yap yee king
lel
Fork of
XBeeLib
by 
Digi International Inc.
Diff: XBeeZB/XBeeZB.h
- Revision:
- 4:629712865107
- Parent:
- 3:8662ebe83570
- Child:
- 6:06522f3a6642
diff -r 8662ebe83570 -r 629712865107 XBeeZB/XBeeZB.h
--- a/XBeeZB/XBeeZB.h Mon May 18 13:16:55 2015 +0200
+++ b/XBeeZB/XBeeZB.h Mon Jun 01 18:59:43 2015 +0200
@@ -44,6 +44,25 @@
SUPPLY_VOLTAGE = 7, /**< SUPPLY_VOLTAGE is not a real pin */
};
+ enum AssocStatus {
+ ErrorReading = -1, /**< Error occurred when reading parameter. */
+ Joined = 0x00, /**< Successfully formed or joined a network. (Coordinators form a network, routers and end devices join a network.) */
+ NoPANs = 0x21, /**< Scan found no PANs */
+ NoValidPAN = 0x22, /**< Scan found no valid PANs based on current SC and ID settings */
+ JoinNotAllowed = 0x23, /**< Valid Coordinator or Routers found, but they are not allowing joining (NJ expired). */
+ NoBeacons = 0x24, /**< No joinable beacons were found. */
+ Unexpected = 0x25, /**< Unexpected state, node should not be attempting to join at this time. */
+ JoinFailed = 0x27, /**< Node Joining attempt failed (typically due to incompatible security settings). */
+ CoordStartFail = 0x2A, /**< Coordinator start attempt failed */
+ CheckingCoord = 0x2B, /**< Checking for an existing coordinator. */
+ LeaveFail = 0x2C, /**< Attempt to leave the network failed. */
+ JoinNoResponse = 0xAB, /**< Attempted to join a device that did not respond. */
+ SecKeyUnsec = 0xAC, /**< Secure join error - network security key received unsecured. */
+ SecKeyNotRec = 0xAD, /**< Secure join error - network security key not received. */
+ SecBadKey = 0xAF, /**< Secure join error - joining device does not have the right preconfigured link key. */
+ Scanning = 0xFF /**< Scanning for a ZigBee network (routers and end devices). */
+ };
+
/** Class constructor
* @param tx the TX pin of the UART that will interface the XBee module
* @param rx the RX pin of the UART that will interface the XBee module
@@ -54,10 +73,10 @@
* to this baud rate (ATBD parameter). By default it is configured to 9600 bps
*/
XBeeZB(PinName tx, PinName rx, PinName reset = NC, PinName rts = NC, PinName cts = NC, int baud = 9600);
-
+
/** Class destructor */
virtual ~XBeeZB();
-
+
/** init- initializes object
* This function must be called just after creating the object so it initializes internal data.
* @returns
@@ -66,7 +85,7 @@
*/
RadioStatus init();
- /** set_panid - sets the 64bit extended PAN ID.
+ /** set_panid - sets the 64bit extended PAN ID.
*
* @note on ZigBee devices, if set to 0, the coordinator will select a random PAN ID
* and the routers will join any extended PAN ID
@@ -76,7 +95,7 @@
* Failure otherwise
*/
RadioStatus set_panid(uint64_t panid);
-
+
/** get_configured_panid - gets the configured PAN ID, as it was set by @ref set_panid().
*
* @note on ZigBee devices, if set to 0, the coordinator will select a random PAN ID
@@ -161,16 +180,7 @@
*/
RadioStatus check_for_coordinator_at_start(bool enable);
- /** enable_network_encryption - Enable network encryption.
- *
- * @param enable whether to enable this feature or not
- * @returns
- * Success if the operation was successful,
- * Failure otherwise
- */
- RadioStatus enable_network_encryption(bool enable);
-
- /** set_encryption_key - Set the 128-bit AES network encryption key. If set to 0 (default), the module will select a random network key.
+ /** set_network_security_key - (Coordinator only) Set the 128-bit AES network encryption key. If set to 0 (default), the module will select a random network key.
* It is not recommended to set the key programmatically, because it could be read through the raw serial port bits.
* @param key pointer to the 128-bit AES key
* @param length size of the buffer pointed by 'key'
@@ -178,17 +188,7 @@
* Success if the operation was successful,
* Failure otherwise
*/
- RadioStatus set_encryption_key(const uint8_t * const key, const uint16_t length);
-
- /** set_tc_link_key - Set the Trust Center 128-bit AES link key. Setting it to 0 will cause the coordinator to transmit the network key in the clear to joining devices, and will cause joining devices to acquire the network key in the clear when joining.
- * It is not recommended to set the key programmatically, because it could be read through the raw serial port bits.
- * @param key pointer to the 128-bit AES key
- * @param length size of the buffer pointed by 'key'
- * @returns
- * Success if the operation was successful,
- * Failure otherwise
- */
- RadioStatus set_tc_link_key(const uint8_t * const key, const uint16_t length);
+ RadioStatus set_network_security_key(const uint8_t * const key, const uint16_t length);
#define XBEE_ZB_ENC_OPT_SEND_KEY_ON_JOIN 0x01
#define XBEE_ZB_ENC_OPT_USE_TRUST_CENTER 0x02
@@ -232,15 +232,8 @@
/** unregister_io_sample_cb - removes the IO Sample Data reception callback */
void unregister_io_sample_cb();
- /** get_network_role - returns the role of this device in the ZigBee network
- *
- * @returns the role of this device
- */
- NetworkRole get_network_role();
- /** */
-
/*********************** send_data member methods ************************/
- /** send_data - sends data to a remote device
+ /** send_data - sends data to a remote device
*
* @param remote remote device
* @param data pointer to the data that will be sent
@@ -250,7 +243,7 @@
* TxStatusSuccess if the operation was successful,
* the error code otherwise
*/
- virtual TxStatus send_data(const RemoteXBee& remote, const uint8_t *const data, uint16_t len, bool syncr = true);
+ virtual TxStatus send_data(const RemoteXBee& remote, const uint8_t *const data, uint16_t len, bool syncr = true);
/** send_data - sends data to a remote device. This method uses
* the explicit addressing frame, allowing to use source and
@@ -268,7 +261,7 @@
* TxStatusSuccess if the operation was successful,
* the error code otherwise
*/
- TxStatus send_data(const RemoteXBee& remote, uint8_t source_ep,
+ TxStatus send_data(const RemoteXBee& remote, uint8_t source_ep,
uint8_t dest_ep, uint16_t cluster_id, uint16_t profile_id,
const uint8_t *const data, uint16_t len, bool syncr = true);
@@ -283,11 +276,17 @@
*/
TxStatus send_data_to_coordinator(const uint8_t *const data, uint16_t len, bool syncr = true);
+ /** get_assoc_status - returns current network association status. This wraps AI parameter, for more information refer to moudle's Reference Manual.
+ *
+ * @returns an AssocStatus with current network association status.
+ */
+ AssocStatus get_assoc_status(void);
+
/** is_joined - checks if the device is joined to ZigBee network
* @returns true if joined, false otherwise
*/
bool is_joined();
-
+
/** get_remote_node_by_id - searches for a device in the network with the specified Node Identifier.
*
* @param node_id node id of the device we are looking for
@@ -307,17 +306,17 @@
* @returns the command response status.
*/
virtual AtCmdFrame::AtCmdResp set_param(const RemoteXBee& remote, const char * const param, uint32_t data);
-
+
/** set_param - sets a parameter in a remote radio by sending an AT command and waiting for the response.
*
* @param remote remote device
* @param param parameter to be set.
- * @param data the parameter value byte array (len bytes) to be set.
+ * @param data the parameter value byte array (len bytes) to be set.
* @param len number of bytes of the parameter value.
* @returns the command response status.
*/
virtual AtCmdFrame::AtCmdResp set_param(const RemoteXBee& remote, const char * const param, const uint8_t * data = NULL, uint16_t len = 0);
-
+
/* Allow using XBee::get_param() methods for local radio from this class */
using XBee::get_param;
@@ -325,17 +324,17 @@
*
* @param remote remote device
* @param param parameter to be get.
- * @param data pointer where the param value (4 bytes) will be stored.
+ * @param data pointer where the param value (4 bytes) will be stored.
* @returns the command response status.
*/
virtual AtCmdFrame::AtCmdResp get_param(const RemoteXBee& remote, const char * const param, uint32_t * const data);
-
+
/** get_param - gets a parameter from a remote radio by sending an AT command and waiting for the response.
*
* @param remote remote device
* @param param parameter to be get.
- * @param data pointer where the param value (n bytes) will be stored.
- * @param len pointer where the number of bytes of the param value will be stored.
+ * @param data pointer where the param value (n bytes) will be stored.
+ * @param len pointer where the number of bytes of the param value will be stored.
* @returns the command response status.
*/
virtual AtCmdFrame::AtCmdResp get_param(const RemoteXBee& remote, const char * const param, uint8_t * const data, uint16_t * const len);
@@ -427,18 +426,6 @@
RadioStatus enable_dio_change_detection(const RemoteXBee& remote, IoLine line, bool enable);
protected:
- /** Role of this device in the ZigBee network (coord, router or end device) */
- NetworkRole _nw_role;
-
- /** Indicates if the device is joined to a network. This variable is automatically updated
- * by the library. If the device is acting as coordinator, its value its true */
- volatile bool _joined_network;
-
- /** Vcc exceeded counter, automatically updated by the library */
- volatile uint16_t _vcc_exceeded_cnt;
-
- /* TODO, add setter/getter */
- uint8_t _broadcast_radious;
/** Frame handler used for the node discovery. Registered when a callback function
* is registered */
@@ -447,12 +434,12 @@
/** Frame handler used for the rx packets. Automatically registered when a callback
* function is registered */
FH_RxPacketZB *_rx_pkt_handler;
-
+
/** Frame handler used for the IO Data Sample packets. Automatically registered when a callback
* function is registered */
FH_IoDataSampeZB *_io_data_handler;
- /** Method called directly by the library when a modem status frame is received to
+ /** Method called directly by the library when a modem status frame is received to
* update the internal status variables */
virtual void radio_status_update(AtCmdFrame::ModemStatus modem_status);