![](/media/cache/img/default_profile.jpg.50x50_q85.jpg)
Color Oled(SSD1331) connect to STMicroelectronics Nucleo-F466
mbed-os/targets/TARGET_NUVOTON/TARGET_M2351/device/Reg/ecap_reg.h
- Committer:
- kadonotakashi
- Date:
- 2018-10-11
- Revision:
- 3:f3764f852aa8
- Parent:
- 0:8fdf9a60065b
File content as of revision 3:f3764f852aa8:
/**************************************************************************//** * @file ecap_reg.h * @version V1.00 * @brief ECAP register definition header file * * @copyright (C) 2017 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #ifndef __ECAP_REG_H__ #define __ECAP_REG_H__ /*---------------------- Enhanced Input Capture Timer -------------------------*/ /** @addtogroup ECAP Enhanced Input Capture Timer(ECAP) Memory Mapped Structure for ECAP Controller @{ */ typedef struct { /** * @var ECAP_T::CNT * Offset: 0x00 Input Capture Counter (24-bit up counter) * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[23:0] |CNT |Input Capture Timer/Counter * | | |The input Capture Timer/Counter is a 24-bit up-counting counter * | | |The clock source for the counter is from the clock divider * @var ECAP_T::HLD0 * Offset: 0x04 Input Capture Hold Register 0 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[23:0] |HOLD |Input Capture Counter Hold Register * | | |When an active input capture channel detects a valid edge signal change, the ECAPCNT value is latched into the corresponding holding register * | | |Each input channel has its own holding register named by ECAP_HLDx where x is from 0 to 2 to indicate inputs from IC0 to IC2, respectively. * @var ECAP_T::HLD1 * Offset: 0x08 Input Capture Hold Register 1 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[23:0] |HOLD |Input Capture Counter Hold Register * | | |When an active input capture channel detects a valid edge signal change, the ECAPCNT value is latched into the corresponding holding register * | | |Each input channel has its own holding register named by ECAP_HLDx where x is from 0 to 2 to indicate inputs from IC0 to IC2, respectively. * @var ECAP_T::HLD2 * Offset: 0x0C Input Capture Hold Register 2 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[23:0] |HOLD |Input Capture Counter Hold Register * | | |When an active input capture channel detects a valid edge signal change, the ECAPCNT value is latched into the corresponding holding register * | | |Each input channel has its own holding register named by ECAP_HLDx where x is from 0 to 2 to indicate inputs from IC0 to IC2, respectively. * @var ECAP_T::CNTCMP * Offset: 0x10 Input Capture Compare Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[23:0] |CNTCMP |Input Capture Counter Compare Register * | | |If the compare function is enabled (CMPEN = 1), this register (ECAP_CNTCMP) is used to compare with the capture counter (ECAP_CNT). * | | |If the reload control is enabled (RLDEN[n] = 1, n=0~3), an overflow event or capture events will trigger the hardware to load the value of this register (ECAP_CNTCMP) into ECAP_CNT. * @var ECAP_T::CTL0 * Offset: 0x14 Input Capture Control Register 0 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[2:0] |NFCLKSEL |Noise Filter Clock Pre-divide Selection * | | |To determine the sampling frequency of the Noise Filter clock * | | |000 = CAP_CLK. * | | |001 = CAP_CLK/2. * | | |010 = CAP_CLK/4. * | | |011 = CAP_CLK/16. * | | |100 = CAP_CLK/32. * | | |101 = CAP_CLK/64. * |[3] |CAPNFDIS |Input Capture Noise Filter Disable Control * | | |0 = Noise filter of Input Capture Enabled. * | | |1 = Noise filter of Input Capture Disabled (Bypass). * |[4] |IC0EN |Port Pin IC0 Input to Input Capture Unit Enable Control * | | |0 = IC0 input to Input Capture Unit Disabled. * | | |1 = IC0 input to Input Capture Unit Enabled. * |[5] |IC1EN |Port Pin IC1 Input to Input Capture Unit Enable Control * | | |0 = IC1 input to Input Capture Unit Disabled. * | | |1 = IC1 input to Input Capture Unit Enabled. * |[6] |IC2EN |Port Pin IC2 Input to Input Capture Unit Enable Control * | | |0 = IC2 input to Input Capture Unit Disabled. * | | |1 = IC2 input to Input Capture Unit Enabled. * |[9:8] |CAPSEL0 |CAP0 Input Source Selection * | | |00 = CAP0 input is from port pin ICAP0. * | | |01 = Reserved. * | | |10 = CAP0 input is from signal CHA of QEI controller unit n. * | | |11 = Reserved. * | | |Note: Input capture unit n matches QEIn, where n = 0~1. * |[11:10] |CAPSEL1 |CAP1 Input Source Selection * | | |00 = CAP1 input is from port pin ICAP1. * | | |01 = Reserved. * | | |10 = CAP1 input is from signal CHB of QEI controller unit n. * | | |11 = Reserved. * | | |Note: Input capture unit n matches QEIn, where n = 0~1. * |[13:12] |CAPSEL2 |CAP2 Input Source Selection * | | |00 = CAP2 input is from port pin ICAP2. * | | |01 = Reserved. * | | |10 = CAP2 input is from signal CHX of QEI controller unit n. * | | |11 = Reserved. * | | |Note: Input capture unit n matches QEIn, where n = 0~1. * |[16] |CAPIEN0 |Input Capture Channel 0 Interrupt Enable Control * | | |0 = The flag CAPTF0 can trigger Input Capture interrupt Disabled. * | | |1 = The flag CAPTF0 can trigger Input Capture interrupt Enabled. * |[17] |CAPIEN1 |Input Capture Channel 1 Interrupt Enable Control * | | |0 = The flag CAPTF1 can trigger Input Capture interrupt Disabled. * | | |1 = The flag CAPTF1 can trigger Input Capture interrupt Enabled. * |[18] |CAPIEN2 |Input Capture Channel 2 Interrupt Enable Control * | | |0 = The flag CAPTF2 can trigger Input Capture interrupt Disabled. * | | |1 = The flag CAPTF2 can trigger Input Capture interrupt Enabled. * |[20] |OVIEN |CAPOVF Trigger Input Capture Interrupt Enable Control * | | |0 = The flag CAPOVF can trigger Input Capture interrupt Disabled. * | | |1 = The flag CAPOVF can trigger Input Capture interrupt Enabled. * |[21] |CMPIEN |CAPCMPF Trigger Input Capture Interrupt Enable Control * | | |0 = The flag CAPCMPF can trigger Input Capture interrupt Disabled. * | | |1 = The flag CAPCMPF can trigger Input Capture interrupt Enabled. * |[24] |CNTEN |Input Capture Counter Start Counting Control * | | |Setting this bit to 1, the capture counter (ECAP_CNT) starts up-counting synchronously with the clock from the . * | | |0 = ECAP_CNT stop counting. * | | |1 = ECAP_CNT starts up-counting. * |[25] |CMPCLREN |Input Capture Counter Cleared by Compare-match Control * | | |If this bit is set to 1, the capture counter (ECAP_CNT) will be cleared to 0 when the compare-match event (CAPCMPF = 1) occurs. * | | |0 = Compare-match event (CAPCMPF) can clear capture counter (ECAP_CNT) Disabled. * | | |1 = Compare-match event (CAPCMPF) can clear capture counter (ECAP_CNT) Enabled. * |[28] |CMPEN |Compare Function Enable Control * | | |The compare function in input capture timer/counter is to compare the dynamic counting ECAP_CNT with the compare register ECAP_CNTCMP, if ECAP_CNT value reaches ECAP_CNTCMP, the flag CAPCMPF will be set. * | | |0 = The compare function Disabled. * | | |1 = The compare function Enabled. * |[29] |CAPEN |Input Capture Timer/Counter Enable Control * | | |0 = Input Capture function Disabled. * | | |1 = Input Capture function Enabled. * @var ECAP_T::CTL1 * Offset: 0x18 Input Capture Control Register 1 * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[1:0] |EDGESEL0 |Channel 0 Captured Edge Selection * | | |Input capture0 can detect falling edge change only, rising edge change only or both edge change * | | |00 = Detect rising edge only. * | | |01 = Detect falling edge only. * | | |1x = Detect both rising and falling edge. * |[3:2] |EDGESEL1 |Channel 1 Captured Edge Selection * | | |Input capture1 can detect falling edge change only, rising edge change only or both edge change * | | |00 = Detect rising edge only. * | | |01 = Detect falling edge only. * | | |1x = Detect both rising and falling edge. * |[5:4] |EDGESEL2 |Channel 2 Captured Edge Selection * | | |Input capture2 can detect falling edge change only, rising edge change only or both edge changes * | | |00 = Detect rising edge only. * | | |01 = Detect falling edge only. * | | |1x = Detect both rising and falling edge. * |[8] |CAP0RLDEN |Capture Counteru2019s Reload Function Triggered by Event CAPTE0 Enable Bit * | | |0 = The reload triggered by Event CAPTE0 Disabled. * | | |1 = The reload triggered by Event CAPTE0 Enabled. * |[9] |CAP1RLDEN |Capture Counteru2019s Reload Function Triggered by Event CAPTE1 Enable Bit * | | |0 = The reload triggered by Event CAPTE1 Disabled. * | | |1 = The reload triggered by Event CAPTE1 Enabled. * |[10] |CAP2RLDEN |Capture Counteru2019s Reload Function Triggered by Event CAPTE2 Enable Bit * | | |0 = The reload triggered by Event CAPTE2 Disabled. * | | |1 = The reload triggered by Event CAPTE2 Enabled. * |[11] |OVRLDEN |Capture Counteru2019s Reload Function Triggered by Overflow Enable Bit * | | |0 = The reload triggered by CAPOV Disabled. * | | |1 = The reload triggered by CAPOV Enabled. * |[14:12] |CLKSEL |Capture Timer Clock Divide Selection * | | |The capture timer clock has a pre-divider with eight divided options controlled by CLKSEL[2:0]. * | | |000 = CAP_CLK/1. * | | |001 = CAP_CLK/4. * | | |010 = CAP_CLK/16. * | | |011 = CAP_CLK/32. * | | |100 = CAP_CLK/64. * | | |101 = CAP_CLK/96. * | | |110 = CAP_CLK/112. * | | |111 = CAP_CLK/128. * |[17:16] |CNTSRCSEL |Capture Timer/Counter Clock Source Selection * | | |Select the capture timer/counter clock source. * | | |00 = CAP_CLK (default). * | | |01 = CAP0. * | | |10 = CAP1. * | | |11 = CAP2. * |[20] |CAP0CLREN |Capture Counter Cleared by Capture Event0 Control * | | |0 = Event CAPTE0 can clear capture counter (ECAP_CNT) Disabled. * | | |1 = Event CAPTE0 can clear capture counter (ECAP_CNT) Enabled. * |[21] |CAP1CLREN |Capture Counter Cleared by Capture Event1 Control * | | |0 = Event CAPTE1 can clear capture counter (ECAP_CNT) Disabled. * | | |1 = Event CAPTE1 can clear capture counter (ECAP_CNT) Enabled. * |[22] |CAP2CLREN |Capture Counter Cleared by Capture Event2 Control * | | |0 = Event CAPTE2 can clear capture counter (ECAP_CNT) Disabled. * | | |1 = Event CAPTE2 can clear capture counter (ECAP_CNT) Enabled. * @var ECAP_T::STATUS * Offset: 0x1C Input Capture Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |CAPTF0 |Input Capture Channel 0 Triggered Flag * | | |When the input capture channel 0 detects a valid edge change at CAP0 input, it will set flag CAPTF0 to high. * | | |0 = No valid edge change has been detected at CAP0 input since last clear. * | | |1 = At least a valid edge change has been detected at CAP0 input since last clear. * | | |Note: This bit is only cleared by writing 1 to it. * |[1] |CAPTF1 |Input Capture Channel 1 Triggered Flag * | | |When the input capture channel 1 detects a valid edge change at CAP1 input, it will set flag CAPTF1 to high. * | | |0 = No valid edge change has been detected at CAP1 input since last clear. * | | |1 = At least a valid edge change has been detected at CAP1 input since last clear. * | | |Note: This bit is only cleared by writing 1 to it. * |[2] |CAPTF2 |Input Capture Channel 2 Triggered Flag * | | |When the input capture channel 2 detects a valid edge change at CAP2 input, it will set flag CAPTF2 to high. * | | |0 = No valid edge change has been detected at CAP2 input since last clear. * | | |1 = At least a valid edge change has been detected at CAP2 input since last clear. * | | |Note: This bit is only cleared by writing 1 to it. * |[4] |CAPCMPF |Input Capture Compare-match Flag * | | |If the input capture compare function is enabled, the flag is set by hardware when capture counter (ECAP_CNT) up counts and reaches the ECAP_CNTCMP value. * | | |0 = ECAP_CNT has not matched ECAP_CNTCMP value since last clear. * | | |1 = ECAP_CNT has matched ECAP_CNTCMP value at least once since last clear. * | | |Note: This bit is only cleared by writing 1 to it. * |[5] |CAPOVF |Input Capture Counter Overflow Flag * | | |Flag is set by hardware when counter (ECAP_CNT) overflows from 0x00FF_FFFF to zero. * | | |0 = No overflow event has occurred since last clear. * | | |1 = Overflow event(s) has/have occurred since last clear. * | | |Note: This bit is only cleared by writing 1 to it. * |[6] |CAP0 |Value of Input Channel 0, CAP0 (Read Only) * | | |Reflecting the value of input channel 0, CAP0 * | | |(The bit is read only and write is ignored) * |[7] |CAP1 |Value of Input Channel 1, CAP1 (Read Only) * | | |Reflecting the value of input channel 1, CAP1 * | | |(The bit is read only and write is ignored) * |[8] |CAP2 |Value of Input Channel 2, CAP2 (Read Only) * | | |Reflecting the value of input channel 2, CAP2. * | | |(The bit is read only and write is ignored) */ __IO uint32_t CNT; /*!< [0x0000] Input Capture Counter */ __IO uint32_t HLD0; /*!< [0x0004] Input Capture Hold Register 0 */ __IO uint32_t HLD1; /*!< [0x0008] Input Capture Hold Register 1 */ __IO uint32_t HLD2; /*!< [0x000c] Input Capture Hold Register 2 */ __IO uint32_t CNTCMP; /*!< [0x0010] Input Capture Compare Register */ __IO uint32_t CTL0; /*!< [0x0014] Input Capture Control Register 0 */ __IO uint32_t CTL1; /*!< [0x0018] Input Capture Control Register 1 */ __IO uint32_t STATUS; /*!< [0x001c] Input Capture Status Register */ } ECAP_T; /** @addtogroup ECAP_CONST ECAP Bit Field Definition Constant Definitions for ECAP Controller @{ */ #define ECAP_CNT_CNT_Pos (0) /*!< ECAP_T::CNT: CNT Position */ #define ECAP_CNT_CNT_Msk (0xfffffful << ECAP_CNT_CNT_Pos) /*!< ECAP_T::CNT: CNT Mask */ #define ECAP_HLD0_HOLD_Pos (0) /*!< ECAP_T::HLD0: HOLD Position */ #define ECAP_HLD0_HOLD_Msk (0xfffffful << ECAP_HLD0_HOLD_Pos) /*!< ECAP_T::HLD0: HOLD Mask */ #define ECAP_HLD1_HOLD_Pos (0) /*!< ECAP_T::HLD1: HOLD Position */ #define ECAP_HLD1_HOLD_Msk (0xfffffful << ECAP_HLD1_HOLD_Pos) /*!< ECAP_T::HLD1: HOLD Mask */ #define ECAP_HLD2_HOLD_Pos (0) /*!< ECAP_T::HLD2: HOLD Position */ #define ECAP_HLD2_HOLD_Msk (0xfffffful << ECAP_HLD2_HOLD_Pos) /*!< ECAP_T::HLD2: HOLD Mask */ #define ECAP_CNTCMP_CNTCMP_Pos (0) /*!< ECAP_T::CNTCMP: CNTCMP Position */ #define ECAP_CNTCMP_CNTCMP_Msk (0xfffffful << ECAP_CNTCMP_CNTCMP_Pos) /*!< ECAP_T::CNTCMP: CNTCMP Mask */ #define ECAP_CTL0_NFCLKSEL_Pos (0) /*!< ECAP_T::CTL0: NFCLKSEL Position */ #define ECAP_CTL0_NFCLKSEL_Msk (0x7ul << ECAP_CTL0_NFCLKSEL_Pos) /*!< ECAP_T::CTL0: NFCLKSEL Mask */ #define ECAP_CTL0_CAPNFDIS_Pos (3) /*!< ECAP_T::CTL0: CAPNFDIS Position */ #define ECAP_CTL0_CAPNFDIS_Msk (0x1ul << ECAP_CTL0_CAPNFDIS_Pos) /*!< ECAP_T::CTL0: CAPNFDIS Mask */ #define ECAP_CTL0_IC0EN_Pos (4) /*!< ECAP_T::CTL0: IC0EN Position */ #define ECAP_CTL0_IC0EN_Msk (0x1ul << ECAP_CTL0_IC0EN_Pos) /*!< ECAP_T::CTL0: IC0EN Mask */ #define ECAP_CTL0_IC1EN_Pos (5) /*!< ECAP_T::CTL0: IC1EN Position */ #define ECAP_CTL0_IC1EN_Msk (0x1ul << ECAP_CTL0_IC1EN_Pos) /*!< ECAP_T::CTL0: IC1EN Mask */ #define ECAP_CTL0_IC2EN_Pos (6) /*!< ECAP_T::CTL0: IC2EN Position */ #define ECAP_CTL0_IC2EN_Msk (0x1ul << ECAP_CTL0_IC2EN_Pos) /*!< ECAP_T::CTL0: IC2EN Mask */ #define ECAP_CTL0_CAPSEL0_Pos (8) /*!< ECAP_T::CTL0: CAPSEL0 Position */ #define ECAP_CTL0_CAPSEL0_Msk (0x3ul << ECAP_CTL0_CAPSEL0_Pos) /*!< ECAP_T::CTL0: CAPSEL0 Mask */ #define ECAP_CTL0_CAPSEL1_Pos (10) /*!< ECAP_T::CTL0: CAPSEL1 Position */ #define ECAP_CTL0_CAPSEL1_Msk (0x3ul << ECAP_CTL0_CAPSEL1_Pos) /*!< ECAP_T::CTL0: CAPSEL1 Mask */ #define ECAP_CTL0_CAPSEL2_Pos (12) /*!< ECAP_T::CTL0: CAPSEL2 Position */ #define ECAP_CTL0_CAPSEL2_Msk (0x3ul << ECAP_CTL0_CAPSEL2_Pos) /*!< ECAP_T::CTL0: CAPSEL2 Mask */ #define ECAP_CTL0_CAPIEN0_Pos (16) /*!< ECAP_T::CTL0: CAPIEN0 Position */ #define ECAP_CTL0_CAPIEN0_Msk (0x1ul << ECAP_CTL0_CAPIEN0_Pos) /*!< ECAP_T::CTL0: CAPIEN0 Mask */ #define ECAP_CTL0_CAPIEN1_Pos (17) /*!< ECAP_T::CTL0: CAPIEN1 Position */ #define ECAP_CTL0_CAPIEN1_Msk (0x1ul << ECAP_CTL0_CAPIEN1_Pos) /*!< ECAP_T::CTL0: CAPIEN1 Mask */ #define ECAP_CTL0_CAPIEN2_Pos (18) /*!< ECAP_T::CTL0: CAPIEN2 Position */ #define ECAP_CTL0_CAPIEN2_Msk (0x1ul << ECAP_CTL0_CAPIEN2_Pos) /*!< ECAP_T::CTL0: CAPIEN2 Mask */ #define ECAP_CTL0_OVIEN_Pos (20) /*!< ECAP_T::CTL0: OVIEN Position */ #define ECAP_CTL0_OVIEN_Msk (0x1ul << ECAP_CTL0_OVIEN_Pos) /*!< ECAP_T::CTL0: OVIEN Mask */ #define ECAP_CTL0_CMPIEN_Pos (21) /*!< ECAP_T::CTL0: CMPIEN Position */ #define ECAP_CTL0_CMPIEN_Msk (0x1ul << ECAP_CTL0_CMPIEN_Pos) /*!< ECAP_T::CTL0: CMPIEN Mask */ #define ECAP_CTL0_CNTEN_Pos (24) /*!< ECAP_T::CTL0: CNTEN Position */ #define ECAP_CTL0_CNTEN_Msk (0x1ul << ECAP_CTL0_CNTEN_Pos) /*!< ECAP_T::CTL0: CNTEN Mask */ #define ECAP_CTL0_CMPCLREN_Pos (25) /*!< ECAP_T::CTL0: CMPCLREN Position */ #define ECAP_CTL0_CMPCLREN_Msk (0x1ul << ECAP_CTL0_CMPCLREN_Pos) /*!< ECAP_T::CTL0: CMPCLREN Mask */ #define ECAP_CTL0_CMPEN_Pos (28) /*!< ECAP_T::CTL0: CMPEN Position */ #define ECAP_CTL0_CMPEN_Msk (0x1ul << ECAP_CTL0_CMPEN_Pos) /*!< ECAP_T::CTL0: CMPEN Mask */ #define ECAP_CTL0_CAPEN_Pos (29) /*!< ECAP_T::CTL0: CAPEN Position */ #define ECAP_CTL0_CAPEN_Msk (0x1ul << ECAP_CTL0_CAPEN_Pos) /*!< ECAP_T::CTL0: CAPEN Mask */ #define ECAP_CTL1_EDGESEL0_Pos (0) /*!< ECAP_T::CTL1: EDGESEL0 Position */ #define ECAP_CTL1_EDGESEL0_Msk (0x3ul << ECAP_CTL1_EDGESEL0_Pos) /*!< ECAP_T::CTL1: EDGESEL0 Mask */ #define ECAP_CTL1_EDGESEL1_Pos (2) /*!< ECAP_T::CTL1: EDGESEL1 Position */ #define ECAP_CTL1_EDGESEL1_Msk (0x3ul << ECAP_CTL1_EDGESEL1_Pos) /*!< ECAP_T::CTL1: EDGESEL1 Mask */ #define ECAP_CTL1_EDGESEL2_Pos (4) /*!< ECAP_T::CTL1: EDGESEL2 Position */ #define ECAP_CTL1_EDGESEL2_Msk (0x3ul << ECAP_CTL1_EDGESEL2_Pos) /*!< ECAP_T::CTL1: EDGESEL2 Mask */ #define ECAP_CTL1_CAP0RLDEN_Pos (8) /*!< ECAP_T::CTL1: CAP0RLDEN Position */ #define ECAP_CTL1_CAP0RLDEN_Msk (0x1ul << ECAP_CTL1_CAP0RLDEN_Pos) /*!< ECAP_T::CTL1: CAP0RLDEN Mask */ #define ECAP_CTL1_CAP1RLDEN_Pos (9) /*!< ECAP_T::CTL1: CAP1RLDEN Position */ #define ECAP_CTL1_CAP1RLDEN_Msk (0x1ul << ECAP_CTL1_CAP1RLDEN_Pos) /*!< ECAP_T::CTL1: CAP1RLDEN Mask */ #define ECAP_CTL1_CAP2RLDEN_Pos (10) /*!< ECAP_T::CTL1: CAP2RLDEN Position */ #define ECAP_CTL1_CAP2RLDEN_Msk (0x1ul << ECAP_CTL1_CAP2RLDEN_Pos) /*!< ECAP_T::CTL1: CAP2RLDEN Mask */ #define ECAP_CTL1_OVRLDEN_Pos (11) /*!< ECAP_T::CTL1: OVRLDEN Position */ #define ECAP_CTL1_OVRLDEN_Msk (0x1ul << ECAP_CTL1_OVRLDEN_Pos) /*!< ECAP_T::CTL1: OVRLDEN Mask */ #define ECAP_CTL1_CLKSEL_Pos (12) /*!< ECAP_T::CTL1: CLKSEL Position */ #define ECAP_CTL1_CLKSEL_Msk (0x7ul << ECAP_CTL1_CLKSEL_Pos) /*!< ECAP_T::CTL1: CLKSEL Mask */ #define ECAP_CTL1_CNTSRCSEL_Pos (16) /*!< ECAP_T::CTL1: CNTSRCSEL Position */ #define ECAP_CTL1_CNTSRCSEL_Msk (0x3ul << ECAP_CTL1_CNTSRCSEL_Pos) /*!< ECAP_T::CTL1: CNTSRCSEL Mask */ #define ECAP_CTL1_CAP0CLREN_Pos (20) /*!< ECAP_T::CTL1: CAP0CLREN Position */ #define ECAP_CTL1_CAP0CLREN_Msk (0x1ul << ECAP_CTL1_CAP0CLREN_Pos) /*!< ECAP_T::CTL1: CAP0CLREN Mask */ #define ECAP_CTL1_CAP1CLREN_Pos (21) /*!< ECAP_T::CTL1: CAP1CLREN Position */ #define ECAP_CTL1_CAP1CLREN_Msk (0x1ul << ECAP_CTL1_CAP1CLREN_Pos) /*!< ECAP_T::CTL1: CAP1CLREN Mask */ #define ECAP_CTL1_CAP2CLREN_Pos (22) /*!< ECAP_T::CTL1: CAP2CLREN Position */ #define ECAP_CTL1_CAP2CLREN_Msk (0x1ul << ECAP_CTL1_CAP2CLREN_Pos) /*!< ECAP_T::CTL1: CAP2CLREN Mask */ #define ECAP_STATUS_CAPTF0_Pos (0) /*!< ECAP_T::STATUS: CAPTF0 Position */ #define ECAP_STATUS_CAPTF0_Msk (0x1ul << ECAP_STATUS_CAPTF0_Pos) /*!< ECAP_T::STATUS: CAPTF0 Mask */ #define ECAP_STATUS_CAPTF1_Pos (1) /*!< ECAP_T::STATUS: CAPTF1 Position */ #define ECAP_STATUS_CAPTF1_Msk (0x1ul << ECAP_STATUS_CAPTF1_Pos) /*!< ECAP_T::STATUS: CAPTF1 Mask */ #define ECAP_STATUS_CAPTF2_Pos (2) /*!< ECAP_T::STATUS: CAPTF2 Position */ #define ECAP_STATUS_CAPTF2_Msk (0x1ul << ECAP_STATUS_CAPTF2_Pos) /*!< ECAP_T::STATUS: CAPTF2 Mask */ #define ECAP_STATUS_CAPCMPF_Pos (4) /*!< ECAP_T::STATUS: CAPCMPF Position */ #define ECAP_STATUS_CAPCMPF_Msk (0x1ul << ECAP_STATUS_CAPCMPF_Pos) /*!< ECAP_T::STATUS: CAPCMPF Mask */ #define ECAP_STATUS_CAPOVF_Pos (5) /*!< ECAP_T::STATUS: CAPOVF Position */ #define ECAP_STATUS_CAPOVF_Msk (0x1ul << ECAP_STATUS_CAPOVF_Pos) /*!< ECAP_T::STATUS: CAPOVF Mask */ #define ECAP_STATUS_CAP0_Pos (8) /*!< ECAP_T::STATUS: CAP0 Position */ #define ECAP_STATUS_CAP0_Msk (0x1ul << ECAP_STATUS_CAP0_Pos) /*!< ECAP_T::STATUS: CAP0 Mask */ #define ECAP_STATUS_CAP1_Pos (9) /*!< ECAP_T::STATUS: CAP1 Position */ #define ECAP_STATUS_CAP1_Msk (0x1ul << ECAP_STATUS_CAP1_Pos) /*!< ECAP_T::STATUS: CAP1 Mask */ #define ECAP_STATUS_CAP2_Pos (10) /*!< ECAP_T::STATUS: CAP2 Position */ #define ECAP_STATUS_CAP2_Msk (0x1ul << ECAP_STATUS_CAP2_Pos) /*!< ECAP_T::STATUS: CAP2 Mask */ /**@}*/ /* ECAP_CONST */ /**@}*/ /* end of ECAP register group */ #endif /* __ECAP_REG_H__ */