Junichi Katsu
テスト用
Fork of
nRF51822
by 
Nordic Semiconductor
Diff: nordic/nrf-sdk/app_common/app_uart.h
- Revision:
- 37:c29c330d942c
- Parent:
- 0:eff01767de02
--- a/nordic/nrf-sdk/app_common/app_uart.h Thu Jul 03 10:01:02 2014 +0100
+++ b/nordic/nrf-sdk/app_common/app_uart.h Mon Jul 07 13:43:31 2014 +0100
@@ -24,41 +24,40 @@
#include <stdint.h>
#include <stdbool.h>
-#include "nordic_global.h"
-#include "app_util.h"
+#include "app_util_platform.h"
-#define UART_PIN_DISCONNECTED 0xFFFFFFFF /**< Value indicating that no pin is connected to this UART register. */
+#define UART_PIN_DISCONNECTED 0xFFFFFFFF /**< Value indicating that no pin is connected to this UART register. */
/**@brief UART Flow Control modes for the peripheral.
*/
typedef enum
{
- APP_UART_FLOW_CONTROL_DISABLED, /**< UART Hw Flow Control is disabled. */
- APP_UART_FLOW_CONTROL_ENABLED, /**< Standard UART Hw Flow Control is enabled. */
- APP_UART_FLOW_CONTROL_LOW_POWER /**< Specialized UART Hw Flow Control is used. The Low Power setting allows the nRF51 to Power Off the UART module when CTS is in-active, and re-enabling the UART when the CTS signal becomes active. This allows the nRF51 to safe power by only using the UART module when it is needed by the remote site. */
+ APP_UART_FLOW_CONTROL_DISABLED, /**< UART Hw Flow Control is disabled. */
+ APP_UART_FLOW_CONTROL_ENABLED, /**< Standard UART Hw Flow Control is enabled. */
+ APP_UART_FLOW_CONTROL_LOW_POWER /**< Specialized UART Hw Flow Control is used. The Low Power setting allows the nRF51 to Power Off the UART module when CTS is in-active, and re-enabling the UART when the CTS signal becomes active. This allows the nRF51 to safe power by only using the UART module when it is needed by the remote site. */
} app_uart_flow_control_t;
/**@brief UART communication structure holding configuration settings for the peripheral.
*/
typedef struct
{
- uint8_t rx_pin_no; /**< RX pin number. */
- uint8_t tx_pin_no; /**< TX pin number. */
- uint8_t rts_pin_no; /**< RTS pin number, only used if flow control is enabled. */
- uint8_t cts_pin_no; /**< CTS pin number, only used if flow control is enabled. */
- app_uart_flow_control_t flow_control; /**< Flow control setting, if flow control is used, the system will use low power UART mode, based on CTS signal. */
- bool use_parity; /**< Even parity if TRUE, no parity if FALSE. */
- uint32_t baud_rate; /**< Baud rate configuration. */
+ uint8_t rx_pin_no; /**< RX pin number. */
+ uint8_t tx_pin_no; /**< TX pin number. */
+ uint8_t rts_pin_no; /**< RTS pin number, only used if flow control is enabled. */
+ uint8_t cts_pin_no; /**< CTS pin number, only used if flow control is enabled. */
+ app_uart_flow_control_t flow_control; /**< Flow control setting, if flow control is used, the system will use low power UART mode, based on CTS signal. */
+ bool use_parity; /**< Even parity if TRUE, no parity if FALSE. */
+ uint32_t baud_rate; /**< Baud rate configuration. */
} app_uart_comm_params_t;
/**@brief UART buffer for transmitting/receiving data.
*/
typedef struct
{
- uint8_t * rx_buf; /**< Pointer to the RX buffer. */
- uint32_t rx_buf_size; /**< Size of the RX buffer. */
- uint8_t * tx_buf; /**< Pointer to the TX buffer. */
- uint32_t tx_buf_size; /**< Size of the TX buffer. */
+ uint8_t * rx_buf; /**< Pointer to the RX buffer. */
+ uint32_t rx_buf_size; /**< Size of the RX buffer. */
+ uint8_t * tx_buf; /**< Pointer to the TX buffer. */
+ uint32_t tx_buf_size; /**< Size of the TX buffer. */
} app_uart_buffers_t;
/**@brief Enumeration describing current state of the UART.
@@ -74,8 +73,8 @@
*/
typedef enum
{
- APP_UART_DISCONNECTED, /**< State indicating that the UART is disconnected and cannot receive or transmit bytes. */
- APP_UART_CONNECTED /**< State indicating that the UART is connected and ready to receive or transmit bytes. If flow control is disabled, the state will always be connected. */
+ APP_UART_DISCONNECTED, /**< State indicating that the UART is disconnected and cannot receive or transmit bytes. */
+ APP_UART_CONNECTED /**< State indicating that the UART is connected and ready to receive or transmit bytes. If flow control is disabled, the state will always be connected. */
} app_uart_connection_state_t;
/**@brief Enumeration which defines events used by the UART module upon data reception or error.
@@ -85,11 +84,11 @@
*/
typedef enum
{
- APP_UART_DATA_READY, /**< An event indicating that UART data has been received. The data is available in the FIFO and can be fetched using @ref app_uart_get. */
- APP_UART_FIFO_ERROR, /**< An error in the FIFO module used by the app_uart module has occured. The FIFO error code is stored in app_uart_evt_t.data.error_code field. */
- APP_UART_COMMUNICATION_ERROR, /**< An communication error has occured during reception. The error is stored in app_uart_evt_t.data.error_communication field. */
- APP_UART_TX_EMPTY, /**< An event indicating that UART has completed transmission of all available data in the TX FIFO. */
- APP_UART_DATA, /**< An event indicating that UART data has been received, and data is present in data field. This event is only used when no FIFO is configured. */
+ APP_UART_DATA_READY, /**< An event indicating that UART data has been received. The data is available in the FIFO and can be fetched using @ref app_uart_get. */
+ APP_UART_FIFO_ERROR, /**< An error in the FIFO module used by the app_uart module has occured. The FIFO error code is stored in app_uart_evt_t.data.error_code field. */
+ APP_UART_COMMUNICATION_ERROR, /**< An communication error has occured during reception. The error is stored in app_uart_evt_t.data.error_communication field. */
+ APP_UART_TX_EMPTY, /**< An event indicating that UART has completed transmission of all available data in the TX FIFO. */
+ APP_UART_DATA, /**< An event indicating that UART data has been received, and data is present in data field. This event is only used when no FIFO is configured. */
} app_uart_evt_type_t;
/**@brief Struct containing events from the UART module.
@@ -99,12 +98,12 @@
*/
typedef struct
{
- app_uart_evt_type_t evt_type; /**< Type of event. */
+ app_uart_evt_type_t evt_type; /**< Type of event. */
union
{
- uint32_t error_communication;/**< Field used if evt_type is: APP_UART_COMMUNICATION_ERROR. This field contains the value in the ERRORSRC register for the UART peripheral. The UART_ERRORSRC_x defines from @ref nrf51_bitfields.h can be used to parse the error code. See also the nRF51 Series Reference Manual for specification. */
- uint32_t error_code; /**< Field used if evt_type is: NRF_ERROR_x. Additional status/error code if the error event type is APP_UART_FIFO_ERROR. This error code refer to errors defined in nrf_error.h. */
- uint8_t value; /**< Field used if evt_type is: NRF_ERROR_x. Additional status/error code if the error event type is APP_UART_FIFO_ERROR. This error code refer to errors defined in nrf_error.h. */
+ uint32_t error_communication; /**< Field used if evt_type is: APP_UART_COMMUNICATION_ERROR. This field contains the value in the ERRORSRC register for the UART peripheral. The UART_ERRORSRC_x defines from @ref nrf51_bitfields.h can be used to parse the error code. See also the nRF51 Series Reference Manual for specification. */
+ uint32_t error_code; /**< Field used if evt_type is: NRF_ERROR_x. Additional status/error code if the error event type is APP_UART_FIFO_ERROR. This error code refer to errors defined in nrf_error.h. */
+ uint8_t value; /**< Field used if evt_type is: NRF_ERROR_x. Additional status/error code if the error event type is APP_UART_FIFO_ERROR. This error code refer to errors defined in nrf_error.h. */
} data;
} app_uart_evt_t;
@@ -115,7 +114,9 @@
*
* @param[in] p_app_uart_event Pointer to UART event.
*/
-typedef void (*app_uart_event_handler_t) (app_uart_evt_t * p_app_uart_event);
+
+
+typedef void (* app_uart_event_handler_t) (app_uart_evt_t * p_app_uart_event);
/**@brief Macro for safe initialization of the UART module in a single user instance when using
* a FIFO together with UART.
@@ -132,7 +133,7 @@
* @note Since this macro allocates a buffer and registers the module as a GPIOTE user when flow
* control is enabled, it must only be called once.
*/
-#define APP_UART_FIFO_INIT(P_COMM_PARAMS, RX_BUF_SIZE, TX_BUF_SIZE, EVT_HANDLER, IRQ_PRIO, ERR_CODE)\
+#define APP_UART_FIFO_INIT(P_COMM_PARAMS, RX_BUF_SIZE, TX_BUF_SIZE, EVT_HANDLER, IRQ_PRIO, ERR_CODE) \
do \
{ \
uint16_t APP_UART_UID = 0; \
@@ -141,9 +142,9 @@
static uint8_t tx_buf[TX_BUF_SIZE]; \
\
buffers.rx_buf = rx_buf; \
- buffers.rx_buf_size = sizeof(rx_buf); \
+ buffers.rx_buf_size = sizeof (rx_buf); \
buffers.tx_buf = tx_buf; \
- buffers.tx_buf_size = sizeof(tx_buf); \
+ buffers.tx_buf_size = sizeof (tx_buf); \
ERR_CODE = app_uart_init(P_COMM_PARAMS, &buffers, EVT_HANDLER, IRQ_PRIO, &APP_UART_UID); \
} while (0)
@@ -203,15 +204,15 @@
* @retval NRF_ERROR_NO_MEM GPIOTE module has reached the maximum number of users.
*/
uint32_t app_uart_init(const app_uart_comm_params_t * p_comm_params,
- app_uart_buffers_t * p_buffers,
- app_uart_event_handler_t error_handler,
- app_irq_priority_t irq_priority,
- uint16_t * p_uart_uid);
+ app_uart_buffers_t * p_buffers,
+ app_uart_event_handler_t error_handler,
+ app_irq_priority_t irq_priority,
+ uint16_t * p_uart_uid);
/**@brief Function for getting a byte from the UART.
*
* @details This function will get the next byte from the RX buffer. If the RX buffer is empty
- * an error code will be returned and the app_uart module will generate an event upon
+ * an error code will be returned and the app_uart module will generate an event upon
* reception of the first byte which is added to the RX buffer.
*
* @param[out] p_byte Pointer to an address where next byte received on the UART will be copied.
@@ -238,10 +239,10 @@
*
* @details If flow control is disabled, the state is assumed to always be APP_UART_CONNECTED.
*
- * When using flow control the state will be controlled by the CTS. If CTS is set active
+ * When using flow control the state will be controlled by the CTS. If CTS is set active
* by the remote side, or the app_uart module is in the process of transmitting a byte,
* app_uart is in APP_UART_CONNECTED state. If CTS is set inactive by remote side app_uart
- * will not get into APP_UART_DISCONNECTED state until the last byte in the TXD register
+ * will not get into APP_UART_DISCONNECTED state until the last byte in the TXD register
* is fully transmitted.
*
* Internal states in the state machine are mapped to the general connected/disconnected
@@ -280,6 +281,6 @@
uint32_t app_uart_close(uint16_t app_uart_id);
-#endif // APP_UART_H__
+#endif //APP_UART_H__
/** @} */