Revision 2:a0029473868c, committed 2016-11-06

Comitter:

adamumpsimus

Date:

Sun Nov 06 16:08:04 2016 +0000

Parent:

1:bcbe2cf57840

Commit message:

updated the docs

Changed in this revision

diff -r bcbe2cf57840 -r a0029473868c IP12B512.cpp
--- a/IP12B512.cpp	Fri Nov 04 08:19:09 2016 +0000
+++ b/IP12B512.cpp	Sun Nov 06 16:08:04 2016 +0000
@@ -1,49 +1,6 @@
-/** IP12B512 class.
- *  Main class for comunicating with the IP12B512 SPI RAM.
- */
 #include "IP12B512.h"
 
-/** Constructor: setup the SPI and write to "Status Register" that we are going to use it in "Virtual Chip Mode"
- * 
- * Notes:
- * - the MOSI and MISO pins must have 5k6 pulldown resistors
- * - the SCLK pin has a 5k6 pulldown resistor
- * - the HOLD pin is connected to VCC
- * - the CS pin has a 5k6 pullup resistor
- * 
- * @param pin_mosi the hardware MOSI pin on the board
- * @param pin_miso the hardware MISO pin on the board
- * @param pin_sclk the hardware SCLK pin on the board
- * @param pin_cs the software CS pin on the board (can be any output pin)
- *
- * Example:
- * @code
- *
- * #include "mbed.h"
- * #include "IP12B512.cpp"
- *
- * IP12B512 sram(SPI_MOSI, SPI_MISO, SPI_SCK, D6); // MOSI, MISO, SCK, CS
- *
- * int main() {
- *     // GET SRAM SIZE
- *     uint32_t ram_size = sram.GetRamSize();
- *     printf("ram_size %d\n", ram_size);
- *     
- *     // CLEAR ALL SRAM
- *     sram.ClearAll();
- *     
- *     // WRITE A SINGLE BYTE TO SRAM
- *     uint16_t ram_addr = 0;
- *     uint8_t sent_data = 0x6F;
- *     sram.Write(ram_addr, sent_data);
- *     printf("written at address %d data 0x%02X\n", ram_addr, sent_data);
- *     
- *     // READ A SINGLE BYTE FROM RAM
- *     uint8_t rec_data = sram.Read(ram_addr);
- *     printf("read at address %d data 0x%02X\n", address, rec_data);
- * }
- * @endcode
- */
+// Constructor
 IP12B512::IP12B512(
     PinName pin_mosi, 
     PinName pin_miso, 
@@ -68,7 +25,7 @@
     _cs = 1;
 }
 
-/// Write SRAM in byte mode (sends the most data to SRAM prior to write)
+// Write SRAM in byte mode (sends the most data to SRAM prior to write)
 void IP12B512::Write(uint16_t addr, uint8_t data)
 {
     _cs = 0;
@@ -79,7 +36,7 @@
     _cs = 1;
 }
 
-/// Write SRAM in stream mode (sends the least data to SRAM prior to write)
+// Write SRAM in stream mode (sends the least data to SRAM prior to write)
 void IP12B512::StreamWrite(uint16_t addr, uint8_t *data, uint32_t size)
 {
     uint8_t * p = data;
@@ -96,7 +53,7 @@
     _cs = 1;
 }
 
-/// Read SRAM in byte mode (sends the most data to SRAM prior to read)
+// Read SRAM in byte mode (sends the most data to SRAM prior to read)
 uint8_t IP12B512::Read(uint16_t addr)
 {
     uint8_t data;
@@ -111,7 +68,7 @@
     return data;
 }
 
-/// Read SRAM in stream mode (sends the least data to SRAM prior to read)
+// Read SRAM in stream mode (sends the least data to SRAM prior to read)
 void IP12B512::StreamRead(uint16_t addr, uint8_t *data, uint32_t size)
 {
     uint8_t * p = data;
@@ -128,7 +85,7 @@
     _cs = 1;
 }
 
-/// Fill SRAM with data
+// Fill SRAM with data
 void IP12B512::ClearAll()
 {
     uint32_t ram_size = GetRamSize();
@@ -145,7 +102,7 @@
     _cs = 1;
 }
 
-/// Gets the SRAM size in bytes
+// Gets the SRAM size in bytes
 uint32_t IP12B512::GetRamSize()
 {
     uint8_t data;

diff -r bcbe2cf57840 -r a0029473868c IP12B512.h
--- a/IP12B512.h	Fri Nov 04 08:19:09 2016 +0000
+++ b/IP12B512.h	Sun Nov 06 16:08:04 2016 +0000
@@ -10,20 +10,79 @@
 #define IP12B512_WRSR  0x01 // Write status register
 #define IP12B512_RDMI  0x0E // Read Memory Size
 
+/** IP12B512 class.
+ *  Read/write byte and read/write chunks from/to IP12B512 SPI RAM
+ * 
+ *  PDF manual @ http://www.search-pdf-manuals.com/manual/ipsilog-ip12b512-512k-spi-low-power-serial-sram-46
+ * 
+ * Notes:
+ * - the MOSI and MISO pins must have pulldown resistors (i used 5k6 resistors)
+ * - the SCLK pin has a pulldown resistor (i used 5k6 resistor)
+ * - the HOLD pin is connected directly to VCC
+ * - the CS pin has a pullup resistor (i used 5k6 resistor)
+ *
+ * Example:
+ * @code
+ *
+ * #include "mbed.h"
+ * #include "IP12B512.cpp"
+ *
+ * IP12B512 sram(SPI_MOSI, SPI_MISO, SPI_SCK, D6); // MOSI, MISO, SCK, CS
+ *
+ * int main() {
+ *     // GET SRAM SIZE
+ *     uint32_t ram_size = sram.GetRamSize();
+ *     printf("ram_size %d\n", ram_size);
+ *     
+ *     // CLEAR ALL SRAM
+ *     sram.ClearAll();
+ *     
+ *     // WRITE A SINGLE BYTE TO SRAM
+ *     uint16_t ram_addr = 0;
+ *     uint8_t sent_data = 0x6F;
+ *     sram.Write(ram_addr, sent_data);
+ *     printf("written at address %d data 0x%02X\n", ram_addr, sent_data);
+ *     
+ *     // READ A SINGLE BYTE FROM RAM
+ *     uint8_t rec_data = sram.Read(ram_addr);
+ *     printf("read at address %d data 0x%02X\n", ram_addr, rec_data);
+ * }
+ * @endcode
+ */
 class IP12B512
 {
     public:
+/** Constructor: setup the SPI and write to "Status Register" that we are going to use it in "Virtual Chip Mode"
+ * 
+ * @param pin_mosi the hardware MOSI pin on the board
+ * @param pin_miso the hardware MISO pin on the board
+ * @param pin_sclk the hardware SCLK pin on the board
+ * @param pin_cs the software CS pin on the board (can be any output pin)
+ * 
+ */
         IP12B512(
             PinName pin_mosi, 
             PinName pin_miso, 
             PinName pin_sclk, 
             PinName pin_cs
         );
+/** Write SRAM in byte mode (sends the highest amount of data to SRAM prior to write)
+ */
         void Write(uint16_t addr, uint8_t data);
+/** Write SRAM in stream mode (faster then Write method)
+ */
         void StreamWrite(uint16_t addr, uint8_t *data, uint32_t size);
+/** Read SRAM in byte mode (sends the highest amount of data to SRAM prior to read)
+ */
         uint8_t Read(uint16_t addr);
+/** Read SRAM in stream mode (faster then Read method)
+ */
         void StreamRead(uint16_t addr, uint8_t *data, uint32_t size);
+/** Fill SRAM with data
+ */
         void ClearAll();
+/** Get the SRAM size in bytes
+ */
         uint32_t GetRamSize();
 
     private: