Nordic stack and drivers for the mbed BLE API
Fork of nRF51822 by
Diff: TARGET_MCU_NRF51822/sdk/source/device/nrf51.h
- Revision:
- 638:c90ae1400bf2
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/TARGET_MCU_NRF51822/sdk/source/device/nrf51.h Wed Sep 14 14:39:43 2016 +0100 @@ -0,0 +1,1263 @@ +/* + * Copyright (c) Nordic Semiconductor ASA + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, this + * list of conditions and the following disclaimer. + * + * 2. Redistributions in binary form must reproduce the above copyright notice, this + * list of conditions and the following disclaimer in the documentation and/or + * other materials provided with the distribution. + * + * 3. Neither the name of Nordic Semiconductor ASA nor the names of other + * contributors to this software may be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR + * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ + +#ifndef NRF51_H +#define NRF51_H + +#ifdef __cplusplus +extern "C" { +#endif + + +/* ------------------------- Interrupt Number Definition ------------------------ */ + +typedef enum { +/* ------------------- Cortex-M0 Processor Exceptions Numbers ------------------- */ + Reset_IRQn = -15, /*!< 1 Reset Vector, invoked on Power up and warm reset */ + NonMaskableInt_IRQn = -14, /*!< 2 Non maskable Interrupt, cannot be stopped or preempted */ + HardFault_IRQn = -13, /*!< 3 Hard Fault, all classes of Fault */ + SVCall_IRQn = -5, /*!< 11 System Service Call via SVC instruction */ + DebugMonitor_IRQn = -4, /*!< 12 Debug Monitor */ + PendSV_IRQn = -2, /*!< 14 Pendable request for system service */ + SysTick_IRQn = -1, /*!< 15 System Tick Timer */ +/* ---------------------- nrf51 Specific Interrupt Numbers ---------------------- */ + POWER_CLOCK_IRQn = 0, /*!< 0 POWER_CLOCK */ + RADIO_IRQn = 1, /*!< 1 RADIO */ + UART0_IRQn = 2, /*!< 2 UART0 */ + SPI0_TWI0_IRQn = 3, /*!< 3 SPI0_TWI0 */ + SPI1_TWI1_IRQn = 4, /*!< 4 SPI1_TWI1 */ + GPIOTE_IRQn = 6, /*!< 6 GPIOTE */ + ADC_IRQn = 7, /*!< 7 ADC */ + TIMER0_IRQn = 8, /*!< 8 TIMER0 */ + TIMER1_IRQn = 9, /*!< 9 TIMER1 */ + TIMER2_IRQn = 10, /*!< 10 TIMER2 */ + RTC0_IRQn = 11, /*!< 11 RTC0 */ + TEMP_IRQn = 12, /*!< 12 TEMP */ + RNG_IRQn = 13, /*!< 13 RNG */ + ECB_IRQn = 14, /*!< 14 ECB */ + CCM_AAR_IRQn = 15, /*!< 15 CCM_AAR */ + WDT_IRQn = 16, /*!< 16 WDT */ + RTC1_IRQn = 17, /*!< 17 RTC1 */ + QDEC_IRQn = 18, /*!< 18 QDEC */ + LPCOMP_IRQn = 19, /*!< 19 LPCOMP */ + SWI0_IRQn = 20, /*!< 20 SWI0 */ + SWI1_IRQn = 21, /*!< 21 SWI1 */ + SWI2_IRQn = 22, /*!< 22 SWI2 */ + SWI3_IRQn = 23, /*!< 23 SWI3 */ + SWI4_IRQn = 24, /*!< 24 SWI4 */ + SWI5_IRQn = 25 /*!< 25 SWI5 */ +} IRQn_Type; + + +/** @addtogroup Configuration_of_CMSIS + * @{ + */ + + +/* ================================================================================ */ +/* ================ Processor and Core Peripheral Section ================ */ +/* ================================================================================ */ + +/* ----------------Configuration of the Cortex-M0 Processor and Core Peripherals---------------- */ +#define __CM0_REV 0x0301 /*!< Cortex-M0 Core Revision */ +#define __MPU_PRESENT 0 /*!< MPU present or not */ +#define __NVIC_PRIO_BITS 2 /*!< Number of Bits used for Priority Levels */ +#define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */ +/** @} */ /* End of group Configuration_of_CMSIS */ + +#include "core_cm0.h" /*!< Cortex-M0 processor and core peripherals */ +#include "system_nrf51.h" /*!< nrf51 System */ + + +/* ================================================================================ */ +/* ================ Device Specific Peripheral Section ================ */ +/* ================================================================================ */ + + +/** @addtogroup Device_Peripheral_Registers + * @{ + */ + + +/* ------------------- Start of section using anonymous unions ------------------ */ +#if defined(__CC_ARM) + #pragma push + #pragma anon_unions +#elif defined(__ICCARM__) + #pragma language=extended +#elif defined(__GNUC__) + /* anonymous unions are enabled by default */ +#elif defined(__TMS470__) +/* anonymous unions are enabled by default */ +#elif defined(__TASKING__) + #pragma warning 586 +#else + #warning Not supported compiler type +#endif + + +typedef struct { + __IO uint32_t CPU0; /*!< Configurable priority configuration register for CPU0. */ + __IO uint32_t SPIS1; /*!< Configurable priority configuration register for SPIS1. */ + __IO uint32_t RADIO; /*!< Configurable priority configuration register for RADIO. */ + __IO uint32_t ECB; /*!< Configurable priority configuration register for ECB. */ + __IO uint32_t CCM; /*!< Configurable priority configuration register for CCM. */ + __IO uint32_t AAR; /*!< Configurable priority configuration register for AAR. */ +} AMLI_RAMPRI_Type; + +typedef struct { + __IO uint32_t SCK; /*!< Pin select for SCK. */ + __IO uint32_t MOSI; /*!< Pin select for MOSI. */ + __IO uint32_t MISO; /*!< Pin select for MISO. */ +} SPIM_PSEL_Type; + +typedef struct { + __IO uint32_t PTR; /*!< Data pointer. */ + __IO uint32_t MAXCNT; /*!< Maximum number of buffer bytes to receive. */ + __I uint32_t AMOUNT; /*!< Number of bytes received in the last transaction. */ +} SPIM_RXD_Type; + +typedef struct { + __IO uint32_t PTR; /*!< Data pointer. */ + __IO uint32_t MAXCNT; /*!< Maximum number of buffer bytes to send. */ + __I uint32_t AMOUNT; /*!< Number of bytes sent in the last transaction. */ +} SPIM_TXD_Type; + +typedef struct { + __O uint32_t EN; /*!< Enable channel group. */ + __O uint32_t DIS; /*!< Disable channel group. */ +} PPI_TASKS_CHG_Type; + +typedef struct { + __IO uint32_t EEP; /*!< Channel event end-point. */ + __IO uint32_t TEP; /*!< Channel task end-point. */ +} PPI_CH_Type; + + +/* ================================================================================ */ +/* ================ POWER ================ */ +/* ================================================================================ */ + + +/** + * @brief Power Control. (POWER) + */ + +typedef struct { /*!< POWER Structure */ + __I uint32_t RESERVED0[30]; + __O uint32_t TASKS_CONSTLAT; /*!< Enable constant latency mode. */ + __O uint32_t TASKS_LOWPWR; /*!< Enable low power mode (variable latency). */ + __I uint32_t RESERVED1[34]; + __IO uint32_t EVENTS_POFWARN; /*!< Power failure warning. */ + __I uint32_t RESERVED2[126]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[61]; + __IO uint32_t RESETREAS; /*!< Reset reason. */ + __I uint32_t RESERVED4[9]; + __I uint32_t RAMSTATUS; /*!< Ram status register. */ + __I uint32_t RESERVED5[53]; + __O uint32_t SYSTEMOFF; /*!< System off register. */ + __I uint32_t RESERVED6[3]; + __IO uint32_t POFCON; /*!< Power failure configuration. */ + __I uint32_t RESERVED7[2]; + __IO uint32_t GPREGRET; /*!< General purpose retention register. This register is a retained + register. */ + __I uint32_t RESERVED8; + __IO uint32_t RAMON; /*!< Ram on/off. */ + __I uint32_t RESERVED9[7]; + __IO uint32_t RESET; /*!< Pin reset functionality configuration register. This register + is a retained register. */ + __I uint32_t RESERVED10[3]; + __IO uint32_t RAMONB; /*!< Ram on/off. */ + __I uint32_t RESERVED11[8]; + __IO uint32_t DCDCEN; /*!< DCDC converter enable configuration register. */ + __I uint32_t RESERVED12[291]; + __IO uint32_t DCDCFORCE; /*!< DCDC power-up force register. */ +} NRF_POWER_Type; + + +/* ================================================================================ */ +/* ================ CLOCK ================ */ +/* ================================================================================ */ + + +/** + * @brief Clock control. (CLOCK) + */ + +typedef struct { /*!< CLOCK Structure */ + __O uint32_t TASKS_HFCLKSTART; /*!< Start HFCLK clock source. */ + __O uint32_t TASKS_HFCLKSTOP; /*!< Stop HFCLK clock source. */ + __O uint32_t TASKS_LFCLKSTART; /*!< Start LFCLK clock source. */ + __O uint32_t TASKS_LFCLKSTOP; /*!< Stop LFCLK clock source. */ + __O uint32_t TASKS_CAL; /*!< Start calibration of LFCLK RC oscillator. */ + __O uint32_t TASKS_CTSTART; /*!< Start calibration timer. */ + __O uint32_t TASKS_CTSTOP; /*!< Stop calibration timer. */ + __I uint32_t RESERVED0[57]; + __IO uint32_t EVENTS_HFCLKSTARTED; /*!< HFCLK oscillator started. */ + __IO uint32_t EVENTS_LFCLKSTARTED; /*!< LFCLK oscillator started. */ + __I uint32_t RESERVED1; + __IO uint32_t EVENTS_DONE; /*!< Calibration of LFCLK RC oscillator completed. */ + __IO uint32_t EVENTS_CTTO; /*!< Calibration timer timeout. */ + __I uint32_t RESERVED2[124]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[63]; + __I uint32_t HFCLKRUN; /*!< Task HFCLKSTART trigger status. */ + __I uint32_t HFCLKSTAT; /*!< High frequency clock status. */ + __I uint32_t RESERVED4; + __I uint32_t LFCLKRUN; /*!< Task LFCLKSTART triggered status. */ + __I uint32_t LFCLKSTAT; /*!< Low frequency clock status. */ + __I uint32_t LFCLKSRCCOPY; /*!< Clock source for the LFCLK clock, set when task LKCLKSTART is + triggered. */ + __I uint32_t RESERVED5[62]; + __IO uint32_t LFCLKSRC; /*!< Clock source for the LFCLK clock. */ + __I uint32_t RESERVED6[7]; + __IO uint32_t CTIV; /*!< Calibration timer interval. */ + __I uint32_t RESERVED7[5]; + __IO uint32_t XTALFREQ; /*!< Crystal frequency. */ +} NRF_CLOCK_Type; + + +/* ================================================================================ */ +/* ================ MPU ================ */ +/* ================================================================================ */ + + +/** + * @brief Memory Protection Unit. (MPU) + */ + +typedef struct { /*!< MPU Structure */ + __I uint32_t RESERVED0[330]; + __IO uint32_t PERR0; /*!< Configuration of peripherals in mpu regions. */ + __IO uint32_t RLENR0; /*!< Length of RAM region 0. */ + __I uint32_t RESERVED1[52]; + __IO uint32_t PROTENSET0; /*!< Erase and write protection bit enable set register. */ + __IO uint32_t PROTENSET1; /*!< Erase and write protection bit enable set register. */ + __IO uint32_t DISABLEINDEBUG; /*!< Disable erase and write protection mechanism in debug mode. */ + __IO uint32_t PROTBLOCKSIZE; /*!< Erase and write protection block size. */ +} NRF_MPU_Type; + + +/* ================================================================================ */ +/* ================ AMLI ================ */ +/* ================================================================================ */ + + +/** + * @brief AHB Multi-Layer Interface. (AMLI) + */ + +typedef struct { /*!< AMLI Structure */ + __I uint32_t RESERVED0[896]; + AMLI_RAMPRI_Type RAMPRI; /*!< RAM configurable priority configuration structure. */ +} NRF_AMLI_Type; + + +/* ================================================================================ */ +/* ================ RADIO ================ */ +/* ================================================================================ */ + + +/** + * @brief The radio. (RADIO) + */ + +typedef struct { /*!< RADIO Structure */ + __O uint32_t TASKS_TXEN; /*!< Enable radio in TX mode. */ + __O uint32_t TASKS_RXEN; /*!< Enable radio in RX mode. */ + __O uint32_t TASKS_START; /*!< Start radio. */ + __O uint32_t TASKS_STOP; /*!< Stop radio. */ + __O uint32_t TASKS_DISABLE; /*!< Disable radio. */ + __O uint32_t TASKS_RSSISTART; /*!< Start the RSSI and take one sample of the receive signal strength. */ + __O uint32_t TASKS_RSSISTOP; /*!< Stop the RSSI measurement. */ + __O uint32_t TASKS_BCSTART; /*!< Start the bit counter. */ + __O uint32_t TASKS_BCSTOP; /*!< Stop the bit counter. */ + __I uint32_t RESERVED0[55]; + __IO uint32_t EVENTS_READY; /*!< Ready event. */ + __IO uint32_t EVENTS_ADDRESS; /*!< Address event. */ + __IO uint32_t EVENTS_PAYLOAD; /*!< Payload event. */ + __IO uint32_t EVENTS_END; /*!< End event. */ + __IO uint32_t EVENTS_DISABLED; /*!< Disable event. */ + __IO uint32_t EVENTS_DEVMATCH; /*!< A device address match occurred on the last received packet. */ + __IO uint32_t EVENTS_DEVMISS; /*!< No device address match occurred on the last received packet. */ + __IO uint32_t EVENTS_RSSIEND; /*!< Sampling of the receive signal strength complete. A new RSSI + sample is ready for readout at the RSSISAMPLE register. */ + __I uint32_t RESERVED1[2]; + __IO uint32_t EVENTS_BCMATCH; /*!< Bit counter reached bit count value specified in BCC register. */ + __I uint32_t RESERVED2[53]; + __IO uint32_t SHORTS; /*!< Shortcuts for the radio. */ + __I uint32_t RESERVED3[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED4[61]; + __I uint32_t CRCSTATUS; /*!< CRC status of received packet. */ + __I uint32_t RESERVED5; + __I uint32_t RXMATCH; /*!< Received address. */ + __I uint32_t RXCRC; /*!< Received CRC. */ + __I uint32_t DAI; /*!< Device address match index. */ + __I uint32_t RESERVED6[60]; + __IO uint32_t PACKETPTR; /*!< Packet pointer. Decision point: START task. */ + __IO uint32_t FREQUENCY; /*!< Frequency. */ + __IO uint32_t TXPOWER; /*!< Output power. */ + __IO uint32_t MODE; /*!< Data rate and modulation. */ + __IO uint32_t PCNF0; /*!< Packet configuration 0. */ + __IO uint32_t PCNF1; /*!< Packet configuration 1. */ + __IO uint32_t BASE0; /*!< Radio base address 0. Decision point: START task. */ + __IO uint32_t BASE1; /*!< Radio base address 1. Decision point: START task. */ + __IO uint32_t PREFIX0; /*!< Prefixes bytes for logical addresses 0 to 3. */ + __IO uint32_t PREFIX1; /*!< Prefixes bytes for logical addresses 4 to 7. */ + __IO uint32_t TXADDRESS; /*!< Transmit address select. */ + __IO uint32_t RXADDRESSES; /*!< Receive address select. */ + __IO uint32_t CRCCNF; /*!< CRC configuration. */ + __IO uint32_t CRCPOLY; /*!< CRC polynomial. */ + __IO uint32_t CRCINIT; /*!< CRC initial value. */ + __IO uint32_t TEST; /*!< Test features enable register. */ + __IO uint32_t TIFS; /*!< Inter Frame Spacing in microseconds. */ + __I uint32_t RSSISAMPLE; /*!< RSSI sample. */ + __I uint32_t RESERVED7; + __I uint32_t STATE; /*!< Current radio state. */ + __IO uint32_t DATAWHITEIV; /*!< Data whitening initial value. */ + __I uint32_t RESERVED8[2]; + __IO uint32_t BCC; /*!< Bit counter compare. */ + __I uint32_t RESERVED9[39]; + __IO uint32_t DAB[8]; /*!< Device address base segment. */ + __IO uint32_t DAP[8]; /*!< Device address prefix. */ + __IO uint32_t DACNF; /*!< Device address match configuration. */ + __I uint32_t RESERVED10[56]; + __IO uint32_t OVERRIDE0; /*!< Trim value override register 0. */ + __IO uint32_t OVERRIDE1; /*!< Trim value override register 1. */ + __IO uint32_t OVERRIDE2; /*!< Trim value override register 2. */ + __IO uint32_t OVERRIDE3; /*!< Trim value override register 3. */ + __IO uint32_t OVERRIDE4; /*!< Trim value override register 4. */ + __I uint32_t RESERVED11[561]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_RADIO_Type; + + +/* ================================================================================ */ +/* ================ UART ================ */ +/* ================================================================================ */ + + +/** + * @brief Universal Asynchronous Receiver/Transmitter. (UART) + */ + +typedef struct { /*!< UART Structure */ + __O uint32_t TASKS_STARTRX; /*!< Start UART receiver. */ + __O uint32_t TASKS_STOPRX; /*!< Stop UART receiver. */ + __O uint32_t TASKS_STARTTX; /*!< Start UART transmitter. */ + __O uint32_t TASKS_STOPTX; /*!< Stop UART transmitter. */ + __I uint32_t RESERVED0[3]; + __O uint32_t TASKS_SUSPEND; /*!< Suspend UART. */ + __I uint32_t RESERVED1[56]; + __IO uint32_t EVENTS_CTS; /*!< CTS activated. */ + __IO uint32_t EVENTS_NCTS; /*!< CTS deactivated. */ + __IO uint32_t EVENTS_RXDRDY; /*!< Data received in RXD. */ + __I uint32_t RESERVED2[4]; + __IO uint32_t EVENTS_TXDRDY; /*!< Data sent from TXD. */ + __I uint32_t RESERVED3; + __IO uint32_t EVENTS_ERROR; /*!< Error detected. */ + __I uint32_t RESERVED4[7]; + __IO uint32_t EVENTS_RXTO; /*!< Receiver timeout. */ + __I uint32_t RESERVED5[46]; + __IO uint32_t SHORTS; /*!< Shortcuts for UART. */ + __I uint32_t RESERVED6[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED7[93]; + __IO uint32_t ERRORSRC; /*!< Error source. Write error field to 1 to clear error. */ + __I uint32_t RESERVED8[31]; + __IO uint32_t ENABLE; /*!< Enable UART and acquire IOs. */ + __I uint32_t RESERVED9; + __IO uint32_t PSELRTS; /*!< Pin select for RTS. */ + __IO uint32_t PSELTXD; /*!< Pin select for TXD. */ + __IO uint32_t PSELCTS; /*!< Pin select for CTS. */ + __IO uint32_t PSELRXD; /*!< Pin select for RXD. */ + __I uint32_t RXD; /*!< RXD register. On read action the buffer pointer is displaced. + Once read the character is consumed. If read when no character + available, the UART will stop working. */ + __O uint32_t TXD; /*!< TXD register. */ + __I uint32_t RESERVED10; + __IO uint32_t BAUDRATE; /*!< UART Baudrate. */ + __I uint32_t RESERVED11[17]; + __IO uint32_t CONFIG; /*!< Configuration of parity and hardware flow control register. */ + __I uint32_t RESERVED12[675]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_UART_Type; + + +/* ================================================================================ */ +/* ================ SPI ================ */ +/* ================================================================================ */ + + +/** + * @brief SPI master 0. (SPI) + */ + +typedef struct { /*!< SPI Structure */ + __I uint32_t RESERVED0[66]; + __IO uint32_t EVENTS_READY; /*!< TXD byte sent and RXD byte received. */ + __I uint32_t RESERVED1[126]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED2[125]; + __IO uint32_t ENABLE; /*!< Enable SPI. */ + __I uint32_t RESERVED3; + __IO uint32_t PSELSCK; /*!< Pin select for SCK. */ + __IO uint32_t PSELMOSI; /*!< Pin select for MOSI. */ + __IO uint32_t PSELMISO; /*!< Pin select for MISO. */ + __I uint32_t RESERVED4; + __I uint32_t RXD; /*!< RX data. */ + __IO uint32_t TXD; /*!< TX data. */ + __I uint32_t RESERVED5; + __IO uint32_t FREQUENCY; /*!< SPI frequency */ + __I uint32_t RESERVED6[11]; + __IO uint32_t CONFIG; /*!< Configuration register. */ + __I uint32_t RESERVED7[681]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_SPI_Type; + + +/* ================================================================================ */ +/* ================ TWI ================ */ +/* ================================================================================ */ + + +/** + * @brief Two-wire interface master 0. (TWI) + */ + +typedef struct { /*!< TWI Structure */ + __O uint32_t TASKS_STARTRX; /*!< Start 2-Wire master receive sequence. */ + __I uint32_t RESERVED0; + __O uint32_t TASKS_STARTTX; /*!< Start 2-Wire master transmit sequence. */ + __I uint32_t RESERVED1[2]; + __O uint32_t TASKS_STOP; /*!< Stop 2-Wire transaction. */ + __I uint32_t RESERVED2; + __O uint32_t TASKS_SUSPEND; /*!< Suspend 2-Wire transaction. */ + __O uint32_t TASKS_RESUME; /*!< Resume 2-Wire transaction. */ + __I uint32_t RESERVED3[56]; + __IO uint32_t EVENTS_STOPPED; /*!< Two-wire stopped. */ + __IO uint32_t EVENTS_RXDREADY; /*!< Two-wire ready to deliver new RXD byte received. */ + __I uint32_t RESERVED4[4]; + __IO uint32_t EVENTS_TXDSENT; /*!< Two-wire finished sending last TXD byte. */ + __I uint32_t RESERVED5; + __IO uint32_t EVENTS_ERROR; /*!< Two-wire error detected. */ + __I uint32_t RESERVED6[4]; + __IO uint32_t EVENTS_BB; /*!< Two-wire byte boundary. */ + __I uint32_t RESERVED7[3]; + __IO uint32_t EVENTS_SUSPENDED; /*!< Two-wire suspended. */ + __I uint32_t RESERVED8[45]; + __IO uint32_t SHORTS; /*!< Shortcuts for TWI. */ + __I uint32_t RESERVED9[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED10[110]; + __IO uint32_t ERRORSRC; /*!< Two-wire error source. Write error field to 1 to clear error. */ + __I uint32_t RESERVED11[14]; + __IO uint32_t ENABLE; /*!< Enable two-wire master. */ + __I uint32_t RESERVED12; + __IO uint32_t PSELSCL; /*!< Pin select for SCL. */ + __IO uint32_t PSELSDA; /*!< Pin select for SDA. */ + __I uint32_t RESERVED13[2]; + __I uint32_t RXD; /*!< RX data register. */ + __IO uint32_t TXD; /*!< TX data register. */ + __I uint32_t RESERVED14; + __IO uint32_t FREQUENCY; /*!< Two-wire frequency. */ + __I uint32_t RESERVED15[24]; + __IO uint32_t ADDRESS; /*!< Address used in the two-wire transfer. */ + __I uint32_t RESERVED16[668]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_TWI_Type; + + +/* ================================================================================ */ +/* ================ SPIS ================ */ +/* ================================================================================ */ + + +/** + * @brief SPI slave 1. (SPIS) + */ + +typedef struct { /*!< SPIS Structure */ + __I uint32_t RESERVED0[9]; + __O uint32_t TASKS_ACQUIRE; /*!< Acquire SPI semaphore. */ + __O uint32_t TASKS_RELEASE; /*!< Release SPI semaphore. */ + __I uint32_t RESERVED1[54]; + __IO uint32_t EVENTS_END; /*!< Granted transaction completed. */ + __I uint32_t RESERVED2[2]; + __IO uint32_t EVENTS_ENDRX; /*!< End of RXD buffer reached */ + __I uint32_t RESERVED3[5]; + __IO uint32_t EVENTS_ACQUIRED; /*!< Semaphore acquired. */ + __I uint32_t RESERVED4[53]; + __IO uint32_t SHORTS; /*!< Shortcuts for SPIS. */ + __I uint32_t RESERVED5[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED6[61]; + __I uint32_t SEMSTAT; /*!< Semaphore status. */ + __I uint32_t RESERVED7[15]; + __IO uint32_t STATUS; /*!< Status from last transaction. */ + __I uint32_t RESERVED8[47]; + __IO uint32_t ENABLE; /*!< Enable SPIS. */ + __I uint32_t RESERVED9; + __IO uint32_t PSELSCK; /*!< Pin select for SCK. */ + __IO uint32_t PSELMISO; /*!< Pin select for MISO. */ + __IO uint32_t PSELMOSI; /*!< Pin select for MOSI. */ + __IO uint32_t PSELCSN; /*!< Pin select for CSN. */ + __I uint32_t RESERVED10[7]; + __IO uint32_t RXDPTR; /*!< RX data pointer. */ + __IO uint32_t MAXRX; /*!< Maximum number of bytes in the receive buffer. */ + __I uint32_t AMOUNTRX; /*!< Number of bytes received in last granted transaction. */ + __I uint32_t RESERVED11; + __IO uint32_t TXDPTR; /*!< TX data pointer. */ + __IO uint32_t MAXTX; /*!< Maximum number of bytes in the transmit buffer. */ + __I uint32_t AMOUNTTX; /*!< Number of bytes transmitted in last granted transaction. */ + __I uint32_t RESERVED12; + __IO uint32_t CONFIG; /*!< Configuration register. */ + __I uint32_t RESERVED13; + __IO uint32_t DEF; /*!< Default character. */ + __I uint32_t RESERVED14[24]; + __IO uint32_t ORC; /*!< Over-read character. */ + __I uint32_t RESERVED15[654]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_SPIS_Type; + + +/* ================================================================================ */ +/* ================ SPIM ================ */ +/* ================================================================================ */ + + +/** + * @brief SPI master with easyDMA 1. (SPIM) + */ + +typedef struct { /*!< SPIM Structure */ + __I uint32_t RESERVED0[4]; + __O uint32_t TASKS_START; /*!< Start SPI transaction. */ + __O uint32_t TASKS_STOP; /*!< Stop SPI transaction. */ + __I uint32_t RESERVED1; + __O uint32_t TASKS_SUSPEND; /*!< Suspend SPI transaction. */ + __O uint32_t TASKS_RESUME; /*!< Resume SPI transaction. */ + __I uint32_t RESERVED2[56]; + __IO uint32_t EVENTS_STOPPED; /*!< SPI transaction has stopped. */ + __I uint32_t RESERVED3[2]; + __IO uint32_t EVENTS_ENDRX; /*!< End of RXD buffer reached. */ + __I uint32_t RESERVED4[3]; + __IO uint32_t EVENTS_ENDTX; /*!< End of TXD buffer reached. */ + __I uint32_t RESERVED5[10]; + __IO uint32_t EVENTS_STARTED; /*!< Transaction started. */ + __I uint32_t RESERVED6[109]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED7[125]; + __IO uint32_t ENABLE; /*!< Enable SPIM. */ + __I uint32_t RESERVED8; + SPIM_PSEL_Type PSEL; /*!< Pin select configuration. */ + __I uint32_t RESERVED9[4]; + __IO uint32_t FREQUENCY; /*!< SPI frequency. */ + __I uint32_t RESERVED10[3]; + SPIM_RXD_Type RXD; /*!< RXD EasyDMA configuration and status. */ + __I uint32_t RESERVED11; + SPIM_TXD_Type TXD; /*!< TXD EasyDMA configuration and status. */ + __I uint32_t RESERVED12; + __IO uint32_t CONFIG; /*!< Configuration register. */ + __I uint32_t RESERVED13[26]; + __IO uint32_t ORC; /*!< Over-read character. */ + __I uint32_t RESERVED14[654]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_SPIM_Type; + + +/* ================================================================================ */ +/* ================ GPIOTE ================ */ +/* ================================================================================ */ + + +/** + * @brief GPIO tasks and events. (GPIOTE) + */ + +typedef struct { /*!< GPIOTE Structure */ + __O uint32_t TASKS_OUT[4]; /*!< Tasks asssociated with GPIOTE channels. */ + __I uint32_t RESERVED0[60]; + __IO uint32_t EVENTS_IN[4]; /*!< Tasks asssociated with GPIOTE channels. */ + __I uint32_t RESERVED1[27]; + __IO uint32_t EVENTS_PORT; /*!< Event generated from multiple pins. */ + __I uint32_t RESERVED2[97]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[129]; + __IO uint32_t CONFIG[4]; /*!< Channel configuration registers. */ + __I uint32_t RESERVED4[695]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_GPIOTE_Type; + + +/* ================================================================================ */ +/* ================ ADC ================ */ +/* ================================================================================ */ + + +/** + * @brief Analog to digital converter. (ADC) + */ + +typedef struct { /*!< ADC Structure */ + __O uint32_t TASKS_START; /*!< Start an ADC conversion. */ + __O uint32_t TASKS_STOP; /*!< Stop ADC. */ + __I uint32_t RESERVED0[62]; + __IO uint32_t EVENTS_END; /*!< ADC conversion complete. */ + __I uint32_t RESERVED1[128]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED2[61]; + __I uint32_t BUSY; /*!< ADC busy register. */ + __I uint32_t RESERVED3[63]; + __IO uint32_t ENABLE; /*!< ADC enable. */ + __IO uint32_t CONFIG; /*!< ADC configuration register. */ + __I uint32_t RESULT; /*!< Result of ADC conversion. */ + __I uint32_t RESERVED4[700]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_ADC_Type; + + +/* ================================================================================ */ +/* ================ TIMER ================ */ +/* ================================================================================ */ + + +/** + * @brief Timer 0. (TIMER) + */ + +typedef struct { /*!< TIMER Structure */ + __O uint32_t TASKS_START; /*!< Start Timer. */ + __O uint32_t TASKS_STOP; /*!< Stop Timer. */ + __O uint32_t TASKS_COUNT; /*!< Increment Timer (In counter mode). */ + __O uint32_t TASKS_CLEAR; /*!< Clear timer. */ + __O uint32_t TASKS_SHUTDOWN; /*!< Shutdown timer. */ + __I uint32_t RESERVED0[11]; + __O uint32_t TASKS_CAPTURE[4]; /*!< Capture Timer value to CC[n] registers. */ + __I uint32_t RESERVED1[60]; + __IO uint32_t EVENTS_COMPARE[4]; /*!< Compare event on CC[n] match. */ + __I uint32_t RESERVED2[44]; + __IO uint32_t SHORTS; /*!< Shortcuts for Timer. */ + __I uint32_t RESERVED3[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED4[126]; + __IO uint32_t MODE; /*!< Timer Mode selection. */ + __IO uint32_t BITMODE; /*!< Sets timer behaviour. */ + __I uint32_t RESERVED5; + __IO uint32_t PRESCALER; /*!< 4-bit prescaler to source clock frequency (max value 9). Source + clock frequency is divided by 2^SCALE. */ + __I uint32_t RESERVED6[11]; + __IO uint32_t CC[4]; /*!< Capture/compare registers. */ + __I uint32_t RESERVED7[683]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_TIMER_Type; + + +/* ================================================================================ */ +/* ================ RTC ================ */ +/* ================================================================================ */ + + +/** + * @brief Real time counter 0. (RTC) + */ + +typedef struct { /*!< RTC Structure */ + __O uint32_t TASKS_START; /*!< Start RTC Counter. */ + __O uint32_t TASKS_STOP; /*!< Stop RTC Counter. */ + __O uint32_t TASKS_CLEAR; /*!< Clear RTC Counter. */ + __O uint32_t TASKS_TRIGOVRFLW; /*!< Set COUNTER to 0xFFFFFFF0. */ + __I uint32_t RESERVED0[60]; + __IO uint32_t EVENTS_TICK; /*!< Event on COUNTER increment. */ + __IO uint32_t EVENTS_OVRFLW; /*!< Event on COUNTER overflow. */ + __I uint32_t RESERVED1[14]; + __IO uint32_t EVENTS_COMPARE[4]; /*!< Compare event on CC[n] match. */ + __I uint32_t RESERVED2[109]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[13]; + __IO uint32_t EVTEN; /*!< Configures event enable routing to PPI for each RTC event. */ + __IO uint32_t EVTENSET; /*!< Enable events routing to PPI. The reading of this register gives + the value of EVTEN. */ + __IO uint32_t EVTENCLR; /*!< Disable events routing to PPI. The reading of this register + gives the value of EVTEN. */ + __I uint32_t RESERVED4[110]; + __I uint32_t COUNTER; /*!< Current COUNTER value. */ + __IO uint32_t PRESCALER; /*!< 12-bit prescaler for COUNTER frequency (32768/(PRESCALER+1)). + Must be written when RTC is STOPed. */ + __I uint32_t RESERVED5[13]; + __IO uint32_t CC[4]; /*!< Capture/compare registers. */ + __I uint32_t RESERVED6[683]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_RTC_Type; + + +/* ================================================================================ */ +/* ================ TEMP ================ */ +/* ================================================================================ */ + + +/** + * @brief Temperature Sensor. (TEMP) + */ + +typedef struct { /*!< TEMP Structure */ + __O uint32_t TASKS_START; /*!< Start temperature measurement. */ + __O uint32_t TASKS_STOP; /*!< Stop temperature measurement. */ + __I uint32_t RESERVED0[62]; + __IO uint32_t EVENTS_DATARDY; /*!< Temperature measurement complete, data ready event. */ + __I uint32_t RESERVED1[128]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED2[127]; + __I int32_t TEMP; /*!< Die temperature in degC, 2's complement format, 0.25 degC pecision. */ + __I uint32_t RESERVED3[700]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_TEMP_Type; + + +/* ================================================================================ */ +/* ================ RNG ================ */ +/* ================================================================================ */ + + +/** + * @brief Random Number Generator. (RNG) + */ + +typedef struct { /*!< RNG Structure */ + __O uint32_t TASKS_START; /*!< Start the random number generator. */ + __O uint32_t TASKS_STOP; /*!< Stop the random number generator. */ + __I uint32_t RESERVED0[62]; + __IO uint32_t EVENTS_VALRDY; /*!< New random number generated and written to VALUE register. */ + __I uint32_t RESERVED1[63]; + __IO uint32_t SHORTS; /*!< Shortcuts for the RNG. */ + __I uint32_t RESERVED2[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register */ + __I uint32_t RESERVED3[126]; + __IO uint32_t CONFIG; /*!< Configuration register. */ + __I uint32_t VALUE; /*!< RNG random number. */ + __I uint32_t RESERVED4[700]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_RNG_Type; + + +/* ================================================================================ */ +/* ================ ECB ================ */ +/* ================================================================================ */ + + +/** + * @brief AES ECB Mode Encryption. (ECB) + */ + +typedef struct { /*!< ECB Structure */ + __O uint32_t TASKS_STARTECB; /*!< Start ECB block encrypt. If a crypto operation is running, this + will not initiate a new encryption and the ERRORECB event will + be triggered. */ + __O uint32_t TASKS_STOPECB; /*!< Stop current ECB encryption. If a crypto operation is running, + this will will trigger the ERRORECB event. */ + __I uint32_t RESERVED0[62]; + __IO uint32_t EVENTS_ENDECB; /*!< ECB block encrypt complete. */ + __IO uint32_t EVENTS_ERRORECB; /*!< ECB block encrypt aborted due to a STOPECB task or due to an + error. */ + __I uint32_t RESERVED1[127]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED2[126]; + __IO uint32_t ECBDATAPTR; /*!< ECB block encrypt memory pointer. */ + __I uint32_t RESERVED3[701]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_ECB_Type; + + +/* ================================================================================ */ +/* ================ AAR ================ */ +/* ================================================================================ */ + + +/** + * @brief Accelerated Address Resolver. (AAR) + */ + +typedef struct { /*!< AAR Structure */ + __O uint32_t TASKS_START; /*!< Start resolving addresses based on IRKs specified in the IRK + data structure. */ + __I uint32_t RESERVED0; + __O uint32_t TASKS_STOP; /*!< Stop resolving addresses. */ + __I uint32_t RESERVED1[61]; + __IO uint32_t EVENTS_END; /*!< Address resolution procedure completed. */ + __IO uint32_t EVENTS_RESOLVED; /*!< Address resolved. */ + __IO uint32_t EVENTS_NOTRESOLVED; /*!< Address not resolved. */ + __I uint32_t RESERVED2[126]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[61]; + __I uint32_t STATUS; /*!< Resolution status. */ + __I uint32_t RESERVED4[63]; + __IO uint32_t ENABLE; /*!< Enable AAR. */ + __IO uint32_t NIRK; /*!< Number of Identity root Keys in the IRK data structure. */ + __IO uint32_t IRKPTR; /*!< Pointer to the IRK data structure. */ + __I uint32_t RESERVED5; + __IO uint32_t ADDRPTR; /*!< Pointer to the resolvable address (6 bytes). */ + __IO uint32_t SCRATCHPTR; /*!< Pointer to a "scratch" data area used for temporary storage + during resolution. A minimum of 3 bytes must be reserved. */ + __I uint32_t RESERVED6[697]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_AAR_Type; + + +/* ================================================================================ */ +/* ================ CCM ================ */ +/* ================================================================================ */ + + +/** + * @brief AES CCM Mode Encryption. (CCM) + */ + +typedef struct { /*!< CCM Structure */ + __O uint32_t TASKS_KSGEN; /*!< Start generation of key-stream. This operation will stop by + itself when completed. */ + __O uint32_t TASKS_CRYPT; /*!< Start encrypt/decrypt. This operation will stop by itself when + completed. */ + __O uint32_t TASKS_STOP; /*!< Stop encrypt/decrypt. */ + __I uint32_t RESERVED0[61]; + __IO uint32_t EVENTS_ENDKSGEN; /*!< Keystream generation completed. */ + __IO uint32_t EVENTS_ENDCRYPT; /*!< Encrypt/decrypt completed. */ + __IO uint32_t EVENTS_ERROR; /*!< Error happened. */ + __I uint32_t RESERVED1[61]; + __IO uint32_t SHORTS; /*!< Shortcuts for the CCM. */ + __I uint32_t RESERVED2[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[61]; + __I uint32_t MICSTATUS; /*!< CCM RX MIC check result. */ + __I uint32_t RESERVED4[63]; + __IO uint32_t ENABLE; /*!< CCM enable. */ + __IO uint32_t MODE; /*!< Operation mode. */ + __IO uint32_t CNFPTR; /*!< Pointer to a data structure holding AES key and NONCE vector. */ + __IO uint32_t INPTR; /*!< Pointer to the input packet. */ + __IO uint32_t OUTPTR; /*!< Pointer to the output packet. */ + __IO uint32_t SCRATCHPTR; /*!< Pointer to a "scratch" data area used for temporary storage + during resolution. A minimum of 43 bytes must be reserved. */ + __I uint32_t RESERVED5[697]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_CCM_Type; + + +/* ================================================================================ */ +/* ================ WDT ================ */ +/* ================================================================================ */ + + +/** + * @brief Watchdog Timer. (WDT) + */ + +typedef struct { /*!< WDT Structure */ + __O uint32_t TASKS_START; /*!< Start the watchdog. */ + __I uint32_t RESERVED0[63]; + __IO uint32_t EVENTS_TIMEOUT; /*!< Watchdog timeout. */ + __I uint32_t RESERVED1[128]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED2[61]; + __I uint32_t RUNSTATUS; /*!< Watchdog running status. */ + __I uint32_t REQSTATUS; /*!< Request status. */ + __I uint32_t RESERVED3[63]; + __IO uint32_t CRV; /*!< Counter reload value in number of 32kiHz clock cycles. */ + __IO uint32_t RREN; /*!< Reload request enable. */ + __IO uint32_t CONFIG; /*!< Configuration register. */ + __I uint32_t RESERVED4[60]; + __O uint32_t RR[8]; /*!< Reload requests registers. */ + __I uint32_t RESERVED5[631]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_WDT_Type; + + +/* ================================================================================ */ +/* ================ QDEC ================ */ +/* ================================================================================ */ + + +/** + * @brief Rotary decoder. (QDEC) + */ + +typedef struct { /*!< QDEC Structure */ + __O uint32_t TASKS_START; /*!< Start the quadrature decoder. */ + __O uint32_t TASKS_STOP; /*!< Stop the quadrature decoder. */ + __O uint32_t TASKS_READCLRACC; /*!< Transfers the content from ACC registers to ACCREAD registers, + and clears the ACC registers. */ + __I uint32_t RESERVED0[61]; + __IO uint32_t EVENTS_SAMPLERDY; /*!< A new sample is written to the sample register. */ + __IO uint32_t EVENTS_REPORTRDY; /*!< REPORTPER number of samples accumulated in ACC register, and + ACC register different than zero. */ + __IO uint32_t EVENTS_ACCOF; /*!< ACC or ACCDBL register overflow. */ + __I uint32_t RESERVED1[61]; + __IO uint32_t SHORTS; /*!< Shortcuts for the QDEC. */ + __I uint32_t RESERVED2[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[125]; + __IO uint32_t ENABLE; /*!< Enable the QDEC. */ + __IO uint32_t LEDPOL; /*!< LED output pin polarity. */ + __IO uint32_t SAMPLEPER; /*!< Sample period. */ + __I int32_t SAMPLE; /*!< Motion sample value. */ + __IO uint32_t REPORTPER; /*!< Number of samples to generate an EVENT_REPORTRDY. */ + __I int32_t ACC; /*!< Accumulated valid transitions register. */ + __I int32_t ACCREAD; /*!< Snapshot of ACC register. Value generated by the TASKS_READCLEACC + task. */ + __IO uint32_t PSELLED; /*!< Pin select for LED output. */ + __IO uint32_t PSELA; /*!< Pin select for phase A input. */ + __IO uint32_t PSELB; /*!< Pin select for phase B input. */ + __IO uint32_t DBFEN; /*!< Enable debouncer input filters. */ + __I uint32_t RESERVED4[5]; + __IO uint32_t LEDPRE; /*!< Time LED is switched ON before the sample. */ + __I uint32_t ACCDBL; /*!< Accumulated double (error) transitions register. */ + __I uint32_t ACCDBLREAD; /*!< Snapshot of ACCDBL register. Value generated by the TASKS_READCLEACC + task. */ + __I uint32_t RESERVED5[684]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_QDEC_Type; + + +/* ================================================================================ */ +/* ================ LPCOMP ================ */ +/* ================================================================================ */ + + +/** + * @brief Low power comparator. (LPCOMP) + */ + +typedef struct { /*!< LPCOMP Structure */ + __O uint32_t TASKS_START; /*!< Start the comparator. */ + __O uint32_t TASKS_STOP; /*!< Stop the comparator. */ + __O uint32_t TASKS_SAMPLE; /*!< Sample comparator value. */ + __I uint32_t RESERVED0[61]; + __IO uint32_t EVENTS_READY; /*!< LPCOMP is ready and output is valid. */ + __IO uint32_t EVENTS_DOWN; /*!< Input voltage crossed the threshold going down. */ + __IO uint32_t EVENTS_UP; /*!< Input voltage crossed the threshold going up. */ + __IO uint32_t EVENTS_CROSS; /*!< Input voltage crossed the threshold in any direction. */ + __I uint32_t RESERVED1[60]; + __IO uint32_t SHORTS; /*!< Shortcuts for the LPCOMP. */ + __I uint32_t RESERVED2[64]; + __IO uint32_t INTENSET; /*!< Interrupt enable set register. */ + __IO uint32_t INTENCLR; /*!< Interrupt enable clear register. */ + __I uint32_t RESERVED3[61]; + __I uint32_t RESULT; /*!< Result of last compare. */ + __I uint32_t RESERVED4[63]; + __IO uint32_t ENABLE; /*!< Enable the LPCOMP. */ + __IO uint32_t PSEL; /*!< Input pin select. */ + __IO uint32_t REFSEL; /*!< Reference select. */ + __IO uint32_t EXTREFSEL; /*!< External reference select. */ + __I uint32_t RESERVED5[4]; + __IO uint32_t ANADETECT; /*!< Analog detect configuration. */ + __I uint32_t RESERVED6[694]; + __IO uint32_t POWER; /*!< Peripheral power control. */ +} NRF_LPCOMP_Type; + + +/* ================================================================================ */ +/* ================ SWI ================ */ +/* ================================================================================ */ + + +/** + * @brief SW Interrupts. (SWI) + */ + +typedef struct { /*!< SWI Structure */ + __I uint32_t UNUSED; /*!< Unused. */ +} NRF_SWI_Type; + + +/* ================================================================================ */ +/* ================ NVMC ================ */ +/* ================================================================================ */ + + +/** + * @brief Non Volatile Memory Controller. (NVMC) + */ + +typedef struct { /*!< NVMC Structure */ + __I uint32_t RESERVED0[256]; + __I uint32_t READY; /*!< Ready flag. */ + __I uint32_t RESERVED1[64]; + __IO uint32_t CONFIG; /*!< Configuration register. */ + + union { + __IO uint32_t ERASEPCR1; /*!< Register for erasing a non-protected non-volatile memory page. */ + __IO uint32_t ERASEPAGE; /*!< Register for erasing a non-protected non-volatile memory page. */ + }; + __IO uint32_t ERASEALL; /*!< Register for erasing all non-volatile user memory. */ + __IO uint32_t ERASEPCR0; /*!< Register for erasing a protected non-volatile memory page. */ + __IO uint32_t ERASEUICR; /*!< Register for start erasing User Information Congfiguration Registers. */ +} NRF_NVMC_Type; + + +/* ================================================================================ */ +/* ================ PPI ================ */ +/* ================================================================================ */ + + +/** + * @brief PPI controller. (PPI) + */ + +typedef struct { /*!< PPI Structure */ + PPI_TASKS_CHG_Type TASKS_CHG[4]; /*!< Channel group tasks. */ + __I uint32_t RESERVED0[312]; + __IO uint32_t CHEN; /*!< Channel enable. */ + __IO uint32_t CHENSET; /*!< Channel enable set. */ + __IO uint32_t CHENCLR; /*!< Channel enable clear. */ + __I uint32_t RESERVED1; + PPI_CH_Type CH[16]; /*!< PPI Channel. */ + __I uint32_t RESERVED2[156]; + __IO uint32_t CHG[4]; /*!< Channel group configuration. */ +} NRF_PPI_Type; + + +/* ================================================================================ */ +/* ================ FICR ================ */ +/* ================================================================================ */ + + +/** + * @brief Factory Information Configuration. (FICR) + */ + +typedef struct { /*!< FICR Structure */ + __I uint32_t RESERVED0[4]; + __I uint32_t CODEPAGESIZE; /*!< Code memory page size in bytes. */ + __I uint32_t CODESIZE; /*!< Code memory size in pages. */ + __I uint32_t RESERVED1[4]; + __I uint32_t CLENR0; /*!< Length of code region 0 in bytes. */ + __I uint32_t PPFC; /*!< Pre-programmed factory code present. */ + __I uint32_t RESERVED2; + __I uint32_t NUMRAMBLOCK; /*!< Number of individualy controllable RAM blocks. */ + + union { + __I uint32_t SIZERAMBLOCK[4]; /*!< Deprecated array of size of RAM block in bytes. This name is + kept for backward compatinility purposes. Use SIZERAMBLOCKS + instead. */ + __I uint32_t SIZERAMBLOCKS; /*!< Size of RAM blocks in bytes. */ + }; + __I uint32_t RESERVED3[5]; + __I uint32_t CONFIGID; /*!< Configuration identifier. */ + __I uint32_t DEVICEID[2]; /*!< Device identifier. */ + __I uint32_t RESERVED4[6]; + __I uint32_t ER[4]; /*!< Encryption root. */ + __I uint32_t IR[4]; /*!< Identity root. */ + __I uint32_t DEVICEADDRTYPE; /*!< Device address type. */ + __I uint32_t DEVICEADDR[2]; /*!< Device address. */ + __I uint32_t OVERRIDEEN; /*!< Radio calibration override enable. */ + __I uint32_t NRF_1MBIT[5]; /*!< Override values for the OVERRIDEn registers in RADIO for NRF_1Mbit + mode. */ + __I uint32_t RESERVED5[10]; + __I uint32_t BLE_1MBIT[5]; /*!< Override values for the OVERRIDEn registers in RADIO for BLE_1Mbit + mode. */ +} NRF_FICR_Type; + + +/* ================================================================================ */ +/* ================ UICR ================ */ +/* ================================================================================ */ + + +/** + * @brief User Information Configuration. (UICR) + */ + +typedef struct { /*!< UICR Structure */ + __IO uint32_t CLENR0; /*!< Length of code region 0. */ + __IO uint32_t RBPCONF; /*!< Readback protection configuration. */ + __IO uint32_t XTALFREQ; /*!< Reset value for CLOCK XTALFREQ register. */ + __I uint32_t RESERVED0; + __I uint32_t FWID; /*!< Firmware ID. */ + + union { + __IO uint32_t NRFFW[15]; /*!< Reserved for Nordic firmware design. */ + __IO uint32_t BOOTLOADERADDR; /*!< Bootloader start address. */ + }; + __IO uint32_t NRFHW[12]; /*!< Reserved for Nordic hardware design. */ + __IO uint32_t CUSTOMER[32]; /*!< Reserved for customer. */ +} NRF_UICR_Type; + + +/* ================================================================================ */ +/* ================ GPIO ================ */ +/* ================================================================================ */ + + +/** + * @brief General purpose input and output. (GPIO) + */ + +typedef struct { /*!< GPIO Structure */ + __I uint32_t RESERVED0[321]; + __IO uint32_t OUT; /*!< Write GPIO port. */ + __IO uint32_t OUTSET; /*!< Set individual bits in GPIO port. */ + __IO uint32_t OUTCLR; /*!< Clear individual bits in GPIO port. */ + __I uint32_t IN; /*!< Read GPIO port. */ + __IO uint32_t DIR; /*!< Direction of GPIO pins. */ + __IO uint32_t DIRSET; /*!< DIR set register. */ + __IO uint32_t DIRCLR; /*!< DIR clear register. */ + __I uint32_t RESERVED1[120]; + __IO uint32_t PIN_CNF[32]; /*!< Configuration of GPIO pins. */ +} NRF_GPIO_Type; + + +/* -------------------- End of section using anonymous unions ------------------- */ +#if defined(__CC_ARM) + #pragma pop +#elif defined(__ICCARM__) + /* leave anonymous unions enabled */ +#elif defined(__GNUC__) + /* anonymous unions are enabled by default */ +#elif defined(__TMS470__) + /* anonymous unions are enabled by default */ +#elif defined(__TASKING__) + #pragma warning restore +#else + #warning Not supported compiler type +#endif + + + + +/* ================================================================================ */ +/* ================ Peripheral memory map ================ */ +/* ================================================================================ */ + +#define NRF_POWER_BASE 0x40000000UL +#define NRF_CLOCK_BASE 0x40000000UL +#define NRF_MPU_BASE 0x40000000UL +#define NRF_AMLI_BASE 0x40000000UL +#define NRF_RADIO_BASE 0x40001000UL +#define NRF_UART0_BASE 0x40002000UL +#define NRF_SPI0_BASE 0x40003000UL +#define NRF_TWI0_BASE 0x40003000UL +#define NRF_SPI1_BASE 0x40004000UL +#define NRF_TWI1_BASE 0x40004000UL +#define NRF_SPIS1_BASE 0x40004000UL +#define NRF_SPIM1_BASE 0x40004000UL +#define NRF_GPIOTE_BASE 0x40006000UL +#define NRF_ADC_BASE 0x40007000UL +#define NRF_TIMER0_BASE 0x40008000UL +#define NRF_TIMER1_BASE 0x40009000UL +#define NRF_TIMER2_BASE 0x4000A000UL +#define NRF_RTC0_BASE 0x4000B000UL +#define NRF_TEMP_BASE 0x4000C000UL +#define NRF_RNG_BASE 0x4000D000UL +#define NRF_ECB_BASE 0x4000E000UL +#define NRF_AAR_BASE 0x4000F000UL +#define NRF_CCM_BASE 0x4000F000UL +#define NRF_WDT_BASE 0x40010000UL +#define NRF_RTC1_BASE 0x40011000UL +#define NRF_QDEC_BASE 0x40012000UL +#define NRF_LPCOMP_BASE 0x40013000UL +#define NRF_SWI_BASE 0x40014000UL +#define NRF_NVMC_BASE 0x4001E000UL +#define NRF_PPI_BASE 0x4001F000UL +#define NRF_FICR_BASE 0x10000000UL +#define NRF_UICR_BASE 0x10001000UL +#define NRF_GPIO_BASE 0x50000000UL + + +/* ================================================================================ */ +/* ================ Peripheral declaration ================ */ +/* ================================================================================ */ + +#define NRF_POWER ((NRF_POWER_Type *) NRF_POWER_BASE) +#define NRF_CLOCK ((NRF_CLOCK_Type *) NRF_CLOCK_BASE) +#define NRF_MPU ((NRF_MPU_Type *) NRF_MPU_BASE) +#define NRF_AMLI ((NRF_AMLI_Type *) NRF_AMLI_BASE) +#define NRF_RADIO ((NRF_RADIO_Type *) NRF_RADIO_BASE) +#define NRF_UART0 ((NRF_UART_Type *) NRF_UART0_BASE) +#define NRF_SPI0 ((NRF_SPI_Type *) NRF_SPI0_BASE) +#define NRF_TWI0 ((NRF_TWI_Type *) NRF_TWI0_BASE) +#define NRF_SPI1 ((NRF_SPI_Type *) NRF_SPI1_BASE) +#define NRF_TWI1 ((NRF_TWI_Type *) NRF_TWI1_BASE) +#define NRF_SPIS1 ((NRF_SPIS_Type *) NRF_SPIS1_BASE) +#define NRF_SPIM1 ((NRF_SPIM_Type *) NRF_SPIM1_BASE) +#define NRF_GPIOTE ((NRF_GPIOTE_Type *) NRF_GPIOTE_BASE) +#define NRF_ADC ((NRF_ADC_Type *) NRF_ADC_BASE) +#define NRF_TIMER0 ((NRF_TIMER_Type *) NRF_TIMER0_BASE) +#define NRF_TIMER1 ((NRF_TIMER_Type *) NRF_TIMER1_BASE) +#define NRF_TIMER2 ((NRF_TIMER_Type *) NRF_TIMER2_BASE) +#define NRF_RTC0 ((NRF_RTC_Type *) NRF_RTC0_BASE) +#define NRF_TEMP ((NRF_TEMP_Type *) NRF_TEMP_BASE) +#define NRF_RNG ((NRF_RNG_Type *) NRF_RNG_BASE) +#define NRF_ECB ((NRF_ECB_Type *) NRF_ECB_BASE) +#define NRF_AAR ((NRF_AAR_Type *) NRF_AAR_BASE) +#define NRF_CCM ((NRF_CCM_Type *) NRF_CCM_BASE) +#define NRF_WDT ((NRF_WDT_Type *) NRF_WDT_BASE) +#define NRF_RTC1 ((NRF_RTC_Type *) NRF_RTC1_BASE) +#define NRF_QDEC ((NRF_QDEC_Type *) NRF_QDEC_BASE) +#define NRF_LPCOMP ((NRF_LPCOMP_Type *) NRF_LPCOMP_BASE) +#define NRF_SWI ((NRF_SWI_Type *) NRF_SWI_BASE) +#define NRF_NVMC ((NRF_NVMC_Type *) NRF_NVMC_BASE) +#define NRF_PPI ((NRF_PPI_Type *) NRF_PPI_BASE) +#define NRF_FICR ((NRF_FICR_Type *) NRF_FICR_BASE) +#define NRF_UICR ((NRF_UICR_Type *) NRF_UICR_BASE) +#define NRF_GPIO ((NRF_GPIO_Type *) NRF_GPIO_BASE) + + +/** @} */ /* End of group Device_Peripheral_Registers */ +/** @} */ /* End of group nrf51 */ +/** @} */ /* End of group Nordic Semiconductor */ + +#ifdef __cplusplus +} +#endif + + +#endif /* nrf51_H */ +