File content as of revision 0:26da608265f8:

#include "mbed.h"
#include "mbed_i2c.h"
#include "inv_mpu.h"
#include "inv_mpu_dmp_motion_driver.h"

#include "BLEDevice.h"
#include "DFUService.h"
#include "UARTService.h"


#define LOG(...)    { pc.printf(__VA_ARGS__); }

#define LED_GREEN   p21
#define LED_RED     p22
#define LED_BLUE    p23
#define BUTTON_PIN  p17
#define BATTERY_PIN p1

#define MPU6050_SDA p12
#define MPU6050_SCL p13

#define UART_TX     p9
#define UART_RX     p11
#define UART_CTS    p8
#define UART_RTS    p10

/* Starting sampling rate. */
#define DEFAULT_MPU_HZ  (100)

DigitalOut blue(LED_BLUE);
DigitalOut green(LED_GREEN);
DigitalOut red(LED_RED);

InterruptIn button(BUTTON_PIN);
AnalogIn    battery(BATTERY_PIN);
Serial pc(UART_TX, UART_RX);

InterruptIn motion_probe(p14);

BLEDevice  ble;
UARTService *uartServicePtr;

volatile bool bleIsConnected = false;
volatile uint8_t tick_event = 0;
volatile uint8_t motion_event = 0;
static signed char board_orientation[9] = {
    1, 0, 0,
    0, 1, 0,
    0, 0, 1
};


void check_i2c_bus(void);
unsigned short inv_orientation_matrix_to_scalar( const signed char *mtx);

void connectionCallback(Gap::Handle_t handle, Gap::addr_type_t peerAddrType, const Gap::address_t peerAddr, const Gap::ConnectionParams_t *params)
{
    LOG("Connected!\n");
    bleIsConnected = true;
}

void disconnectionCallback(Gap::Handle_t handle, Gap::DisconnectionReason_t reason)
{
    LOG("Disconnected!\n");
    LOG("Restarting the advertising process\n");
    ble.startAdvertising();
    bleIsConnected = false;
}

void tick(void)
{
    green = !green;
}

void detect(void)
{
    LOG("Button pressed\n");
    
    blue = !blue;
}

void motion_interrupt_handle(void)
{
    motion_event = 1;
}

void tap_cb(unsigned char direction, unsigned char count)
{
    LOG("Tap motion detected\n");
}

void android_orient_cb(unsigned char orientation)
{
    LOG("Oriention changed\n");
}


int main(void)
{
    blue  = 1;
    green = 1;
    red   = 1;

    pc.baud(115200);
    LOG("---- Seeed Tiny BLE ----\n");
    
    Ticker ticker;
    ticker.attach(tick, 3);

    button.fall(detect);

    LOG("Initialising the nRF51822\n");
    ble.init();
    ble.onDisconnection(disconnectionCallback);
    ble.onConnection(connectionCallback);


    /* setup advertising */
    ble.accumulateAdvertisingPayload(GapAdvertisingData::BREDR_NOT_SUPPORTED);
    ble.setAdvertisingType(GapAdvertisingParams::ADV_CONNECTABLE_UNDIRECTED);
    ble.accumulateAdvertisingPayload(GapAdvertisingData::SHORTENED_LOCAL_NAME,
                                     (const uint8_t *)"smurfs", sizeof("smurfs"));
    ble.accumulateAdvertisingPayload(GapAdvertisingData::COMPLETE_LIST_128BIT_SERVICE_IDS,
                                     (const uint8_t *)UARTServiceUUID_reversed, sizeof(UARTServiceUUID_reversed));
    DFUService dfu(ble);                                 
    UARTService uartService(ble);
    uartServicePtr = &uartService;
    //uartService.retargetStdout();

    ble.setAdvertisingInterval(160); /* 100ms; in multiples of 0.625ms. */
    ble.startAdvertising();
    
    check_i2c_bus();
   
    mbed_i2c_init(MPU6050_SDA, MPU6050_SCL);
    motion_probe.fall(motion_interrupt_handle);
    

    if (mpu_init(0)) {
//         LOG("failed to initialize mpu6050\r\n");
    }
    
    /* Get/set hardware configuration. Start gyro. */
    /* Wake up all sensors. */
    mpu_set_sensors(INV_XYZ_GYRO | INV_XYZ_ACCEL);
    /* Push both gyro and accel data into the FIFO. */
    mpu_configure_fifo(INV_XYZ_GYRO | INV_XYZ_ACCEL);
    mpu_set_sample_rate(DEFAULT_MPU_HZ);
    
    /* Read back configuration in case it was set improperly. */
    unsigned char accel_fsr;
    unsigned short gyro_rate, gyro_fsr;
    mpu_get_sample_rate(&gyro_rate);
    mpu_get_gyro_fsr(&gyro_fsr);
    mpu_get_accel_fsr(&accel_fsr);
    
    dmp_load_motion_driver_firmware();
    dmp_set_orientation(
        inv_orientation_matrix_to_scalar(board_orientation));
    dmp_register_tap_cb(tap_cb);
    dmp_register_android_orient_cb(android_orient_cb);
    
    uint16_t dmp_features = DMP_FEATURE_6X_LP_QUAT | DMP_FEATURE_TAP |
                       DMP_FEATURE_ANDROID_ORIENT | DMP_FEATURE_SEND_RAW_ACCEL | DMP_FEATURE_SEND_CAL_GYRO |
                       DMP_FEATURE_GYRO_CAL;
    dmp_enable_feature(dmp_features);
    dmp_set_fifo_rate(DEFAULT_MPU_HZ);
    mpu_set_dmp_state(1);
    
//     dmp_set_interrupt_mode(DMP_INT_GESTURE);
    dmp_set_tap_thresh(TAP_XYZ, 50);

    while (true) {
        if (motion_event) {
            motion_event = 0;
            
            unsigned long sensor_timestamp;
            short gyro[3], accel[3], sensors;
            long quat[4];
            unsigned char more = 1;
            
            while (more) {
                /* This function gets new data from the FIFO when the DMP is in
                 * use. The FIFO can contain any combination of gyro, accel,
                 * quaternion, and gesture data. The sensors parameter tells the
                 * caller which data fields were actually populated with new data.
                 * For example, if sensors == (INV_XYZ_GYRO | INV_WXYZ_QUAT), then
                 * the FIFO isn't being filled with accel data.
                 * The driver parses the gesture data to determine if a gesture
                 * event has occurred; on an event, the application will be notified
                 * via a callback (assuming that a callback function was properly
                 * registered). The more parameter is non-zero if there are
                 * leftover packets in the FIFO.
                 */
                dmp_read_fifo(gyro, accel, quat, &sensor_timestamp, &sensors,
                              &more);
                /* Gyro and accel data are written to the FIFO by the DMP in chip
                 * frame and hardware units. This behavior is convenient because it
                 * keeps the gyro and accel outputs of dmp_read_fifo and
                 * mpu_read_fifo consistent.
                 */
                if (sensors & INV_XYZ_GYRO) {
                    // LOG("GYRO: %d, %d, %d\n", gyro[0], gyro[1], gyro[2]);
                }
                if (sensors & INV_XYZ_ACCEL) {
                    // LOG("ACC: %d, %d, %d\n", accel[0], accel[1], accel[2]);
                }
                
                /* Unlike gyro and accel, quaternions are written to the FIFO in
                 * the body frame, q30. The orientation is set by the scalar passed
                 * to dmp_set_orientation during initialization.
                 */
                if (sensors & INV_WXYZ_QUAT) {
                    // LOG("QUAT: %ld, %ld, %ld, %ld\n", quat[0], quat[1], quat[2], quat[3]);
                }
            }
        } else {
            ble.waitForEvent();
        }
    }
}

void check_i2c_bus(void)
{
    
    DigitalInOut scl(MPU6050_SCL);
    DigitalInOut sda(MPU6050_SDA);
    
    scl.input();
    sda.input();
    int scl_level = scl;
    int sda_level = sda;
    if (scl_level == 0 || sda_level == 0) {
        printf("scl: %d, sda: %d, i2c bus is not released\r\n", scl_level, sda_level);
        
        scl.output();
        for (int i = 0; i < 8; i++) {
            scl = 0;
            wait_us(10);
            scl = 1;
            wait_us(10);
        }
    }
    
    scl.input();
    
    scl_level = scl;
    sda_level = sda;
    if (scl_level == 0 || sda_level == 0) {
        printf("scl: %d, sda: %d, i2c bus is still not released\r\n", scl_level, sda_level);
    }
}

/* These next two functions converts the orientation matrix (see
 * gyro_orientation) to a scalar representation for use by the DMP.
 * NOTE: These functions are borrowed from Invensense's MPL.
 */
static inline unsigned short inv_row_2_scale(const signed char *row)
{
    unsigned short b;

    if (row[0] > 0)
        b = 0;
    else if (row[0] < 0)
        b = 4;
    else if (row[1] > 0)
        b = 1;
    else if (row[1] < 0)
        b = 5;
    else if (row[2] > 0)
        b = 2;
    else if (row[2] < 0)
        b = 6;
    else
        b = 7;      // error
    return b;
}

unsigned short inv_orientation_matrix_to_scalar(
    const signed char *mtx)
{
    unsigned short scalar;

    /*
       XYZ  010_001_000 Identity Matrix
       XZY  001_010_000
       YXZ  010_000_001
       YZX  000_010_001
       ZXY  001_000_010
       ZYX  000_001_010
     */

    scalar = inv_row_2_scale(mtx);
    scalar |= inv_row_2_scale(mtx + 3) << 3;
    scalar |= inv_row_2_scale(mtx + 6) << 6;


    return scalar;
}