KL25Z Comparator library
Dependents: ComparatorIn_demo TEMT6200_demo 05_comparator_demo 05_comparator_demo ... more
KL25Z Comparator library
Comparator features
- Operational over the entire supply range
- Inputs may range from rail to rail
- Programmable hysteresis control
- Selectable interrupt on rising-edge, falling-edge, or both rising or falling edges of the comparator output
- Selectable inversion on comparator output
- Capability to produce a wide range of outputs such as:
- Sampled
- Windowed, which is ideal for certain PWM zero-crossing-detection applications
- Digitally filtered:
- Filter can be bypassed
- Can be clocked via external SAMPLE signal or scaled bus clock
- Filter can be bypassed
- Sampled
- External hysteresis can be used at the same time that the output filter is used for internal functions
- Two software selectable performance levels:
- Shorter propagation delay at the expense of higher power
- Low power, with longer propagation delay
- Shorter propagation delay at the expense of higher power
- DMA transfer support not yet implemented in this library
- A comparison event can be selected to trigger a DMA transfer
- A comparison event can be selected to trigger a DMA transfer
- Functional in all modes of operation
- The window and filter functions are not available in the following modes:
- Stop
- VLPS
- LLS
- VLLSx
Block diagram
Introduction
This library allows us to create comparator objects between different inputs.
The comparator +
and -
inputs can be routed to one out of eight reference inputs (see table).
Input selection
Pin name | # | MUX input | CMP0 | Comment |
---|---|---|---|---|
PTC6 | 000 | IN0 | CMP0_IN0 | |
PTC7 | 001 | IN1 | CMP0_IN1 | |
PTC8 | 010 | IN2 | CMP0_IN2 | |
PTC9 | 011 | IN3 | CMP0_IN3 | |
PTE30 | 100 | IN4 | CMP0_IN4 | 12-bit DAC0 |
PTE29 | 101 | IN5 | CMP0_IN5 | |
110 | IN6 | 1V internal Bandgap* | ||
NC | 111 | IN7 | internal 6-bit DAC0 | |
(table 1) |
* Not yet implemented
Using the library
Selecting pins on initialisation
Upon initialisation, the comparator registers are set to following values:
CMP0->CR0 = 0x00; // Filter and digital hysteresis disabled CMP0->CR1 = 0x17; // Continuous mode, high-speed compare, unfiltered output, output pin disabled CMP0->FPR = 0x00; // Filter disabled CMP0->SCR = 0x06; // Disable all interrupts and clear flags (flags are cleared by this write) CMP0->DACCR = 0xE0; // DAC enabled, Vdd is 6bit reference, threshold set to 1/2 of full-scale (1.65V)
The library accepts two input parameters:
example:
ComparatorIn compi(PTC8, NC);
- First parameter :
+
input pin.
- Second parameter :
-
input pin.
Every pin from the 'Pin name' column in (table 1) can be selected.
notes
- IN6 (internal 1V bandgap reference) has no pin name and is not selectable on init.
However, we can use the SwitchPlus and SwitchMin functions to change the corresponding input to IN6. - There are two special cases for the input parameters:
NC
: Connect the internal 6-bit DAC0 to IN7.PTE30
: configures PTE30 as 12-bit DAC0 output and connect to IN4.
IMPORTANT: Make sure no external output is connected to PTE30 when you declare this pin, otherwise you WILL destroy the external device and/or the CPU.
Example
Following code demonstrates interrupt callback
and polling mode
.
Note: Polling the comparator this way won't always trigger the printf because of the wait() instructions (if we go above and below the threshold during the wait() time, then the polling cannot not see this change).
/*********************************************************** CODE EXAMPLE FOR AMBIENT LIGHT SENSOR ON KL25Z + Wi-Go BOARD ***********************************************************/ #include "ComparatorIn.h" #include "mbed.h" DigitalOut blinker(LED_BLUE); DigitalOut cmpled(LED_GREEN); DigitalOut cmp_en (PTD5); AnalogIn cmp_lvl (PTB0); ComparatorIn compi(PTC8, NC); // in+ = PTC8, in- = internal 6-bit DAC // Comparator callback functions void cmp_rise_ISR(void) { cmpled = 0; } void cmp_fall_ISR(void) { cmpled = 1; } int main() { cmp_en = 1; cmpled = 1; compi.rising(&cmp_rise_ISR); // Set pointer to rising interrupt function compi.falling(&cmp_fall_ISR); // Set pointer to falling interrupt function compi.treshold(0.5); // Set comparator threshold to 1.65V = 32 * 3.3V / 64 while(1) { printf("Light sensor : %7.5f Volt\n",cmp_lvl*3.3); blinker = 1; wait(1); blinker = 0; wait(0.2); if (compi.status() == 0x01) { printf("*** Treshold reached : %7.5f\n",cmp_lvl*3.3); } } }
Notes
- When we enable the comparator interrupt, we need to declare user callback function(s) (rising and/or falling interrupt) AND initialise the function pointer(s).
example:
compi.rising(&cmp_rise_ISR); compi.falling(&cmp_fall_ISR);
- Currently, following functions are not yet implemented:
- On the fly MUX switching for
+
input (SwitchPlus function). - On the fly MUX switching for
-
input (SwitchMin function). - DMA transfer.
- On the fly MUX switching for
Diff: ComparatorIn.h
- Revision:
- 14:875486333dc2
- Parent:
- 13:2d499824ba05
- Child:
- 15:f340e0545b53
diff -r 2d499824ba05 -r 875486333dc2 ComparatorIn.h --- a/ComparatorIn.h Sat Jun 15 19:34:16 2013 +0000 +++ b/ComparatorIn.h Sun Jun 16 10:03:19 2013 +0000 @@ -183,17 +183,6 @@ */ void dma_en(unsigned char dmaen); - /** Comparator set Interrupt - * @param . Enables the CFR/CFF interrupt from the CMP. When this field is set, - * @param . an interrupt will be asserted when CFR/CFF is set. - * @param input RISING enable rising interrupt. - * @param input FALLING enable falling interrupt. - * @param input RISING enable rising and falling interrupts. - * @param input DISABLE no interrupts. - * @return none - */ - void int_en(unsigned char ien); - /** Analog Comparator Output * @param none * @return . Returns the current value of the Analog Comparator output, when read. @@ -283,15 +272,28 @@ */ void switch_min(unsigned char pinM); + /** Comparator enable/disable Interrupt + * @param 1 Enables the comparator ISR + * @param 0 Disabled the comparator ISR. + * @return none + */ + void int_en(bool ien); + /** - * Comparator ISR callback + * Comparator rising interrupt callback * * @param pointer to the user function to execute after IRQ assertion - * @return . CMP_SCR_CFR_MASK (rising edge interrupt) - * @return . CMP_SCR_CFF_MASK (falling edge interrupt) - * @return returns rising/falling interrupt flag (unsigned int) to user function + * @return none */ - void _callbackISR(void(*fptr)(unsigned int)); + void rising(void(*fptr)(void)); + + /** + * Comparator falling interrupt callback + * + * @param pointer to the user function to execute after IRQ assertion + * @return none + */ + void falling(void(*fptr)(void)); private: static const PinMap PinMap_CMP[7];