Esmacat HarmonicBionics / EsmacatShield

An Mbed library for an EtherCAT Arduino Shield developed by Esmacat to connect the larger Arduino ecosystem and other MCU boards capable of connecting a shield with an Arduino Uno form factor. EASE can easily turn an MCU board, including the Arduino ecosystem, into a cost-efficient EtherCAT slave subsystem in the larger EtherCAT system. Using EtherCAT communication, EASE can reliably communicate with other base boards through an EtherCAT master.

Information about Esmacat and EASE is provided in the link below. https://os.mbed.com/users/esmacat/code/EASE_Example/wiki/Homepage

EsmacatShield.cpp

Committer:
pratima_hb
Date:
2020-01-29
Revision:
1:b66c3e4ce9f5
Parent:
0:4a9e3331b131
Child:
2:77c2a6061e77

File content as of revision 1:b66c3e4ce9f5:

/**
  Copyright (c) 2020 https://www.esmacat.com/

  Licensed under the Apache License, Version 2.0 (the "License");
  you may not use this file except in compliance with the License.
  You may obtain a copy of the License at

    http://www.apache.org/licenses/LICENSE-2.0

  Unless required by applicable law or agreed to in writing, software
  distributed under the License is distributed on an "AS IS" BASIS,
  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  See the License for the specific language governing permissions and
  limitations under the License.

  EsmacatShield.cpp - Library for using EtherCAT Arduino Shield by Esmacat(EASE).
  Created by Esmacat, 01/22/2020

*******************************************************************************
* @file EsmacatShield.cpp
*******************************************************************************
*/

#include "EsmacatShield.h"

EsmacatShield::EsmacatShield(SPI &spi, DigitalOut &pin):ecat_spi(spi),ecat_cs(pin) 
{
     
}

void EsmacatShield::setup_spi()
{
    /*Chip must be deselected*/
    ecat_cs = 1;

  /*Setup the spi for 8 bit data, Mode 1,
    with a 3MHz clock rate*/
    ecat_spi.format(8,1);
    ecat_spi.frequency(3000000);
    
    /* Chip must be selected*/
    ecat_cs = 0;

}


void EsmacatShield::write_reg_value(int write_addr,int value, bool led_on)
{
  uint8_t v1,v2;
  // Chip must be selected
  ecat_cs = 0;
  wait_us(2000);                       //sleep for 2 ms;
  write_addr = write_addr <<3;
  if (led_on)
  {
    ecat_spi.write(((EASE_WRITE_REG|write_addr)| EASE_LED_ON)& EASE_SINGLE_SHOT);
  }
  else
  {
    ecat_spi.write((EASE_WRITE_REG|write_addr)& EASE_LED_OFF & EASE_SINGLE_SHOT); 
  }
  v1 = (value&0xFF00) >> 8;
  v2 = (value&0x00FF);
  ecat_spi.write(v1);
  ecat_spi.write(v2);
  // Chip must be deselected
  ecat_cs = 1;
  wait_us(2000);                       //sleep for 2 ms;
}

int* EsmacatShield::get_ecat_registers(int regs[8]) {
  regs[0] = read_reg_value(1);
  regs[1] = read_reg_value(2);
  regs[2] = read_reg_value(3);
  regs[3] = read_reg_value(4);
  regs[4] = read_reg_value(5);
  regs[5] = read_reg_value(6);
  regs[6] = read_reg_value(7);
  regs[7] = read_reg_value(0);
  return(regs);
}

int EsmacatShield::read_reg_value(int read_addr)
{
  uint16_t v2,v3;
  // Chip must be selected
  ecat_cs = 0;
  wait_us(2000);                       //sleep for 2 ms;
  read_addr = read_addr <<3;
  ecat_spi.write( EASE_READ_REG|read_addr);
  v2 = ecat_spi.write(0x00);
  v3 = ecat_spi.write(0x00);
  // Chip must be deselected
  ecat_cs = 1;
  wait_us(2000);                      //sleep for 2 ms;

  return (v2<<8)+v3;
}

EsmacatShield::~EsmacatShield(void) 
{
  //empty block
}