cc y
ads1115 only
Fork of
mbed
by 
mbed official
Diff: TARGET_UBLOX_C027/PinNames.h
- Revision:
- 77:869cf507173a
- Child:
- 81:7d30d6019079
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_UBLOX_C027/PinNames.h Fri Feb 14 14:36:43 2014 +0000
@@ -0,0 +1,188 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2013 ARM Limited
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+#ifndef MBED_PINNAMES_H
+#define MBED_PINNAMES_H
+
+#include "cmsis.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+ PIN_INPUT,
+ PIN_OUTPUT
+} PinDirection;
+
+#define PORT_SHIFT 5
+
+typedef enum {
+ // LPC Pin Names
+ P0_0 = LPC_GPIO0_BASE,
+ P0_1, P0_2, P0_3, P0_4, P0_5, P0_6, P0_7, P0_8, P0_9, P0_10, P0_11, P0_12, P0_13, P0_14, P0_15, P0_16, P0_17, P0_18, P0_19, P0_20, P0_21, P0_22, P0_23, P0_24, P0_25, P0_26, P0_27, P0_28, P0_29, P0_30, P0_31,
+ P1_0, P1_1, P1_2, P1_3, P1_4, P1_5, P1_6, P1_7, P1_8, P1_9, P1_10, P1_11, P1_12, P1_13, P1_14, P1_15, P1_16, P1_17, P1_18, P1_19, P1_20, P1_21, P1_22, P1_23, P1_24, P1_25, P1_26, P1_27, P1_28, P1_29, P1_30, P1_31,
+ P2_0, P2_1, P2_2, P2_3, P2_4, P2_5, P2_6, P2_7, P2_8, P2_9, P2_10, P2_11, P2_12, P2_13, P2_14, P2_15, P2_16, P2_17, P2_18, P2_19, P2_20, P2_21, P2_22, P2_23, P2_24, P2_25, P2_26, P2_27, P2_28, P2_29, P2_30, P2_31,
+ P3_0, P3_1, P3_2, P3_3, P3_4, P3_5, P3_6, P3_7, P3_8, P3_9, P3_10, P3_11, P3_12, P3_13, P3_14, P3_15, P3_16, P3_17, P3_18, P3_19, P3_20, P3_21, P3_22, P3_23, P3_24, P3_25, P3_26, P3_27, P3_28, P3_29, P3_30, P3_31,
+ P4_0, P4_1, P4_2, P4_3, P4_4, P4_5, P4_6, P4_7, P4_8, P4_9, P4_10, P4_11, P4_12, P4_13, P4_14, P4_15, P4_16, P4_17, P4_18, P4_19, P4_20, P4_21, P4_22, P4_23, P4_24, P4_25, P4_26, P4_27, P4_28, P4_29, P4_30, P4_31,
+
+ // Arduino Pin Names
+
+ // PIN header connector
+ // for standard-based form factor with expansion board
+ // -----------------------------------------------------------
+ // PMW = Pulswidth Modulator
+ // EINT = External Interrupt
+ // AOUT = Analog Output
+
+ // Analog Ports (A0-A5)
+ A0 = P0_23, // I2S_CLK
+ A1 = P0_24, // I2S_WS
+ A2 = P0_25, // I2S_SDA
+ A3 = P0_26, // AOUT
+ A4 = P1_30, //
+ A5 = P1_31, //
+ // Digital Port (D0-D7)
+ D0 = P4_29, // TXD
+ D1 = P4_28, // RXD
+ D2 = P2_13, // EINT
+ D3 = P2_0, // PWM
+ D4 = P2_12, // EINT
+ D5 = P2_1, // PWM
+ D6 = P2_2, // PWM
+ D7 = P2_11, // EINT
+ // Digital Port (D8-D13)
+ D8 = P2_4, // PWM
+ D9 = P2_3, // PWM
+ D10 = P1_21, // PWM SSEL
+ D11 = P1_24, // PWM MOSI
+ D12 = P1_23, // PWM MISO
+ D13 = P1_20, // PWM SCK
+ // GND
+ // AREF
+ SDA = P0_0,
+ D14 = SDA,
+ SCL = P0_1,
+ D15 = SCL,
+
+ // I2C (shared with LISA/SARA)
+ GPSSDA = P0_27,
+ GPSSCL = P0_28,
+ // UART
+ GPSTXD = P0_10,
+ GPSRXD = P0_11,
+ // Control
+ GPSRST = P1_18, // Reset (input to GPS, active low)
+ GPSPPS = P1_19, // 1PPS Timepulse (output from GPS)
+ GPSINT = P1_22, // Interrupt (input to GPS)
+ GPSEN = P1_29, // Supply Control (high = enabled)
+
+ // u-blox LISA/SARA cellular modem
+ // http://www.u-blox.com/wireless-modules.html
+ // -----------------------------------------------------------
+ // UART (LPC1768 = DTE, LISA/SARA = DCE)
+ MDMTXD = P0_15, // Transmit Data
+ MDMRXD = P0_16, // Receive Data
+ MDMCTS = P0_17, // Clear to Send
+ MDMDCD = P0_18, // Data Carrier Detect
+ MDMDSR = P0_19, // Data Set Ready
+ MDMDTR = P0_20, // Data Terminal Ready (set high or use handshake)
+ MDMRI = P0_21, // Ring Indicator
+ MDMRTS = P0_22, // Request to Send (set high or use handshake)
+
+ // USB (not available on C27-G35)
+ MDMUSBDP = P0_29, // USB D+
+ MDMUSBDN = P0_30, // USB D-
+ MDMUSBCON = P2_9, // USB Connect
+ MDMUSBDET = P0_7, // USB Detect (n/a on REV.A board)
+ // Control
+ MDMEN = P2_5, // Supply Control (high = enabled)
+ MDMPWRON = P2_6, //
+ MDMGPIO1 = P2_7, // GPIO1, Network status
+ MDMRST = P2_8, // Reset (active low, set as open drain!)
+ MDMLVLOE = P0_9, // Serial/GPIO Level Shifter Output Enable (n/a on REV.A board)
+ MDMILVLOE = P0_8, // I2C Level Shifter Output Enable (n/a on REV.A board)
+
+ // CAN (TJA1040)
+ // -----------------------------------------------------------
+ CANRD = P0_4,
+ CANTD = P0_5,
+ CANS = P0_6, // standby (low=normal, high=standby/rxonly)
+
+ // Ethernet (DP83848)
+ // -----------------------------------------------------------
+ ETHTXD0 = P1_0,
+ ETHTXD1 = P1_1,
+ ETHTXEN = P1_4,
+ ETHCRS = P1_8,
+ ETHRXD0 = P1_9,
+ ETHRXD1 = P1_10,
+ ETHRXEN = P1_14,
+ ETHREFCLK = P1_15,
+ ETHMDC = P1_16,
+ ETHMDIO = P1_17,
+ ETHOSCEN = P1_27,
+ ETHRST = P1_28,
+ ETHLINK = P1_25, // LED_LINK
+ ETHSPEED = P1_26, // LED_SPEED
+
+ // ISP port
+ // -----------------------------------------------------------
+ ISP = P2_10,
+
+ // Other mbed Pin Names
+ LED = P3_25,
+ LED1 = LED,
+ LED_RED = LED,
+
+ // mbed / debug IF (LPC11)
+ // -----------------------------------------------------------
+ // Serial Port
+ USBTX = P0_2,
+ USBRX = P0_3,
+ USBTXD = USBTX, // identical USBTX
+ USBRXD = USBRX, // identical USBRX
+
+ // Not connected
+ NC = (int)0xFFFFFFFF
+} PinName;
+
+typedef enum {
+ PullUp = 0,
+ PullDown = 3,
+ PullNone = 2,
+ OpenDrain = 4
+} PinMode;
+
+// version of PINCON_TypeDef using register arrays
+typedef struct {
+ __IO uint32_t PINSEL[11];
+ uint32_t RESERVED0[5];
+ __IO uint32_t PINMODE[10];
+ __IO uint32_t PINMODE_OD[5];
+} PINCONARRAY_TypeDef;
+
+#define PINCONARRAY ((PINCONARRAY_TypeDef *)LPC_PINCON_BASE)
+
+//Additional C027 stuff
+#define GPSADR (66<<1) // GPS I2C Address
+#define GPSBAUD 9600 // Default GPS Baud Rate
+#define MDMBAUD 115200 // Default Modem Baud Rate
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif