Diff: Inits/UC1608.cpp

Revision:

0:75ec1b3cde17

Child:

1:ff019d22b275

diff -r 000000000000 -r 75ec1b3cde17 Inits/UC1608.cpp
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/Inits/UC1608.cpp	Thu Feb 12 22:22:47 2015 +0000
@@ -0,0 +1,95 @@
+#include "Protocols.h"
+#include "UC1608.h"
+
+//////////////////////////////////////////////////////////////////////////////////
+// display settings ///////////////////////////////////////////////////////
+/////////////////////////////////////////////////////////////////////////
+#define IC_X_SEGS    240 // UC1608 SEG has range 0-239 (239-0 if MX=1), check your datasheet, important for the orientation
+#define IC_Y_COMS    128  // UC1608 COM has range 0-127 (127-0 if MY=1), check your datasheet, important for the orientation
+#define LCDSIZE_X       240 // display X pixels
+#define LCDSIZE_Y       120  // display Y pixels, UC1608 is advertised as 240x128 but display size could be smaller
+
+
+
+UC1608::UC1608(proto_t displayproto, PortName port, PinName CS, PinName reset, PinName DC, PinName WR, PinName RD, const char *name)
+    : LCD(displayproto, port, CS, reset, DC, WR, RD, LCDSIZE_X, LCDSIZE_Y, IC_X_SEGS, IC_Y_COMS, name)
+{
+    hw_reset();
+    BusEnable(true);
+    init();
+    cls();
+    set_orientation(1);
+    locate(0,0);
+}
+UC1608::UC1608(proto_t displayproto, PinName mosi, PinName miso, PinName sclk, PinName CS, PinName reset, PinName DC, const char *name)
+    : LCD(displayproto, mosi, miso, sclk, CS, reset, DC, LCDSIZE_X, LCDSIZE_Y, IC_X_SEGS, IC_Y_COMS, name)
+{
+    hw_reset();
+    BusEnable(true);
+    init();
+    cls();
+    set_orientation(1);
+    locate(0,0);
+}
+// reset and init the lcd controller
+void UC1608::init()
+{
+    /* Start Initial Sequence ----------------------------------------------------*/
+    
+  //  wr_cmd(0xE2);   //  sw reset
+    wait_ms(15);
+    
+    wr_cmd(0x27);   // Multiplex rate :128   set temperature consenpation 0%
+    wr_cmd(0xEA);   //set bias:1/12bias
+
+    wr_cmd(0xC4);   // set mirror MX=1,MY=0 (controller->display SEGs wiring inverted)
+   // wr_cmd(0xA0);   // ADC select seg0-seg223
+    //wr_cmd(0xA1);   // ADC select seg223-seg0
+   // wr_cmd(0xC8);   // SHL select com63-com0
+    //wr_cmd(0xC0);   // SHL select com0-com63
+
+    wr_cmd(0x2F);   //  //Power Control:internal, LCD capacitance 60nf-90nf
+    wait_ms(10);
+    
+   // wr_cmd(0x81);//Set Gain and Potentiometer
+  //  wr_cmd(0x40|46);//Set Gain and Potentiometer  xx xxxxxx
+    set_contrast(46);
+    
+    wr_cmd(0x88);   //disable colum/page address wraparound
+    wr_cmd(0xA4);   //  LCD display ram (EntireDisplayOn disable)
+    wr_cmd(0x40);   // start line = 0
+    wr_cmd(0xA6);     // display normal (1 = illuminated)
+    wr_cmd(0xAF);     // display ON 
+
+}
+////////////////////////////////////////////////////////////////////
+// functions that overrides the standard ones implemented in LCD.cpp
+////////////////////////////////////////////////////////////////////
+void UC1608::mirrorXY(mirror_t mode)
+{
+    switch (mode)
+    {
+        case(NONE):
+            wr_cmd(0xC4); // this is in real X mirror command, but my display have SEGs wired inverted, so assume this is the default no-x-mirror
+            break;
+        case(X):
+            wr_cmd(0xC0);
+            break;
+        case(Y):
+            wr_cmd(0xCC);
+            break;
+        case(XY):
+            wr_cmd(0xC8);
+            break;
+    }
+}
+void UC1608::set_contrast(int o)
+{
+    contrast = o;
+    wr_cmd(0x81);      //  set volume
+    wr_cmd(0x40|(o&0x3F));
+}
+void UC1608::BusEnable(bool enable)
+{
+    LCD::BusEnable(!enable); // crap IC has CS not inverted (active HIGH)
+}
\ No newline at end of file