Diff: main.cpp

Revision:

5:8a3cf73d7ed3

Parent:

3:4cd9171ba989

diff -r e5018e5ba340 -r 8a3cf73d7ed3 main.cpp
--- a/main.cpp	Thu Jun 16 08:12:33 2016 +0000
+++ b/main.cpp	Tue Jan 26 08:23:29 2021 +0000
@@ -1,95 +1,45 @@
 #include "mbed.h"
-
-#include "Config.h"
-#include "MicroduinoPinNames.h"
-DigitalOut myled(P0_20);
-I2C g_i2c(P0_11, P0_10);//SDA, SCL
 #include "SimpleTimer.h"
-#include "userDef.h"
-#include "sensor.h"
-#ifdef OPEN_OLED
-#include "oled.h"
-#endif
+extern Serial pc;
 #include "WiFiBlynk.h"
 
-Serial pc(P0_4, P0_0); // tx, rx
+Serial pc(SERIAL_TX, SERIAL_RX); // tx, rx
 Timer g_Timer;
-Ticker g_Ticker;
-
-void led_flash()
-{
-    static int count = 0;
-    count++;
-    //pc.printf("count : %d, ms : %d\r\n", count, g_Timer.read_ms());
-    myled = 1;
-    wait_ms(70);
-    myled = 0;
-}
+DigitalOut myled(PB_3);
 
-static void led_flash_fast()
-{
-    myled = !myled;
-}
+char SSID[] = "OPPO A7";
+char PASS[] = "12345678";
 
-#ifdef OPEN_OLED
-Adafruit_SSD1306_I2c adaf(g_i2c, P0_13, 0x78, 64, 128);
-void update_oled()
-{
-    myled = 1;
-    wait_ms(70);
-    myled = 0;
-    oled(adaf, sensor_tem, sensor_hum, sensor_light, sensorPM25, Sensor_etoh);
-}
-#endif
+char auth[] = "jx8SAPsgpzJ3pJPzI-q6ZhQIo1F4J7ki";
+
 
 int main()
 {
-    g_Ticker.attach_us(led_flash_fast, 30000);
-    pc.baud(115200);
+    pc.baud(9600);
     pc.printf("Enter main()\r\n");
     //myled = 1;
     g_Timer.start();
     SimpleTimer gSimpleTimer(g_Timer);
 
-    /*
-     * Set ESP8266 baud rate
-     * 在LPC824上，波特率设为115200时，ESP8266是无法工作
-     */
     EspSerial.baud(9600);
-
+    delay(10);
+    
     Blynk.begin(auth, wifi, SSID, PASS);
-    wait(5.0);
-    g_Ticker.detach();
-    
+   
     // Setup a function to be called every second
-    gSimpleTimer.setInterval(2000L, senTempHumi);
-    gSimpleTimer.setInterval(1000, updateLight);
-    gSimpleTimer.setInterval(5000, updateCH4);
-    gSimpleTimer.setInterval(4000, updateTempHumi);
+
     //gSimpleTimer.setInterval(3000, PM25);
-    gSimpleTimer.setInterval(4000, led_flash);
-#ifdef OPEN_OLED
-    gSimpleTimer.setInterval(1000, update_oled);
-#endif
-    //PM25_init();
-    wait_ms(2000);
-#ifdef OPEN_OLED
-    oled_init(adaf);
-#endif
+    
+    
     int pretime = g_Timer.read_ms();
+    
+    
     while(1) {
         //pc.printf("Enter while(1)\r\n");
         //myled = !myled;
         Blynk.run(); // All the Blynk Magic happens here...
         gSimpleTimer.run();
-#if 0
-        int curtime = g_Timer.read_ms();
-        if (curtime - pretime > 4000) {
-            //updateTempHumi();
-            led_flash();
-            pretime = curtime;
-        }
-#endif
+        
 
     }
 }