Activity
Answer posted for Question:
i get 0degree out of my temp sensor - Do you have pull - up resistors on SDA & SCK ?? and are the …
ceri clatworthy
- 08 Mar 2013
ceri clatworthy
- 08 Mar 2013
Answer posted for Question:
Register a new mbed to an existing account - You will need to registor the new flavour MBED (3 & 1/2 so far) but …
ceri clatworthy
- 28 Feb 2013
ceri clatworthy
- 28 Feb 2013
Answer posted for Question:
sending commands via usb to mbed to control PWM or analog out - The simpelest is .. <> PwmOut myled(LED1); PwmOut myled2(LED2); serial pc (USBTX,USBRX); int main() { …
ceri clatworthy
- 28 Feb 2013
ceri clatworthy
- 28 Feb 2013
Answer posted for Question:
Minimum to get LPC1768 up and running - but 12MHz Oscillator does not Oscillates? - have a look at some of my early posts, there are some photos of my …
ceri clatworthy
- 24 Feb 2013
ceri clatworthy
- 24 Feb 2013
Answer posted for Question:
mbed RTC crystal frequency 32kHz or 32.768kHz - the crystal frequency. is 32.768, although it is almost always documented as just 32kHz. but …
ceri clatworthy
- 24 Feb 2013
ceri clatworthy
- 24 Feb 2013
Answer posted for Question:
Custom NXP1768 hardware - you will need bin2hex, flash. magic. and a 3V3 serial lead, either FTDI, or. another …
ceri clatworthy
- 18 Feb 2013
ceri clatworthy
- 18 Feb 2013
Answer posted for Question:
Move mbed to my own hardware, possible? - If you use the LPC11U24, Then you can envoke the USB Bootloader, Which you save …
ceri clatworthy
- 07 Feb 2013
ceri clatworthy
- 07 Feb 2013
Reply to
Power LED won't stop blinking - Can't reformart or do anything
- I have experienced this as well, usually after HID code that sends out too many …
ceri clatworthy
- 30 Jan 2013
ceri clatworthy
- 30 Jan 2013
Question asked:
has anyone got USB Serial Host working? : Can anyone help, I need to make my MBED a USB Serial Host, and connect …
ceri clatworthy
- 20 Jan 2013
ceri clatworthy
- 20 Jan 2013
Reply to
Programming the lpc11u24 directly (no mbed)
- Very simple setup, LPC11U24, few Resistors,capacitors, FTE, and 12Mhz Crystal, and a USB Connector (could …
ceri clatworthy
- 21 Dec 2012
ceri clatworthy
- 21 Dec 2012
Reply to
Bare metal LPC11U24
- it is possible to program without crystal, if you use serial. I have posted some …
ceri clatworthy
- 18 Dec 2012
ceri clatworthy
- 18 Dec 2012
Answer posted for Question:
workshop development board question - The workshop board works pefectl with LPC11U24, Obviously, no ethernet :) **Ceri
ceri clatworthy
- 05 Dec 2012
ceri clatworthy
- 05 Dec 2012
Reply to
Teraterm values flickering and difficult to read.
- Re. weird. stuff, both P.C. and MBED must be set to SAME baud rate. as …
ceri clatworthy
- 05 Dec 2012
ceri clatworthy
- 05 Dec 2012
Reply to
Bricked M0
- Just found it, Thanks, I now have 2 UNBRICKED - M0's Pheww !!!!!!!!!!!!!!!!!!!!!!!!! Cheers Ceri
ceri clatworthy
- 03 Dec 2012
ceri clatworthy
- 03 Dec 2012
New topic
Bricked M0
- Help, I have just 'BRICKED' my second M0 MBED, I belive, what I have done …
ceri clatworthy
- 03 Dec 2012
ceri clatworthy
- 03 Dec 2012
Reply to
Pin19 analogIn consistently noisier than p20/p18 analogin pins
- After looking at your code .. #include "mbed.h" DigitalOut myled(LED1); //analog inputs AnalogIn ain_v1(p19); AnalogIn …
ceri clatworthy
- 21 Nov 2012
ceri clatworthy
- 21 Nov 2012
Reply to
Programming the lpc11u24 directly (no mbed)
- Does your PCB have USB working, such as Mouse or HID Device ? If so …
ceri clatworthy
- 19 Nov 2012
ceri clatworthy
- 19 Nov 2012
Answer posted for Question:
how do I make printf use my putc routine ? - if you look through some of the examples in the cookbook and the forums. there …
ceri clatworthy
- 18 Nov 2012
ceri clatworthy
- 18 Nov 2012