![](/media/cache/profiles/98c39996bf1543e974747a2549b3107c.50x50_q85.png)
LINKED LIST TEST on mbed
Diff: I2S_Example/lpc17xx_uart.c
- Revision:
- 0:e8bfffbb3ab6
diff -r 000000000000 -r e8bfffbb3ab6 I2S_Example/lpc17xx_uart.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/I2S_Example/lpc17xx_uart.c Sat Feb 26 03:55:12 2011 +0000 @@ -0,0 +1,1366 @@ +/***********************************************************************//** + * @file lpc17xx_uart.c + * @brief Contains all functions support for UART firmware library on LPC17xx + * @version 3.0 + * @date 18. June. 2010 + * @author NXP MCU SW Application Team + ************************************************************************** + * Software that is described herein is for illustrative purposes only + * which provides customers with programming information regarding the + * products. This software is supplied "AS IS" without any warranties. + * NXP Semiconductors assumes no responsibility or liability for the + * use of the software, conveys no license or title under any patent, + * copyright, or mask work right to the product. NXP Semiconductors + * reserves the right to make changes in the software without + * notification. NXP Semiconductors also make no representation or + * warranty that such application will be suitable for the specified + * use without further testing or modification. + **********************************************************************/ + +/* Peripheral group ----------------------------------------------------------- */ +/** @addtogroup UART + * @{ + */ + +/* Includes ------------------------------------------------------------------- */ +#include "lpc17xx_uart.h" +#include "lpc17xx_clkpwr.h" + +/* If this source file built with example, the LPC17xx FW library configuration + * file in each example directory ("lpc17xx_libcfg.h") must be included, + * otherwise the default FW library configuration file must be included instead + */ +#ifdef __BUILD_WITH_EXAMPLE__ +#include "lpc17xx_libcfg.h" +#else +#include "lpc17xx_libcfg_default.h" +#endif /* __BUILD_WITH_EXAMPLE__ */ + + +#ifdef _UART + +/* Private Functions ---------------------------------------------------------- */ + +static Status uart_set_divisors(LPC_UART_TypeDef *UARTx, uint32_t baudrate); + + +/*********************************************************************//** + * @brief Determines best dividers to get a target clock rate + * @param[in] UARTx Pointer to selected UART peripheral, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] baudrate Desired UART baud rate. + * @return Error status, could be: + * - SUCCESS + * - ERROR + **********************************************************************/ +static Status uart_set_divisors(LPC_UART_TypeDef *UARTx, uint32_t baudrate) +{ + Status errorStatus = ERROR; + + uint32_t uClk = 0; + uint32_t calcBaudrate = 0; + uint32_t temp = 0; + + uint32_t mulFracDiv, dividerAddFracDiv; + uint32_t diviser = 0 ; + uint32_t mulFracDivOptimal = 1; + uint32_t dividerAddOptimal = 0; + uint32_t diviserOptimal = 0; + + uint32_t relativeError = 0; + uint32_t relativeOptimalError = 100000; + + /* get UART block clock */ + if (UARTx == (LPC_UART_TypeDef *)LPC_UART0) + { + uClk = CLKPWR_GetPCLK (CLKPWR_PCLKSEL_UART0); + } + else if (UARTx == (LPC_UART_TypeDef *)LPC_UART1) + { + uClk = CLKPWR_GetPCLK (CLKPWR_PCLKSEL_UART1); + } + else if (UARTx == LPC_UART2) + { + uClk = CLKPWR_GetPCLK (CLKPWR_PCLKSEL_UART2); + } + else if (UARTx == LPC_UART3) + { + uClk = CLKPWR_GetPCLK (CLKPWR_PCLKSEL_UART3); + } + + + uClk = uClk >> 4; /* div by 16 */ + /* In the Uart IP block, baud rate is calculated using FDR and DLL-DLM registers + * The formula is : + * BaudRate= uClk * (mulFracDiv/(mulFracDiv+dividerAddFracDiv) / (16 * (DLL) + * It involves floating point calculations. That's the reason the formulae are adjusted with + * Multiply and divide method.*/ + /* The value of mulFracDiv and dividerAddFracDiv should comply to the following expressions: + * 0 < mulFracDiv <= 15, 0 <= dividerAddFracDiv <= 15 */ + for (mulFracDiv = 1 ; mulFracDiv <= 15 ;mulFracDiv++) + { + for (dividerAddFracDiv = 0 ; dividerAddFracDiv <= 15 ;dividerAddFracDiv++) + { + temp = (mulFracDiv * uClk) / ((mulFracDiv + dividerAddFracDiv)); + + diviser = temp / baudrate; + if ((temp % baudrate) > (baudrate / 2)) + diviser++; + + if (diviser > 2 && diviser < 65536) + { + calcBaudrate = temp / diviser; + + if (calcBaudrate <= baudrate) + relativeError = baudrate - calcBaudrate; + else + relativeError = calcBaudrate - baudrate; + + if ((relativeError < relativeOptimalError)) + { + mulFracDivOptimal = mulFracDiv ; + dividerAddOptimal = dividerAddFracDiv; + diviserOptimal = diviser; + relativeOptimalError = relativeError; + if (relativeError == 0) + break; + } + } /* End of if */ + } /* end of inner for loop */ + if (relativeError == 0) + break; + } /* end of outer for loop */ + + if (relativeOptimalError < ((baudrate * UART_ACCEPTED_BAUDRATE_ERROR)/100)) + { + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->LCR |= UART_LCR_DLAB_EN; + ((LPC_UART1_TypeDef *)UARTx)->/*DLIER.*/DLM = UART_LOAD_DLM(diviserOptimal); + ((LPC_UART1_TypeDef *)UARTx)->/*RBTHDLR.*/DLL = UART_LOAD_DLL(diviserOptimal); + /* Then reset DLAB bit */ + ((LPC_UART1_TypeDef *)UARTx)->LCR &= (~UART_LCR_DLAB_EN) & UART_LCR_BITMASK; + ((LPC_UART1_TypeDef *)UARTx)->FDR = (UART_FDR_MULVAL(mulFracDivOptimal) \ + | UART_FDR_DIVADDVAL(dividerAddOptimal)) & UART_FDR_BITMASK; + } + else + { + UARTx->LCR |= UART_LCR_DLAB_EN; + UARTx->/*DLIER.*/DLM = UART_LOAD_DLM(diviserOptimal); + UARTx->/*RBTHDLR.*/DLL = UART_LOAD_DLL(diviserOptimal); + /* Then reset DLAB bit */ + UARTx->LCR &= (~UART_LCR_DLAB_EN) & UART_LCR_BITMASK; + UARTx->FDR = (UART_FDR_MULVAL(mulFracDivOptimal) \ + | UART_FDR_DIVADDVAL(dividerAddOptimal)) & UART_FDR_BITMASK; + } + errorStatus = SUCCESS; + } + + return errorStatus; +} + +/* End of Private Functions ---------------------------------------------------- */ + + +/* Public Functions ----------------------------------------------------------- */ +/** @addtogroup UART_Public_Functions + * @{ + */ +/* UART Init/DeInit functions -------------------------------------------------*/ +/********************************************************************//** + * @brief Initializes the UARTx peripheral according to the specified + * parameters in the UART_ConfigStruct. + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] UART_ConfigStruct Pointer to a UART_CFG_Type structure +* that contains the configuration information for the +* specified UART peripheral. + * @return None + *********************************************************************/ +void UART_Init(LPC_UART_TypeDef *UARTx, UART_CFG_Type *UART_ConfigStruct) +{ + uint32_t tmp; + + // For debug mode + CHECK_PARAM(PARAM_UARTx(UARTx)); + CHECK_PARAM(PARAM_UART_DATABIT(UART_ConfigStruct->Databits)); + CHECK_PARAM(PARAM_UART_STOPBIT(UART_ConfigStruct->Stopbits)); + CHECK_PARAM(PARAM_UART_PARITY(UART_ConfigStruct->Parity)); + +#ifdef _UART0 + if(UARTx == (LPC_UART_TypeDef *)LPC_UART0) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART0, ENABLE); + } +#endif + +#ifdef _UART1 + if(((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART1, ENABLE); + } +#endif + +#ifdef _UART2 + if(UARTx == LPC_UART2) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART2, ENABLE); + } +#endif + +#ifdef _UART3 + if(UARTx == LPC_UART3) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART3, ENABLE); + } +#endif + + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + /* FIFOs are empty */ + ((LPC_UART1_TypeDef *)UARTx)->/*IIFCR.*/FCR = ( UART_FCR_FIFO_EN \ + | UART_FCR_RX_RS | UART_FCR_TX_RS); + // Disable FIFO + ((LPC_UART1_TypeDef *)UARTx)->/*IIFCR.*/FCR = 0; + + // Dummy reading + while (((LPC_UART1_TypeDef *)UARTx)->LSR & UART_LSR_RDR) + { + tmp = ((LPC_UART1_TypeDef *)UARTx)->/*RBTHDLR.*/RBR; + } + + ((LPC_UART1_TypeDef *)UARTx)->TER = UART_TER_TXEN; + // Wait for current transmit complete + while (!(((LPC_UART1_TypeDef *)UARTx)->LSR & UART_LSR_THRE)); + // Disable Tx + ((LPC_UART1_TypeDef *)UARTx)->TER = 0; + + // Disable interrupt + ((LPC_UART1_TypeDef *)UARTx)->/*DLIER.*/IER = 0; + // Set LCR to default state + ((LPC_UART1_TypeDef *)UARTx)->LCR = 0; + // Set ACR to default state + ((LPC_UART1_TypeDef *)UARTx)->ACR = 0; + // Set Modem Control to default state + ((LPC_UART1_TypeDef *)UARTx)->MCR = 0; + // Set RS485 control to default state + ((LPC_UART1_TypeDef *)UARTx)->RS485CTRL = 0; + // Set RS485 delay timer to default state + ((LPC_UART1_TypeDef *)UARTx)->RS485DLY = 0; + // Set RS485 addr match to default state + ((LPC_UART1_TypeDef *)UARTx)->ADRMATCH = 0; + //Dummy Reading to Clear Status + tmp = ((LPC_UART1_TypeDef *)UARTx)->MSR; + tmp = ((LPC_UART1_TypeDef *)UARTx)->LSR; + } + else + { + /* FIFOs are empty */ + UARTx->/*IIFCR.*/FCR = ( UART_FCR_FIFO_EN | UART_FCR_RX_RS | UART_FCR_TX_RS); + // Disable FIFO + UARTx->/*IIFCR.*/FCR = 0; + + // Dummy reading + while (UARTx->LSR & UART_LSR_RDR) + { + tmp = UARTx->/*RBTHDLR.*/RBR; + } + + UARTx->TER = UART_TER_TXEN; + // Wait for current transmit complete + while (!(UARTx->LSR & UART_LSR_THRE)); + // Disable Tx + UARTx->TER = 0; + + // Disable interrupt + UARTx->/*DLIER.*/IER = 0; + // Set LCR to default state + UARTx->LCR = 0; + // Set ACR to default state + UARTx->ACR = 0; + // Dummy reading + tmp = UARTx->LSR; + } + + if (UARTx == LPC_UART3) + { + // Set IrDA to default state + UARTx->ICR = 0; + } + + // Set Line Control register ---------------------------- + + uart_set_divisors(UARTx, (UART_ConfigStruct->Baud_rate)); + + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + tmp = (((LPC_UART1_TypeDef *)UARTx)->LCR & (UART_LCR_DLAB_EN | UART_LCR_BREAK_EN)) \ + & UART_LCR_BITMASK; + } + else + { + tmp = (UARTx->LCR & (UART_LCR_DLAB_EN | UART_LCR_BREAK_EN)) & UART_LCR_BITMASK; + } + + switch (UART_ConfigStruct->Databits){ + case UART_DATABIT_5: + tmp |= UART_LCR_WLEN5; + break; + case UART_DATABIT_6: + tmp |= UART_LCR_WLEN6; + break; + case UART_DATABIT_7: + tmp |= UART_LCR_WLEN7; + break; + case UART_DATABIT_8: + default: + tmp |= UART_LCR_WLEN8; + break; + } + + if (UART_ConfigStruct->Parity == UART_PARITY_NONE) + { + // Do nothing... + } + else + { + tmp |= UART_LCR_PARITY_EN; + switch (UART_ConfigStruct->Parity) + { + case UART_PARITY_ODD: + tmp |= UART_LCR_PARITY_ODD; + break; + + case UART_PARITY_EVEN: + tmp |= UART_LCR_PARITY_EVEN; + break; + + case UART_PARITY_SP_1: + tmp |= UART_LCR_PARITY_F_1; + break; + + case UART_PARITY_SP_0: + tmp |= UART_LCR_PARITY_F_0; + break; + default: + break; + } + } + + switch (UART_ConfigStruct->Stopbits){ + case UART_STOPBIT_2: + tmp |= UART_LCR_STOPBIT_SEL; + break; + case UART_STOPBIT_1: + default: + // Do no thing + break; + } + + + // Write back to LCR, configure FIFO and Disable Tx + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->LCR = (uint8_t)(tmp & UART_LCR_BITMASK); + } + else + { + UARTx->LCR = (uint8_t)(tmp & UART_LCR_BITMASK); + } +} + +/*********************************************************************//** + * @brief De-initializes the UARTx peripheral registers to their + * default reset values. + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @return None + **********************************************************************/ +void UART_DeInit(LPC_UART_TypeDef* UARTx) +{ + // For debug mode + CHECK_PARAM(PARAM_UARTx(UARTx)); + + UART_TxCmd(UARTx, DISABLE); + +#ifdef _UART0 + if (UARTx == (LPC_UART_TypeDef *)LPC_UART0) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART0, DISABLE); + } +#endif + +#ifdef _UART1 + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART1, DISABLE); + } +#endif + +#ifdef _UART2 + if (UARTx == LPC_UART2) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART2, DISABLE); + } +#endif + +#ifdef _UART3 + if (UARTx == LPC_UART3) + { + /* Set up clock and power for UART module */ + CLKPWR_ConfigPPWR (CLKPWR_PCONP_PCUART3, DISABLE); + } +#endif +} + +/*****************************************************************************//** +* @brief Fills each UART_InitStruct member with its default value: +* - 9600 bps +* - 8-bit data +* - 1 Stopbit +* - None Parity +* @param[in] UART_InitStruct Pointer to a UART_CFG_Type structure +* which will be initialized. +* @return None +*******************************************************************************/ +void UART_ConfigStructInit(UART_CFG_Type *UART_InitStruct) +{ + UART_InitStruct->Baud_rate = 9600; + UART_InitStruct->Databits = UART_DATABIT_8; + UART_InitStruct->Parity = UART_PARITY_NONE; + UART_InitStruct->Stopbits = UART_STOPBIT_1; +} + +/* UART Send/Recieve functions -------------------------------------------------*/ +/*********************************************************************//** + * @brief Transmit a single data through UART peripheral + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] Data Data to transmit (must be 8-bit long) + * @return None + **********************************************************************/ +void UART_SendByte(LPC_UART_TypeDef* UARTx, uint8_t Data) +{ + CHECK_PARAM(PARAM_UARTx(UARTx)); + + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->/*RBTHDLR.*/THR = Data & UART_THR_MASKBIT; + } + else + { + UARTx->/*RBTHDLR.*/THR = Data & UART_THR_MASKBIT; + } + +} + + +/*********************************************************************//** + * @brief Receive a single data from UART peripheral + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @return Data received + **********************************************************************/ +uint8_t UART_ReceiveByte(LPC_UART_TypeDef* UARTx) +{ + CHECK_PARAM(PARAM_UARTx(UARTx)); + + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + return (((LPC_UART1_TypeDef *)UARTx)->/*RBTHDLR.*/RBR & UART_RBR_MASKBIT); + } + else + { + return (UARTx->/*RBTHDLR.*/RBR & UART_RBR_MASKBIT); + } +} + +/*********************************************************************//** + * @brief Send a block of data via UART peripheral + * @param[in] UARTx Selected UART peripheral used to send data, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] txbuf Pointer to Transmit buffer + * @param[in] buflen Length of Transmit buffer + * @param[in] flag Flag used in UART transfer, should be + * NONE_BLOCKING or BLOCKING + * @return Number of bytes sent. + * + * Note: when using UART in BLOCKING mode, a time-out condition is used + * via defined symbol UART_BLOCKING_TIMEOUT. + **********************************************************************/ +uint32_t UART_Send(LPC_UART_TypeDef *UARTx, uint8_t *txbuf, + uint32_t buflen, TRANSFER_BLOCK_Type flag) +{ + uint32_t bToSend, bSent, timeOut, fifo_cnt; + uint8_t *pChar = txbuf; + + bToSend = buflen; + + // blocking mode + if (flag == BLOCKING) { + bSent = 0; + while (bToSend){ + timeOut = UART_BLOCKING_TIMEOUT; + // Wait for THR empty with timeout + while (!(UARTx->LSR & UART_LSR_THRE)) { + if (timeOut == 0) break; + timeOut--; + } + // Time out! + if(timeOut == 0) break; + fifo_cnt = UART_TX_FIFO_SIZE; + while (fifo_cnt && bToSend){ + UART_SendByte(UARTx, (*pChar++)); + fifo_cnt--; + bToSend--; + bSent++; + } + } + } + // None blocking mode + else { + bSent = 0; + while (bToSend) { + if (!(UARTx->LSR & UART_LSR_THRE)){ + break; + } + fifo_cnt = UART_TX_FIFO_SIZE; + while (fifo_cnt && bToSend) { + UART_SendByte(UARTx, (*pChar++)); + bToSend--; + fifo_cnt--; + bSent++; + } + } + } + return bSent; +} + +/*********************************************************************//** + * @brief Receive a block of data via UART peripheral + * @param[in] UARTx Selected UART peripheral used to send data, + * should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[out] rxbuf Pointer to Received buffer + * @param[in] buflen Length of Received buffer + * @param[in] flag Flag mode, should be NONE_BLOCKING or BLOCKING + + * @return Number of bytes received + * + * Note: when using UART in BLOCKING mode, a time-out condition is used + * via defined symbol UART_BLOCKING_TIMEOUT. + **********************************************************************/ +uint32_t UART_Receive(LPC_UART_TypeDef *UARTx, uint8_t *rxbuf, \ + uint32_t buflen, TRANSFER_BLOCK_Type flag) +{ + uint32_t bToRecv, bRecv, timeOut; + uint8_t *pChar = rxbuf; + + bToRecv = buflen; + + // Blocking mode + if (flag == BLOCKING) { + bRecv = 0; + while (bToRecv){ + timeOut = UART_BLOCKING_TIMEOUT; + while (!(UARTx->LSR & UART_LSR_RDR)){ + if (timeOut == 0) break; + timeOut--; + } + // Time out! + if(timeOut == 0) break; + // Get data from the buffer + (*pChar++) = UART_ReceiveByte(UARTx); + bToRecv--; + bRecv++; + } + } + // None blocking mode + else { + bRecv = 0; + while (bToRecv) { + if (!(UARTx->LSR & UART_LSR_RDR)) { + break; + } else { + (*pChar++) = UART_ReceiveByte(UARTx); + bRecv++; + bToRecv--; + } + } + } + return bRecv; +} + +/*********************************************************************//** + * @brief Force BREAK character on UART line, output pin UARTx TXD is + forced to logic 0. + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @return None + **********************************************************************/ +void UART_ForceBreak(LPC_UART_TypeDef* UARTx) +{ + CHECK_PARAM(PARAM_UARTx(UARTx)); + + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->LCR |= UART_LCR_BREAK_EN; + } + else + { + UARTx->LCR |= UART_LCR_BREAK_EN; + } +} + + +/********************************************************************//** + * @brief Enable or disable specified UART interrupt. + * @param[in] UARTx UART peripheral selected, should be + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] UARTIntCfg Specifies the interrupt flag, + * should be one of the following: + - UART_INTCFG_RBR : RBR Interrupt enable + - UART_INTCFG_THRE : THR Interrupt enable + - UART_INTCFG_RLS : RX line status interrupt enable + - UART1_INTCFG_MS : Modem status interrupt enable (UART1 only) + - UART1_INTCFG_CTS : CTS1 signal transition interrupt enable (UART1 only) + - UART_INTCFG_ABEO : Enables the end of auto-baud interrupt + - UART_INTCFG_ABTO : Enables the auto-baud time-out interrupt + * @param[in] NewState New state of specified UART interrupt type, + * should be: + * - ENALBE: Enable this UART interrupt type. +* - DISALBE: Disable this UART interrupt type. + * @return None + *********************************************************************/ +void UART_IntConfig(LPC_UART_TypeDef *UARTx, UART_INT_Type UARTIntCfg, FunctionalState NewState) +{ + uint32_t tmp = 0; + + CHECK_PARAM(PARAM_UARTx(UARTx)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + switch(UARTIntCfg){ + case UART_INTCFG_RBR: + tmp = UART_IER_RBRINT_EN; + break; + case UART_INTCFG_THRE: + tmp = UART_IER_THREINT_EN; + break; + case UART_INTCFG_RLS: + tmp = UART_IER_RLSINT_EN; + break; + case UART1_INTCFG_MS: + tmp = UART1_IER_MSINT_EN; + break; + case UART1_INTCFG_CTS: + tmp = UART1_IER_CTSINT_EN; + break; + case UART_INTCFG_ABEO: + tmp = UART_IER_ABEOINT_EN; + break; + case UART_INTCFG_ABTO: + tmp = UART_IER_ABTOINT_EN; + break; + } + + if ((LPC_UART1_TypeDef *) UARTx == LPC_UART1) + { + CHECK_PARAM((PARAM_UART_INTCFG(UARTIntCfg)) || (PARAM_UART1_INTCFG(UARTIntCfg))); + } + else + { + CHECK_PARAM(PARAM_UART_INTCFG(UARTIntCfg)); + } + + if (NewState == ENABLE) + { + if ((LPC_UART1_TypeDef *) UARTx == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->/*DLIER.*/IER |= tmp; + } + else + { + UARTx->/*DLIER.*/IER |= tmp; + } + } + else + { + if ((LPC_UART1_TypeDef *) UARTx == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->/*DLIER.*/IER &= (~tmp) & UART1_IER_BITMASK; + } + else + { + UARTx->/*DLIER.*/IER &= (~tmp) & UART_IER_BITMASK; + } + } +} + + +/********************************************************************//** + * @brief Get current value of Line Status register in UART peripheral. + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @return Current value of Line Status register in UART peripheral. + * Note: The return value of this function must be ANDed with each member in + * UART_LS_Type enumeration to determine current flag status + * corresponding to each Line status type. Because some flags in + * Line Status register will be cleared after reading, the next reading + * Line Status register could not be correct. So this function used to + * read Line status register in one time only, then the return value + * used to check all flags. + *********************************************************************/ +uint8_t UART_GetLineStatus(LPC_UART_TypeDef* UARTx) +{ + CHECK_PARAM(PARAM_UARTx(UARTx)); + + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + return ((((LPC_UART1_TypeDef *)LPC_UART1)->LSR) & UART_LSR_BITMASK); + } + else + { + return ((UARTx->LSR) & UART_LSR_BITMASK); + } +} + +/********************************************************************//** + * @brief Get Interrupt Identification value + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @return Current value of UART UIIR register in UART peripheral. + *********************************************************************/ +uint32_t UART_GetIntId(LPC_UART_TypeDef* UARTx) +{ + CHECK_PARAM(PARAM_UARTx(UARTx)); + return (UARTx->IIR & 0x03CF); +} + +/*********************************************************************//** + * @brief Check whether if UART is busy or not + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @return RESET if UART is not busy, otherwise return SET. + **********************************************************************/ +FlagStatus UART_CheckBusy(LPC_UART_TypeDef *UARTx) +{ + if (UARTx->LSR & UART_LSR_TEMT){ + return RESET; + } else { + return SET; + } +} + + +/*********************************************************************//** + * @brief Configure FIFO function on selected UART peripheral + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] FIFOCfg Pointer to a UART_FIFO_CFG_Type Structure that + * contains specified information about FIFO configuration + * @return none + **********************************************************************/ +void UART_FIFOConfig(LPC_UART_TypeDef *UARTx, UART_FIFO_CFG_Type *FIFOCfg) +{ + uint8_t tmp = 0; + + CHECK_PARAM(PARAM_UARTx(UARTx)); + CHECK_PARAM(PARAM_UART_FIFO_LEVEL(FIFOCfg->FIFO_Level)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(FIFOCfg->FIFO_DMAMode)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(FIFOCfg->FIFO_ResetRxBuf)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(FIFOCfg->FIFO_ResetTxBuf)); + + tmp |= UART_FCR_FIFO_EN; + switch (FIFOCfg->FIFO_Level){ + case UART_FIFO_TRGLEV0: + tmp |= UART_FCR_TRG_LEV0; + break; + case UART_FIFO_TRGLEV1: + tmp |= UART_FCR_TRG_LEV1; + break; + case UART_FIFO_TRGLEV2: + tmp |= UART_FCR_TRG_LEV2; + break; + case UART_FIFO_TRGLEV3: + default: + tmp |= UART_FCR_TRG_LEV3; + break; + } + + if (FIFOCfg->FIFO_ResetTxBuf == ENABLE) + { + tmp |= UART_FCR_TX_RS; + } + if (FIFOCfg->FIFO_ResetRxBuf == ENABLE) + { + tmp |= UART_FCR_RX_RS; + } + if (FIFOCfg->FIFO_DMAMode == ENABLE) + { + tmp |= UART_FCR_DMAMODE_SEL; + } + + + //write to FIFO control register + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->/*IIFCR.*/FCR = tmp & UART_FCR_BITMASK; + } + else + { + UARTx->/*IIFCR.*/FCR = tmp & UART_FCR_BITMASK; + } +} + +/*****************************************************************************//** +* @brief Fills each UART_FIFOInitStruct member with its default value: +* - FIFO_DMAMode = DISABLE +* - FIFO_Level = UART_FIFO_TRGLEV0 +* - FIFO_ResetRxBuf = ENABLE +* - FIFO_ResetTxBuf = ENABLE +* - FIFO_State = ENABLE + +* @param[in] UART_FIFOInitStruct Pointer to a UART_FIFO_CFG_Type structure +* which will be initialized. +* @return None +*******************************************************************************/ +void UART_FIFOConfigStructInit(UART_FIFO_CFG_Type *UART_FIFOInitStruct) +{ + UART_FIFOInitStruct->FIFO_DMAMode = DISABLE; + UART_FIFOInitStruct->FIFO_Level = UART_FIFO_TRGLEV0; + UART_FIFOInitStruct->FIFO_ResetRxBuf = ENABLE; + UART_FIFOInitStruct->FIFO_ResetTxBuf = ENABLE; +} + + +/*********************************************************************//** + * @brief Start/Stop Auto Baudrate activity + * @param[in] UARTx UART peripheral selected, should be + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] ABConfigStruct A pointer to UART_AB_CFG_Type structure that + * contains specified information about UART + * auto baudrate configuration + * @param[in] NewState New State of Auto baudrate activity, should be: + * - ENABLE: Start this activity + * - DISABLE: Stop this activity + * Note: Auto-baudrate mode enable bit will be cleared once this mode + * completed. + * @return none + **********************************************************************/ +void UART_ABCmd(LPC_UART_TypeDef *UARTx, UART_AB_CFG_Type *ABConfigStruct, \ + FunctionalState NewState) +{ + uint32_t tmp; + + CHECK_PARAM(PARAM_UARTx(UARTx)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + tmp = 0; + if (NewState == ENABLE) { + if (ABConfigStruct->ABMode == UART_AUTOBAUD_MODE1){ + tmp |= UART_ACR_MODE; + } + if (ABConfigStruct->AutoRestart == ENABLE){ + tmp |= UART_ACR_AUTO_RESTART; + } + } + + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + if (NewState == ENABLE) + { + // Clear DLL and DLM value + ((LPC_UART1_TypeDef *)UARTx)->LCR |= UART_LCR_DLAB_EN; + ((LPC_UART1_TypeDef *)UARTx)->DLL = 0; + ((LPC_UART1_TypeDef *)UARTx)->DLM = 0; + ((LPC_UART1_TypeDef *)UARTx)->LCR &= ~UART_LCR_DLAB_EN; + // FDR value must be reset to default value + ((LPC_UART1_TypeDef *)UARTx)->FDR = 0x10; + ((LPC_UART1_TypeDef *)UARTx)->ACR = UART_ACR_START | tmp; + } + else + { + ((LPC_UART1_TypeDef *)UARTx)->ACR = 0; + } + } + else + { + if (NewState == ENABLE) + { + // Clear DLL and DLM value + UARTx->LCR |= UART_LCR_DLAB_EN; + UARTx->DLL = 0; + UARTx->DLM = 0; + UARTx->LCR &= ~UART_LCR_DLAB_EN; + // FDR value must be reset to default value + UARTx->FDR = 0x10; + UARTx->ACR = UART_ACR_START | tmp; + } + else + { + UARTx->ACR = 0; + } + } +} + +/*********************************************************************//** + * @brief Clear Autobaud Interrupt Pending + * @param[in] UARTx UART peripheral selected, should be + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] ABIntType type of auto-baud interrupt, should be: + * - UART_AUTOBAUD_INTSTAT_ABEO: End of Auto-baud interrupt + * - UART_AUTOBAUD_INTSTAT_ABTO: Auto-baud time out interrupt + * @return none + **********************************************************************/ +void UART_ABClearIntPending(LPC_UART_TypeDef *UARTx, UART_ABEO_Type ABIntType) +{ + CHECK_PARAM(PARAM_UARTx(UARTx)); + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + UARTx->ACR |= ABIntType; + } + else + UARTx->ACR |= ABIntType; +} + +/*********************************************************************//** + * @brief Enable/Disable transmission on UART TxD pin + * @param[in] UARTx UART peripheral selected, should be: + * - LPC_UART0: UART0 peripheral + * - LPC_UART1: UART1 peripheral + * - LPC_UART2: UART2 peripheral + * - LPC_UART3: UART3 peripheral + * @param[in] NewState New State of Tx transmission function, should be: + * - ENABLE: Enable this function + - DISABLE: Disable this function + * @return none + **********************************************************************/ +void UART_TxCmd(LPC_UART_TypeDef *UARTx, FunctionalState NewState) +{ + CHECK_PARAM(PARAM_UARTx(UARTx)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + if (NewState == ENABLE) + { + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->TER |= UART_TER_TXEN; + } + else + { + UARTx->TER |= UART_TER_TXEN; + } + } + else + { + if (((LPC_UART1_TypeDef *)UARTx) == LPC_UART1) + { + ((LPC_UART1_TypeDef *)UARTx)->TER &= (~UART_TER_TXEN) & UART_TER_BITMASK; + } + else + { + UARTx->TER &= (~UART_TER_TXEN) & UART_TER_BITMASK; + } + } +} + +/* UART IrDA functions ---------------------------------------------------*/ + +#ifdef _UART3 + +/*********************************************************************//** + * @brief Enable or disable inverting serial input function of IrDA + * on UART peripheral. + * @param[in] UARTx UART peripheral selected, should be LPC_UART3 (only) + * @param[in] NewState New state of inverting serial input, should be: + * - ENABLE: Enable this function. + * - DISABLE: Disable this function. + * @return none + **********************************************************************/ +void UART_IrDAInvtInputCmd(LPC_UART_TypeDef* UARTx, FunctionalState NewState) +{ + CHECK_PARAM(PARAM_UART_IrDA(UARTx)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + if (NewState == ENABLE) + { + UARTx->ICR |= UART_ICR_IRDAINV; + } + else if (NewState == DISABLE) + { + UARTx->ICR &= (~UART_ICR_IRDAINV) & UART_ICR_BITMASK; + } +} + + +/*********************************************************************//** + * @brief Enable or disable IrDA function on UART peripheral. + * @param[in] UARTx UART peripheral selected, should be LPC_UART3 (only) + * @param[in] NewState New state of IrDA function, should be: + * - ENABLE: Enable this function. + * - DISABLE: Disable this function. + * @return none + **********************************************************************/ +void UART_IrDACmd(LPC_UART_TypeDef* UARTx, FunctionalState NewState) +{ + CHECK_PARAM(PARAM_UART_IrDA(UARTx)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + if (NewState == ENABLE) + { + UARTx->ICR |= UART_ICR_IRDAEN; + } + else + { + UARTx->ICR &= (~UART_ICR_IRDAEN) & UART_ICR_BITMASK; + } +} + + +/*********************************************************************//** + * @brief Configure Pulse divider for IrDA function on UART peripheral. + * @param[in] UARTx UART peripheral selected, should be LPC_UART3 (only) + * @param[in] PulseDiv Pulse Divider value from Peripheral clock, + * should be one of the following: + - UART_IrDA_PULSEDIV2 : Pulse width = 2 * Tpclk + - UART_IrDA_PULSEDIV4 : Pulse width = 4 * Tpclk + - UART_IrDA_PULSEDIV8 : Pulse width = 8 * Tpclk + - UART_IrDA_PULSEDIV16 : Pulse width = 16 * Tpclk + - UART_IrDA_PULSEDIV32 : Pulse width = 32 * Tpclk + - UART_IrDA_PULSEDIV64 : Pulse width = 64 * Tpclk + - UART_IrDA_PULSEDIV128 : Pulse width = 128 * Tpclk + - UART_IrDA_PULSEDIV256 : Pulse width = 256 * Tpclk + + * @return none + **********************************************************************/ +void UART_IrDAPulseDivConfig(LPC_UART_TypeDef *UARTx, UART_IrDA_PULSE_Type PulseDiv) +{ + uint32_t tmp, tmp1; + CHECK_PARAM(PARAM_UART_IrDA(UARTx)); + CHECK_PARAM(PARAM_UART_IrDA_PULSEDIV(PulseDiv)); + + tmp1 = UART_ICR_PULSEDIV(PulseDiv); + tmp = UARTx->ICR & (~UART_ICR_PULSEDIV(7)); + tmp |= tmp1 | UART_ICR_FIXPULSE_EN; + UARTx->ICR = tmp & UART_ICR_BITMASK; +} + +#endif + + +/* UART1 FullModem function ---------------------------------------------*/ + +#ifdef _UART1 + +/*********************************************************************//** + * @brief Force pin DTR/RTS corresponding to given state (Full modem mode) + * @param[in] UARTx LPC_UART1 (only) + * @param[in] Pin Pin that NewState will be applied to, should be: + * - UART1_MODEM_PIN_DTR: DTR pin. + * - UART1_MODEM_PIN_RTS: RTS pin. + * @param[in] NewState New State of DTR/RTS pin, should be: + * - INACTIVE: Force the pin to inactive signal. + - ACTIVE: Force the pin to active signal. + * @return none + **********************************************************************/ +void UART_FullModemForcePinState(LPC_UART1_TypeDef *UARTx, UART_MODEM_PIN_Type Pin, \ + UART1_SignalState NewState) +{ + uint8_t tmp = 0; + + CHECK_PARAM(PARAM_UART1_MODEM(UARTx)); + CHECK_PARAM(PARAM_UART1_MODEM_PIN(Pin)); + CHECK_PARAM(PARAM_UART1_SIGNALSTATE(NewState)); + + switch (Pin){ + case UART1_MODEM_PIN_DTR: + tmp = UART1_MCR_DTR_CTRL; + break; + case UART1_MODEM_PIN_RTS: + tmp = UART1_MCR_RTS_CTRL; + break; + default: + break; + } + + if (NewState == ACTIVE){ + UARTx->MCR |= tmp; + } else { + UARTx->MCR &= (~tmp) & UART1_MCR_BITMASK; + } +} + + +/*********************************************************************//** + * @brief Configure Full Modem mode for UART peripheral + * @param[in] UARTx LPC_UART1 (only) + * @param[in] Mode Full Modem mode, should be: + * - UART1_MODEM_MODE_LOOPBACK: Loop back mode. + * - UART1_MODEM_MODE_AUTO_RTS: Auto-RTS mode. + * - UART1_MODEM_MODE_AUTO_CTS: Auto-CTS mode. + * @param[in] NewState New State of this mode, should be: + * - ENABLE: Enable this mode. + - DISABLE: Disable this mode. + * @return none + **********************************************************************/ +void UART_FullModemConfigMode(LPC_UART1_TypeDef *UARTx, UART_MODEM_MODE_Type Mode, \ + FunctionalState NewState) +{ + uint8_t tmp = 0; + + CHECK_PARAM(PARAM_UART1_MODEM(UARTx)); + CHECK_PARAM(PARAM_UART1_MODEM_MODE(Mode)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(NewState)); + + switch(Mode){ + case UART1_MODEM_MODE_LOOPBACK: + tmp = UART1_MCR_LOOPB_EN; + break; + case UART1_MODEM_MODE_AUTO_RTS: + tmp = UART1_MCR_AUTO_RTS_EN; + break; + case UART1_MODEM_MODE_AUTO_CTS: + tmp = UART1_MCR_AUTO_CTS_EN; + break; + default: + break; + } + + if (NewState == ENABLE) + { + UARTx->MCR |= tmp; + } + else + { + UARTx->MCR &= (~tmp) & UART1_MCR_BITMASK; + } +} + + +/*********************************************************************//** + * @brief Get current status of modem status register + * @param[in] UARTx LPC_UART1 (only) + * @return Current value of modem status register + * Note: The return value of this function must be ANDed with each member + * UART_MODEM_STAT_type enumeration to determine current flag status + * corresponding to each modem flag status. Because some flags in + * modem status register will be cleared after reading, the next reading + * modem register could not be correct. So this function used to + * read modem status register in one time only, then the return value + * used to check all flags. + **********************************************************************/ +uint8_t UART_FullModemGetStatus(LPC_UART1_TypeDef *UARTx) +{ + CHECK_PARAM(PARAM_UART1_MODEM(UARTx)); + return ((UARTx->MSR) & UART1_MSR_BITMASK); +} + + +/* UART RS485 functions --------------------------------------------------------------*/ + +/*********************************************************************//** + * @brief Configure UART peripheral in RS485 mode according to the specified +* parameters in the RS485ConfigStruct. + * @param[in] UARTx LPC_UART1 (only) + * @param[in] RS485ConfigStruct Pointer to a UART1_RS485_CTRLCFG_Type structure +* that contains the configuration information for specified UART +* in RS485 mode. + * @return None + **********************************************************************/ +void UART_RS485Config(LPC_UART1_TypeDef *UARTx, UART1_RS485_CTRLCFG_Type *RS485ConfigStruct) +{ + uint32_t tmp; + + CHECK_PARAM(PARAM_UART1_MODEM(UARTx)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(RS485ConfigStruct->AutoAddrDetect_State)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(RS485ConfigStruct->AutoDirCtrl_State)); + CHECK_PARAM(PARAM_UART1_RS485_CFG_DELAYVALUE(RS485ConfigStruct->DelayValue)); + CHECK_PARAM(PARAM_SETSTATE(RS485ConfigStruct->DirCtrlPol_Level)); + CHECK_PARAM(PARAM_UART_RS485_DIRCTRL_PIN(RS485ConfigStruct->DirCtrlPin)); + CHECK_PARAM(PARAM_UART1_RS485_CFG_MATCHADDRVALUE(RS485ConfigStruct->MatchAddrValue)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(RS485ConfigStruct->NormalMultiDropMode_State)); + CHECK_PARAM(PARAM_FUNCTIONALSTATE(RS485ConfigStruct->Rx_State)); + + tmp = 0; + // If Auto Direction Control is enabled - This function is used in Master mode + if (RS485ConfigStruct->AutoDirCtrl_State == ENABLE) + { + tmp |= UART1_RS485CTRL_DCTRL_EN; + + // Set polar + if (RS485ConfigStruct->DirCtrlPol_Level == SET) + { + tmp |= UART1_RS485CTRL_OINV_1; + } + + // Set pin according to + if (RS485ConfigStruct->DirCtrlPin == UART1_RS485_DIRCTRL_DTR) + { + tmp |= UART1_RS485CTRL_SEL_DTR; + } + + // Fill delay time + UARTx->RS485DLY = RS485ConfigStruct->DelayValue & UART1_RS485DLY_BITMASK; + } + + // MultiDrop mode is enable + if (RS485ConfigStruct->NormalMultiDropMode_State == ENABLE) + { + tmp |= UART1_RS485CTRL_NMM_EN; + } + + // Auto Address Detect function + if (RS485ConfigStruct->AutoAddrDetect_State == ENABLE) + { + tmp |= UART1_RS485CTRL_AADEN; + // Fill Match Address + UARTx->ADRMATCH = RS485ConfigStruct->MatchAddrValue & UART1_RS485ADRMATCH_BITMASK; + } + + + // Receiver is disable + if (RS485ConfigStruct->Rx_State == DISABLE) + { + tmp |= UART1_RS485CTRL_RX_DIS; + } + + // write back to RS485 control register + UARTx->RS485CTRL = tmp & UART1_RS485CTRL_BITMASK; + + // Enable Parity function and leave parity in stick '0' parity as default + UARTx->LCR |= (UART_LCR_PARITY_F_0 | UART_LCR_PARITY_EN); +} + +/*********************************************************************//** + * @brief Enable/Disable receiver in RS485 module in UART1 + * @param[in] UARTx LPC_UART1 (only) + * @param[in] NewState New State of command, should be: + * - ENABLE: Enable this function. + * - DISABLE: Disable this function. + * @return None + **********************************************************************/ +void UART_RS485ReceiverCmd(LPC_UART1_TypeDef *UARTx, FunctionalState NewState) +{ + if (NewState == ENABLE){ + UARTx->RS485CTRL &= ~UART1_RS485CTRL_RX_DIS; + } else { + UARTx->RS485CTRL |= UART1_RS485CTRL_RX_DIS; + } +} + +/*********************************************************************//** + * @brief Send data on RS485 bus with specified parity stick value (9-bit mode). + * @param[in] UARTx LPC_UART1 (only) + * @param[in] pDatFrm Pointer to data frame. + * @param[in] size Size of data. + * @param[in] ParityStick Parity Stick value, should be 0 or 1. + * @return None + **********************************************************************/ +uint32_t UART_RS485Send(LPC_UART1_TypeDef *UARTx, uint8_t *pDatFrm, \ + uint32_t size, uint8_t ParityStick) +{ + uint8_t tmp, save; + uint32_t cnt; + + if (ParityStick){ + save = tmp = UARTx->LCR & UART_LCR_BITMASK; + tmp &= ~(UART_LCR_PARITY_EVEN); + UARTx->LCR = tmp; + cnt = UART_Send((LPC_UART_TypeDef *)UARTx, pDatFrm, size, BLOCKING); + while (!(UARTx->LSR & UART_LSR_TEMT)); + UARTx->LCR = save; + } else { + cnt = UART_Send((LPC_UART_TypeDef *)UARTx, pDatFrm, size, BLOCKING); + while (!(UARTx->LSR & UART_LSR_TEMT)); + } + return cnt; +} + +/*********************************************************************//** + * @brief Send Slave address frames on RS485 bus. + * @param[in] UARTx LPC_UART1 (only) + * @param[in] SlvAddr Slave Address. + * @return None + **********************************************************************/ +void UART_RS485SendSlvAddr(LPC_UART1_TypeDef *UARTx, uint8_t SlvAddr) +{ + UART_RS485Send(UARTx, &SlvAddr, 1, 1); +} + +/*********************************************************************//** + * @brief Send Data frames on RS485 bus. + * @param[in] UARTx LPC_UART1 (only) + * @param[in] pData Pointer to data to be sent. + * @param[in] size Size of data frame to be sent. + * @return None + **********************************************************************/ +uint32_t UART_RS485SendData(LPC_UART1_TypeDef *UARTx, uint8_t *pData, uint32_t size) +{ + return (UART_RS485Send(UARTx, pData, size, 0)); +} + +#endif /* _UART1 */ + +#endif /* _UART */ + +/** + * @} + */ + +/** + * @} + */ +/* --------------------------------- End Of File ------------------------------ */ +