These are the examples provided for [[/users/frank26080115/libraries/LPC1700CMSIS_Lib/]] Note, the entire "program" is not compilable!
Diff: UART/UART1_FullModem/abstract.h
- Revision:
- 0:bf7b9fba3924
diff -r 000000000000 -r bf7b9fba3924 UART/UART1_FullModem/abstract.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/UART/UART1_FullModem/abstract.h Sun Mar 20 05:38:56 2011 +0000 @@ -0,0 +1,96 @@ + ******************** (C) COPYRIGHT 2010 NXPSemiconductors ******************* + * @file UART\UART1_FullModem\abstract.txt + * @author NXP MCU SW Application Team + * @version 2.0 + * @date + * @brief Description of the UART1_FullModem example. + ****************************************************************************** + * Software that is described herein is for illustrative purposes only + * which provides customers with programming information regarding the + * products. This software is supplied "AS IS" without any warranties. + * NXP Semiconductors assumes no responsibility or liability for the + * use of the software, conveys no license or title under any patent, + * copyright, or mask work right to the product. NXP Semiconductors + * reserves the right to make changes in the software without + * notification. NXP Semiconductors also make no representation or + * warranty that such application will be suitable for the specified + * use without further testing or modification. + ****************************************************************************** + +@Example description: + Purpose: + This is a simple UART example using UART1 will Full modem mode + Process: + Uart pin configuration: + - If using MCB1700 eval board, assign pin P2.0 - P2.7 for UART1 + - If using IAR 1768 KS board, assign pin P0.7 - P0.15 for UART2 + Configure UART using the following settings: + - Baudrate = 9600bps + - 8 data bit + - 1 Stop bit + - None parity + + After reset UART will send the welcome massage then start to receive the + character from PC and send back that character to PC. + +@Directory contents: + \EWARM: includes EWARM (IAR) project and configuration files + \Keil: includes RVMDK (Keil)project and configuration files + + lpc17xx_libcfg.h: Library configuration file - include needed driver library + for this example + makefile: Example's makefile (to build with GNU toolchain) + uart_fullmodem_test.c: Main program + +@How to run: + Hardware configuration: + This example was tested on: + Keil MCB1700 with LPC1768 vers.1 + These jumpers must be configured as following: + - VDDIO: ON + - VDDREGS: ON + - VBUS: ON + - AD0.2: ON + - LED: ON + - Remain jumpers: OFF + IAR LPC1768 KickStart vers.A + These jumpers must be configured as following: + - PWR_SEL: depend on power source + - DBG_EN : ON + - Remain jumpers: OFF + + UART FullModem connection + Because eval board does not wire all pins of UART1 to the COM1 port, + the signal on CTS, RTS might be in incorrect state for UART1 running. + In this case, CTS pin must be pulled-low + + MCB board: CTS pin is P2.2 + + IAR board: CTS pin is P0.17 + + + Running mode: + This example can run on RAM/ROM mode. + + Note: If want to burn hex file to board by using Flash Magic, these jumpers need + to be connected: + - MCB1700 with LPC1768 ver.1: + + RST: ON + + ISP: ON + - IAR LPC1768 KickStart vers.A: + + RST_E: ON + + ISP_E: ON + + (Please reference "LPC1000 Software Development Toolchain" - chapter 4 + "Creating and working with LPC1000CMSIS project" for more information) + + Step to run: + - Step 1: Build example. + - Step 2: Burn hex file into board (if run on ROM mode) + - Step 3: Connect UART1 on this board to COM port on your computer + - Step 5: Run example and using Serial display to see the result. + + (Pls see "LPC17xx Example Description" document - chapter "Examples > UART > UART1_FullModem" + for more details) + +@Tip: + - Open \EWARM\*.eww project file to run example on IAR + - Open \RVMDK\*.uvproj project file to run example on Keil