mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F030R8/stm32f0xx_crs.c
- Revision:
- 76:aeb1df146756
- Child:
- 106:ced8cbb51063
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F030R8/stm32f0xx_crs.c Mon Jan 27 14:30:07 2014 +0000 @@ -0,0 +1,466 @@ +/** + ****************************************************************************** + * @file stm32f0xx_crs.c + * @author MCD Application Team + * @version V1.3.0 + * @date 16-January-2014 + * @brief This file provides firmware functions to manage the following + * functionalities of CRS peripheral applicable only on STM32F042 and + * STM32F072 devices: + * + Configuration of the CRS peripheral + * + Interrupts and flags management + * + * + * @verbatim + =============================================================================== + ##### How to use this driver ##### + =============================================================================== + [..] + + (+) Enable CRS AHB clock using RCC_APB1eriphClockCmd(RCC_APB1Periph_CRS, ENABLE) + function + + + @endverbatim + * + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT 2014 STMicroelectronics</center></h2> + * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f0xx_crs.h" +#include "stm32f0xx_rcc.h" + +/** @addtogroup STM32F0xx_StdPeriph_Driver + * @{ + */ + +/** @defgroup CRS + * @brief CRS driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* CRS Flag Mask */ +#define FLAG_MASK ((uint32_t)0x700) + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup CRS_Private_Functions + * @{ + */ + +/** @defgroup CRS_Group1 Configuration of the CRS functions + * @brief Configuration of the CRS functions + * +@verbatim + =============================================================================== + ##### CRS configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes CRS peripheral registers to their default reset values. + * @param None + * @retval None + */ +void CRS_DeInit(void) +{ + RCC_APB1PeriphResetCmd(RCC_APB1Periph_CRS, ENABLE); + RCC_APB1PeriphResetCmd(RCC_APB1Periph_CRS, DISABLE); +} + +/** + * @brief Adjusts the Internal High Speed 48 oscillator (HSI 48) calibration value. + * @note The calibration is used to compensate for the variations in voltage + * and temperature that influence the frequency of the internal HSI48 RC. + * @note This function can be called only when the AUTOTRIMEN bit is reset. + * @param CRS_HSI48CalibrationValue: + * @retval None + */ +void CRS_AdjustHSI48CalibrationValue(uint8_t CRS_HSI48CalibrationValue) +{ + /* Clear TRIM[5:0] bits */ + CRS->CR &= ~CRS_CR_TRIM; + + /* Set the TRIM[5:0] bits according to CRS_HSI48CalibrationValue value */ + CRS->CR |= (uint32_t)((uint32_t)CRS_HSI48CalibrationValue << 8); + +} + +/** + * @brief Enables or disables the oscillator clock for frequency error counter. + * @note when the CEN bit is set the CRS_CFGR register becomes write-protected. + * @param NewState: new state of the frequency error counter. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void CRS_FrequencyErrorCounterCmd(FunctionalState NewState) +{ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + CRS->CR |= CRS_CR_CEN; + } + else + { + CRS->CR &= ~CRS_CR_CEN; + } +} + +/** + * @brief Enables or disables the automatic hardware adjustement of TRIM bits. + * @note When the AUTOTRIMEN bit is set the CRS_CFGR register becomes write-protected. + * @param NewState: new state of the automatic trimming. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void CRS_AutomaticCalibrationCmd(FunctionalState NewState) +{ + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + CRS->CR |= CRS_CR_AUTOTRIMEN; + } +else + { + CRS->CR &= ~CRS_CR_AUTOTRIMEN; + } +} + +/** + * @brief Generate the software synchronization event + * @param None + * @retval None + */ +void CRS_SoftwareSynchronizationGenerate(void) +{ + CRS->CR |= CRS_CR_SWSYNC; +} + +/** + * @brief Adjusts the Internal High Speed 48 oscillator (HSI 48) calibration value. + * @note The calibration is used to compensate for the variations in voltage + * and temperature that influence the frequency of the internal HSI48 RC. + * @note This function can be called only when the CEN bit is reset. + * @param CRS_ReloadValue: specifies the HSI calibration trimming value. + * This parameter must be a number between 0 and . + * @retval None + */ +void CRS_FrequencyErrorCounterReload(uint32_t CRS_ReloadValue) +{ + + /* Clear RELOAD[15:0] bits */ + CRS->CFGR &= ~CRS_CFGR_RELOAD; + + /* Set the RELOAD[15:0] bits according to CRS_ReloadValue value */ + CRS->CFGR |= (uint32_t)CRS_ReloadValue; + +} + +/** + * @brief + * @note This function can be called only when the CEN bit is reset. + * @param CRS_ErrorLimitValue: specifies the HSI calibration trimming value. + * This parameter must be a number between 0 and . + * @retval None + */ +void CRS_FrequencyErrorLimitConfig(uint8_t CRS_ErrorLimitValue) +{ + /* Clear FELIM[7:0] bits */ + CRS->CFGR &= ~CRS_CFGR_FELIM; + + /* Set the FELIM[7:0] bits according to CRS_ErrorLimitValue value */ + CRS->CFGR |= (uint32_t)CRS_ErrorLimitValue; +} + +/** + * @brief + * @note This function can be called only when the CEN bit is reset. + * @param CRS_Prescaler: specifies the HSI calibration trimming value. + * This parameter can be one of the following values: + * @arg CRS_SYNC_Div1: + * @arg CRS_SYNC_Div2: + * @arg CRS_SYNC_Div4: + * @arg CRS_SYNC_Div8: + * @arg CRS_SYNC_Div16: + * @arg CRS_SYNC_Div32: + * @arg CRS_SYNC_Div64: + * @arg CRS_SYNC_Div128: + * @retval None + */ +void CRS_SynchronizationPrescalerConfig(uint32_t CRS_Prescaler) +{ + /* Check the parameters */ + assert_param(IS_CRS_SYNC_DIV(CRS_Prescaler)); + + /* Clear SYNCDIV[2:0] bits */ + CRS->CFGR &= ~CRS_CFGR_SYNCDIV; + + /* Set the CRS_CFGR_SYNCDIV[2:0] bits according to CRS_Prescaler value */ + CRS->CFGR |= CRS_Prescaler; +} + +/** + * @brief + * @note This function can be called only when the CEN bit is reset. + * @param CRS_Source: . + * This parameter can be one of the following values: + * @arg CRS_SYNCSource_GPIO: + * @arg CRS_SYNCSource_LSE: + * @arg CRS_SYNCSource_USB: + * @retval None + */ +void CRS_SynchronizationSourceConfig(uint32_t CRS_Source) +{ + /* Check the parameters */ + assert_param(IS_CRS_SYNC_SOURCE(CRS_Source)); + + /* Clear SYNCSRC[1:0] bits */ + CRS->CFGR &= ~CRS_CFGR_SYNCSRC; + + /* Set the SYNCSRC[1:0] bits according to CRS_Source value */ + CRS->CFGR |= CRS_Source; +} + +/** + * @brief + * @note This function can be called only when the CEN bit is reset. + * @param CRS_Polarity: . + * This parameter can be one of the following values: + * @arg CRS_SYNCPolarity_Rising: + * @arg CRS_SYNCPolarity_Falling: + * @retval None + */ +void CRS_SynchronizationPolarityConfig(uint32_t CRS_Polarity) +{ + /* Check the parameters */ + assert_param(IS_CRS_SYNC_POLARITY(CRS_Polarity)); + + /* Clear SYNCSPOL bit */ + CRS->CFGR &= ~CRS_CFGR_SYNCPOL; + + /* Set the SYNCSPOL bits according to CRS_Polarity value */ + CRS->CFGR |= CRS_Polarity; +} + +/** + * @brief Returns the Relaod value. + * @param None + * @retval The reload value + */ +uint32_t CRS_GetReloadValue(void) +{ + return ((uint32_t)(CRS->CFGR & CRS_CFGR_RELOAD)); +} + +/** + * @brief Returns the HSI48 Calibration value. + * @param None + * @retval The reload value + */ +uint32_t CRS_GetHSI48CalibrationValue(void) +{ + return (((uint32_t)(CRS->CR & CRS_CR_TRIM)) >> 8); +} + +/** + * @brief Returns the frequency error capture. + * @param None + * @retval The frequency error capture value + */ +uint32_t CRS_GetFrequencyErrorValue(void) +{ + return ((uint32_t)(CRS->ISR & CRS_ISR_FECAP)); +} + +/** + * @brief Returns the frequency error direction. + * @param None + * @retval The frequency error direction. The returned value can be one + * of the following values: + * - 0x00: Up counting + * - 0x8000: Down counting + */ +uint32_t CRS_GetFrequencyErrorDirection(void) +{ + return ((uint32_t)(CRS->ISR & CRS_ISR_FEDIR)); +} + +/** @defgroup CRS_Group2 Interrupts and flags management functions + * @brief Interrupts and flags management functions + * +@verbatim + =============================================================================== + ##### Interrupts and flags management functions ##### + =============================================================================== +@endverbatim + * @{ + */ +/** + * @brief Enables or disables the specified CRS interrupts. + * @param CRS_IT: specifies the RCC interrupt sources to be enabled or disabled. + * This parameter can be any combination of the following values: + * @arg CRS_IT_SYNCOK: + * @arg CRS_IT_SYNCWARN: + * @arg CRS_IT_ERR: + * @arg CRS_IT_ESYNC: + * @param NewState: new state of the specified CRS interrupts. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +void CRS_ITConfig(uint32_t CRS_IT, FunctionalState NewState) +{ + /* Check the parameters */ + assert_param(IS_CRS_IT(CRS_IT)); + assert_param(IS_FUNCTIONAL_STATE(NewState)); + + if (NewState != DISABLE) + { + CRS->CR |= CRS_IT; + } + else + { + CRS->CR &= ~CRS_IT; + } +} + +/** + * @brief Checks whether the specified CRS flag is set or not. + * @param CRS_FLAG: specifies the flag to check. + * This parameter can be one of the following values: + * @arg CRS_FLAG_SYNCOK: + * @arg CRS_FLAG_SYNCWARN: + * @arg CRS_FLAG_ERR: + * @arg CRS_FLAG_ESYNC: + * @arg CRS_FLAG_TRIMOVF: + * @arg CRS_FLAG_SYNCERR: + * @arg CRS_FLAG_SYNCMISS: + * @retval The new state of CRS_FLAG (SET or RESET). + */ +FlagStatus CRS_GetFlagStatus(uint32_t CRS_FLAG) +{ + /* Check the parameters */ + assert_param(IS_CRS_FLAG(CRS_FLAG)); + + return ((FlagStatus)(CRS->ISR & CRS_FLAG)); +} + +/** + * @brief Clears the CRS specified FLAG. + * @param CRS_FLAG: specifies the flag to check. + * This parameter can be one of the following values: + * @arg CRS_FLAG_SYNCOK: + * @arg CRS_FLAG_SYNCWARN: + * @arg CRS_FLAG_ERR: + * @arg CRS_FLAG_ESYNC: + * @arg CRS_FLAG_TRIMOVF: + * @arg CRS_FLAG_SYNCERR: + * @arg CRS_FLAG_SYNCMISS: + * @retval None + */ +void CRS_ClearFlag(uint32_t CRS_FLAG) +{ + /* Check the parameters */ + assert_param(IS_CRS_FLAG(CRS_FLAG)); + + if ((CRS_FLAG & FLAG_MASK)!= 0) + { + CRS->ICR |= CRS_ICR_ERRC; + } + else + { + CRS->ICR |= CRS_FLAG; + } +} + +/** + * @brief Checks whether the specified CRS IT pending bit is set or not. + * @param CRS_IT: specifies the IT pending bit to check. + * This parameter can be one of the following values: + * @arg CRS_IT_SYNCOK: + * @arg CRS_IT_SYNCWARN: + * @arg CRS_IT_ERR: + * @arg CRS_IT_ESYNC: + * @arg CRS_IT_TRIMOVF: + * @arg CRS_IT_SYNCERR: + * @arg CRS_IT_SYNCMISS: + * @retval The new state of CRS_IT (SET or RESET). + */ +ITStatus CRS_GetITStatus(uint32_t CRS_IT) +{ + /* Check the parameters */ + assert_param(IS_CRS_GET_IT(CRS_IT)); + + return ((ITStatus)(CRS->ISR & CRS_IT)); +} + +/** + * @brief Clears the CRS specified IT pending bi. + * @param CRS_FLAG: specifies the IT pending bi to clear. + * This parameter can be one of the following values: + * @arg CRS_IT_SYNCOK: + * @arg CRS_IT_SYNCWARN: + * @arg CRS_IT_ERR: + * @arg CRS_IT_ESYNC: + * @arg CRS_IT_TRIMOVF: + * @arg CRS_IT_SYNCERR: + * @arg CRS_IT_SYNCMISS: + * @retval None + */ +void CRS_ClearITPendingBit(uint32_t CRS_IT) +{ + /* Check the parameters */ + assert_param(IS_CRS_CLEAR_IT(CRS_IT)); + + if ((CRS_IT & FLAG_MASK)!= 0) + { + CRS->ICR |= CRS_ICR_ERRC; + } + else + { + CRS->ICR |= CRS_IT; + } +} +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/