Diff: UART/UART1_FullModem/abstract.h

Revision:

0:bf7b9fba3924

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/UART/UART1_FullModem/abstract.h	Sun Mar 20 05:38:56 2011 +0000
@@ -0,0 +1,96 @@
+ ******************** (C) COPYRIGHT 2010 NXPSemiconductors *******************
+ * @file    UART\UART1_FullModem\abstract.txt 
+ * @author  NXP MCU SW Application Team
+ * @version 2.0
+ * @date    
+ * @brief   Description of the UART1_FullModem example.
+ ******************************************************************************
+ * Software that is described herein is for illustrative purposes only
+ * which provides customers with programming information regarding the
+ * products. This software is supplied "AS IS" without any warranties.
+ * NXP Semiconductors assumes no responsibility or liability for the
+ * use of the software, conveys no license or title under any patent,
+ * copyright, or mask work right to the product. NXP Semiconductors
+ * reserves the right to make changes in the software without
+ * notification. NXP Semiconductors also make no representation or
+ * warranty that such application will be suitable for the specified
+ * use without further testing or modification.
+ ******************************************************************************
+  
+@Example description:
+	Purpose:
+		This is a simple UART example using UART1 will Full modem mode
+	Process:
+		Uart pin configuration:
+			- If using MCB1700 eval board, assign pin P2.0 - P2.7 for UART1
+		 	- If using IAR 1768 KS board, assign pin P0.7 - P0.15 for UART2
+	 	Configure UART using the following settings:
+	 		- Baudrate = 9600bps
+	 		- 8 data bit
+	 		- 1 Stop bit
+	 		- None parity
+
+		After reset UART will send the welcome massage then start to receive the 
+		character from PC and send back that character to PC.
+		
+@Directory contents:
+	\EWARM: includes EWARM (IAR) project and configuration files
+	\Keil:	includes RVMDK (Keil)project and configuration files 
+	 
+	lpc17xx_libcfg.h: Library configuration file - include needed driver library 
+			for this example 
+	makefile: Example's makefile (to build with GNU toolchain)
+	uart_fullmodem_test.c: Main program
+
+@How to run:
+	Hardware configuration:		
+		This example was tested on:
+			Keil MCB1700 with LPC1768 vers.1
+				These jumpers must be configured as following:
+				- VDDIO: ON
+				- VDDREGS: ON 
+				- VBUS: ON
+				- AD0.2: ON
+				- LED: ON
+				- Remain jumpers: OFF
+			IAR LPC1768 KickStart vers.A
+				These jumpers must be configured as following:
+				- PWR_SEL: depend on power source
+				- DBG_EN : ON
+				- Remain jumpers: OFF
+							
+		UART FullModem connection
+				Because eval board does not wire all pins of UART1 to the COM1 port,
+				the signal on CTS, RTS might be in incorrect state for UART1 running.
+				In this case, CTS pin must be pulled-low	
+					+ MCB board: CTS pin is P2.2
+					+ IAR board: CTS pin is P0.17
+					
+	
+	Running mode:
+		This example can run on RAM/ROM mode.
+					
+		Note: If want to burn hex file to board by using Flash Magic, these jumpers need
+		to be connected:
+			- MCB1700 with LPC1768 ver.1:
+				+ RST: ON
+				+ ISP: ON
+			- IAR LPC1768 KickStart vers.A:
+				+ RST_E: ON
+				+ ISP_E: ON
+		
+		(Please reference "LPC1000 Software Development Toolchain" - chapter 4 
+		"Creating and working with LPC1000CMSIS project" for more information)
+	
+	Step to run:
+		- Step 1: Build example.
+		- Step 2: Burn hex file into board (if run on ROM mode)
+		- Step 3: Connect UART1 on this board to COM port on your computer
+		- Step 5: Run example and using Serial display to see the result.
+		
+		(Pls see "LPC17xx Example Description" document - chapter "Examples > UART > UART1_FullModem"
+		for more details)
+		
+@Tip:
+	- Open \EWARM\*.eww project file to run example on IAR
+	- Open \RVMDK\*.uvproj project file to run example on Keil