This is a work in progress for an NRF2401P
Dependents: NRF_receiver sender locker4 Weather_Station_Ofiicial ... more
About
This is a simple library to drive the nRF24l01+.
Hardware
This uses the commonly available breakout. The connections are shown below
Software
Use case: For a simple transmitter
tx code snipet
#include "NRF2401P.h" int main() { * * long long addr1=0xAB00CD; // setup address - any 5 byte number - same as RX * int channel =0x12; // [0-126] setup channel, must be same as RX * bool txOK; * char msg[32]; * char ackData[32]; * char len; * * // Setup * NRF2401P nrf1(PTD6,PTD7, PTD5,PTD4, PTC12); //mosi, miso, sclk, csn, ce) * nrf1.quickTxSetup(channel, addr1); // sets nrf24l01+ as transmitter * * // transmit * strcpy (msg, "Hello"); * txOK= nrf1.transmitData(msg,strlen(msg)); * * // read ack data if available * if (nrf1.isAckData()) { * len= nrf1.getRxData(ackData); // len is number of bytes in ackData * } *}
Use case: For a simple receiver
rx code snipet
#include "NRF2401P.h" *int main(){ * * long long addr1=0xAB00CD; // setup address - any 5 byte number - same as TX * int channel =0x12; // [0-126] setup channel, must be same as TX * bool txOK; * char msg[32]; * char ackData[32]; * char len; * * // Setup * NRF2401P nrf1(PTD6,PTD7, PTD5,PTD4, PTC12); //mosi, miso, sclk, csn, ce) * nrf1.quickRxSetup(channel, addr1); // sets nrf24l01+ as receiver, using pipe 1 * * // set ack data * sprintf(ackData,"Ack data"); * nrf1.acknowledgeData(ackData, strlen(ackData),1); // ack for pipe 1 * * // receive * while (! nrf1.isRxData()); // note this blocks until RX data * len= nrf1.getRxData(msg); // gets the message, len is length of msg * *}
NRF2401P.h
- Committer:
- epgmdm
- Date:
- 2016-02-08
- Revision:
- 18:220df99d2d41
- Parent:
- 17:b132fc1a27d2
- Child:
- 20:e61edde5680d
File content as of revision 18:220df99d2d41:
/** *@section DESCRIPTION * mbed NRF2401+ Library *@section LICENSE * Copyright (c) 2015, Malcolm McCulloch * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal * in the Software without restriction, including without limitation the rights * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell * copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in * all copies or substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN * THE SOFTWARE. * @file "NRF2401P.h" */ #ifndef MBED_NRF2401P_H #define MBED_NRF2401P_H /** \brief A library to drive the nRF24l01+ * * This library is a simple way to get the nRF24l01+ up and running. * *- Use case: For a simple transmitter *@code *int main() { * * long long addr1=0xAB00CD; // setup address - any 5 byte number - same as RX * int channel =0x12; // [0-126] setup channel, must be same as RX * bool txOK; * char msg[32]; * char ackData[32]; * char len; * * // Setup * NRF2401P nrf1(PTD6,PTD7, PTD5,PTD4, PTC12); //mosi, miso, sclk, csn, ce) * nrf1.quickTxSetup(channel, addr1); // sets nrf24l01+ as transmitter * * // transmit * strcpy (msg, "Hello"); * txOK= nrf1.transmitData(msg,strlen(msg)); * * // read ack data if available * if (nrf1.isAckData()) { * len= nrf1.getRxData(ackData); // len is number of bytes in ackData * } *} *@endcode *- Use case: For a simple receiver *@code *int main(){ * * long long addr1=0xAB00CD; // setup address - any 5 byte number - same as TX * int channel =0x12; // [0-126] setup channel, must be same as TX * bool txOK; * char msg[32]; * char ackData[32]; * char len; * * // Setup * NRF2401P nrf1(PTD6,PTD7, PTD5,PTD4, PTC12); //mosi, miso, sclk, csn, ce) * nrf1.quickRxSetup(channel, addr1); // sets nrf24l01+ as receiver, using pipe 1 * * // set ack data * sprintf(ackData,"Ack data"); * nrf1.acknowledgeData(ackData, strlen(ackData),1); // ack for pipe 1 * * // receive * while (! nrf1.isRxData()); // note this blocks until RX data * len= nrf1.getRxData(msg); // gets the message, len is length of msg * *} *@endcode */ class NRF2401P { public: SPI *spi; DigitalOut csn,ce; char addressWidth; char logMsg[80]; char status; char statusS[32]; char pipe0Add[5]; char txAdd[5]; bool dynamic,debug; Serial *pc; /** Create a radio device for communicating with the RF24L01P via SPI. * * @param mosi The SPI slave data input pin. * @param miso The SPI Slave Data Output (with tri-state option). * @param sclk The SPI clock pin. * @param _csn The SPI chip select pin. * @param _ce Chip Enable pin (Activates RX or TX mode). */ NRF2401P (PinName mosi, PinName miso, PinName sclk, PinName _csn, PinName _ce); char acknowledgeData(char *data, char width, char pipe); char checkStatus(); void clearStatus(); void flushRx(); void flushTx(); char getRxData(char * buffer); /** Get the payload width for the next FIFO item (can be dynamic or static payload width) * * @returns * width of next available payload. */ char getRxWidth(); bool isAckData(); bool isRxData(); /** Is the Received Power Detector (ala carrier detect) register set high? * * @returns * true on received power levels above -64 dBm present in the RF channel. * false received power is less than -64 dBm (could indicate interference, etc). */ bool isRPDset(); /** Writes message and waits for 10 ms ( * * @param msg */ void log (char *msg); void quickRxSetup(int channel,long long addr); void quickTxSetup(int channel,long long addr); void readReg(char address, char *data); void readReg(char address, char *data, char width); char testReceive(); char testTransmit(); char transmitData( char *data, char width ); char retransmitData( ); char setAddressWidth(char width); /** Sets the frequency channel nRF24L01+ operates on * * @param chan F0 = 2400 + chan [MHz] * @returns * 0 on success, * non-zero on failure. */ char setChannel(char chan); void setDynamicPayload(); char setPwrUp(); char setPwrDown(); /** Set RF data rate and RF output power in TX mode * * @param speed RF data rate: '0x00' – 1Mbps, '0x01' – 2Mbps, '0x02' – 250kbps, '0x03' – Reserved * @param power RF output power: '0x00' – -18dBm, '0x01' – -12dBm, '0x02' – -6dBm, '0x03' – 0dBm * @returns * 0 on success, * non-zero on failure. */ char setRadio(char speed, char power); char setRxAddress(char *address, char pipe); char setRxAddress(long long address, char pipe); char setRxMode(); char setTxAddress(char *address); char setTxAddress(long long address); char setTxMode(); /** Sets the timing and number of TX retries * * @param delay Auto Retransmit Delay: '0000' – Wait 250uS', '0001' – Wait 500uS, ..., '1111' – Wait 4000uS * @param numTries Auto Retransmit Count: '0000' – Re-Transmit disabled, '0001' – Up to 1 Re-Transmit on fail of AA, ..., '1111' – Up to 15 Re-Transmit on fail of AA * @returns * 0 on success, * non-zero on failure. */ char setTxRetry(char delay, char numTries); void start(); char* statusString(); /** Print out 1 byte content of register * * @param name Name of register to print. * @param address Register address of interest. * @param newline By default print a trailing newline, can disable by setting false. */ void printReg(char* name, char address, bool newline=true); /** Print out 'width' bytes content of register * * @param name Name of register to print. * @param address Register address of interest. * @param width Number of bytes to print. * @param newline By default print a trailing newline, can disable by setting false. */ void printReg(char* name, char address, char width, bool newline=true); /** Print out 'width' bytes content of register * * @param name Name of register to print. * @param address Register address of interest. * @param width Number of bytes to print. * @param newline By default print a trailing newline, can disable by setting false. */ void printRegR(char* name, char address, char width, bool newline=true); /** Print verbose details about the radio setup and configuration * */ void printDetails(); void writeReg(char address, char *data, char width); void writeReg(char address, char data); void scratch(); }; #endif