Francesco Pistone
/
FORIGO_Modula_V6_R2C_DE_HwV5
vo
iodefinition.hpp
- Committer:
- francescopistone
- Date:
- 2019-01-31
- Branch:
- V6_R2C_DE_HwV5_V0
- Revision:
- 12:523b5fe855a7
- Parent:
- 10:d85ed006056e
File content as of revision 12:523b5fe855a7:
Watchdog wd; #if defined(speedMaster) InterruptIn tractorSpeedRead(PB_1); // define interrupt pin for tractor speed calculation MASTER MODE DigitalOut quinconceOut(PA_5); // sincro per quinconcio out DigitalOut speedClock(PA_6); // define out for speed clock repeater InterruptIn DcEncoder(PB_2); // define input for reading speed of seed wheel with fixed 25 hole #else InterruptIn tractorSpeedRead(PB_6); // define interrupt pin for tractor speed calculation SLAVE MODE InterruptIn quinconceIn(PA_9); DigitalIn quinconceOut(PA_5,PullUp); // sincro per quinconcio out InterruptIn DcEncoder(PB_2); // define input for reading speed of seed wheel with fixed 25 hole DigitalOut speedClock(PA_6); // define out for speed clock repeater DigitalIn seedLevel(PB_1); // define input for reading seed level on tank #endif DigitalIn TBzeroPinInputRev(PB_11); // define input of reading zero position of distributor wheel DigitalIn seedWheelZeroPinInputRev(PB_12); // define input of reading zero position of seeding wheel InterruptIn seedCheck(PA_7); // define input for reading seed passage to picks DigitalIn buttonUser(PC_13); // pulsante su scheda InterruptIn pwmCheck(PB_13); PwmOut SDmotorPWM(PB_13); // define frequency command for seeding whell motor driver DigitalOut SDmotorInB(PB_14); // sd motor half bridge direction selector DigitalOut SDmotorInA(PB_15); // SD motor half bridge direction selector DigitalIn enDiag_A(PB_5); // SD motor fault condition input A DigitalIn enDiag_B(PB_4); // SD motor fault condition input A AnalogIn SDcurrent(PA_4); // SD power current feedback DigitalOut TBmotor_M1(PC_8); // TB motor step division M1 DigitalOut TBmotor_M2(PC_6); // TB motor step division M2 DigitalOut TBmotor_M3(PC_5); // TB motor step division M3 DigitalOut TBmotorRst(PC_4); // TB motor driver reset DigitalOut TBmotorStepOut(PB_3); // TB motor step command DigitalOut TBmotorDirecti(PA_10); // TB motor direction command /* #if defined(speedMaster) //DigitalOut led(LED1); // ATTENZIONE: LED1 E' SU PA5 / D13 #else DigitalOut led(PC_7); // ATTENZIONE: LED1 E' SU PA5 / D13 #endif */ //DigitalIn zeroRequestIn(PB_6); // define input of zero request for slave module //DigitalIn runRequestIn(PB_9); // define input of run request for slave module #if defined(canbusActive) CAN can1(PA_11,PA_12,100000); // CAN BUS channel for communication with other slave and master consolle int checkState=0; #endif CANMessage txMsg; CANMessage rxMsg; #if defined(pcSerial) Serial pc(USBTX, USBRX,250000); // serial channel for PC communication #else #if defined(speedTime) Serial pc(USBTX, USBRX,250000); // serial channel for PC communication #endif #endif