001
Diff: targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_ll_sdmmc.h
- Revision:
- 0:13413ea9a877
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_ll_sdmmc.h Sun Jun 12 14:02:44 2022 +0000 @@ -0,0 +1,1136 @@ +/** + ****************************************************************************** + * @file stm32f4xx_ll_sdmmc.h + * @author MCD Application Team + * @version V1.7.1 + * @date 14-April-2017 + * @brief Header file of SDMMC HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_LL_SDMMC_H +#define __STM32F4xx_LL_SDMMC_H + +#ifdef __cplusplus + extern "C" { +#endif + +#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \ + defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \ + defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \ + defined(STM32F469xx) || defined(STM32F479xx) || defined(STM32F412Zx) || defined(STM32F412Vx) || \ + defined(STM32F412Rx) || defined(STM32F412Cx) || defined(STM32F413xx) || defined(STM32F423xx) + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal_def.h" + +/** @addtogroup STM32F4xx_Driver + * @{ + */ + +/** @addtogroup SDMMC_LL + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup SDMMC_LL_Exported_Types SDMMC_LL Exported Types + * @{ + */ + +/** + * @brief SDMMC Configuration Structure definition + */ +typedef struct +{ + uint32_t ClockEdge; /*!< Specifies the clock transition on which the bit capture is made. + This parameter can be a value of @ref SDMMC_LL_Clock_Edge */ + + uint32_t ClockBypass; /*!< Specifies whether the SDMMC Clock divider bypass is + enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_Clock_Bypass */ + + uint32_t ClockPowerSave; /*!< Specifies whether SDMMC Clock output is enabled or + disabled when the bus is idle. + This parameter can be a value of @ref SDMMC_LL_Clock_Power_Save */ + + uint32_t BusWide; /*!< Specifies the SDMMC bus width. + This parameter can be a value of @ref SDMMC_LL_Bus_Wide */ + + uint32_t HardwareFlowControl; /*!< Specifies whether the SDMMC hardware flow control is enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_Hardware_Flow_Control */ + + uint32_t ClockDiv; /*!< Specifies the clock frequency of the SDMMC controller. + This parameter can be a value between Min_Data = 0 and Max_Data = 255 */ + +}SDIO_InitTypeDef; + + +/** + * @brief SDMMC Command Control structure + */ +typedef struct +{ + uint32_t Argument; /*!< Specifies the SDMMC command argument which is sent + to a card as part of a command message. If a command + contains an argument, it must be loaded into this register + before writing the command to the command register. */ + + uint32_t CmdIndex; /*!< Specifies the SDMMC command index. It must be Min_Data = 0 and + Max_Data = 64 */ + + uint32_t Response; /*!< Specifies the SDMMC response type. + This parameter can be a value of @ref SDMMC_LL_Response_Type */ + + uint32_t WaitForInterrupt; /*!< Specifies whether SDMMC wait for interrupt request is + enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_Wait_Interrupt_State */ + + uint32_t CPSM; /*!< Specifies whether SDMMC Command path state machine (CPSM) + is enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_CPSM_State */ +}SDIO_CmdInitTypeDef; + + +/** + * @brief SDMMC Data Control structure + */ +typedef struct +{ + uint32_t DataTimeOut; /*!< Specifies the data timeout period in card bus clock periods. */ + + uint32_t DataLength; /*!< Specifies the number of data bytes to be transferred. */ + + uint32_t DataBlockSize; /*!< Specifies the data block size for block transfer. + This parameter can be a value of @ref SDMMC_LL_Data_Block_Size */ + + uint32_t TransferDir; /*!< Specifies the data transfer direction, whether the transfer + is a read or write. + This parameter can be a value of @ref SDMMC_LL_Transfer_Direction */ + + uint32_t TransferMode; /*!< Specifies whether data transfer is in stream or block mode. + This parameter can be a value of @ref SDMMC_LL_Transfer_Type */ + + uint32_t DPSM; /*!< Specifies whether SDMMC Data path state machine (DPSM) + is enabled or disabled. + This parameter can be a value of @ref SDMMC_LL_DPSM_State */ +}SDIO_DataInitTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup SDMMC_LL_Exported_Constants SDMMC_LL Exported Constants + * @{ + */ +#define SDMMC_ERROR_NONE 0x00000000U /*!< No error */ +#define SDMMC_ERROR_CMD_CRC_FAIL 0x00000001U /*!< Command response received (but CRC check failed) */ +#define SDMMC_ERROR_DATA_CRC_FAIL 0x00000002U /*!< Data block sent/received (CRC check failed) */ +#define SDMMC_ERROR_CMD_RSP_TIMEOUT 0x00000004U /*!< Command response timeout */ +#define SDMMC_ERROR_DATA_TIMEOUT 0x00000008U /*!< Data timeout */ +#define SDMMC_ERROR_TX_UNDERRUN 0x00000010U /*!< Transmit FIFO underrun */ +#define SDMMC_ERROR_RX_OVERRUN 0x00000020U /*!< Receive FIFO overrun */ +#define SDMMC_ERROR_ADDR_MISALIGNED 0x00000040U /*!< Misaligned address */ +#define SDMMC_ERROR_BLOCK_LEN_ERR 0x00000080U /*!< Transferred block length is not allowed for the card or the + number of transferred bytes does not match the block length */ +#define SDMMC_ERROR_ERASE_SEQ_ERR 0x00000100U /*!< An error in the sequence of erase command occurs */ +#define SDMMC_ERROR_BAD_ERASE_PARAM 0x00000200U /*!< An invalid selection for erase groups */ +#define SDMMC_ERROR_WRITE_PROT_VIOLATION 0x00000400U /*!< Attempt to program a write protect block */ +#define SDMMC_ERROR_LOCK_UNLOCK_FAILED 0x00000800U /*!< Sequence or password error has been detected in unlock + command or if there was an attempt to access a locked card */ +#define SDMMC_ERROR_COM_CRC_FAILED 0x00001000U /*!< CRC check of the previous command failed */ +#define SDMMC_ERROR_ILLEGAL_CMD 0x00002000U /*!< Command is not legal for the card state */ +#define SDMMC_ERROR_CARD_ECC_FAILED 0x00004000U /*!< Card internal ECC was applied but failed to correct the data */ +#define SDMMC_ERROR_CC_ERR 0x00008000U /*!< Internal card controller error */ +#define SDMMC_ERROR_GENERAL_UNKNOWN_ERR 0x00010000U /*!< General or unknown error */ +#define SDMMC_ERROR_STREAM_READ_UNDERRUN 0x00020000U /*!< The card could not sustain data reading in stream rmode */ +#define SDMMC_ERROR_STREAM_WRITE_OVERRUN 0x00040000U /*!< The card could not sustain data programming in stream mode */ +#define SDMMC_ERROR_CID_CSD_OVERWRITE 0x00080000U /*!< CID/CSD overwrite error */ +#define SDMMC_ERROR_WP_ERASE_SKIP 0x00100000U /*!< Only partial address space was erased */ +#define SDMMC_ERROR_CARD_ECC_DISABLED 0x00200000U /*!< Command has been executed without using internal ECC */ +#define SDMMC_ERROR_ERASE_RESET 0x00400000U /*!< Erase sequence was cleared before executing because an out + of erase sequence command was received */ +#define SDMMC_ERROR_AKE_SEQ_ERR 0x00800000U /*!< Error in sequence of authentication */ +#define SDMMC_ERROR_INVALID_VOLTRANGE 0x01000000U /*!< Error in case of invalid voltage range */ +#define SDMMC_ERROR_ADDR_OUT_OF_RANGE 0x02000000U /*!< Error when addressed block is out of range */ +#define SDMMC_ERROR_REQUEST_NOT_APPLICABLE 0x04000000U /*!< Error when command request is not applicable */ +#define SDMMC_ERROR_INVALID_PARAMETER 0x08000000U /*!< the used parameter is not valid */ +#define SDMMC_ERROR_UNSUPPORTED_FEATURE 0x10000000U /*!< Error when feature is not insupported */ +#define SDMMC_ERROR_BUSY 0x20000000U /*!< Error when transfer process is busy */ +#define SDMMC_ERROR_DMA 0x40000000U /*!< Error while DMA transfer */ +#define SDMMC_ERROR_TIMEOUT 0x80000000U /*!< Timeout error */ + +/** + * @brief SDMMC Commands Index + */ +#define SDMMC_CMD_GO_IDLE_STATE ((uint8_t)0) /*!< Resets the SD memory card. */ +#define SDMMC_CMD_SEND_OP_COND ((uint8_t)1) /*!< Sends host capacity support information and activates the card's initialization process. */ +#define SDMMC_CMD_ALL_SEND_CID ((uint8_t)2) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */ +#define SDMMC_CMD_SET_REL_ADDR ((uint8_t)3) /*!< Asks the card to publish a new relative address (RCA). */ +#define SDMMC_CMD_SET_DSR ((uint8_t)4) /*!< Programs the DSR of all cards. */ +#define SDMMC_CMD_SDMMC_SEN_OP_COND ((uint8_t)5) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its + operating condition register (OCR) content in the response on the CMD line. */ +#define SDMMC_CMD_HS_SWITCH ((uint8_t)6) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */ +#define SDMMC_CMD_SEL_DESEL_CARD ((uint8_t)7) /*!< Selects the card by its own relative address and gets deselected by any other address */ +#define SDMMC_CMD_HS_SEND_EXT_CSD ((uint8_t)8) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information + and asks the card whether card supports voltage. */ +#define SDMMC_CMD_SEND_CSD ((uint8_t)9) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */ +#define SDMMC_CMD_SEND_CID ((uint8_t)10) /*!< Addressed card sends its card identification (CID) on the CMD line. */ +#define SDMMC_CMD_READ_DAT_UNTIL_STOP ((uint8_t)11) /*!< SD card doesn't support it. */ +#define SDMMC_CMD_STOP_TRANSMISSION ((uint8_t)12) /*!< Forces the card to stop transmission. */ +#define SDMMC_CMD_SEND_STATUS ((uint8_t)13) /*!< Addressed card sends its status register. */ +#define SDMMC_CMD_HS_BUSTEST_READ ((uint8_t)14) /*!< Reserved */ +#define SDMMC_CMD_GO_INACTIVE_STATE ((uint8_t)15) /*!< Sends an addressed card into the inactive state. */ +#define SDMMC_CMD_SET_BLOCKLEN ((uint8_t)16) /*!< Sets the block length (in bytes for SDSC) for all following block commands + (read, write, lock). Default block length is fixed to 512 Bytes. Not effective + for SDHS and SDXC. */ +#define SDMMC_CMD_READ_SINGLE_BLOCK ((uint8_t)17) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of + fixed 512 bytes in case of SDHC and SDXC. */ +#define SDMMC_CMD_READ_MULT_BLOCK ((uint8_t)18) /*!< Continuously transfers data blocks from card to host until interrupted by + STOP_TRANSMISSION command. */ +#define SDMMC_CMD_HS_BUSTEST_WRITE ((uint8_t)19) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */ +#define SDMMC_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20) /*!< Speed class control command. */ +#define SDMMC_CMD_SET_BLOCK_COUNT ((uint8_t)23) /*!< Specify block count for CMD18 and CMD25. */ +#define SDMMC_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of + fixed 512 bytes in case of SDHC and SDXC. */ +#define SDMMC_CMD_WRITE_MULT_BLOCK ((uint8_t)25) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */ +#define SDMMC_CMD_PROG_CID ((uint8_t)26) /*!< Reserved for manufacturers. */ +#define SDMMC_CMD_PROG_CSD ((uint8_t)27) /*!< Programming of the programmable bits of the CSD. */ +#define SDMMC_CMD_SET_WRITE_PROT ((uint8_t)28) /*!< Sets the write protection bit of the addressed group. */ +#define SDMMC_CMD_CLR_WRITE_PROT ((uint8_t)29) /*!< Clears the write protection bit of the addressed group. */ +#define SDMMC_CMD_SEND_WRITE_PROT ((uint8_t)30) /*!< Asks the card to send the status of the write protection bits. */ +#define SDMMC_CMD_SD_ERASE_GRP_START ((uint8_t)32) /*!< Sets the address of the first write block to be erased. (For SD card only). */ +#define SDMMC_CMD_SD_ERASE_GRP_END ((uint8_t)33) /*!< Sets the address of the last write block of the continuous range to be erased. */ +#define SDMMC_CMD_ERASE_GRP_START ((uint8_t)35) /*!< Sets the address of the first write block to be erased. Reserved for each command + system set by switch function command (CMD6). */ +#define SDMMC_CMD_ERASE_GRP_END ((uint8_t)36) /*!< Sets the address of the last write block of the continuous range to be erased. + Reserved for each command system set by switch function command (CMD6). */ +#define SDMMC_CMD_ERASE ((uint8_t)38) /*!< Reserved for SD security applications. */ +#define SDMMC_CMD_FAST_IO ((uint8_t)39) /*!< SD card doesn't support it (Reserved). */ +#define SDMMC_CMD_GO_IRQ_STATE ((uint8_t)40) /*!< SD card doesn't support it (Reserved). */ +#define SDMMC_CMD_LOCK_UNLOCK ((uint8_t)42) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by + the SET_BLOCK_LEN command. */ +#define SDMMC_CMD_APP_CMD ((uint8_t)55) /*!< Indicates to the card that the next command is an application specific command rather + than a standard command. */ +#define SDMMC_CMD_GEN_CMD ((uint8_t)56) /*!< Used either to transfer a data block to the card or to get a data block from the card + for general purpose/application specific commands. */ +#define SDMMC_CMD_NO_CMD ((uint8_t)64) /*!< No command */ + +/** + * @brief Following commands are SD Card Specific commands. + * SDMMC_APP_CMD should be sent before sending these commands. + */ +#define SDMMC_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus + widths are given in SCR register. */ +#define SDMMC_CMD_SD_APP_STATUS ((uint8_t)13) /*!< (ACMD13) Sends the SD status. */ +#define SDMMC_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with + 32bit+CRC data block. */ +#define SDMMC_CMD_SD_APP_OP_COND ((uint8_t)41) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to + send its operating condition register (OCR) content in the response on the CMD line. */ +#define SDMMC_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42) /*!< (ACMD42) Connect/Disconnect the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card */ +#define SDMMC_CMD_SD_APP_SEND_SCR ((uint8_t)51) /*!< Reads the SD Configuration Register (SCR). */ +#define SDMMC_CMD_SDMMC_RW_DIRECT ((uint8_t)52) /*!< For SD I/O card only, reserved for security specification. */ +#define SDMMC_CMD_SDMMC_RW_EXTENDED ((uint8_t)53) /*!< For SD I/O card only, reserved for security specification. */ + +/** + * @brief Following commands are SD Card Specific security commands. + * SDMMC_CMD_APP_CMD should be sent before sending these commands. + */ +#define SDMMC_CMD_SD_APP_GET_MKB ((uint8_t)43) +#define SDMMC_CMD_SD_APP_GET_MID ((uint8_t)44) +#define SDMMC_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45) +#define SDMMC_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46) +#define SDMMC_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47) +#define SDMMC_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48) +#define SDMMC_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18) +#define SDMMC_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25) +#define SDMMC_CMD_SD_APP_SECURE_ERASE ((uint8_t)38) +#define SDMMC_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49) +#define SDMMC_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48) + +/** + * @brief Masks for errors Card Status R1 (OCR Register) + */ +#define SDMMC_OCR_ADDR_OUT_OF_RANGE 0x80000000U +#define SDMMC_OCR_ADDR_MISALIGNED 0x40000000U +#define SDMMC_OCR_BLOCK_LEN_ERR 0x20000000U +#define SDMMC_OCR_ERASE_SEQ_ERR 0x10000000U +#define SDMMC_OCR_BAD_ERASE_PARAM 0x08000000U +#define SDMMC_OCR_WRITE_PROT_VIOLATION 0x04000000U +#define SDMMC_OCR_LOCK_UNLOCK_FAILED 0x01000000U +#define SDMMC_OCR_COM_CRC_FAILED 0x00800000U +#define SDMMC_OCR_ILLEGAL_CMD 0x00400000U +#define SDMMC_OCR_CARD_ECC_FAILED 0x00200000U +#define SDMMC_OCR_CC_ERROR 0x00100000U +#define SDMMC_OCR_GENERAL_UNKNOWN_ERROR 0x00080000U +#define SDMMC_OCR_STREAM_READ_UNDERRUN 0x00040000U +#define SDMMC_OCR_STREAM_WRITE_OVERRUN 0x00020000U +#define SDMMC_OCR_CID_CSD_OVERWRITE 0x00010000U +#define SDMMC_OCR_WP_ERASE_SKIP 0x00008000U +#define SDMMC_OCR_CARD_ECC_DISABLED 0x00004000U +#define SDMMC_OCR_ERASE_RESET 0x00002000U +#define SDMMC_OCR_AKE_SEQ_ERROR 0x00000008U +#define SDMMC_OCR_ERRORBITS 0xFDFFE008U + +/** + * @brief Masks for R6 Response + */ +#define SDMMC_R6_GENERAL_UNKNOWN_ERROR 0x00002000U +#define SDMMC_R6_ILLEGAL_CMD 0x00004000U +#define SDMMC_R6_COM_CRC_FAILED 0x00008000U + +#define SDMMC_VOLTAGE_WINDOW_SD 0x80100000U +#define SDMMC_HIGH_CAPACITY 0x40000000U +#define SDMMC_STD_CAPACITY 0x00000000U +#define SDMMC_CHECK_PATTERN 0x000001AAU + +#define SDMMC_MAX_VOLT_TRIAL 0x0000FFFFU + +#define SDMMC_MAX_TRIAL 0x0000FFFFU + +#define SDMMC_ALLZERO 0x00000000U + +#define SDMMC_WIDE_BUS_SUPPORT 0x00040000U +#define SDMMC_SINGLE_BUS_SUPPORT 0x00010000U +#define SDMMC_CARD_LOCKED 0x02000000U + +#define SDMMC_DATATIMEOUT 0xFFFFFFFFU + +#define SDMMC_0TO7BITS 0x000000FFU +#define SDMMC_8TO15BITS 0x0000FF00U +#define SDMMC_16TO23BITS 0x00FF0000U +#define SDMMC_24TO31BITS 0xFF000000U +#define SDMMC_MAX_DATA_LENGTH 0x01FFFFFFU + +#define SDMMC_HALFFIFO 0x00000008U +#define SDMMC_HALFFIFOBYTES 0x00000020U + +/** + * @brief Command Class supported + */ +#define SDIO_CCCC_ERASE 0x00000020U + +#define SDIO_CMDTIMEOUT 5000U /* Command send and response timeout */ +#define SDIO_MAXERASETIMEOUT 63000U /* Max erase Timeout 63 s */ + + +/** @defgroup SDIO_LL_Clock_Edge Clock Edge + * @{ + */ +#define SDIO_CLOCK_EDGE_RISING 0x00000000U +#define SDIO_CLOCK_EDGE_FALLING SDIO_CLKCR_NEGEDGE + +#define IS_SDIO_CLOCK_EDGE(EDGE) (((EDGE) == SDIO_CLOCK_EDGE_RISING) || \ + ((EDGE) == SDIO_CLOCK_EDGE_FALLING)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Clock_Bypass Clock Bypass + * @{ + */ +#define SDIO_CLOCK_BYPASS_DISABLE 0x00000000U +#define SDIO_CLOCK_BYPASS_ENABLE SDIO_CLKCR_BYPASS + +#define IS_SDIO_CLOCK_BYPASS(BYPASS) (((BYPASS) == SDIO_CLOCK_BYPASS_DISABLE) || \ + ((BYPASS) == SDIO_CLOCK_BYPASS_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Clock_Power_Save Clock Power Saving + * @{ + */ +#define SDIO_CLOCK_POWER_SAVE_DISABLE 0x00000000U +#define SDIO_CLOCK_POWER_SAVE_ENABLE SDIO_CLKCR_PWRSAV + +#define IS_SDIO_CLOCK_POWER_SAVE(SAVE) (((SAVE) == SDIO_CLOCK_POWER_SAVE_DISABLE) || \ + ((SAVE) == SDIO_CLOCK_POWER_SAVE_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Bus_Wide Bus Width + * @{ + */ +#define SDIO_BUS_WIDE_1B 0x00000000U +#define SDIO_BUS_WIDE_4B SDIO_CLKCR_WIDBUS_0 +#define SDIO_BUS_WIDE_8B SDIO_CLKCR_WIDBUS_1 + +#define IS_SDIO_BUS_WIDE(WIDE) (((WIDE) == SDIO_BUS_WIDE_1B) || \ + ((WIDE) == SDIO_BUS_WIDE_4B) || \ + ((WIDE) == SDIO_BUS_WIDE_8B)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Hardware_Flow_Control Hardware Flow Control + * @{ + */ +#define SDIO_HARDWARE_FLOW_CONTROL_DISABLE 0x00000000U +#define SDIO_HARDWARE_FLOW_CONTROL_ENABLE SDIO_CLKCR_HWFC_EN + +#define IS_SDIO_HARDWARE_FLOW_CONTROL(CONTROL) (((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_DISABLE) || \ + ((CONTROL) == SDIO_HARDWARE_FLOW_CONTROL_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Clock_Division Clock Division + * @{ + */ +#define IS_SDIO_CLKDIV(DIV) ((DIV) <= 0xFFU) +/** + * @} + */ + +/** @defgroup SDIO_LL_Command_Index Command Index + * @{ + */ +#define IS_SDIO_CMD_INDEX(INDEX) ((INDEX) < 0x40U) +/** + * @} + */ + +/** @defgroup SDIO_LL_Response_Type Response Type + * @{ + */ +#define SDIO_RESPONSE_NO 0x00000000U +#define SDIO_RESPONSE_SHORT SDIO_CMD_WAITRESP_0 +#define SDIO_RESPONSE_LONG SDIO_CMD_WAITRESP + +#define IS_SDIO_RESPONSE(RESPONSE) (((RESPONSE) == SDIO_RESPONSE_NO) || \ + ((RESPONSE) == SDIO_RESPONSE_SHORT) || \ + ((RESPONSE) == SDIO_RESPONSE_LONG)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Wait_Interrupt_State Wait Interrupt + * @{ + */ +#define SDIO_WAIT_NO 0x00000000U +#define SDIO_WAIT_IT SDIO_CMD_WAITINT +#define SDIO_WAIT_PEND SDIO_CMD_WAITPEND + +#define IS_SDIO_WAIT(WAIT) (((WAIT) == SDIO_WAIT_NO) || \ + ((WAIT) == SDIO_WAIT_IT) || \ + ((WAIT) == SDIO_WAIT_PEND)) +/** + * @} + */ + +/** @defgroup SDIO_LL_CPSM_State CPSM State + * @{ + */ +#define SDIO_CPSM_DISABLE 0x00000000U +#define SDIO_CPSM_ENABLE SDIO_CMD_CPSMEN + +#define IS_SDIO_CPSM(CPSM) (((CPSM) == SDIO_CPSM_DISABLE) || \ + ((CPSM) == SDIO_CPSM_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Response_Registers Response Register + * @{ + */ +#define SDIO_RESP1 0x00000000U +#define SDIO_RESP2 0x00000004U +#define SDIO_RESP3 0x00000008U +#define SDIO_RESP4 0x0000000CU + +#define IS_SDIO_RESP(RESP) (((RESP) == SDIO_RESP1) || \ + ((RESP) == SDIO_RESP2) || \ + ((RESP) == SDIO_RESP3) || \ + ((RESP) == SDIO_RESP4)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Data_Length Data Lenght + * @{ + */ +#define IS_SDIO_DATA_LENGTH(LENGTH) ((LENGTH) <= 0x01FFFFFFU) +/** + * @} + */ + +/** @defgroup SDIO_LL_Data_Block_Size Data Block Size + * @{ + */ +#define SDIO_DATABLOCK_SIZE_1B 0x00000000U +#define SDIO_DATABLOCK_SIZE_2B SDIO_DCTRL_DBLOCKSIZE_0 +#define SDIO_DATABLOCK_SIZE_4B SDIO_DCTRL_DBLOCKSIZE_1 +#define SDIO_DATABLOCK_SIZE_8B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1) +#define SDIO_DATABLOCK_SIZE_16B SDIO_DCTRL_DBLOCKSIZE_2 +#define SDIO_DATABLOCK_SIZE_32B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2) +#define SDIO_DATABLOCK_SIZE_64B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2) +#define SDIO_DATABLOCK_SIZE_128B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2) +#define SDIO_DATABLOCK_SIZE_256B SDIO_DCTRL_DBLOCKSIZE_3 +#define SDIO_DATABLOCK_SIZE_512B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_1024B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_2048B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_4096B (SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_8192B (SDIO_DCTRL_DBLOCKSIZE_0|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) +#define SDIO_DATABLOCK_SIZE_16384B (SDIO_DCTRL_DBLOCKSIZE_1|SDIO_DCTRL_DBLOCKSIZE_2|SDIO_DCTRL_DBLOCKSIZE_3) + +#define IS_SDIO_BLOCK_SIZE(SIZE) (((SIZE) == SDIO_DATABLOCK_SIZE_1B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_2B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_4B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_8B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_16B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_32B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_64B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_128B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_256B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_512B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_1024B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_2048B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_4096B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_8192B) || \ + ((SIZE) == SDIO_DATABLOCK_SIZE_16384B)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Transfer_Direction Transfer Direction + * @{ + */ +#define SDIO_TRANSFER_DIR_TO_CARD 0x00000000U +#define SDIO_TRANSFER_DIR_TO_SDIO SDIO_DCTRL_DTDIR + +#define IS_SDIO_TRANSFER_DIR(DIR) (((DIR) == SDIO_TRANSFER_DIR_TO_CARD) || \ + ((DIR) == SDIO_TRANSFER_DIR_TO_SDIO)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Transfer_Type Transfer Type + * @{ + */ +#define SDIO_TRANSFER_MODE_BLOCK 0x00000000U +#define SDIO_TRANSFER_MODE_STREAM SDIO_DCTRL_DTMODE + +#define IS_SDIO_TRANSFER_MODE(MODE) (((MODE) == SDIO_TRANSFER_MODE_BLOCK) || \ + ((MODE) == SDIO_TRANSFER_MODE_STREAM)) +/** + * @} + */ + +/** @defgroup SDIO_LL_DPSM_State DPSM State + * @{ + */ +#define SDIO_DPSM_DISABLE 0x00000000U +#define SDIO_DPSM_ENABLE SDIO_DCTRL_DTEN + +#define IS_SDIO_DPSM(DPSM) (((DPSM) == SDIO_DPSM_DISABLE) ||\ + ((DPSM) == SDIO_DPSM_ENABLE)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Read_Wait_Mode Read Wait Mode + * @{ + */ +#define SDIO_READ_WAIT_MODE_DATA2 0x00000000U +#define SDIO_READ_WAIT_MODE_CLK (SDIO_DCTRL_RWMOD) + +#define IS_SDIO_READWAIT_MODE(MODE) (((MODE) == SDIO_READ_WAIT_MODE_CLK) || \ + ((MODE) == SDIO_READ_WAIT_MODE_DATA2)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Interrupt_sources Interrupt Sources + * @{ + */ +#define SDIO_IT_CCRCFAIL SDIO_STA_CCRCFAIL +#define SDIO_IT_DCRCFAIL SDIO_STA_DCRCFAIL +#define SDIO_IT_CTIMEOUT SDIO_STA_CTIMEOUT +#define SDIO_IT_DTIMEOUT SDIO_STA_DTIMEOUT +#define SDIO_IT_TXUNDERR SDIO_STA_TXUNDERR +#define SDIO_IT_RXOVERR SDIO_STA_RXOVERR +#define SDIO_IT_CMDREND SDIO_STA_CMDREND +#define SDIO_IT_CMDSENT SDIO_STA_CMDSENT +#define SDIO_IT_DATAEND SDIO_STA_DATAEND +#define SDIO_IT_STBITERR SDIO_STA_STBITERR +#define SDIO_IT_DBCKEND SDIO_STA_DBCKEND +#define SDIO_IT_CMDACT SDIO_STA_CMDACT +#define SDIO_IT_TXACT SDIO_STA_TXACT +#define SDIO_IT_RXACT SDIO_STA_RXACT +#define SDIO_IT_TXFIFOHE SDIO_STA_TXFIFOHE +#define SDIO_IT_RXFIFOHF SDIO_STA_RXFIFOHF +#define SDIO_IT_TXFIFOF SDIO_STA_TXFIFOF +#define SDIO_IT_RXFIFOF SDIO_STA_RXFIFOF +#define SDIO_IT_TXFIFOE SDIO_STA_TXFIFOE +#define SDIO_IT_RXFIFOE SDIO_STA_RXFIFOE +#define SDIO_IT_TXDAVL SDIO_STA_TXDAVL +#define SDIO_IT_RXDAVL SDIO_STA_RXDAVL +#define SDIO_IT_SDIOIT SDIO_STA_SDIOIT +#define SDIO_IT_CEATAEND SDIO_STA_CEATAEND +/** + * @} + */ + +/** @defgroup SDIO_LL_Flags Flags + * @{ + */ +#define SDIO_FLAG_CCRCFAIL SDIO_STA_CCRCFAIL +#define SDIO_FLAG_DCRCFAIL SDIO_STA_DCRCFAIL +#define SDIO_FLAG_CTIMEOUT SDIO_STA_CTIMEOUT +#define SDIO_FLAG_DTIMEOUT SDIO_STA_DTIMEOUT +#define SDIO_FLAG_TXUNDERR SDIO_STA_TXUNDERR +#define SDIO_FLAG_RXOVERR SDIO_STA_RXOVERR +#define SDIO_FLAG_CMDREND SDIO_STA_CMDREND +#define SDIO_FLAG_CMDSENT SDIO_STA_CMDSENT +#define SDIO_FLAG_DATAEND SDIO_STA_DATAEND +#define SDIO_FLAG_STBITERR SDIO_STA_STBITERR +#define SDIO_FLAG_DBCKEND SDIO_STA_DBCKEND +#define SDIO_FLAG_CMDACT SDIO_STA_CMDACT +#define SDIO_FLAG_TXACT SDIO_STA_TXACT +#define SDIO_FLAG_RXACT SDIO_STA_RXACT +#define SDIO_FLAG_TXFIFOHE SDIO_STA_TXFIFOHE +#define SDIO_FLAG_RXFIFOHF SDIO_STA_RXFIFOHF +#define SDIO_FLAG_TXFIFOF SDIO_STA_TXFIFOF +#define SDIO_FLAG_RXFIFOF SDIO_STA_RXFIFOF +#define SDIO_FLAG_TXFIFOE SDIO_STA_TXFIFOE +#define SDIO_FLAG_RXFIFOE SDIO_STA_RXFIFOE +#define SDIO_FLAG_TXDAVL SDIO_STA_TXDAVL +#define SDIO_FLAG_RXDAVL SDIO_STA_RXDAVL +#define SDIO_FLAG_SDIOIT SDIO_STA_SDIOIT +#define SDIO_FLAG_CEATAEND SDIO_STA_CEATAEND +#define SDIO_STATIC_FLAGS ((uint32_t)(SDIO_FLAG_CCRCFAIL | SDIO_FLAG_DCRCFAIL | SDIO_FLAG_CTIMEOUT |\ + SDIO_FLAG_DTIMEOUT | SDIO_FLAG_TXUNDERR | SDIO_FLAG_RXOVERR |\ + SDIO_FLAG_CMDREND | SDIO_FLAG_CMDSENT | SDIO_FLAG_DATAEND |\ + SDIO_FLAG_DBCKEND)) +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup SDIO_LL_Exported_macros SDIO_LL Exported Macros + * @{ + */ + +/** @defgroup SDMMC_LL_Alias_Region Bit Address in the alias region + * @{ + */ +/* ------------ SDIO registers bit address in the alias region -------------- */ +#define SDIO_OFFSET (SDIO_BASE - PERIPH_BASE) + +/* --- CLKCR Register ---*/ +/* Alias word address of CLKEN bit */ +#define CLKCR_OFFSET (SDIO_OFFSET + 0x04U) +#define CLKEN_BITNUMBER 0x08U +#define CLKCR_CLKEN_BB (PERIPH_BB_BASE + (CLKCR_OFFSET * 32U) + (CLKEN_BITNUMBER * 4U)) + +/* --- CMD Register ---*/ +/* Alias word address of SDIOSUSPEND bit */ +#define CMD_OFFSET (SDIO_OFFSET + 0x0CU) +#define SDIOSUSPEND_BITNUMBER 0x0BU +#define CMD_SDIOSUSPEND_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (SDIOSUSPEND_BITNUMBER * 4U)) + +/* Alias word address of ENCMDCOMPL bit */ +#define ENCMDCOMPL_BITNUMBER 0x0CU +#define CMD_ENCMDCOMPL_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ENCMDCOMPL_BITNUMBER * 4U)) + +/* Alias word address of NIEN bit */ +#define NIEN_BITNUMBER 0x0DU +#define CMD_NIEN_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (NIEN_BITNUMBER * 4U)) + +/* Alias word address of ATACMD bit */ +#define ATACMD_BITNUMBER 0x0EU +#define CMD_ATACMD_BB (PERIPH_BB_BASE + (CMD_OFFSET * 32U) + (ATACMD_BITNUMBER * 4U)) + +/* --- DCTRL Register ---*/ +/* Alias word address of DMAEN bit */ +#define DCTRL_OFFSET (SDIO_OFFSET + 0x2CU) +#define DMAEN_BITNUMBER 0x03U +#define DCTRL_DMAEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (DMAEN_BITNUMBER * 4U)) + +/* Alias word address of RWSTART bit */ +#define RWSTART_BITNUMBER 0x08U +#define DCTRL_RWSTART_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTART_BITNUMBER * 4U)) + +/* Alias word address of RWSTOP bit */ +#define RWSTOP_BITNUMBER 0x09U +#define DCTRL_RWSTOP_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWSTOP_BITNUMBER * 4U)) + +/* Alias word address of RWMOD bit */ +#define RWMOD_BITNUMBER 0x0AU +#define DCTRL_RWMOD_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (RWMOD_BITNUMBER * 4U)) + +/* Alias word address of SDIOEN bit */ +#define SDIOEN_BITNUMBER 0x0BU +#define DCTRL_SDIOEN_BB (PERIPH_BB_BASE + (DCTRL_OFFSET * 32U) + (SDIOEN_BITNUMBER * 4U)) +/** + * @} + */ + +/** @defgroup SDIO_LL_Register Bits And Addresses Definitions + * @brief SDIO_LL registers bit address in the alias region + * @{ + */ +/* ---------------------- SDIO registers bit mask --------------------------- */ +/* --- CLKCR Register ---*/ +/* CLKCR register clear mask */ +#define CLKCR_CLEAR_MASK ((uint32_t)(SDIO_CLKCR_CLKDIV | SDIO_CLKCR_PWRSAV |\ + SDIO_CLKCR_BYPASS | SDIO_CLKCR_WIDBUS |\ + SDIO_CLKCR_NEGEDGE | SDIO_CLKCR_HWFC_EN)) + +/* --- DCTRL Register ---*/ +/* SDIO DCTRL Clear Mask */ +#define DCTRL_CLEAR_MASK ((uint32_t)(SDIO_DCTRL_DTEN | SDIO_DCTRL_DTDIR |\ + SDIO_DCTRL_DTMODE | SDIO_DCTRL_DBLOCKSIZE)) + +/* --- CMD Register ---*/ +/* CMD Register clear mask */ +#define CMD_CLEAR_MASK ((uint32_t)(SDIO_CMD_CMDINDEX | SDIO_CMD_WAITRESP |\ + SDIO_CMD_WAITINT | SDIO_CMD_WAITPEND |\ + SDIO_CMD_CPSMEN | SDIO_CMD_SDIOSUSPEND)) + +/* SDIO Initialization Frequency (400KHz max) */ +#define SDIO_INIT_CLK_DIV ((uint8_t)0x76) + +/* SDIO Data Transfer Frequency (25MHz max) */ +#define SDIO_TRANSFER_CLK_DIV ((uint8_t)0x0) + +/** + * @} + */ + +/** @defgroup SDIO_LL_Interrupt_Clock Interrupt And Clock Configuration + * @brief macros to handle interrupts and specific clock configurations + * @{ + */ + +/** + * @brief Enable the SDIO device. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_ENABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = ENABLE) + +/** + * @brief Disable the SDIO device. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_DISABLE(__INSTANCE__) (*(__IO uint32_t *)CLKCR_CLKEN_BB = DISABLE) + +/** + * @brief Enable the SDIO DMA transfer. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_DMA_ENABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = ENABLE) +/** + * @brief Disable the SDIO DMA transfer. + * @param __INSTANCE__: SDIO Instance + * @retval None + */ +#define __SDIO_DMA_DISABLE(__INSTANCE__) (*(__IO uint32_t *)DCTRL_DMAEN_BB = DISABLE) + +/** + * @brief Enable the SDIO device interrupt. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__ : specifies the SDIO interrupt sources to be enabled. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @retval None + */ +#define __SDIO_ENABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK |= (__INTERRUPT__)) + +/** + * @brief Disable the SDIO device interrupt. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__ : specifies the SDIO interrupt sources to be disabled. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @retval None + */ +#define __SDIO_DISABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK &= ~(__INTERRUPT__)) + +/** + * @brief Checks whether the specified SDIO flag is set or not. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) + * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) + * @arg SDIO_FLAG_CTIMEOUT: Command response timeout + * @arg SDIO_FLAG_DTIMEOUT: Data timeout + * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error + * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error + * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) + * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) + * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) + * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) + * @arg SDIO_FLAG_CMDACT: Command transfer in progress + * @arg SDIO_FLAG_TXACT: Data transmit in progress + * @arg SDIO_FLAG_RXACT: Data receive in progress + * @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty + * @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full + * @arg SDIO_FLAG_TXFIFOF: Transmit FIFO full + * @arg SDIO_FLAG_RXFIFOF: Receive FIFO full + * @arg SDIO_FLAG_TXFIFOE: Transmit FIFO empty + * @arg SDIO_FLAG_RXFIFOE: Receive FIFO empty + * @arg SDIO_FLAG_TXDAVL: Data available in transmit FIFO + * @arg SDIO_FLAG_RXDAVL: Data available in receive FIFO + * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received + * @retval The new state of SDIO_FLAG (SET or RESET). + */ +#define __SDIO_GET_FLAG(__INSTANCE__, __FLAG__) (((__INSTANCE__)->STA &(__FLAG__)) != RESET) + + +/** + * @brief Clears the SDIO pending flags. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __FLAG__: specifies the flag to clear. + * This parameter can be one or a combination of the following values: + * @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed) + * @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) + * @arg SDIO_FLAG_CTIMEOUT: Command response timeout + * @arg SDIO_FLAG_DTIMEOUT: Data timeout + * @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error + * @arg SDIO_FLAG_RXOVERR: Received FIFO overrun error + * @arg SDIO_FLAG_CMDREND: Command response received (CRC check passed) + * @arg SDIO_FLAG_CMDSENT: Command sent (no response required) + * @arg SDIO_FLAG_DATAEND: Data end (data counter, SDIDCOUNT, is zero) + * @arg SDIO_FLAG_DBCKEND: Data block sent/received (CRC check passed) + * @arg SDIO_FLAG_SDIOIT: SD I/O interrupt received + * @retval None + */ +#define __SDIO_CLEAR_FLAG(__INSTANCE__, __FLAG__) ((__INSTANCE__)->ICR = (__FLAG__)) + +/** + * @brief Checks whether the specified SDIO interrupt has occurred or not. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__: specifies the SDIO interrupt source to check. + * This parameter can be one of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIDCOUNT, is zero) interrupt + * @arg SDIO_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt + * @arg SDIO_IT_CMDACT: Command transfer in progress interrupt + * @arg SDIO_IT_TXACT: Data transmit in progress interrupt + * @arg SDIO_IT_RXACT: Data receive in progress interrupt + * @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt + * @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt + * @arg SDIO_IT_TXFIFOF: Transmit FIFO full interrupt + * @arg SDIO_IT_RXFIFOF: Receive FIFO full interrupt + * @arg SDIO_IT_TXFIFOE: Transmit FIFO empty interrupt + * @arg SDIO_IT_RXFIFOE: Receive FIFO empty interrupt + * @arg SDIO_IT_TXDAVL: Data available in transmit FIFO interrupt + * @arg SDIO_IT_RXDAVL: Data available in receive FIFO interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @retval The new state of SDIO_IT (SET or RESET). + */ +#define __SDIO_GET_IT (__INSTANCE__, __INTERRUPT__) (((__INSTANCE__)->STA &(__INTERRUPT__)) == (__INTERRUPT__)) + +/** + * @brief Clears the SDIO's interrupt pending bits. + * @param __INSTANCE__ : Pointer to SDIO register base + * @param __INTERRUPT__: specifies the interrupt pending bit to clear. + * This parameter can be one or a combination of the following values: + * @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt + * @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt + * @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt + * @arg SDIO_IT_DTIMEOUT: Data timeout interrupt + * @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt + * @arg SDIO_IT_RXOVERR: Received FIFO overrun error interrupt + * @arg SDIO_IT_CMDREND: Command response received (CRC check passed) interrupt + * @arg SDIO_IT_CMDSENT: Command sent (no response required) interrupt + * @arg SDIO_IT_DATAEND: Data end (data counter, SDIO_DCOUNT, is zero) interrupt + * @arg SDIO_IT_SDIOIT: SD I/O interrupt received interrupt + * @retval None + */ +#define __SDIO_CLEAR_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->ICR = (__INTERRUPT__)) + +/** + * @brief Enable Start the SD I/O Read Wait operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_START_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = ENABLE) + +/** + * @brief Disable Start the SD I/O Read Wait operations. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_START_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTART_BB = DISABLE) + +/** + * @brief Enable Start the SD I/O Read Wait operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_STOP_READWAIT_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = ENABLE) + +/** + * @brief Disable Stop the SD I/O Read Wait operations. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_STOP_READWAIT_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_RWSTOP_BB = DISABLE) + +/** + * @brief Enable the SD I/O Mode Operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_OPERATION_ENABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = ENABLE) + +/** + * @brief Disable the SD I/O Mode Operation. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_OPERATION_DISABLE(__INSTANCE__) (*(__IO uint32_t *) DCTRL_SDIOEN_BB = DISABLE) + +/** + * @brief Enable the SD I/O Suspend command sending. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_SUSPEND_CMD_ENABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = ENABLE) + +/** + * @brief Disable the SD I/O Suspend command sending. + * @param __INSTANCE__ : Pointer to SDIO register base + * @retval None + */ +#define __SDIO_SUSPEND_CMD_DISABLE(__INSTANCE__) (*(__IO uint32_t *) CMD_SDIOSUSPEND_BB = DISABLE) + +#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\ + defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\ + defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) +/** + * @brief Enable the command completion signal. + * @retval None + */ +#define __SDIO_CEATA_CMD_COMPLETION_ENABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = ENABLE) + +/** + * @brief Disable the command completion signal. + * @retval None + */ +#define __SDIO_CEATA_CMD_COMPLETION_DISABLE() (*(__IO uint32_t *) CMD_ENCMDCOMPL_BB = DISABLE) + +/** + * @brief Enable the CE-ATA interrupt. + * @retval None + */ +#define __SDIO_CEATA_ENABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)0U) + +/** + * @brief Disable the CE-ATA interrupt. + * @retval None + */ +#define __SDIO_CEATA_DISABLE_IT() (*(__IO uint32_t *) CMD_NIEN_BB = (uint32_t)1U) + +/** + * @brief Enable send CE-ATA command (CMD61). + * @retval None + */ +#define __SDIO_CEATA_SENDCMD_ENABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = ENABLE) + +/** + * @brief Disable send CE-ATA command (CMD61). + * @retval None + */ +#define __SDIO_CEATA_SENDCMD_DISABLE() (*(__IO uint32_t *) CMD_ATACMD_BB = DISABLE) +#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE ||\ + STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ + +/** + * @} + */ + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup SDMMC_LL_Exported_Functions + * @{ + */ + +/* Initialization/de-initialization functions **********************************/ +/** @addtogroup HAL_SDMMC_LL_Group1 + * @{ + */ +HAL_StatusTypeDef SDIO_Init(SDIO_TypeDef *SDIOx, SDIO_InitTypeDef Init); +/** + * @} + */ + +/* I/O operation functions *****************************************************/ +/** @addtogroup HAL_SDMMC_LL_Group2 + * @{ + */ +uint32_t SDIO_ReadFIFO(SDIO_TypeDef *SDIOx); +HAL_StatusTypeDef SDIO_WriteFIFO(SDIO_TypeDef *SDIOx, uint32_t *pWriteData); +/** + * @} + */ + +/* Peripheral Control functions ************************************************/ +/** @addtogroup HAL_SDMMC_LL_Group3 + * @{ + */ +HAL_StatusTypeDef SDIO_PowerState_ON(SDIO_TypeDef *SDIOx); +HAL_StatusTypeDef SDIO_PowerState_OFF(SDIO_TypeDef *SDIOx); +uint32_t SDIO_GetPowerState(SDIO_TypeDef *SDIOx); + +/* Command path state machine (CPSM) management functions */ +HAL_StatusTypeDef SDIO_SendCommand(SDIO_TypeDef *SDIOx, SDIO_CmdInitTypeDef *Command); +uint8_t SDIO_GetCommandResponse(SDIO_TypeDef *SDIOx); +uint32_t SDIO_GetResponse(SDIO_TypeDef *SDIOx, uint32_t Response); + +/* Data path state machine (DPSM) management functions */ +HAL_StatusTypeDef SDIO_ConfigData(SDIO_TypeDef *SDIOx, SDIO_DataInitTypeDef* Data); +uint32_t SDIO_GetDataCounter(SDIO_TypeDef *SDIOx); +uint32_t SDIO_GetFIFOCount(SDIO_TypeDef *SDIOx); + +/* SDMMC Cards mode management functions */ +HAL_StatusTypeDef SDIO_SetSDMMCReadWaitMode(SDIO_TypeDef *SDIOx, uint32_t SDIO_ReadWaitMode); + +/* SDMMC Commands management functions */ +uint32_t SDMMC_CmdBlockLength(SDIO_TypeDef *SDIOx, uint32_t BlockSize); +uint32_t SDMMC_CmdReadSingleBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd); +uint32_t SDMMC_CmdReadMultiBlock(SDIO_TypeDef *SDIOx, uint32_t ReadAdd); +uint32_t SDMMC_CmdWriteSingleBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd); +uint32_t SDMMC_CmdWriteMultiBlock(SDIO_TypeDef *SDIOx, uint32_t WriteAdd); +uint32_t SDMMC_CmdSDEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd); +uint32_t SDMMC_CmdSDEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd); +uint32_t SDMMC_CmdErase(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdStopTransfer(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdSelDesel(SDIO_TypeDef *SDIOx, uint64_t Addr); +uint32_t SDMMC_CmdGoIdleState(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdOperCond(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdAppCommand(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdAppOperCommand(SDIO_TypeDef *SDIOx, uint32_t SdType); +uint32_t SDMMC_CmdBusWidth(SDIO_TypeDef *SDIOx, uint32_t BusWidth); +uint32_t SDMMC_CmdSendSCR(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdSendCID(SDIO_TypeDef *SDIOx); +uint32_t SDMMC_CmdSendCSD(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdSetRelAdd(SDIO_TypeDef *SDIOx, uint16_t *pRCA); +uint32_t SDMMC_CmdSendStatus(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdStatusRegister(SDIO_TypeDef *SDIOx); + +uint32_t SDMMC_CmdOpCondition(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdSwitch(SDIO_TypeDef *SDIOx, uint32_t Argument); +uint32_t SDMMC_CmdEraseStartAdd(SDIO_TypeDef *SDIOx, uint32_t StartAdd); +uint32_t SDMMC_CmdEraseEndAdd(SDIO_TypeDef *SDIOx, uint32_t EndAdd); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || + STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx || STM32F412Zx || STM32F412Vx || + STM32F412Rx || STM32F412Cx || STM32F413xx || STM32F423xx */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_LL_SDMMC_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ +