File content as of revision 59:568e7be5232f:

#include "mbed.h"
#include "DRV.h"
#include "macro.h"
DRV832x::DRV832x(SPI *spi, DigitalOut *cs){
    _spi = spi;
    _cs = cs;
    _cs->write(1);
    wait_us(10);
    _spi->format(16, 1);
    _spi->frequency(500000);
    }
    
uint16_t DRV832x::spi_write(uint16_t val)
{
    _cs->write(0);
    wait_us(10);
    uint16_t reply = _spi->write(val);
    _cs->write(1);
    return reply;
    }
    
int DRV832x::read_FSR1(void)
{
    uint16_t val = (1<<15) | FSR1;
    return spi_write(val); 
    }
    
int DRV832x::read_FSR2(void)
{
    uint16_t val = (1<<15) | FSR2;
    return spi_write(val);
    }
    
int DRV832x::read_register(int reg)
{
    return spi_write((1<<15) | (reg<<11));
    }
    
void DRV832x::write_register(int reg, int val)
{
    spi_write((reg<<11) | val);
    }
void DRV832x::write_DCR(int DIS_CPUV, int DIS_GDF, int OTW_REP, int PWM_MODE, int PWM_COM, int PWM_DIR, int COAST, int BRAKE, int CLR_FLT)
{
    uint16_t val = (DCR<<11) | (DIS_CPUV<<9) | (DIS_GDF<<8) | (OTW_REP<<7) | (PWM_MODE<<5) | (PWM_COM<<4) | (PWM_DIR<<3) | (COAST<<2) | (BRAKE<<1) | CLR_FLT;
    spi_write(val);
    }
void DRV832x::write_HSR(int LOCK, int IDRIVEP_HS, int IDRIVEN_HS)
{
    uint16_t val = (HSR<<11) | (LOCK<<8) | (IDRIVEP_HS<<4) | IDRIVEN_HS;
    spi_write(val);
    }
void DRV832x::write_LSR(int CBC, int TDRIVE, int IDRIVEP_LS, int IDRIVEN_LS)
{
    uint16_t val = (LSR<<11) | (CBC<<10) | (TDRIVE<<8) | (IDRIVEP_LS<<4) | IDRIVEN_LS;
    spi_write(val);
    }
void DRV832x::write_OCPCR(int TRETRY, int DEAD_TIME, int OCP_MODE, int OCP_DEG, int VDS_LVL)
{
    uint16_t val = (OCPCR<<11) | (TRETRY<<10) | (DEAD_TIME<<8) | (OCP_MODE<<6) | (OCP_DEG<<4) | VDS_LVL;
    spi_write(val);
    }
void DRV832x::write_CSACR(int CSA_FET, int VREF_DIV, int LS_REF, int CSA_GAIN, int DIS_SEN, int CSA_CAL_A, int CSA_CAL_B, int CSA_CAL_C, int SEN_LVL)
{
    uint16_t val = (CSACR<<11) | (CSA_FET<<10) | (VREF_DIV<<9) | (LS_REF<<8) | (CSA_GAIN<<6) | (DIS_SEN<<5) | (CSA_CAL_A<<4) | (CSA_CAL_B<<3) | (CSA_CAL_C<<2) | SEN_LVL;
    spi_write(val);
        }
        
void DRV832x::print_faults(void)
{
    uint16_t val1 = read_FSR1();
    wait_us(10);
    uint16_t val2 = read_FSR2();
    wait_us(10);
    
    if(val1 & (1<<10)){Serial_printf("\n\rFAULT\n\r");}

    if(val1 & (1<<9)){Serial_printf("VDS_OCP\n\r");} // VDS monitor overcurrent fault condition
    if(val1 & (1<<8)){Serial_printf("GDF\n\r");}  // Indicates gate drive fault condition
    if(val1 & (1<<7)){Serial_printf("UVLO\n\r");} // undervoltage lockout fault condition
    if(val1 & (1<<6)){Serial_printf("OTSD\n\r");} // overtemperature shutdown
    if(val1 & (1<<5)){Serial_printf("VDS_HA\n\r");} // VDS overcurrent fault on the A high-side MOSFET
    if(val1 & (1<<4)){Serial_printf("VDS_LA\n\r");}  // s VDS overcurrent fault on the A low-side MOSFET
    if(val1 & (1<<3)){Serial_printf("VDS_HB\n\r");}  // VDS overcurrent fault on the B high-side MOSFET
    if(val1 & (1<<2)){Serial_printf("VDS_LB\n\r");}  // VDS overcurrent fault on the B low-side MOSFET
    if(val1 & (1<<1)){Serial_printf("VDS_HC\n\r");}  // VDS overcurrent fault on the C high-side MOSFET
    if(val1 & (1)){Serial_printf("VDS_LC\n\r");}     // VDS overcurrent fault on the C low-side MOSFET
    
    if(val2 & (1<<10)){Serial_printf("SA_OC\n\r");}  // overcurrent on phase A sense amplifier (DRV8323xS)
    if(val2 & (1<<9)){Serial_printf("SB_OC\n\r");}  // overcurrent on phase B sense amplifier
    if(val2 & (1<<8)){Serial_printf("SC_OC\n\r");}  // overcurrent on phase C sense amplifier
    if(val2 & (1<<7)){Serial_printf("OTW\n\r");}   // overtemperature warning
    if(val2 & (1<<6)){Serial_printf("CPUV\n\r");}  // charge pump undervoltage fault condition
    if(val2 & (1<<5)){Serial_printf("VGS_HA\n\r");}
    if(val2 & (1<<4)){Serial_printf("VGS_LA\n\r");}
    if(val2 & (1<<3)){Serial_printf("VGS_HB\n\r");}
    if(val2 & (1<<2)){Serial_printf("VGS_LB\n\r");}
    if(val2 & (1<<1)){Serial_printf("VGS_HC\n\r");}
    if(val2 & (1)){Serial_printf("VGS_LC\n\r");}
    }
    
void DRV832x::enable_gd(void)
{
    uint16_t val = (read_register(DCR)) & (~(0x1<<2));
    write_register(DCR, val);
    }
    
void DRV832x::disable_gd(void)
{
    uint16_t val = (read_register(DCR)) | (0x1<<2);    
    write_register(DCR, val);
    }
    
void DRV832x::calibrate(void)
{
    uint16_t val = 0x1<<4 + 0x1<<3 + 0x1<<2;
    write_register(CSACR, val);
    }