wayne roberts / lorawan1v1

LoRaWAN end device MAC layer for SX1272 and SX1276. Supports LoRaWAN-1.0 and LoRaWAN-1.1

Dependencies:   sx12xx_hal

Dependents:   LoRaWAN-SanJose_Bootcamp LoRaWAN-grove-cayenne LoRaWAN-classC-demo LoRaWAN-grove-cayenne ... more

application project requirements

This library requires mbed TLS to be enabled.
The file mbed_app.json must be present in the project using this library:

{
    "macros": [ "MBEDTLS_CMAC_C" ]
}

regional PHY selection

All end device configuration is done in Commissioning.h, define desired radio frequency band of operation in this header file.
Commissioning.h is located in the application using this library.

end device provisioning

End device is provisioned by editing Commissioning.h in the application which is using this library
To use LoRaWAN-1.0 OTA: make sure LORAWAN_ROOT_APPKEY is undefined.
To use LoRaWAN-1.1 OTA, define LORAWAN_ROOT_APPKEY.
To select OTA operation, define LORAWAN_JOIN_EUI, then LORAWAN_DEVICE_EUI must be defined, along with root key(s).
To select ABP operation, undefine LORAWAN_JOIN_EUI: then define session keys

(note 1): LoRaWAN-1.0 OTA uses a single root key for both network server and application server.

In LoRaWAN-1.0 OTA: the single root AppKey is used to generate NwkSkey and AppSKey.
(note 2): In LoRaWAN-1.0 (both OTA and ABP) SNwkSIntKey, NwkSEncKey. FNwkSIntKey are of same value and are collectively known as NwkSKey.
(note 3): LoRaWAN-1.0 uses single network session key, LoRaWAN-1.1 uses 3 network session keys. Both use a unique application session key.

In LoRaWAN-1.1 OTA: the root NwkKey is used to generate SNwkSIntKey, NwkSEncKey, FNwkSIntKey
In LoRaWAN-1.1 OTA: the root AppKey is used to generate AppSKey

in ABP mode, the DevAddr, and session keys are fixed (never change), and frame counters never reset to zero.
ABP operation has no concept of: root keys, or DevEUI or JoinEUI/AppEUI.
in OTA mode, the DevAddr and session keys are assigned at join procedure, and frame counters reset at join.

eeprom

This library includes eeprom driver to support non-volatile storage required by LoRaWAN specification.
Currently eeprom is implemented for STM32L1 family and STM32L0 family.
Writing of values are wear-leveled to increase endurance; each write operation circulates across several memory locations. A read operation returns the highest value found. This simple method is used for sequence numbers which only increase.

AFCntDown is only used in LoRaWAN-1.1 when application payload is present in downlink and FPort > 0.
NFCntDown is used in LoRaWAN-1.1 when FPort is zero in downlink or application payload not present.
NFCntDown is the only downlink frame counter used in LoRaWAN-1.0
(note 1) OTA DevNonce is random number in LoRaWAN-1.0, therefore not stored in eeprom. DevNonce in LoRaWAN-1.1 is forever increasing (non-volatile) number upon each join request,.
RJcount0 is only stored in RAM because the value resets upon new session from JoinAccept, therefore not stored in eeprom.
Frame counters in OTA mode reset upon new session in join request, therefore are stored in RAM instead of eeprom for OTA.

radio driver support

When SX127x driver is used, both SX1272 and SX1276 are supported without defining at compile time. The chip is detected at start-up.
Supported radio platforms:

• SX1276 shield (nucleo boards)
• SX1272 shield (nucleo boards)
• North America Mote
• Murata discovery

Alternately, when SX126x driver is imported, the SX126xDVK1xAS board is used.

low-speed clock oscillator selection

LoRaWAN uses 32768Hz crystal to permit low-power operation.
However, some mbed targets might revert to low-speed internal oscillator, which is not accurate enough for LoRaWAN operation.
An oscillator check is performed at initialization; program will not start if internal oscillator is used.
To force LSE watch crystal, add to mbed_app.json

{
    "macros": [ "MBEDTLS_CMAC_C" ],
    "target_overrides": {
        "<your-target>": {
            "target.lse_available": true
        }
    }
}

add LSE check