Diff: main.cpp

Revision:

3:4cd9171ba989

Parent:

2:6cd3b0947188

Child:

5:8a3cf73d7ed3

--- a/main.cpp	Wed Jun 15 03:08:40 2016 +0000
+++ b/main.cpp	Thu Jun 16 08:08:30 2016 +0000
@@ -1,30 +1,37 @@
 #include "mbed.h"
 
+#include "Config.h"
 #include "MicroduinoPinNames.h"
 DigitalOut myled(P0_20);
 I2C g_i2c(P0_11, P0_10);//SDA, SCL
-#if 1
 #include "SimpleTimer.h"
 #include "userDef.h"
 #include "sensor.h"
+#ifdef OPEN_OLED
 #include "oled.h"
 #endif
-//#include "WiFiBlynk.h"
+#include "WiFiBlynk.h"
 
-//Serial pc(P0_4, P0_0); // tx, rx
-
+Serial pc(P0_4, P0_0); // tx, rx
 Timer g_Timer;
+Ticker g_Ticker;
 
 void led_flash()
 {
     static int count = 0;
     count++;
     //pc.printf("count : %d, ms : %d\r\n", count, g_Timer.read_ms());
-    //myled = 1;
+    myled = 1;
     wait_ms(70);
     myled = 0;
 }
 
+static void led_flash_fast()
+{
+    myled = !myled;
+}
+
+#ifdef OPEN_OLED
 Adafruit_SSD1306_I2c adaf(g_i2c, P0_13, 0x78, 64, 128);
 void update_oled()
 {
@@ -33,46 +40,56 @@
     myled = 0;
     oled(adaf, sensor_tem, sensor_hum, sensor_light, sensorPM25, Sensor_etoh);
 }
+#endif
 
 int main()
 {
-    //pc.baud(9600);
+    g_Ticker.attach_us(led_flash_fast, 30000);
+    pc.baud(115200);
+    pc.printf("Enter main()\r\n");
     //myled = 1;
     g_Timer.start();
     SimpleTimer gSimpleTimer(g_Timer);
-    
-    //Serial.begin(9600); // See the connection status in Serial Monitor
-    // Set ESP8266 baud rate
-    //EspSerial.begin(115200);
+
+    /*
+     * Set ESP8266 baud rate
+     * 在LPC824上，波特率设为115200时，ESP8266是无法工作
+     */
+    EspSerial.baud(9600);
 
-    //Blynk.begin(auth, wifi, SSID, PASS);
-
+    Blynk.begin(auth, wifi, SSID, PASS);
+    wait(5.0);
+    g_Ticker.detach();
+    
     // Setup a function to be called every second
-    //gSimpleTimer.setInterval(2000L, senTempHumi);
+    gSimpleTimer.setInterval(2000L, senTempHumi);
     gSimpleTimer.setInterval(1000, updateLight);
     gSimpleTimer.setInterval(5000, updateCH4);
     gSimpleTimer.setInterval(4000, updateTempHumi);
     //gSimpleTimer.setInterval(3000, PM25);
-    //gSimpleTimer.setInterval(4000, led_flash);
+    gSimpleTimer.setInterval(4000, led_flash);
+#ifdef OPEN_OLED
     gSimpleTimer.setInterval(1000, update_oled);
-    
+#endif
     //PM25_init();
     wait_ms(2000);
+#ifdef OPEN_OLED
     oled_init(adaf);
+#endif
     int pretime = g_Timer.read_ms();
     while(1) {
         //pc.printf("Enter while(1)\r\n");
         //myled = !myled;
-        //Blynk.run(); // All the Blynk Magic happens here...
+        Blynk.run(); // All the Blynk Magic happens here...
         gSimpleTimer.run();
-        #if 0
+#if 0
         int curtime = g_Timer.read_ms();
         if (curtime - pretime > 4000) {
             //updateTempHumi();
             led_flash();
             pretime = curtime;
         }
-        #endif
-        
+#endif
+
     }
 }