RF24::flush_tx(void) { - return spiTrans( FLUSH_TX ); + return spiTrans( FLUSH_TX ); } /****************************************************************************/ -uint8_t RF24::spiTrans(uint8_t cmd){ - - uint8_t status; +uint8_t RF24::spiTrans(uint8_t cmd) +{ - beginTransaction(); - status = spi.write( cmd ); - endTransaction(); + uint8_t status; - - - - - - - - return status; + beginTransaction(); + status = spi.write( cmd ); + endTransaction(); + + return status; } /****************************************************************************/ uint8_t RF24::get_status(void) { - return spiTrans(NOP); + return spiTrans(NOP); } /****************************************************************************/ @@ -374,7 +206,7 @@ void RF24::print_observe_tx(uint8_t value) { - printf(("OBSERVE_TX=%02x: POLS_CNT=%x ARC_CNT=%x\r\n"), + printf(("OBSERVE_TX=%02x: POLS_CNT=%x ARC_CNT=%x\r\n"), value, ((value >> PLOS_CNT) & 15), ((value >> ARC_CNT) & 15) @@ -385,57 +217,48 @@ void RF24::print_byte_register(const char* name, uint8_t reg, uint8_t qty) { -printf("%s =",name); - while (qty--) - printf_P(PSTR(" 0x%02x"),read_register(reg++)); - printf_P(PSTR("\r\n")); - - - - - - + printf("%s =",name); + while (qty--) + printf_P(PSTR(" 0x%02x"),read_register(reg++)); + printf_P(PSTR("\r\n")); + } /****************************************************************************/ void RF24::print_address_register(const char* name, uint8_t reg, uint8_t qty) { - printf_P(PSTR(PRIPSTR"\t ="),name); - - while (qty--) - { - uint8_t buffer[addr_width]; - read_register(reg++,buffer,sizeof buffer); + printf_P(PSTR(PRIPSTR"\t ="),name); + + while (qty--) { + uint8_t buffer[addr_width]; + read_register(reg++,buffer,sizeof buffer); - printf_P(PSTR(" 0x")); - uint8_t* bufptr = buffer + sizeof buffer; - while( --bufptr >= buffer ) - printf_P(PSTR("%02x"),*bufptr); - } + printf_P(PSTR(" 0x")); + uint8_t* bufptr = buffer + sizeof buffer; + while( --bufptr >= buffer ) + printf_P(PSTR("%02x"),*bufptr); + } - printf_P(PSTR("\r\n")); - - - - + printf_P(PSTR("\r\n")); + } #endif /****************************************************************************/ - + RF24::RF24(PinName mosi, PinName miso, PinName sck, PinName _cepin, PinName _csnpin): - ce_pin(_cepin), csn_pin(_csnpin), p_variant(false), - payload_size(32), dynamic_payloads_enabled(false), addr_width(5), spi(mosi, miso, sck) + ce_pin(_cepin), csn_pin(_csnpin), p_variant(false), + payload_size(32), dynamic_payloads_enabled(false), addr_width(5), spi(mosi, miso, sck) { - pipe0_reading_address[0]=0; - spi.frequency(10000000/5); // 2Mbit, 1/5th the maximum transfer rate for the spi bus - spi.format(8,0); // 8-bit, ClockPhase = 0, ClockPolarity = 0 - - DigitalOut ce_pin(_cepin); /**< "Chip Enable" pin, activates the RX or TX role */ - DigitalOut csn_pin(_csnpin); /**< SPI Chip select */ - - wait_ms(100); - + pipe0_reading_address[0]=0; + spi.frequency(10000000/5); // 2Mbit, 1/5th the maximum transfer rate for the spi bus + spi.format(8,0); // 8-bit, ClockPhase = 0, ClockPolarity = 0 + + DigitalOut ce_pin(_cepin); /**< "Chip Enable" pin, activates the RX or TX role */ + DigitalOut csn_pin(_csnpin); /**< SPI Chip select */ + + wait_ms(100); + } @@ -449,26 +272,26 @@ void RF24::setChannel(uint8_t channel) { - const uint8_t max_channel = 127; - write_register(RF_CH,rf24_min(channel,max_channel)); + const uint8_t max_channel = 127; + write_register(RF_CH,rf24_min(channel,max_channel)); } uint8_t RF24::getChannel() { - return read_register(RF_CH); + return read_register(RF_CH); } /****************************************************************************/ void RF24::setPayloadSize(uint8_t size) { - payload_size = rf24_min(size,32); + payload_size = rf24_min(size,32); } /****************************************************************************/ uint8_t RF24::getPayloadSize(void) { - return payload_size; + return payload_size; } /****************************************************************************/ @@ -479,101 +302,55 @@ static const char rf24_datarate_e_str_1[] PROGMEM = "2MBPS"; static const char rf24_datarate_e_str_2[] PROGMEM = "250KBPS"; static const char * const rf24_datarate_e_str_P[] PROGMEM = { - rf24_datarate_e_str_0, - rf24_datarate_e_str_1, - rf24_datarate_e_str_2, + rf24_datarate_e_str_0, + rf24_datarate_e_str_1, + rf24_datarate_e_str_2, }; static const char rf24_model_e_str_0[] PROGMEM = "nRF24L01"; static const char rf24_model_e_str_1[] PROGMEM = "nRF24L01+"; static const char * const rf24_model_e_str_P[] PROGMEM = { - rf24_model_e_str_0, - rf24_model_e_str_1, + rf24_model_e_str_0, + rf24_model_e_str_1, }; static const char rf24_crclength_e_str_0[] PROGMEM = "Disabled"; static const char rf24_crclength_e_str_1[] PROGMEM = "8 bits"; static const char rf24_crclength_e_str_2[] PROGMEM = "16 bits" ; static const char * const rf24_crclength_e_str_P[] PROGMEM = { - rf24_crclength_e_str_0, - rf24_crclength_e_str_1, - rf24_crclength_e_str_2, + rf24_crclength_e_str_0, + rf24_crclength_e_str_1, + rf24_crclength_e_str_2, }; static const char rf24_pa_dbm_e_str_0[] PROGMEM = "PA_MIN"; static const char rf24_pa_dbm_e_str_1[] PROGMEM = "PA_LOW"; static const char rf24_pa_dbm_e_str_2[] PROGMEM = "PA_HIGH"; static const char rf24_pa_dbm_e_str_3[] PROGMEM = "PA_MAX"; static const char * const rf24_pa_dbm_e_str_P[] PROGMEM = { - rf24_pa_dbm_e_str_0, - rf24_pa_dbm_e_str_1, - rf24_pa_dbm_e_str_2, - rf24_pa_dbm_e_str_3, + rf24_pa_dbm_e_str_0, + rf24_pa_dbm_e_str_1, + rf24_pa_dbm_e_str_2, + rf24_pa_dbm_e_str_3, }; - - - - - - - - - - - - - void RF24::printDetails(void) { - - - - - - - - - - - - + print_status(get_status()); - - - - - - - - - - - - + print_address_register(PSTR("RX_ADDR_P0-1"),RX_ADDR_P0,2); + print_byte_register(PSTR("RX_ADDR_P2-5"),RX_ADDR_P2,4); + print_address_register(PSTR("TX_ADDR\t"),TX_ADDR); - - - - - - - - print_status(get_status()); - - print_address_register(PSTR("RX_ADDR_P0-1"),RX_ADDR_P0,2); - print_byte_register(PSTR("RX_ADDR_P2-5"),RX_ADDR_P2,4); - print_address_register(PSTR("TX_ADDR\t"),TX_ADDR); + print_byte_register(PSTR("RX_PW_P0-6"),RX_PW_P0,6); + print_byte_register(PSTR("EN_AA\t"),EN_AA); + print_byte_register(PSTR("EN_RXADDR"),EN_RXADDR); + print_byte_register(PSTR("RF_CH\t"),RF_CH); + print_byte_register(PSTR("RF_SETUP"),RF_SETUP); + print_byte_register(PSTR("CONFIG\t"),CONFIG); + print_byte_register(PSTR("DYNPD/FEATURE"),DYNPD,2); - print_byte_register(PSTR("RX_PW_P0-6"),RX_PW_P0,6); - print_byte_register(PSTR("EN_AA\t"),EN_AA); - print_byte_register(PSTR("EN_RXADDR"),EN_RXADDR); - print_byte_register(PSTR("RF_CH\t"),RF_CH); - print_byte_register(PSTR("RF_SETUP"),RF_SETUP); - print_byte_register(PSTR("CONFIG\t"),CONFIG); - print_byte_register(PSTR("DYNPD/FEATURE"),DYNPD,2); - - printf_P(PSTR("Data Rate\t = "PRIPSTR"\r\n"),pgm_read_word(&rf24_datarate_e_str_P[getDataRate()])); - printf_P(PSTR("Model\t\t = "PRIPSTR"\r\n"),pgm_read_word(&rf24_model_e_str_P[isPVariant()])); - printf_P(PSTR("CRC Length\t = "PRIPSTR"\r\n"),pgm_read_word(&rf24_crclength_e_str_P[getCRCLength()])); - printf_P(PSTR("PA Power\t = "PRIPSTR"\r\n"), pgm_read_word(&rf24_pa_dbm_e_str_P[getPALevel()])); + printf_P(PSTR("Data Rate\t = "PRIPSTR"\r\n"),pgm_read_word(&rf24_datarate_e_str_P[getDataRate()])); + printf_P(PSTR("Model\t\t = "PRIPSTR"\r\n"),pgm_read_word(&rf24_model_e_str_P[isPVariant()])); + printf_P(PSTR("CRC Length\t = "PRIPSTR"\r\n"),pgm_read_word(&rf24_crclength_e_str_P[getCRCLength()])); + printf_P(PSTR("PA Power\t = "PRIPSTR"\r\n"), pgm_read_word(&rf24_pa_dbm_e_str_P[getPALevel()])); } @@ -582,182 +359,130 @@ bool RF24::begin(void) { - - uint8_t setup=0; + uint8_t setup=0; - mainTimer.start(); - - ce_pin=LOW; - csn_pin=HIGH; + mainTimer.start(); + + ce_pin=LOW; + csn_pin=HIGH; - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - // Must allow the radio time to settle else configuration bits will not necessarily stick. - // This is actually only required following power up but some settling time also appears to - // be required after resets too. For full coverage, we'll always assume the worst. - // Enabling 16b CRC is by far the most obvious case if the wrong timing is used - or skipped. - // Technically we require 4.5ms + 14us as a worst case. We'll just call it 5ms for good measure. - // WARNING: Delay is based on P-variant whereby non-P *may* require different timing. - wait_ms( 5 ) ; + // Must allow the radio time to settle else configuration bits will not necessarily stick. + // This is actually only required following power up but some settling time also appears to + // be required after resets too. For full coverage, we'll always assume the worst. + // Enabling 16b CRC is by far the most obvious case if the wrong timing is used - or skipped. + // Technically we require 4.5ms + 14us as a worst case. We'll just call it 5ms for good measure. + // WARNING: Delay is based on P-variant whereby non-P *may* require different timing. + wait_ms( 5 ) ; + + // Reset CONFIG and enable 16-bit CRC. + write_register( CONFIG, 12 ) ; + + // Set 1500uS (minimum for 32B payload in ESB@250KBPS) timeouts, to make testing a little easier + // WARNING: If this is ever lowered, either 250KBS mode with AA is broken or maximum packet + // sizes must never be used. See documentation for a more complete explanation. + setRetries(5,15); + + // Reset value is MAX + setPALevel( RF24_PA_MAX ) ; - // Reset CONFIG and enable 16-bit CRC. - write_register( CONFIG, 12 ) ; - - // Set 1500uS (minimum for 32B payload in ESB@250KBPS) timeouts, to make testing a little easier - // WARNING: If this is ever lowered, either 250KBS mode with AA is broken or maximum packet - // sizes must never be used. See documentation for a more complete explanation. - setRetries(5,15); - - // Reset value is MAX - setPALevel( RF24_PA_MAX ) ; + // check for connected module and if this is a p nRF24l01 variant + // + if( setDataRate( RF24_250KBPS ) ) { + p_variant = true ; + } + /*setup = read_register(RF_SETUP); + if( setup == 0b00001110 ) // register default for nRF24L01P + { + p_variant = true ; + }*/ - // check for connected module and if this is a p nRF24l01 variant - // - if( setDataRate( RF24_250KBPS ) ) - { - p_variant = true ; - } - /*setup = read_register(RF_SETUP); - if( setup == 0b00001110 ) // register default for nRF24L01P - { - p_variant = true ; - }*/ - - // Then set the data rate to the slowest (and most reliable) speed supported by all - // hardware. - setDataRate( RF24_1MBPS ) ; + // Then set the data rate to the slowest (and most reliable) speed supported by all + // hardware. + setDataRate( RF24_1MBPS ) ; + + // Initialize CRC and request 2-byte (16bit) CRC + setCRCLength( RF24_CRC_16 ) ; - // Initialize CRC and request 2-byte (16bit) CRC - setCRCLength( RF24_CRC_16 ) ; + // Disable dynamic payloads, to match dynamic_payloads_enabled setting - Reset value is 0 + toggle_features(); + write_register(FEATURE,0 ); + write_register(DYNPD,0); - // Disable dynamic payloads, to match dynamic_payloads_enabled setting - Reset value is 0 - toggle_features(); - write_register(FEATURE,0 ); - write_register(DYNPD,0); - - // Reset current status - // Notice reset and flush is the last thing we do - write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); + // Reset current status + // Notice reset and flush is the last thing we do + write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); - // Set up default configuration. Callers can always change it later. - // This channel should be universally safe and not bleed over into adjacent - // spectrum. - setChannel(76); + // Set up default configuration. Callers can always change it later. + // This channel should be universally safe and not bleed over into adjacent + // spectrum. + setChannel(76); - // Flush buffers - flush_rx(); - flush_tx(); + // Flush buffers + flush_rx(); + flush_tx(); - powerUp(); //Power up by default when begin() is called + powerUp(); //Power up by default when begin() is called - // Enable PTX, do not write CE high so radio will remain in standby I mode ( 130us max to transition to RX or TX instead of 1500us from powerUp ) - // PTX should use only 22uA of power - write_register(CONFIG, ( read_register(CONFIG) ) & ~_BV(PRIM_RX) ); + // Enable PTX, do not write CE high so radio will remain in standby I mode ( 130us max to transition to RX or TX instead of 1500us from powerUp ) + // PTX should use only 22uA of power + write_register(CONFIG, ( read_register(CONFIG) ) & ~_BV(PRIM_RX) ); - // if setup is 0 or ff then there was no response from module - return ( setup != 0 && setup != 0xff ); + // if setup is 0 or ff then there was no response from module + return ( setup != 0 && setup != 0xff ); } /****************************************************************************/ void RF24::startListening(void) { - - + write_register(CONFIG, read_register(CONFIG) | _BV(PRIM_RX)); + write_register(NRF_STATUS, _BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); + ce(true); + // Restore the pipe0 adddress, if exists + if (pipe0_reading_address[0] > 0) { + write_register(RX_ADDR_P0, pipe0_reading_address, addr_width); + } else { + closeReadingPipe(0); + } - write_register(CONFIG, read_register(CONFIG) | _BV(PRIM_RX)); - write_register(NRF_STATUS, _BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); - ce(true); - // Restore the pipe0 adddress, if exists - if (pipe0_reading_address[0] > 0){ - write_register(RX_ADDR_P0, pipe0_reading_address, addr_width); - }else{ - closeReadingPipe(0); - } + // Flush buffers + //flush_rx(); + if(read_register(FEATURE) & _BV(EN_ACK_PAY)) { + flush_tx(); + } - // Flush buffers - //flush_rx(); - if(read_register(FEATURE) & _BV(EN_ACK_PAY)){ - flush_tx(); - } - - // Go! - //delayMicroseconds(100); + //wait_us(100); } /****************************************************************************/ -static const uint8_t child_pipe_enable[] PROGMEM = -{ - ERX_P0, ERX_P1, ERX_P2, ERX_P3, ERX_P4, ERX_P5 +static const uint8_t child_pipe_enable[] PROGMEM = { + ERX_P0, ERX_P1, ERX_P2, ERX_P3, ERX_P4, ERX_P5 }; void RF24::stopListening(void) -{ - ce_pin=LOW; +{ + ce_pin=LOW; + + wait_us(txRxDelay); - wait_us(txRxDelay); - - if(read_register(FEATURE) & _BV(EN_ACK_PAY)){ - wait_us(txRxDelay); //200 - flush_tx(); - } - //flush_rx(); - write_register(CONFIG, ( read_register(CONFIG) ) & ~_BV(PRIM_RX) ); - + if(read_register(FEATURE) & _BV(EN_ACK_PAY)) { + wait_us(txRxDelay); //200 + flush_tx(); + } + //flush_rx(); + write_register(CONFIG, ( read_register(CONFIG) ) & ~_BV(PRIM_RX) ); - - - - - - - write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[0]))); // Enable RX on pipe0 - - //delayMicroseconds(100); + write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[0]))); // Enable RX on pipe0 + //wait_us(100); } /****************************************************************************/ void RF24::powerDown(void) { - ce(false); // Guarantee CE is low on powerDown - write_register(CONFIG,read_register(CONFIG) & ~_BV(PWR_UP)); + ce(false); // Guarantee CE is low on powerDown + write_register(CONFIG,read_register(CONFIG) & ~_BV(PWR_UP)); } /****************************************************************************/ @@ -765,30 +490,31 @@ //Power up now. Radio will not power down unless instructed by MCU for config changes etc. void RF24::powerUp(void) { - uint8_t cfg = read_register(CONFIG); + uint8_t cfg = read_register(CONFIG); - // if not powered up then power up and wait for the radio to initialize - if (!(cfg & _BV(PWR_UP))){ - write_register(CONFIG,read_register(CONFIG) | _BV(PWR_UP)); + // if not powered up then power up and wait for the radio to initialize + if (!(cfg & _BV(PWR_UP))) { + write_register(CONFIG,read_register(CONFIG) | _BV(PWR_UP)); - // For nRF24L01+ to go from power down mode to TX or RX mode it must first pass through stand-by mode. - // There must be a delay of Tpd2stby (see Table 16.) after the nRF24L01+ leaves power down mode before - // the CEis set high. - Tpd2stby can be up to 5ms per the 1.0 datasheet - wait_ms(5); - } + // For nRF24L01+ to go from power down mode to TX or RX mode it must first pass through stand-by mode. + // There must be a delay of Tpd2stby (see Table 16.) after the nRF24L01+ leaves power down mode before + // the CEis set high. - Tpd2stby can be up to 5ms per the 1.0 datasheet + wait_ms(5); + } } /******************************************************************/ -#if defined (FAILURE_HANDLING) -void RF24::errNotify(){ - #if defined (SERIAL_DEBUG) - printf_P(PSTR("RF24 HARDWARE FAIL: Radio not responding, verify pin connections, wiring, etc.\r\n")); - #endif - #if defined (FAILURE_HANDLING) +#if defined (FAILURE_HANDLING) +void RF24::errNotify() +{ +#if defined (SERIAL_DEBUG) + printf_P(PSTR("RF24 HARDWARE FAIL: Radio not responding, verify pin connections, wiring, etc.\r\n")); +#endif +#if defined (FAILURE_HANDLING) failureDetected = 1; - #else +#else wait_ms(5000); - #endif +#endif } #endif /******************************************************************/ @@ -800,37 +526,38 @@ startFastWrite(buf,len,multicast); //Wait until complete or failed - #if defined (FAILURE_HANDLING) - uint32_t timer = mainTimer.read_ms(); - #endif - - while( ! ( get_status() & ( _BV(TX_DS) | _BV(MAX_RT) ))) { - #if defined (FAILURE_HANDLING) - if(mainTimer.read_ms() - timer > 85){ - errNotify(); - #if defined (FAILURE_HANDLING) - return 0; - #else - wait_ms(100); - #endif - } - #endif +#if defined (FAILURE_HANDLING) + uint32_t timer = mainTimer.read_ms(); +#endif + + while( ! ( get_status() & ( _BV(TX_DS) | _BV(MAX_RT) ))) { +#if defined (FAILURE_HANDLING) + if(mainTimer.read_ms() - timer > 85) { + errNotify(); +#if defined (FAILURE_HANDLING) + return 0; +#else + wait_ms(100); +#endif + } +#endif } - + ce_pin=LOW; uint8_t status = write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); - //Max retries exceeded - if( status & _BV(MAX_RT)){ - flush_tx(); //Only going to be 1 packet int the FIFO at a time using this method, so just flush - return 0; - } + //Max retries exceeded + if( status & _BV(MAX_RT)) { + flush_tx(); //Only going to be 1 packet int the FIFO at a time using this method, so just flush + return 0; + } //TX OK 1 or 0 - return 1; + return 1; } -bool RF24::write( const void* buf, uint8_t len ){ +bool RF24::write( const void* buf, uint8_t len ) +{ return write(buf,len,0); } /****************************************************************************/ @@ -847,19 +574,20 @@ while( ( get_status() & ( _BV(TX_FULL) ))) { //Blocking only if FIFO is full. This will loop and block until TX is successful or timeout - if( get_status() & _BV(MAX_RT)){ //If MAX Retries have been reached + if( get_status() & _BV(MAX_RT)) { //If MAX Retries have been reached reUseTX(); //Set re-transmit and clear the MAX_RT interrupt flag - if(mainTimer.read_ms() - timer > timeout){ return 0; } //If this payload has exceeded the user-defined timeout, exit and return 0 + if(mainTimer.read_ms() - timer > timeout) { + return 0; //If this payload has exceeded the user-defined timeout, exit and return 0 + } } - #if defined (FAILURE_HANDLING) - if(mainTimer.read_ms() - timer > (timeout+85) ){ - errNotify(); - #if defined (FAILURE_HANDLING) - return 0; - #endif - } - #endif - +#if defined (FAILURE_HANDLING) + if(mainTimer.read_ms() - timer > (timeout+85) ) { + errNotify(); +#if defined (FAILURE_HANDLING) + return 0; +#endif + } +#endif } //Start Writing @@ -870,11 +598,12 @@ /****************************************************************************/ -void RF24::reUseTX(){ - write_register(NRF_STATUS,_BV(MAX_RT) ); //Clear max retry flag - spiTrans( REUSE_TX_PL ); - ce_pin=LOW; //Re-Transfer packet - ce_pin=HIGH; +void RF24::reUseTX() +{ + write_register(NRF_STATUS,_BV(MAX_RT) ); //Clear max retry flag + spiTrans( REUSE_TX_PL ); + ce_pin=LOW; //Re-Transfer packet + ce_pin=HIGH; } /****************************************************************************/ @@ -886,34 +615,35 @@ //Return 0 so the user can control the retrys and set a timer or failure counter if required //The radio will auto-clear everything in the FIFO as long as CE remains high - #if defined (FAILURE_HANDLING) - uint32_t timer = mainTimer.read_ms(); - #endif - +#if defined (FAILURE_HANDLING) + uint32_t timer = mainTimer.read_ms(); +#endif + while( ( get_status() & ( _BV(TX_FULL) ))) { //Blocking only if FIFO is full. This will loop and block until TX is successful or fail - if( get_status() & _BV(MAX_RT)){ + if( get_status() & _BV(MAX_RT)) { //reUseTX(); //Set re-transmit write_register(NRF_STATUS,_BV(MAX_RT) ); //Clear max retry flag return 0; //Return 0. The previous payload has been retransmitted - //From the user perspective, if you get a 0, just keep trying to send the same payload + //From the user perspective, if you get a 0, just keep trying to send the same payload } - #if defined (FAILURE_HANDLING) - if(mainTimer.read_ms() - timer > 85 ){ - errNotify(); - #if defined (FAILURE_HANDLING) - return 0; - #endif - } - #endif +#if defined (FAILURE_HANDLING) + if(mainTimer.read_ms() - timer > 85 ) { + errNotify(); +#if defined (FAILURE_HANDLING) + return 0; +#endif + } +#endif } - //Start Writing + //Start Writing startFastWrite(buf,len,multicast); return 1; } -bool RF24::writeFast( const void* buf, uint8_t len ){ +bool RF24::writeFast( const void* buf, uint8_t len ) +{ return writeFast(buf,len,0); } @@ -924,62 +654,63 @@ //Otherwise we enter Standby-II mode, which is still faster than standby mode //Also, we remove the need to keep writing the config register over and over and delaying for 150 us each time if sending a stream of data -void RF24::startFastWrite( const void* buf, uint8_t len, const bool multicast, bool startTx){ //TMRh20 +void RF24::startFastWrite( const void* buf, uint8_t len, const bool multicast, bool startTx) //TMRh20 +{ //write_payload( buf,len); write_payload( buf, len,multicast ? W_TX_PAYLOAD_NO_ACK : W_TX_PAYLOAD ) ; - if(startTx){ + if(startTx) { ce_pin=HIGH; } - } /****************************************************************************/ //Added the original startWrite back in so users can still use interrupts, ack payloads, etc //Allows the library to pass all tests -void RF24::startWrite( const void* buf, uint8_t len, const bool multicast ){ +void RF24::startWrite( const void* buf, uint8_t len, const bool multicast ) +{ - // Send the payload + // Send the payload - //write_payload( buf, len ); - write_payload( buf, len,multicast? W_TX_PAYLOAD_NO_ACK : W_TX_PAYLOAD ) ; - ce_pin=HIGH; - + //write_payload( buf, len ); + write_payload( buf, len,multicast? W_TX_PAYLOAD_NO_ACK : W_TX_PAYLOAD ) ; + ce_pin=HIGH; + wait_us(10); - - ce_pin=LOW; - + ce_pin=LOW; } /****************************************************************************/ -bool RF24::rxFifoFull(){ +bool RF24::rxFifoFull() +{ return read_register(FIFO_STATUS) & _BV(RX_FULL); } /****************************************************************************/ -bool RF24::txStandBy(){ +bool RF24::txStandBy() +{ - #if defined (FAILURE_HANDLING) - uint32_t timeout = mainTimer.read_ms(); - #endif - while( ! (read_register(FIFO_STATUS) & _BV(TX_EMPTY)) ){ - if( get_status() & _BV(MAX_RT)){ +#if defined (FAILURE_HANDLING) + uint32_t timeout = mainTimer.read_ms(); +#endif + while( ! (read_register(FIFO_STATUS) & _BV(TX_EMPTY)) ) { + if( get_status() & _BV(MAX_RT)) { write_register(NRF_STATUS,_BV(MAX_RT) ); ce_pin=LOW; flush_tx(); //Non blocking, flush the data return 0; } - #if defined (FAILURE_HANDLING) - if( mainTimer.read_ms() - timeout > 85){ - errNotify(); - #if defined (FAILURE_HANDLING) - return 0; - #endif - } - #endif +#if defined (FAILURE_HANDLING) + if( mainTimer.read_ms() - timeout > 85) { + errNotify(); +#if defined (FAILURE_HANDLING) + return 0; +#endif + } +#endif } ce_pin=LOW; //Set STANDBY-I mode @@ -988,34 +719,36 @@ /****************************************************************************/ -bool RF24::txStandBy(uint32_t timeout, bool startTx){ +bool RF24::txStandBy(uint32_t timeout, bool startTx) +{ - if(startTx){ - stopListening(); - ce_pin=HIGH; + if(startTx) { + stopListening(); + ce_pin=HIGH; } uint32_t start = mainTimer.read_ms(); - while( ! (read_register(FIFO_STATUS) & _BV(TX_EMPTY)) ){ - if( get_status() & _BV(MAX_RT)){ + while( ! (read_register(FIFO_STATUS) & _BV(TX_EMPTY)) ) { + if( get_status() & _BV(MAX_RT)) { write_register(NRF_STATUS,_BV(MAX_RT) ); - ce_pin=LOW; //Set re-transmit - ce_pin=HIGH; - if(mainTimer.read_ms() - start >= timeout){ - ce_pin=LOW;; flush_tx(); return 0; - } + ce_pin=LOW; //Set re-transmit + ce_pin=HIGH; + if(mainTimer.read_ms() - start >= timeout) { + ce_pin=LOW;; + flush_tx(); + return 0; + } } - #if defined (FAILURE_HANDLING) - if( mainTimer.read_ms() - start > (timeout+85)){ - errNotify(); - #if defined (FAILURE_HANDLING) - return 0; - #endif - } - #endif +#if defined (FAILURE_HANDLING) + if( mainTimer.read_ms() - start > (timeout+85)) { + errNotify(); +#if defined (FAILURE_HANDLING) + return 0; +#endif + } +#endif } - ce_pin=LOW; //Set STANDBY-I mode return 1; @@ -1023,7 +756,8 @@ /****************************************************************************/ -void RF24::maskIRQ(bool tx, bool fail, bool rx){ +void RF24::maskIRQ(bool tx, bool fail, bool rx) +{ write_register(CONFIG, ( read_register(CONFIG) ) | fail << MASK_MAX_RT | tx << MASK_TX_DS | rx << MASK_RX_DR ); } @@ -1032,31 +766,27 @@ uint8_t RF24::getDynamicPayloadSize(void) { - uint8_t result = 0; + uint8_t result = 0; + + beginTransaction(); + spi.write( R_RX_PL_WID ); + result = spi.write(0xff); + endTransaction(); - - - - - - - - - beginTransaction(); - spi.write( R_RX_PL_WID ); - result = spi.write(0xff); - endTransaction(); - - if(result > 32) { flush_rx(); wait_ms(2); return 0; } - return result; + if(result > 32) { + flush_rx(); + wait_ms(2); + return 0; + } + return result; } /****************************************************************************/ bool RF24::available(void) { - return available(NULL); + return available(NULL); } /****************************************************************************/ @@ -1072,149 +802,140 @@ } return 1; } - - + return 0; - - } /****************************************************************************/ -void RF24::read( void* buf, uint8_t len ){ +void RF24::read( void* buf, uint8_t len ) +{ - // Fetch the payload - read_payload( buf, len ); + // Fetch the payload + read_payload( buf, len ); - //Clear the two possible interrupt flags with one command - write_register(NRF_STATUS,_BV(RX_DR) | _BV(MAX_RT) | _BV(TX_DS) ); - + //Clear the two possible interrupt flags with one command + write_register(NRF_STATUS,_BV(RX_DR) | _BV(MAX_RT) | _BV(TX_DS) ); } /****************************************************************************/ void RF24::whatHappened(bool& tx_ok,bool& tx_fail,bool& rx_ready) { - // Read the status & reset the status in one easy call - // Or is that such a good idea? - uint8_t status = write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); + // Read the status & reset the status in one easy call + // Or is that such a good idea? + uint8_t status = write_register(NRF_STATUS,_BV(RX_DR) | _BV(TX_DS) | _BV(MAX_RT) ); - // Report to the user what happened - tx_ok = status & _BV(TX_DS); - tx_fail = status & _BV(MAX_RT); - rx_ready = status & _BV(RX_DR); + // Report to the user what happened + tx_ok = status & _BV(TX_DS); + tx_fail = status & _BV(MAX_RT); + rx_ready = status & _BV(RX_DR); } /****************************************************************************/ void RF24::openWritingPipe(uint64_t value) { - // Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+) - // expects it LSB first too, so we're good. + // Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+) + // expects it LSB first too, so we're good. - write_register(RX_ADDR_P0, reinterpret_cast<uint8_t*>(&value), addr_width); - write_register(TX_ADDR, reinterpret_cast<uint8_t*>(&value), addr_width); - - - //const uint8_t max_payload_size = 32; - //write_register(RX_PW_P0,rf24_min(payload_size,max_payload_size)); - write_register(RX_PW_P0,payload_size); + write_register(RX_ADDR_P0, reinterpret_cast<uint8_t*>(&value), addr_width); + write_register(TX_ADDR, reinterpret_cast<uint8_t*>(&value), addr_width); + + //const uint8_t max_payload_size = 32; + //write_register(RX_PW_P0,rf24_min(payload_size,max_payload_size)); + write_register(RX_PW_P0,payload_size); } /****************************************************************************/ void RF24::openWritingPipe(const uint8_t *address) { - // Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+) - // expects it LSB first too, so we're good. + // Note that AVR 8-bit uC's store this LSB first, and the NRF24L01(+) + // expects it LSB first too, so we're good. - write_register(RX_ADDR_P0,address, addr_width); - write_register(TX_ADDR, address, addr_width); + write_register(RX_ADDR_P0,address, addr_width); + write_register(TX_ADDR, address, addr_width); - //const uint8_t max_payload_size = 32; - //write_register(RX_PW_P0,rf24_min(payload_size,max_payload_size)); - write_register(RX_PW_P0,payload_size); + //const uint8_t max_payload_size = 32; + //write_register(RX_PW_P0,rf24_min(payload_size,max_payload_size)); + write_register(RX_PW_P0,payload_size); } /****************************************************************************/ -static const uint8_t child_pipe[] PROGMEM = -{ - RX_ADDR_P0, RX_ADDR_P1, RX_ADDR_P2, RX_ADDR_P3, RX_ADDR_P4, RX_ADDR_P5 +static const uint8_t child_pipe[] PROGMEM = { + RX_ADDR_P0, RX_ADDR_P1, RX_ADDR_P2, RX_ADDR_P3, RX_ADDR_P4, RX_ADDR_P5 }; -static const uint8_t child_payload_size[] PROGMEM = -{ - RX_PW_P0, RX_PW_P1, RX_PW_P2, RX_PW_P3, RX_PW_P4, RX_PW_P5 +static const uint8_t child_payload_size[] PROGMEM = { + RX_PW_P0, RX_PW_P1, RX_PW_P2, RX_PW_P3, RX_PW_P4, RX_PW_P5 }; void RF24::openReadingPipe(uint8_t child, uint64_t address) { - // If this is pipe 0, cache the address. This is needed because - // openWritingPipe() will overwrite the pipe 0 address, so - // startListening() will have to restore it. - if (child == 0){ - memcpy(pipe0_reading_address,&address,addr_width); - } + // If this is pipe 0, cache the address. This is needed because + // openWritingPipe() will overwrite the pipe 0 address, so + // startListening() will have to restore it. + if (child == 0) { + memcpy(pipe0_reading_address,&address,addr_width); + } - if (child <= 6) - { - // For pipes 2-5, only write the LSB - if ( child < 2 ) - write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), addr_width); - else - write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), 1); + if (child <= 6) { + // For pipes 2-5, only write the LSB + if ( child < 2 ) + write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), addr_width); + else + write_register(pgm_read_byte(&child_pipe[child]), reinterpret_cast<const uint8_t*>(&address), 1); - write_register(pgm_read_byte(&child_payload_size[child]),payload_size); + write_register(pgm_read_byte(&child_payload_size[child]),payload_size); - // Note it would be more efficient to set all of the bits for all open - // pipes at once. However, I thought it would make the calling code - // more simple to do it this way. - write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[child]))); - } + // Note it would be more efficient to set all of the bits for all open + // pipes at once. However, I thought it would make the calling code + // more simple to do it this way. + write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[child]))); + } } /****************************************************************************/ -void RF24::setAddressWidth(uint8_t a_width){ +void RF24::setAddressWidth(uint8_t a_width) +{ - if(a_width -= 2){ + if(a_width -= 2) { write_register(SETUP_AW,a_width%4); addr_width = (a_width%4) + 2; } - } /****************************************************************************/ void RF24::openReadingPipe(uint8_t child, const uint8_t *address) { - // If this is pipe 0, cache the address. This is needed because - // openWritingPipe() will overwrite the pipe 0 address, so - // startListening() will have to restore it. - if (child == 0){ - memcpy(pipe0_reading_address,address,addr_width); - } - if (child <= 6) - { - // For pipes 2-5, only write the LSB - if ( child < 2 ){ - write_register(pgm_read_byte(&child_pipe[child]), address, addr_width); - }else{ - write_register(pgm_read_byte(&child_pipe[child]), address, 1); + // If this is pipe 0, cache the address. This is needed because + // openWritingPipe() will overwrite the pipe 0 address, so + // startListening() will have to restore it. + if (child == 0) { + memcpy(pipe0_reading_address,address,addr_width); } - write_register(pgm_read_byte(&child_payload_size[child]),payload_size); + if (child <= 6) { + // For pipes 2-5, only write the LSB + if ( child < 2 ) { + write_register(pgm_read_byte(&child_pipe[child]), address, addr_width); + } else { + write_register(pgm_read_byte(&child_pipe[child]), address, 1); + } + write_register(pgm_read_byte(&child_payload_size[child]),payload_size); - // Note it would be more efficient to set all of the bits for all open - // pipes at once. However, I thought it would make the calling code - // more simple to do it this way. - write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[child]))); - - } + // Note it would be more efficient to set all of the bits for all open + // pipes at once. However, I thought it would make the calling code + // more simple to do it this way. + write_register(EN_RXADDR,read_register(EN_RXADDR) | _BV(pgm_read_byte(&child_pipe_enable[child]))); + } } /****************************************************************************/ void RF24::closeReadingPipe( uint8_t pipe ) { - write_register(EN_RXADDR,read_register(EN_RXADDR) & ~_BV(pgm_read_byte(&child_pipe_enable[pipe]))); + write_register(EN_RXADDR,read_register(EN_RXADDR) & ~_BV(pgm_read_byte(&child_pipe_enable[pipe]))); } /****************************************************************************/ @@ -1225,69 +946,60 @@ spi.write( ACTIVATE ); spi.write( 0x73 ); endTransaction(); - - - - - - - - - } /****************************************************************************/ void RF24::enableDynamicPayloads(void) { - // Enable dynamic payload throughout the system + // Enable dynamic payload throughout the system //toggle_features(); write_register(FEATURE,read_register(FEATURE) | _BV(EN_DPL) ); - - IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); + IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); - // Enable dynamic payload on all pipes - // - // Not sure the use case of only having dynamic payload on certain - // pipes, so the library does not support it. - write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P5) | _BV(DPL_P4) | _BV(DPL_P3) | _BV(DPL_P2) | _BV(DPL_P1) | _BV(DPL_P0)); + // Enable dynamic payload on all pipes + // + // Not sure the use case of only having dynamic payload on certain + // pipes, so the library does not support it. + write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P5) | _BV(DPL_P4) | _BV(DPL_P3) | _BV(DPL_P2) | _BV(DPL_P1) | _BV(DPL_P0)); - dynamic_payloads_enabled = true; + dynamic_payloads_enabled = true; } /****************************************************************************/ void RF24::enableAckPayload(void) { - // - // enable ack payload and dynamic payload features - // + // + // enable ack payload and dynamic payload features + // //toggle_features(); write_register(FEATURE,read_register(FEATURE) | _BV(EN_ACK_PAY) | _BV(EN_DPL) ); - IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); + IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); - // - // Enable dynamic payload on pipes 0 & 1 - // + // + // Enable dynamic payload on pipes 0 & 1 + // - write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P1) | _BV(DPL_P0)); - dynamic_payloads_enabled = true; + write_register(DYNPD,read_register(DYNPD) | _BV(DPL_P1) | _BV(DPL_P0)); + dynamic_payloads_enabled = true; } /****************************************************************************/ -void RF24::enableDynamicAck(void){ - // - // enable dynamic ack features - // +void RF24::enableDynamicAck(void) +{ + // + // enable dynamic ack features + // //toggle_features(); write_register(FEATURE,read_register(FEATURE) | _BV(EN_DYN_ACK) ); - IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); + IF_SERIAL_DEBUG(printf("FEATURE=%i\r\n",read_register(FEATURE))); } @@ -1296,16 +1008,16 @@ void RF24::writeAckPayload(uint8_t pipe, const void* buf, uint8_t len) { - const uint8_t* current = reinterpret_cast<const uint8_t*>(buf); + const uint8_t* current = reinterpret_cast<const uint8_t*>(buf); - uint8_t data_len = rf24_min(len,32); + uint8_t data_len = rf24_min(len,32); - beginTransaction(); - spi.write(W_ACK_PAYLOAD | ( pipe & 7 ) ); + beginTransaction(); + spi.write(W_ACK_PAYLOAD | ( pipe & 7 ) ); - while ( data_len-- ) - spi.write(*current++); - endTransaction(); + while ( data_len-- ) + spi.write(*current++); + endTransaction(); } @@ -1313,57 +1025,53 @@ bool RF24::isAckPayloadAvailable(void) { - return ! (read_register(FIFO_STATUS) & _BV(RX_EMPTY)); + return ! (read_register(FIFO_STATUS) & _BV(RX_EMPTY)); } /****************************************************************************/ bool RF24::isPVariant(void) { - return p_variant ; + return p_variant ; } /****************************************************************************/ void RF24::setAutoAck(bool enable) { - if ( enable ) - write_register(EN_AA, 63); - else - write_register(EN_AA, 0); + if ( enable ) + write_register(EN_AA, 63); + else + write_register(EN_AA, 0); } /****************************************************************************/ void RF24::setAutoAck( uint8_t pipe, bool enable ) { - if ( pipe <= 6 ) - { - uint8_t en_aa = read_register( EN_AA ) ; - if( enable ) - { - en_aa |= _BV(pipe) ; + if ( pipe <= 6 ) { + uint8_t en_aa = read_register( EN_AA ) ; + if( enable ) { + en_aa |= _BV(pipe) ; + } else { + en_aa &= ~_BV(pipe) ; + } + write_register( EN_AA, en_aa ) ; } - else - { - en_aa &= ~_BV(pipe) ; - } - write_register( EN_AA, en_aa ) ; - } } /****************************************************************************/ bool RF24::testCarrier(void) { - return ( read_register(CD) & 1 ); + return ( read_register(CD) & 1 ); } /****************************************************************************/ bool RF24::testRPD(void) { - return ( read_register(RPD) & 1 ) ; + return ( read_register(RPD) & 1 ) ; } /****************************************************************************/ @@ -1371,16 +1079,16 @@ void RF24::setPALevel(uint8_t level) { - uint8_t setup = read_register(RF_SETUP) & 248; + uint8_t setup = read_register(RF_SETUP) & 248; - if(level > 3){ // If invalid level, go to max PA - level = (RF24_PA_MAX << 1) + 1; // +1 to support the SI24R1 chip extra bit - }else{ - level = (level << 1) + 1; // Else set level as requested - } + if(level > 3) { // If invalid level, go to max PA + level = (RF24_PA_MAX << 1) + 1; // +1 to support the SI24R1 chip extra bit + } else { + level = (level << 1) + 1; // Else set level as requested + } - write_register( RF_SETUP, setup |= level ) ; // Write it to the chip + write_register( RF_SETUP, setup |= level ) ; // Write it to the chip } /****************************************************************************/ @@ -1388,129 +1096,112 @@ uint8_t RF24::getPALevel(void) { - return (read_register(RF_SETUP) & (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH))) >> 1 ; + return (read_register(RF_SETUP) & (_BV(RF_PWR_LOW) | _BV(RF_PWR_HIGH))) >> 1 ; } /****************************************************************************/ bool RF24::setDataRate(rf24_datarate_e speed) { - bool result = false; - uint8_t setup = read_register(RF_SETUP) ; + bool result = false; + uint8_t setup = read_register(RF_SETUP) ; - // HIGH and LOW '00' is 1Mbs - our default - setup &= ~(_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)) ; - + // HIGH and LOW '00' is 1Mbs - our default + setup &= ~(_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)) ; txRxDelay=85; - if( speed == RF24_250KBPS ) - { - // Must set the RF_DR_LOW to 1; RF_DR_HIGH (used to be RF_DR) is already 0 - // Making it '10'. - setup |= _BV( RF_DR_LOW ) ; - txRxDelay=155; - } - else - { - // Set 2Mbs, RF_DR (RF_DR_HIGH) is set 1 - // Making it '01' - if ( speed == RF24_2MBPS ) - { - setup |= _BV(RF_DR_HIGH); - txRxDelay=65; + if( speed == RF24_250KBPS ) { + // Must set the RF_DR_LOW to 1; RF_DR_HIGH (used to be RF_DR) is already 0 + // Making it '10'. + setup |= _BV( RF_DR_LOW ) ; + txRxDelay=155; + } else { + // Set 2Mbs, RF_DR (RF_DR_HIGH) is set 1 + // Making it '01' + if ( speed == RF24_2MBPS ) { + setup |= _BV(RF_DR_HIGH); + txRxDelay=65; + } } - } - write_register(RF_SETUP,setup); + write_register(RF_SETUP,setup); - // Verify our result - if ( read_register(RF_SETUP) == setup ) - { - result = true; - } - return result; + // Verify our result + if ( read_register(RF_SETUP) == setup ) { + result = true; + } + return result; } /****************************************************************************/ rf24_datarate_e RF24::getDataRate( void ) { - rf24_datarate_e result ; - uint8_t dr = read_register(RF_SETUP) & (_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)); + rf24_datarate_e result ; + uint8_t dr = read_register(RF_SETUP) & (_BV(RF_DR_LOW) | _BV(RF_DR_HIGH)); - // switch uses RAM (evil!) - // Order matters in our case below - if ( dr == _BV(RF_DR_LOW) ) - { - // '10' = 250KBPS - result = RF24_250KBPS ; - } - else if ( dr == _BV(RF_DR_HIGH) ) - { - // '01' = 2MBPS - result = RF24_2MBPS ; - } - else - { - // '00' = 1MBPS - result = RF24_1MBPS ; - } - return result ; + // switch uses RAM (evil!) + // Order matters in our case below + if ( dr == _BV(RF_DR_LOW) ) { + // '10' = 250KBPS + result = RF24_250KBPS ; + } else if ( dr == _BV(RF_DR_HIGH) ) { + // '01' = 2MBPS + result = RF24_2MBPS ; + } else { + // '00' = 1MBPS + result = RF24_1MBPS ; + } + return result ; } /****************************************************************************/ void RF24::setCRCLength(rf24_crclength_e length) { - uint8_t config = read_register(CONFIG) & ~( _BV(CRCO) | _BV(EN_CRC)) ; + uint8_t config = read_register(CONFIG) & ~( _BV(CRCO) | _BV(EN_CRC)) ; - // switch uses RAM (evil!) - if ( length == RF24_CRC_DISABLED ) - { - // Do nothing, we turned it off above. - } - else if ( length == RF24_CRC_8 ) - { - config |= _BV(EN_CRC); - } - else - { - config |= _BV(EN_CRC); - config |= _BV( CRCO ); - } - write_register( CONFIG, config ) ; + // switch uses RAM (evil!) + if ( length == RF24_CRC_DISABLED ) { + // Do nothing, we turned it off above. + } else if ( length == RF24_CRC_8 ) { + config |= _BV(EN_CRC); + } else { + config |= _BV(EN_CRC); + config |= _BV( CRCO ); + } + write_register( CONFIG, config ) ; } /****************************************************************************/ rf24_crclength_e RF24::getCRCLength(void) { - rf24_crclength_e result = RF24_CRC_DISABLED; - - uint8_t config = read_register(CONFIG) & ( _BV(CRCO) | _BV(EN_CRC)) ; - uint8_t AA = read_register(EN_AA); - - if ( config & _BV(EN_CRC ) || AA) - { - if ( config & _BV(CRCO) ) - result = RF24_CRC_16; - else - result = RF24_CRC_8; - } + rf24_crclength_e result = RF24_CRC_DISABLED; + + uint8_t config = read_register(CONFIG) & ( _BV(CRCO) | _BV(EN_CRC)) ; + uint8_t AA = read_register(EN_AA); - return result; + if ( config & _BV(EN_CRC ) || AA) { + if ( config & _BV(CRCO) ) + result = RF24_CRC_16; + else + result = RF24_CRC_8; + } + + return result; } /****************************************************************************/ void RF24::disableCRC( void ) { - uint8_t disable = read_register(CONFIG) & ~_BV(EN_CRC) ; - write_register( CONFIG, disable ) ; + uint8_t disable = read_register(CONFIG) & ~_BV(EN_CRC) ; + write_register( CONFIG, disable ) ; } /****************************************************************************/ void RF24::setRetries(uint8_t delay, uint8_t count) { - write_register(SETUP_RETR,(delay&0xf)<<ARD | (count&0xf)<<ARC); + write_register(SETUP_RETR,(delay&0xf)<<ARD | (count&0xf)<<ARC); }